Biology and Biomimetic Materials Commons^™

Design Principles For Robotic-Controlled 3d Printing Of Soft Tissue-Mimicking Materials, Karina Mealey

Master's Theses

Geometrically and physically accurate 3D models are emerging as essential tools for surgeons in pre-operative planning and training, but current methods of producing these models are not sufficient. Existing solutions have downsides such as high costs, long and tedious production times, high complexity resulting in a lack of scalability, or an inability to meet material requirements for accurately simulating human tissue.

The objective of this work is to develop principles for a low-cost, easy-to-use 3D printing system capable of prototyping with soft tissue-mimicking materials. To pursue this goal, a MyCobot280 robot arm was used as the mechanism to explore the …

Additive Manufacturing For Medical Education, Michael Noon

College of Engineering Summer Undergraduate Research Program

A growing body of evidence is suggesting that anatomical knowledge, the keystone of many medical specialties, is suffering among new graduates. While a host of reasons are provided, one common thread that many point to is the decline of cadaver dissections in the classroom. Many virtual audio-visual tools are used to address this gap, yet evidence has shown their ineffectiveness. Given this gap, the high degree of flexibility found in additive manufacturing (AM), and the many uses AM has already found in the medical field, we propose its use to fill this gap, allowing for students to learn with touch …

Effects Of Uv Exposure On The Thermo-Mechanical Properties Of Cactus Based Biopolymers, Madison Glozer, Megan Bolling, Addison Wolfson

Materials Engineering

The viability of renewable biopolymers as sustainable alternatives to synthetic plastics is promising, however ultra-violet (UV) radiation can lead to premature degradation and reduction in the material’s performance. Biopolymers comprised of nopal cactus juice, animal protein, natural wax, and glycerin in differing percentages were studied to obtain thermo-mechanical data in relation to UV exposure. To quantify degradation, dynamic mechanical analysis, thermogravimetric analysis, differential scanning calorimetry, infrared spectroscopy, goniometry and gravimetric measurements were performed. Each formulation experienced mass loss as a result of UV exposure, which could be attributed to water evaporation. The thermogravimetric analysis indicated a reduction in the second …

Left Atrial Model, Borna Sobati, Sarah Porello, Tess Pate

Biomedical Engineering

The objective is to produce an electrophysiological model of an adult human left atrium. This model will be used to test mapping probe catheters used for locating cardiac arrhythmias against current technology used in practice. Dr. Chris Porterfield requested this model and other physicians or probe catheter manufacturers may also use this product in the future. Dr. Porterfield also discussed the possibility of future senior project groups using the model as a bench test for designing new catheter tips. The model will precisely simulate electrical behaviors of the heart in normal as well as arrhythmic conditions. Ideally, the model will …

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …

Solution Casting And Mechanical Testing Of Arabinan-Cellulose Nanocomposites, Kevin Su, Alina Lusebrink

Materials Engineering

The purpose of this work was to investigate methods to produce consistent, reliable, and testable thin films of arabinan-cellulose nanocomposites. Mechanical properties and composition of the Opuntia ficus-indica cactus spines served as motivation for this research. The high specific strength and stiffness, biodegradability, and sustainability of these spines inspired the creation of composites fabricated from the same materials found in cactus spines: arabinan and nanocrystalline cellulose (NCC). Arabinan serves as the matrix material and NCC as the reinforcement. To explore the feasibility of using a non-toxic solvent, different solution casting techniques with water as a solvent were investigated. Ultrasonication was …

Reducing Food And Packaging Waste Through Developing Edible Fruit Based Packaging Prototypes, Melanie Thatcher

Materials Engineering

Packaging is used to contain, preserve, protect, and advertise both manufactured and natural products. In 2013 it was reported that over thirty percent of solid waste in the United States was from packaging. One way to reduce the impact of packaging on the environment is to create a solution that is edible and sourced from a waste or secondary food product that is not currently being utilized. Food-contact packaging made from recycled materials must meet strict U.S. Food and Drug Administration (FDA) regulations to be utilized as raw material for packaging. Fruit pomace is a candidate material since it may …

Biomimetic Seal Flipper Test Rig, Gordon D. Belyea, Laura Kawashiri, Dylan Rinker, Kurt Beske

Mechanical Engineering

No abstract provided.

