Geotechnical Engineering Commons^™

Experimental And Numerical Investigation On The Effect Of Projectile Mass And Apex Angle On Penetration Depth Into Sandy Soils, Abdul-Rahman K. Osman, Ahmed Elshesheny Dr, Mohamed S. Zahran Dr, Nabil M. Nagy Prof.

Journal of Engineering Research

Projectile penetration in granular soils remains a critical concern in defense engineering and ballistics research. This study presents an experimental and numerical investigation of rigid cone-tip projectile penetration into very dense sand, examining the influence of apex angle and projectile weight on penetration depth. Laboratory experiments were conducted using metallic projectiles with apex angles of 10°, 30°, 60°, and 90° and weights of 2.445, 3.87, 5.33, and 6.81 kg, dropped from a height of 4.295 m into a 500×500×500 mm wooden tank filled with sand to 400 mm height at 95% relative density. Through systematic testing, two empirical correlation …

Microwave Ore Pre-Treatment Review And Process Flowsheet Conceptualization, Baker F. Giyani

Tanzania Journal of Engineering and Technology (TJET)

The global demand for mineral commodities has increased dramatically over the years, and this is largely due to several factors, including technological advancements, industrialization, and a rise in population. Further, the demand keeps increasing because the ore being mined is becoming more complex, and the feed grade is declining over the years, prompting the need for innovative technologies to treat such ores more efficiently. Microwave ore pre-treatment is one of the potential technologies that can be employed to improve process performance. This is possible because ores are composed of both good-microwave heaters and poor microwave heaters, which creates thermal stresses …

Modeling The Influence Of Internal Factors On Vehicular Mobility Performance, Aziz Mdimi

Tanzania Journal of Engineering and Technology (TJET)

Traffic mobility is significantly influenced by road conditions and the internal factors governing vehicular performance. Internal factors play a crucial role in vehicular mobility, influencing vehicles operate and performance. While existing vehicular mobility models primarily address external factors, external factors such as governor, engine, gear train and differential unit remain underexplored. This study formulates a comprehensive model to address this gap, focusing on the internal components that affect vehicular mobility. The proposed model employs both analytical and numerical methods to derive transfer functions for these subsystems using Matrix Laboratory (MATLAB), aiming to capture the dynamic behavior of vehicles under various …

Causes And Consequences Of Inefficient Drilling And Blasting In Mine Development Headings: A Case Study Of Hard Rock Gold Mining Operations In Northern Tanzania, George Bennett

Tanzania Journal of Engineering and Technology (TJET)

Despite the introduction of the perimeter blasting technique at the Tulawaka Gold Mine, the mine continued to suffer from an overbreak of mine development headings, with an average overbreak of 24% every 22 m, which is approximately twice the acceptable 10% overbreak. The causes of this problem include ineffective drilling practices and uneven and excessive charging of explosives, resulting in a slightly high powder factor of 3.94 kg/m3 instead of 3.8 kg/m3, as per the design. The problem of overbreak resulted in ore dilution, a longer mine development cycle time and additional costs of approximately US$ 45 per cut, especially …

Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan

College of Graduate Studies: Theses & Dissertations

The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …

Modeling Of Asphalt Concrete For Cross-Anisotropic Visco-Elasticity And Heterogeneity, Zafrul Hakim Khan

Civil Engineering ETDs

Asphalt Concrete (AC) is a cross-anisotropic viscoelastic material. This study has developed a methodology to backcalculate the cross-anisotropic properties of the AC layer from the Falling Weight Deflectometer (FWD) sensor and pavement response data from embedded sensors inside a pavement section. This study has also developed a two-way coupled Multiscale Finite Element Model (MsFEM) with Phase Field Fracture (PFF) to study the microstructural heterogeneity and damage of the AC layer based on the actual field loadings. A Finite Difference Time Domain (FDTD) and Machine learning-based backcalculation algorithm were developed to determine the layer thickness and dielectric constant from air-coupled Ground …

Initiation Criteria For The Onset Of Geomagnetic Substorms Based On Auroral Observations And Electrojet Current Signatures, Mayowa Michael Kayode-Adeoye

Graduate Theses and Dissertations (2019 - present)

In recent years, several substorm onset criteria have been developed, either from auroral observations (many authors) or from auroral electrojet properties such as those described by (Forsyth et al., 2015; Maimaiti et al., 2019; Newell & Gjerloev, 2011; Partamies et al., 2011) The different criteria are being investigated using a low order physics model of the magnetosphere called WINDMI (Spencer et al., 2009) and inferences are being made in line with the WINDMI model. The model variables will be compared with the criteria for substorm onset proposed by examining the SML index.

