Biology and Biomimetic Materials Commons^™

Effect Of Hierarchical Structure And Orientation On Water-Repellent Legs Of Water-Walking Insects, Georgia Hurchalla

Dissertations, Master's Theses and Master's Reports

Some insects have the ability to walk on water surface due to hierarchical leg structure and wax coating. This work presents studies of water strider and fire ant leg immersion force profiles to measure resistance of legs to submersion and show orientation effects. A high-sensitivity microbalance measured force during immersion of insect legs at various angles into water droplets. Legs oriented parallel to water surface could support three to five times as much force before immersion, compared to legs in a perpendicular orientation. Water pressure affects the setae structure differently at parallel and perpendicular approaches, and complete wetting is more …

Analysis Of Vibrational Modes Of Chemically Modified Tone Wood, Madison Flesch

Honors Program Theses

It is generally accepted that every violin has different tone quality in terms of intonation and the depth of the harmonics produced. The best violins are made by experienced luthiers that craft each with precision to produce the best possible tonal quality. The quality of the finished violin is dependent upon both the specific shape and the vibrational response of the wood used in its construction. Because the hard wood used in violin construction is inhomogeneous, the composition and structure of material used is critical to the final product.¹ Luthiers would initially rely on their experience to feel the …

Synthesis And Behavior Characterization Of Multi-Scale Hierarchical Structured Composites, Jacob M. Mayfield

College of Graduate Studies: Theses & Dissertations

The purpose of the synthesis of a multi-scale hierarchical composite material was to create a material with a high specific strength, a low mass, and high strength material. To achieve this the material categorization of the Formlabs Tough V2 resin was conducted. The resin was used in the construction of a bio-mimicry diamond lattice structure. The structure was subjected to compression testing to characterize the material properties. The Tough V2 resin structure combined with cellulose created a multi-scaled material on Macro and Micro levels to show the bio-inspired design to increase the material properties in a favorable manor. The Tough …

An Injectable Thermosensitive Biodegradable Hydrogel Embedded With Snap Containing Plla Microparticles For Sustained Nitric Oxide (No) Delivery For Wound Healing, Nikhil Mittal

Dissertations, Master's Theses and Master's Reports

After injury, wound healing is a complex sequential cascade of events essential for the proper recovery of the wound without the scar formation. Nitric oxide (NO) is a small, endogenous free-radical gas with antimicrobial, vasodilating and growth factor stimulating properties. NO has wide biomedical application especially in wound healing however, its usability is hindered due its administration problem as it is highly unstable.

In this work, poly (l-lactic acid) microparticles encapsulated with NO donor S-nitroso-N-acetyl-D-penicillamine (SNAP) were prepared using water-in-oil-water double emulsion solvent evaporation method for controlled delivery for NO at the specific site. The NO release from SNAP-PLLA microparticles …

Studying Mass And Mechanical Property Changes During The Degradation Of A Bioadhesive With Mass Tracking, Rheology And Magnetoelastic (Me) Sensors, Zhongtian Zhang

Dissertations, Master's Theses and Master's Reports

In this research, the degradable polymer 4-arm poly (ethylene glycol)-glutaric acid-dopamine (PEG-GA-DM₄) was synthesized. The degradation behavior of crosslinked PEG-GA-DM₄ bioadhesive was studied with mass tracking, oscillatory rheology, and magnetoelastic (ME) sensors. Changes in mechanical properties were correlated with both dry mass and wet mass changes during the degradation. The results indicate that the loss of mechanical property in the bioadhesive can take place without losing the dry mass. The mass loss profile cannot describe the degradation behavior completely. In addition to studying the degradation of PEG-GA-DM₄, this research also confirms the application of ME …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

LSU New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Study Of Iron Ion Transit Through Three-Fold Channel Of Ferritin Cage, Shah Alam Limon