Molecular Dynamics Investigation Of The Arabinan-Cellulose Interface For Cellulose Nanocomposite Applications, Luke Thornley

Materials Engineering

Atom level computer simulations of the arabinan and cellulose interface were performed to better understand the mechanisms that give arabinan-cellulose composites (ArCCs) their strength with the goal to improve man-made ArCCs. The molecular dynamics (MD) software LAMMPS was used in conjunction with the ReaxFF/c force field to model the bond between cellulose and arabinan. A cellulose nanocrystal with dimensions 51 x 32 x 8 Å was minimized with various weight percent of water, 0%, 3%, 5%, 8%, 10%, and 12%. After the system was equilibrated for at least 100,000 femtoseconds, an arabinan molecule composed of 8 arabinose rings was added …

Investigating The Cause Of Unique Mechanical Behavior In Platinum Alloy Guidewire Tips, Evan Borgeson, Alfred Rosen

Materials Engineering

The platinum alloy used by Abbott Vascular in guidewire tips exhibits a yielding behavior characterized by an abrupt transition from elastic to plastic zones and high ductility. This yielding behavior was hypothesized to be a result of one of three structural phenomena: ordering, solute strain aging, or interstitial strain aging. To test for these strengthening mechanisms in the wire, X-ray diffraction analysis, heat treatments, and tensile testing were completed. The wire has a diameter of 0.0025 inches and was supplied in two forms, the final stress relieved state, and as-drawn from the production line. Heat treatments were performed at 130 …

Developent Of A Phospholipid Encapsulation Process For Quantum Dots To Be Used In Biologic Applications, Logan Grimes

Master's Theses

The American Cancer Society predicts that 1,665,540 people will be diagnosed with cancer, and 585,720 people will die from cancer in 2014. One of the most common types of cancer in the United States is skin cancer. Melanoma alone is predicted to account for 10,000 of the cancer related deaths in 2014. As a highly mobile and aggressive form of cancer, melanoma is difficult to fight once it has metastasized through the body. Early detection in such varieties of cancer is critical in improving survival rates in afflicted patients. Present methods of detection rely on visual examination of suspicious regions …

Fabrication And Testing Of Arabinan Cellulose Nanocomposites, Ross Johnson, Austin Rosso, Nick Semansky

Materials Engineering

Inspired by the structure and composition of cactus spines found in nature, arabinan-cellulose nanocomposites were fabricated into thin films and tested for mechanical stiffness. The composites consisted of varying amounts of nanocrystalline cellulose reinforcement suspended in an arabinan matrix. Both materials are polysaccharides and are known to be biodegradable and food safe. The thin film samples were tensile tested using a dynamic mechanical analysis machine both as-cast and after a heat-treatment. The heat treatment of the arabinan itself resulted in an order of magnitude increase in stiffness, while the cellulose reinforced composites increased roughly six fold. The arabinan-50 wt% cellulose …

Strength Testing And Material Characterization Of Cactus Spines, Mary Cooper, Jeff Goldstein, Thomas Tarlton

Materials Engineering

Twelve different species of cactus spines from 6 different genera were collected from living specimens and maintained in a dry storage environment. Spines from each species underwent 3-point bend testing, XRD testing, and SEM imaging. XRD analysis was used to verify the presence of cellulose whisker like nanocrystals and to calculate the percent crystallinity of each spine. SEM images were captured of fracture surfaces at viewing angles of 90° and 45° relative to the fracture surface, with magnifications ranging between 150x and 4,000x. A total of six spines from each species were tested in three point bending using a high-resolution …

Development Of A High Precision Quantum Dot Synthysis Method Utilizing A Microfluidic Reactor And In-Line Fluorescence Cell, Harry Lafferty, Jonny Hoadley

Materials Engineering

Quantum dots show great potential for use as spectral converters in solar cells, lighting applications and biological imaging. These applications require precise control of quantum dot size to maximize performance. The fluorescence profile of quantum dots in solution correlates directly with particle size. An alternative, high precision process was developed for the synthesis of cadmium-selenide quantum dots using a microfluidic reactor and fluorescence flow through cell. The process required creating separate cadmium and selenium precursors that were then mixed in a nitrogen environment at 17± 1°C. Using an NE-300^® syringe pump, the solution was pumped through a microfluidic reactor …