The WINDMI model uses solar wind and IMF …

Energy Dissipation In A Sand Damper Under Cyclic Loading, Ehab Sabi

Civil and Environmental Engineering Theses and Dissertations

Various seismic and wind engineering designs and retrofit strategies have been in development to meet structures' proper and safe operation during earthquake and wind excitation. One such method is the addition of fluid and particle dampers, such as sand dampers, in an effort to reduce excessive and dangerous displacements of structures. The present study implements the discrete element method (DEM) to assess the performance of a pressurized sand damper (PSD) and characterize the dissipated energy under cyclic loading. The idea of a PSD is to exploit the increase in shearing resistance of sand under external pressure and the associated ability …

Minimizing Surface Run-Off, Improving Underground Water Recharging, And On-Site Rain Harvesting In The Kathmandu Valley, Ambika P. Adhikari, Keshav Bhattarai

Himalayan Research Papers Archive

Nepal's political institutions and administrative units were thoroughly restructured in 2015 with the promulgation of the new Constitution. Several rural areas were combined to meet the definition of urban threshold criteria to classify rural areas into urban categories. Accordingly, over 3,900 local political and administrative units were amalgamated into 753 units, of which, 293 units are classified as urban. Within these newly defined urban areas, many natural environments have been converted into impervious surfaces such as paved roads, sidewalks, and building roofs. These impervious surfaces have drastically increased the amount of surface run-offs-often termed as "urban floods"--under increasing precipitation caused …

A Review Of Current Construction Guidelines To Inform The Design Of Rammed Earth Houses In Seismically Active Zones, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Sustainability in the materials we use for construction is a prime concern, focusing on reducing the embodied energy and carbon footprints of the materials used. The cement used in concrete products is responsible for a significant proportion of Man's CO2 emissions and its production requires substantial energy input, as do fired clay products. For this reason, products formed from unfired earthen materials are of increasing interest and the current challenges include devising means of robust design for strength and to address durability concerns. One form of earthen construction that employs an in-situ method is rammed earth, and it is a …

Resilient Modulus Of Siliciclastic Unbound Granular Materials Under Repeated Wheel Loading, Siya Rimoyi

Tanzania Journal of Engineering and Technology (TJET)

The Resilient Modulus (Mr) is a fundamental material property input in modern Mechanistic-Empirical (M-E) pavements structural design. Empirical pavement design methods have been in use over a long period during which large databases of four- days-soaked California Bearing Ratio (CBR) values at or near the Maximum Dry Density have been generated in the strength assessments for Unbound Granular Materials (UGMs). In the adoption of the M-E design approach researchers have so far attempted with various degrees of success to develop models to derive resilient modulus from the conventional CBR-based databases. This study provides an extensive laboratory experimental study to investigate …

Development Of Intensity-Duration-Frequency (Idf) Models For Manually Operated Rain Gauge Catchment: A Case Study Of Port Harcourt Metropolis Using 50 Years Rainfall Data, Francis Ogbozige

Tanzania Journal of Engineering and Technology (TJET)

Hydraulic structures such as surface drainages and culverts are usually constructed in urban areas with the intention of draining runoff into nearby streams and rivers in order to avoid flooding. However, most of these structures frequently fail to serve the intended use due to the occurrence of high intensity rainfall accompanied with long duration, which produce runoff discharge higher than their designed capacities. This is common in many developing countries as drainages and culverts are most times constructed without considering hydrological analysis of the catchment. Hence, this research considered Port Harcourt city as a case study by utilizing 50 years …

Characterization Of Landslide Processes From Radar Remote Sensing And Hydromechanical Modeling, Yuankun Xu

Earth Sciences Theses and Dissertations

Landsides are a natural geomorphic process yet a dangerous hazard which annually causes thousands of casualties and billions of property loss in a global scale. Understanding landslide motion kinematics from early initiation to final deposition is critical for monitoring, assessing, and forecasting landslide movement in order to mitigate their hazards. Landslides occur under diverse environmental settings and appear in variable types; however, all types of landslides can be mechanically attributed to shearing failure at the basal surface due to stress regime shift contributed by internal and/or external forcing. Typical internal factors include soil/rock weathering, whereas typical external triggering forces encompass …

Modeling Hydraulic Fracturing Initiation And Propagation In Porous Rock Formationsl, Chang Huang

LSU Doctoral Dissertations

Hydraulic fracturing has long been introduced to the oil and gas industry since the early nineteenth century for both reservoir characterization and reservoir stimulation. Despite the progress made in the last two decades, many challenges still have not been tackled regarding not only the propagation problem but also the initiation problem due to its complexity. The dissertation is divided into two stages, i.e., before and after fracture initiation. The first stage of the research aimed at improving the accuracy in solving the poro-mechanical response of wellbore during fluid injection before a tensile fracture occurs, which is crucial to determine the …