Graduate Theses/Dissertations

Ferritin is an iron-storage globular protein with an ability to uptake, mineralize and release iron ions in a controllable manner. The globular hollow shell allows storage of mineralized iron, with several channels responsible for the transit of ions into the shell and out of it. Understanding of the detailed molecular functioning of ferritin is required for rational design of biomimetic conjugate nano-biosystems containing ferritin-like constituents. In this work, ferritin was investigated both numerically by all-atom molecular dynamics (MD) simulations, and experimentally by Raman spectroscopy. Molecular dynamic simulations of a model system comprising iron ions (Fe2+) and a ferritin trimer expressing …

Cellulose Reinforced Thermoplastic Composites By In-Situ Ring-Opening Polymerization, Shahab Kashani Rahimi

Dissertations

Over the past two decades, the increasing concern about the negative environmental impacts of synthetic materials has led to rising interests in utilizing renewable natural resources to develop polymer materials with comparable properties and performance to their synthetic counterparts. One of the major fields of interest is polymer composites where the replacement of synthetic fibers with bio renewable natural fibers is of great potential. However, the processing difficulties, in terms of fiber dispersion and thermal stability have limited the application of cellulosic fibers to polymers with low processing temperatures which are mostly hydrophobic polymers. As a result, the true reinforcing …

An Evaluation Of The Efficiency Of Compartmented Alginate Fibres Encapsulating Rejuvenator As Asphalt Pavement Healing System, Amir Tabakovic, Luke Schuyffel, Aleksandar Karac, Erik Schlangen

Articles

This paper explores the potential methods for evaluating a healing system for asphalt pavements. The healing system under investigation involves compartmented calcium-alginate fibres encapsulating an asphalt binder healing agent (rejuvenator). This system presents a novel method of incorporating rejuvenators into asphalt pavement mixtures. The compartmented fibres are used to distribute the rejuvenator throughout the pavement mixture, thereby overcoming some of the problems associated with alternate asphalt pavement healing methods, i.e., spherical capsules and hollow fibres. The asphalt healing efficiency methods to be evaluated in this paper include: (i) standard test methods for asphalt pavements, such as the Indirect Tensile Strength …

Dual Mechanism For Toughening And Sustained Aminoglycoside Elution From A Polyphosphate Hydrogel, Dwight D. Lane, Russell J. Stewart Phd

Biomedical Engineering Western Regional Conference

No abstract provided.

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …

Study Of Nano-Bio Interfaces In Nano-Bio Conjugates: Nanoparticles Of Zinc Oxide (Zno) And Biomolecules Of Glucose, Cytosine, And Thymine, Bithi Paul

Graduate Theses/Dissertations

Nano conjugates, composites of inorganic nanomaterials and bio molecules such as DNA, RNA and proteins, establish a sequence of wide varieties of nano-bio boundaries. The formation of these boundaries strongly depends on bio physicochemical reaction of biomolecules coated on the surface of nanomaterials. I am investigating various nano-bio conjugates consisting of zinc oxide (ZnO) nanoparticles with simple biomolecules including glucose and the nitrogenous bases of DNA such as cytosine and thymine. All nano-bio conjugates were fabricated using a standard bio-chemical synthesis process. Structural, physical, bio-chemical interface properties of nano-bio composites were probed using X-ray diffraction (XRD), Raman spectroscopy, and photoluminescence …

Bio Inspired Lightweight Composite Material Design For 3d Printing, Kaushik Thiyagarajan

Electronic Theses and Dissertations

Lightweight material design is an indispensable subject in product design. The lightweight material design has high strength to weight ratio which becomes a huge attraction and an area of exploration for the researchers as its application is wide and increasing even in every day-to-day product. Lightweight composite material design is achieved by selection of the cellular structure and its optimization. Cellular structure is used as it has wide multifunctional properties in addition to the lightweight characteristics. Applications of light weight cellular structures are wide and is witnessed in all industries from aerospace to automotive, construction to product design. In this …

Tunable Nanocomposite Membranes For Water Remediation And Separations, Sebastián Hernández Sierra

Theses and Dissertations--Chemical and Materials Engineering

Nano-structured material fabrication using functionalized membranes with polyelectrolytes is a promising research field for water pollution, catalytic and mining applications. These responsive polymers react to external stimuli like temperature, pH, radiation, ionic strength or chemical composition. Such nanomaterials provide novel hybrid properties and can also be self-supported in addition to the membranes.