An Investigation Of Arabinan And Cellulose Based Nano-Composite Fabrication Methods, Marianne Smithfield, Carl Petterson, Robert Miller

Materials Engineering

Microcrystalline cellulose was converted into nanocrystalline cellulose via an acid hydrolysis procedure. Scanning electron microscopy (SEM) was employed to measure the particle size and thus the effectiveness of acid hydrolysis. The nanocrystalline cellulose was poured through a 0.2μm filter to isolate the particles of ideal size. The nanocrystalline cellulose samples were stored in dimethylformamide (DMF) to prevent mold growth and agglomeration upon drying. Numerous composite samples were created by dissolving the arabinan in a solvent, suspending cellulose in the arabinan solution, and then drying the sample. Casting was performed in a silicon mold to allow sample removal without damage. Initial …

Determining An Inorganic Mineralization Process To Inhibit Organic Degradation And Preserve The Dimensional Stability Of Bamboo, Eric Hahn

Materials Engineering

Bamboo is a renewable natural composite with potential as both a construction and synthesis material. The components of bamboo are cellulosic vascular bundles imbedded within a lignin matrix that create a porous hierarchical structure. This structure has low density while maintaining high strength, toughness, and elasticity, but is susceptible to organic decay. A study was performed to evaluate the effect of varying bamboo culm age (1-3 years) and density (0.72-1.05 g/cm³) on the ability to control inorganic mineral precipitation to prevent degradation and preserve dimensional stability of the organic matrix. Internodal culm samples were immersed in solutions of …

The Characterization And Comparison Of Biochar Produced From A Decentralized Reactor Using Forced Air And Natural Draft Pyrolysis, Leah Herbert, Ian Hosek, Rishi Kripalani

Materials Engineering

The soil additive properties of biochar have proven both effective and globally beneficial, but depend heavily on feedstock used and process conditions. This study characterizes how forced and natural draft air flows affect the biochar’s soil amendment potential. Biochars manufactured from two pine species of feedstock, in timber and pellet form, were compared against a designer biochar. The designer biochar held the lowest C:N ratio (57.43), followed by the natural draft pellets (199.5), forced air timber (282.5), forced air pellets (422.7), and natural draft timber (503.7). The designer char had the largest cation exchange capacity at 138.5 cmolc/kg; the decentralized …

Artificial Alveolar-Capillary Membrane On A Microchip, Keith Male

Materials Engineering

A microfluidic device was synthesized out of polydimethyl siloxane (PDMS) to simulate the structure of the alveolar-capillary interface of the human lung. Soft lithography techniques were used to build a mold structure out of SU-8 epoxy at heights ranging from 30µm to 110 µm on a silicon substrate, with the 70 µm structure working the best. A mixture of 10:1 Sylgard 184 elastomer was then cast using the mold, and cured at a temperature of 80^oC. For the porous membrane, the PDMS was spun on at 6000rpm for 30 seconds using a spin coater to produce a membrane …

The Mitigation Of Eutrophication Using Microporous Polymer Membranes To Control Algae Growth, Christopher R. Riley

Materials Engineering

A system was designed to mitigate the accelerated process of anthropogenic eutrophication. This system aimed to contain Chlorella Vulgaris microalgae cells within an enclosed polymer membrane pouch while allowing for water and nutrients to diffuse through the pouch. As a test model, a 10 gallon aquarium was partitioned into three sections using polycarbonate membranes with 1 micron pore diameters. Each section was then gradually filled with a deionized water and Bristol solution recommended for microalgae growth. Phosphate and nitrate were added to Section A of the aquarium and allowed to diffuse throughout the tank. A water pump was used to …

The Effects Of Concentration, Stir Rate, And Processing Temperature On The Iridescence Of Polymethyl Methacrylate Nanoparticles, David Baruela

Materials Engineering

Synthetic opals were synthesized by creating polymethyl methacrylate (PMMA) nanospheres in order to determine which conditions would create the best iridescent samples. The factors affecting the iridescence were nanosphere concentration, stir rate, and processing temperature. PMMA solutions were made by adding 17 mg of granular azobis to a solution of 16 mL of distilled water with 3 mL of methyl methacrylate (MMA). The solution was stirred at different rates, slow and fast, and different temperatures, 70 °C and 90 °C, under a constant flow of nitrogen gas for 40 minutes until the polymerization reaction was complete. Glass substrates were prepared …