Development Of Multi-Axial Fatigue Retrofits For Lock Gate Components, Logan Verkamp

Graduate Theses and Dissertations

Lock gates are essential infrastructure components to the United State (US) supply chain. They create large cost savings and environmental benefits when compared with traditional methods of transport (freight and rail). Because of the large quantity of goods and dependence on these shipping chains, the US economy can be drastically affected by an unexpected gate closure. Unfortunately, many lock gates within the US have reached or exceeded their designed life. Due to the intensity of cyclic loads and the environment, fatigue cracks have become a prominent issue. Developed cracks near the pintle region (a joint which the gate rotates and …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Spot-R By Triax, Purdue Ect Team

ECT Fact Sheets Archive

Triax’s Spot-r system was developed to tackle the construction industry’s unique safety and productivity challenges, stemming from a demonstrated lack of total jobsite visibility and automatically collected, easily accessible field data. Spot-r by Triax combines a proprietary mesh network with sensor technology to record and transmit previously unattainable workforce and equipment location, activity and safety data within a defined area – all in real-time.

The Spot-r network is installed around the site and operates in a 900 MHz network, with a subset using a cellular connection to forward Spot-r sensor data to Triax’s custom, cloud dashboard. In the hazardous construction …

Purdue’S Biowall, Purdue Ect Team

ECT Fact Sheets Archive

Mechanical ventilation, energy recovery ventilation, and infiltration (air that leaks into a building) are commonly used to introduce fresh air. These are all valid approaches, but a living plant-based filter is an innovative complement to these traditional technologies. A Biowall has the potential to improve indoor air quality while reducing the quantity of air needed for ventilation, creating the potential for energy savings. Figure 1 shows a Biowall prototype being evaluated in the ReNEWW House, a research home located near the Purdue University campus (http://www.renewwhouse.com/).

Mdp (Machine Drive Power) Intelligent Compaction Technology, Purdue Ect Team

ECT Fact Sheets Archive

Caterpillar developed MDP (Machine Drive Power) technology to fill this gap. Rather than an accelerometer and vibratory drum, it uses the principle of rolling resistance to provide indications of soil stiffness. This allows it to perform more reliably on cohesive and granular soils with less variability than accelerometer systems. It also means that the technology can be used on both vibratory and static drum compactors, which are often used on larger sites. While the technology is quite useful on its own, it is even better as a complementary technology to the existing accelerometer-based systems. Contractors who use vibratory soil compactors …

Characterization And Modeling Of Asphalt Concrete For Dynamic Properties And Performances, A S M A. Rahman

Civil Engineering ETDs

The recently developed mechanistic-empirical pavement design guide (MEPDG, also known as Pavement M-E design method) uses the nationally calibrated, binder viscosity-based dynamic modulus predictive model for the design and analysis of asphalt pavements. In this study, this model is assessed for its appropriateness for asphalt-aggregate mixtures typically used in New Mexico. In essence, this study investigates the predictability issue of complex modulus of New Mexico mixes. A total of 54 Superpave mixes with different aggregate gradations, air voids, and binder grades were collected from the mixing plants and from the pavement construction sites. The loose asphalt mixtures were then compacted, …

The Role Of Soil Stiffness In Reverse Fault Rupture Propagation, Moises I. Buelna

Master's Theses

A nonlinear Mohr-Coulomb constitutive model with a strain dependent yield surface and non-associated flow was employed to study the plastic soil properties which affect the rate of surface fault rupture propagation in reverse events. These numerical simulations show a trend for soils with higher stiffness to have a higher rate of rupture propagation. Additionally the study shows the effects of strain softening and hardening on the rate of rupture propagation. Soils which strain harden exhibiting ductile behavior typically require more basal offset to rupture to the surface than soils which strain soften exhibiting brittle behavior. These results agree with our …

Datumate, Purdue Ect Team

ECT Fact Sheets Archive

Datumate is digitally transforming civil engineering processes used in construction, surveying and infrastructure inspection markets with fully automated, highly precise, cost effective and safe tools. It utilizes state-of-the-art image processing and advanced drones and camera technologies dramatically reducing the amount of time surveying crews spend in the field, speeding up construction progress checks and shortening infrastructure inspection duration, while maintaining survey grade accuracy. The intuitive, simple and automated solutions increase productivity by saving field and office time in civil engineering and inspection projects of roads, intersections, stockpile volumes, topography, piping, industrial facilities, bridges, property surveys, building facades, railways, cellular infrastructure …

Technology To Manufacture Oriented Pvc (Pvc-O) Pipes, Purdue Ect Team

ECT Fact Sheets Archive

The development of Molecor´s technology, which is based on the application of a Molecular Orientation process, has delivered a significant turning point in the pipelines sector. With this technological development, the company has begun to manufacture TOM® PVC-O pipes, the most eco-friendly pipes on the market. The Molecor technology enabled eradicating many of the existing disadvantages of thermoplastic pipes.