Polyelectrolytes (as hydrogels) have pH responsiveness. The hydrogel moieties gain or lose protons based on the pH, displaying swelling properties. These responsive materials can be exploited to synthesize metal nanoparticles in situ using their functional groups, or to immobilize other polyelectrolytes and biomolecules. Due to their properties, these …

Electrospinning Novel Aligned Polymer Fiber Structures For Use In Neural Tissue Engineering, Rachel Martin

Dissertations, Master's Theses and Master's Reports

A suitable tissue scaffold to support and assist in the repair of damaged tissues or cells is important for success in clinical trials and for injury recovery. Electrospinning can create a variety of polymer nanofibers and microfibers, and is being widely used to produce experimental tissue scaffolds for neural applications. This dissertation examines various approaches by which electrospinning is being used for neural tissue engineering applications for the repair of injuries to the central nervous system (CNS) and the peripheral nervous system (PNS). Due to the poor regeneration of neural tissues in the event of injury, tissue scaffolds are being …

A 3d Biomimetic Scaffold Using Electrospinning For Tissue Engineering Applications, Samerender Nagam Hanumantharao

Dissertations, Master's Theses and Master's Reports

Electrospinning holds great promise for designing functional 3D biomimetic scaffolds for tissue engineering applications. The technique allows for the reproducible fabrication of 3D scaffolds with control over the porosity and thickness. In this work, a novel method for the synthesis of a 3D electroactive scaffold using electrospinning from polycaprolactone (PCL), Polyvinylidene Fluoride (PVDF) and Polyaniline (PANI) is reported. Additional scaffolds involving different morphologies of PCL, PCL-PVDF and PCL-PANI-PVDF were also fabricated and evaluated. The scaffolds were characterized using electron microscopy to visualize the morphologies. Infrared spectroscopy was used to confirm the presence of polymers and their respective phases in the …

Structural Characteristics And Corrosion Behavior Of Bio-Degradable Zn-Li Alloys In Stent Application, Shan Zhao

Dissertations, Master's Theses and Master's Reports

Zinc has begun to be studied as a bio-degradable material in recent years due to its excellent corrosion rate and optimal biocompatibility. Unfortunately, pure Zn’s intrinsic ultimate tensile strength (UTS; below 120 MPa) is lower than the benchmark (about 300 MPa) for cardiovascular stent materials, raising concerns about sufficient strength to support the blood vessel. Thus, modifying pure Zn to improve its mechanical properties is an important research topic.

In this dissertation project, a new Zn-Li alloy has been developed to retain the outstanding corrosion behavior from Zn while improving the mechanical characteristics and uniform biodegradation once it is implanted …

Fabrication Of Flexible, Biofunctional Architectures From Silk Proteins, Ramendra K. Pal

Theses and Dissertations

Advances in the biomedical field require functional materials and processes that can lead to devices that are biocompatible, and biodegradable while maintaining high performance and mechanical conformability. In this context, a current shift in focus is towards natural polymers as not only the structural but also functional components of such devices. This poses material-specific functionalization and fabrication related questions in the design and fabrication of such systems. Silk protein biopolymers from the silkworm show tremendous promise in this regard due to intrinsic properties: mechanical performance, optical transparency, biocompatibility, biodegradability, processability, and the ability to entrap and stabilize biomolecules. The unique …

Design Of Robust Hydrogel Based On Mussel-Inspired Chemistry, Yuan Liu

Dissertations, Master's Theses and Master's Reports

The structure of catechol is found in mussel adhesive proteins and contributed to both wet-resistant adhesion and cohesive curing of these proteins. A synthetic nano-silicate, Laponite was incorporated into catechol-containing hydrogels and the hydrogel network-bound catechol formed strong reversible interfacial interaction with Laponite. The contribution of incorporated catechol-Laponite reversible interfacial interactions to the mechanics of hydrogels constructed by different strategies was studied. In the first strategy, Laponite and catechol were introduced into the double network hydrogel (DN) via the free radical co-polymerization of a catechol-containing monomer, backbone monomer, and crosslinker. The introduction of catechol-Laponite interactions significantly improved the compressive strength …

Silk As A Biomaterial Paste For Biomimetic Composite, Sang Hyun Park

McKelvey School of Engineering Graduate Student Theses & Dissertations

Silk is a highly promising biomaterial with unique bio-physicochemical properties, such as excellent mechanical and optical properties, biocompatibility and programmable biodegradability. Among many different types, silk from domesticated silkworm, bombyx mori has received wide attention owing to its availability in virtually unlimited quantities and ease of extraction. In this study, we investigated silkworm silk as a protein glue to realize nacre-like composites. We have employed spin assisted layer-by-layer technique to fabricate ultrathin free-standing biocomposite films. Two different composites have been studied: (i) graphene oxide (GO)/silk and (ii) chitin/silk. From our prior work, it is known that the adsorption of amphiphilic …

Dna Bound Avicel Network: The Beginnings Of A Self-Healing Material, Emily R. Coleman, Michael R. Ladisch, Eduardo Ximenes, Marissa Karp, Kathleen Howell, Seockmo Ku, Nathan Mosier, Iman Beheshti Tabar

The Summer Undergraduate Research Fellowship (SURF) Symposium

Self-healing materials could potentially provide many improvements to engineering projects, including reduced maintenance and cost, and increased lifespan. It is desired to create a self-healing material proof of concept, which can then be altered for eventual application to the surfaces of small satellites with the goal of increasing material lifetimes. The intrinsic properties and abilities of DNA base pairing will be studied as a first test of proof of concept. The exploratory research reported in this short communication utilizes oxidation of small (50µm) particles of Avicel using TEMPO, followed by activation of Avicel particles via an EDC (1-Ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride) …

Alginate Hydrogels As Three-Dimensional Scaffolds For In Vitro Culture Models Of Growth Plate Cartilage Development And Porcine Embryo Elongation, Taylor D. Laughlin

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

The establishment of in vitro culture models utilizes tissue engineering principles to design functional mimics of in vivo environments in vitro. Advantages for the use of in vitro culture models include ethical alleviation of animal models for therapeutic testing, cost efficiency, and a greater ability to study specific mechanisms via a systematic, ground-up approach to development. In this thesis, alginate hydrogels are utilized in the development of in vitro culture models of porcine embryo elongation and growth plate cartilage development. First, the effect of scaffold and modifications to the scaffold were explored in both projects. In order to modulate …

Design Of Nanoparticle-Based Carriers For Targeted Drug Delivery, Xiaojiao Yu, Ian Trase, Muqing Ren, Kayla Duval, Xing Guo, Zi Chen

Dartmouth Scholarship

Nanoparticles have shown promise as both drug delivery vehicles and direct antitumor systems, but they must be properly designed in order to maximize efficacy. Computational modeling is often used both to design new nanoparticles and to better understand existing ones. Modeled processes include the release of drugs at the tumor site and the physical interaction between the nanoparticle and cancer cells. In this paper, we provide an overview of three different targeted drug delivery methods (passive targeting, active targeting, and physical targeting) and compare methods of action, advantages, limitations, and the current stages of research. For the most commonly used …

Solution Casting And Mechanical Testing Of Arabinan-Cellulose Nanocomposites, Kevin Su, Alina Lusebrink

Materials Engineering

The purpose of this work was to investigate methods to produce consistent, reliable, and testable thin films of arabinan-cellulose nanocomposites. Mechanical properties and composition of the Opuntia ficus-indica cactus spines served as motivation for this research. The high specific strength and stiffness, biodegradability, and sustainability of these spines inspired the creation of composites fabricated from the same materials found in cactus spines: arabinan and nanocrystalline cellulose (NCC). Arabinan serves as the matrix material and NCC as the reinforcement. To explore the feasibility of using a non-toxic solvent, different solution casting techniques with water as a solvent were investigated. Ultrasonication was …