This technology delivers a clear objective; to provide the water industry with a solution for pipes carrying pressurized water in an environmentally friendly, yet cost efficient manner. This also extends a service life compared to pipeline materials currently in use.

The …

Fluid Isolator, Purdue Ect Team

ECT Fact Sheets Archive

The reliability of concrete infrastructure is vital to ensuring daily life, as well as commerce, can progress without interruption. From the pavement of interstate highways to the driveways and sidewalks in a local neighborhood, concrete is expensive to install and often even more expensive, and intrusive, when it needs to be replaced. Unfortunately, to maintain functionality in winter climates concrete is heavily exposed to deicing salts. This not only affects the roads, driveways, and sidewalks where salt is applied directly, but many other areas such as parking and residential garages where vehicles (and people) will track salt along with water …

Netpoint®, Purdue Ect Team

ECT Fact Sheets Archive

The vast majority of construction scheduling software uses a combination of spreadsheets and Gantt charts for developing and depicting Critical Path Method (CPM) schedules. While this paradigm works for the expert scheduler, it is not conducive to collaboration, and it is prohibitively difficult for non-scheduling experts to understand.

NetPoint® provides a dynamic, visual interface conducive to touch and gestural input. Activities are drawn directly on a time-scale and may be placed on the same row or arranged automatically using codes or the WBS. Such control of the presentation makes it easier to communicate the plan to any type of audience. …

Re-Evaluation Of Acceptance Testing Criteria For Structural Masonry Using The Prism Test Method, James Bristow

UNLV Theses, Dissertations, Professional Papers, and Capstones

The current acceptance criteria for structural masonry in accordance with International Building Code allows for the prism test method to be used. However, without a proper understanding of the effects of variable material properties such as individual masonry unit compressive strength and the various material moduli of elasticity, as well as the effect of field conditions on the unit’s performance, masonry prisms may “fail” to reach the design compressive strength (f’m).

By identifying causes of failure and evaluating the failure magnitude, it is concluded that when the masonry prism test method is utilized for acceptance testing of as-built masonry structures, …

Smartvid.Io, Purdue Ect Team

ECT Fact Sheets Archive

The collection, organization, and retrieval of industrial media is a pervasive challenge that is especially glaring for companies in the AEC industry. Construction projects often generate large volumes of pictures & videos from the field for tracking progress and communicating between engineers, contractors, and subcontractors. It is not uncommon for field personnel to capture hundreds of photos per week on any given jobsite.

Smartvid.io is a cloud-based software solution designed for the specific needs of industrial media. The application’s internal deep-learning engines, collectively nicknamed VINNIE (for ‘Very Intelligent Neural Network for Insight and Evaluation’), use speech and image recognition to …

Hillman Composite Beam (Hcb®), Purdue Ect Team

ECT Fact Sheets Archive

The Hillman-Composite Beam (HCB®), is an innovative structural member for use in highway and railroad bridges as well as marine facilities. The HCB is essentially a lightweight reinforced concrete beam strengthened and protected by a corrosion-resistant and resilient Fiberglass Reinforced Polymer (FRP) shell.

The beam is comprised of three main components, a concrete arch (compression reinforcement), an FRP bottom flange encapsulating steel strands tying the ends of the arch together (tension reinforcement) and the FRP shell. Galvanized Rebar “shear connectors” are used to make the beam composite with the concrete deck in the same manner as pre-stressed concrete beams.

The …

Industrial-Grade Monitoring Solution: Hoistcam, Purdue Ect Team

ECT Fact Sheets Archive

Safety and productivity are top priorities for contractors and industrial operations. Improving either makes a company more profitable and competitive. Technology advancements that can do both are important for every company to consider. HoistCam^TM industrial-grade video monitoring solutions can improve employees’ productivity and workplace safety in the construction industries. HoistCam also improves efficiency of operations and reduces job site accidents resulting in substantial cost savings to a contractor.

HoistCam™ is an integrated, wireless video system. The use of HoistCam eliminates blind lifts, blind spots and can share the live video with anyone, anywhere with solid security and easy control. …

Purdue Ect Report - Fourth Quarter 2016, Purdue Ect Team

ECT Fact Sheets Archive

Fourth Quarter 2016

This is a quarterly report from the Purdue ECT.