Reducing Food And Packaging Waste Through Developing Edible Fruit Based Packaging Prototypes, Melanie Thatcher

Materials Engineering

Packaging is used to contain, preserve, protect, and advertise both manufactured and natural products. In 2013 it was reported that over thirty percent of solid waste in the United States was from packaging. One way to reduce the impact of packaging on the environment is to create a solution that is edible and sourced from a waste or secondary food product that is not currently being utilized. Food-contact packaging made from recycled materials must meet strict U.S. Food and Drug Administration (FDA) regulations to be utilized as raw material for packaging. Fruit pomace is a candidate material since it may …

Biomimetic Seal Flipper Test Rig, Gordon D. Belyea, Laura Kawashiri, Dylan Rinker, Kurt Beske

Mechanical Engineering

No abstract provided.

A Numerical Approach To Investigate The Influence Of Deformable Blockages On Blood Flow In An Elastic Vessel, Tai-Hsien Wu

Research and Creative Activities Poster Day

In this work, we presented a new numerical approach to study the deformation of blockages and fluid properties in an elastic blood vessel. In computational hemodynamics, only few of the current numerical models considered the elasticity of vessels, and those models were difficult to extend to other topics like the deformation of blockages in elastic blood vessels. In addition, the approach that we employed is especially effective on visualization. A validation for the present method is carried out by comparing the simulation results with a theoretical prediction of the deformation of the pulmonary blood vessel in a steady flow. Subsequently, …

Inhibition Of Bacterial Growth And Prevention Of Bacterial Adhesion With Localized Nitric Oxide Delivery, Julia Osborne

Dissertations, Master's Theses and Master's Reports

Bacterial infections continue to be a problem at the site of an indwelling medical device, and over the years, various bacterial strains have become more resistant to current antibiotic treatments. Bacterial infection at an indwelling medical device can be dangerous and affect the performance of the medical device which can ultimately lead to the failure of the device due to bacterial resistance to treatment.

Nitric Oxide (NO) has been shown to possess antibacterial properties to prevent and inhibit bacterial growth. NO releasing coatings on indwelling medical devices could provide a reduction in bacterial infections that occur at the device site …

A Platform For Fast Detection Of Let-7 Micro Rna Using Polyaniline Fluorescence And Image Analysis Techniques, Partha P. Sengupta

Master's Theses

The project describes a new strategy for transducing hybridization events through modulating intrinsic properties of the electroconductive polymer polyaniline (PANI). When DNA based probes electrostatically interact with PANI, its fluorescence properties are increased, a phenomenon that can be enhanced by UV irradiation. Hybridization of target nucleic acids results in dissociation of probes causing PANI fluorescence to return to basal levels. By monitoring restoration of base PANI fluorescence as little as 10^-11 M (10 pM) of target oligonucleotides could be detected within 15 minutes of hybridization. Detection of complementary oligos was specific, with introduction of a single mismatch failing to …

Incorporation Of Fibrin Into A Collagen–Glycosaminoglycan Matrix Results In A Scaffold With Improved Mechanical Properties And Enhanced Capacity To Resist Cell-Mediated Contraction, Claire Brougham, Tanya J. Levingstone, Stefan Jockenhoevel, Thomas C. Flanagan, Fergal J. O'Brien

Articles

Fibrin has many uses as a tissue engineering scaffold, however many in vivo studies have shown a reduction in function resulting from the susceptibility of fibrin to cell-mediated contraction. The overall aim of the present study was to develop and characterise a reinforced natural scaffold using fibrin, collagen and glycosaminoglycan (FCG), and to examine the cell-mediated contraction of this scaffold in comparison to fibrin gels. Through the use of an injection loading technique, a homogenous FCG scaffold was developed. Mechanical testing showed a sixfold increase in compressive modulus and a thirtyfold increase in tensile modulus of fibrin when reinforced with …