Improved Manufacturing Methods Of Bovine Femur Samples For Ultrasonic Testing And Assessment Of Materials Through Contract Angle Measurement, Kevin Mathew Lopez Galang

Biomedical Engineering

At California Polytechnic State University of San Luis Obispo (Cal Poly), the Biomedical Engineering department (BMED) requires its students to take the course listed as “BMED 420: Principles of Biomaterial Designs.” BMED 420 has a required laboratory section every week throughout the duration of the course that is meant to be a supplemental tool for learning. During the lab sections, students perform experiments and exercises that are currently being implemented in the industry. Despite accuracy of the methods and experiments relative to their use in the industry, there is always room for improvement. The objective of this project will illustrate …

Determining A Method For Rendering Low Cost Cdse(Zns) Core(Shell) Quantum Dots Aqueous Soluble Via Amphiphilic Polymer Wrapping, Patrick Mcbride

Materials Engineering

Herein is described the procedure of two amphiphilic polymer wrapping techniques that may be employed for obtaining aqueous soluble quantum dots (QDs) for use in biological fluorescent imaging applications. The advent of QDs has led to new nanoscale fluorescent materials that exhibit unparalleled quantum yields (QYs), high resistance to photobleaching, tunable emissions, and
absorption over a large optical range. However, the QD synthesis employed here at Cal Poly to obtain bright, photostable CdSe(ZnS) core(shell) QDs involves the use of organic solvents and surfactants, leading to hydrophobic QDs. Since all of biology relies on aqueous solubility, this hydrophobicity creates a major …

Artificial Muscle Project: Process Development Of Polydimethyl Siloxane Thin Films For Use In Dielectric Electroactive Polymer Artificial Muscle Actuators, Vincent J. Gayotin, Richard W. Morrison, Paul A. Preisser

Materials Engineering

An artificial muscle design was created founded on the principles of a dielectric electroactive polymer (DEAP), which is fundamentally similar to a capacitor. A polydimethyl siloxane (PDMS)-based elastomer, Sylgard 184 from Dow Corning, was chosen for the design and spun coat onto polystyrene (PS) Petri dishes at varying speeds to create a thin film, using speeds of 2000 rpm, 3000 rpm, 4000 rpm, 5000 rpm, and 6000 rpm. The film thicknesses were measured optically through use of a microscope with coupled computer imaging software to generate a characteristic curve of film thickness to spin speed, achieving a minimum film thickness …

Processing Pdms Gecko Tape Using Isopore Filters And Silicon Wafer Templates, Boris Luu

Materials Engineering

Gecko tape was processed through nanomolding involving two types of templates. One template was a Millapore Isopore polycarbonate membrane filter and the other template was an n-type silicon wafer processed to include four different pore diameters. These pore diameters were 20, 40, 80, and 160 microns. AutoCAD was used to design to a mask to be used later during photolithography. Two n-type wafers were sputtered with aluminum, underwent photolithography, and then etched using reactive ion etching. A template was placed into a Petri dish and Sylgard 184 polydimethylsiloxane (PDMS) was poured on the template. Once the PDMS cured,   the 1 …

Assessment Of Electrospinning As An In-House Fabrication Technique For Blood Vessel Mimic Cellular Scaffolding, Colby M. James

Master's Theses

Intravascular devices, such as stents, must be rigorously tested before they can be approved by the FDA. This includes bench top in vitro testing to determine biocompatibility, and animal model testing to ensure safety and efficacy. As an intermediate step, a blood vessel mimic (BVM) testing method has been developed that mimics the three dimensional structure of blood vessels using a perfusion bioreactor system, human derived endothelial cells, and a biocompatible polymer scaffold used to support growth of the blood vessel cells. The focus of this thesis was to find an in-house fabrication method capable of making cellular scaffolding for …

The Effect Of Particle Surface Area To Volume Ratio On Ion Release From Cocr Spheres, Darin J. Grandfield

Master's Theses

In 2005, over 200,000 Americans underwent a hip arthroplasty, the replacement of a hip joint with an artificial prosthesis. Of these arthroplasties, metal-on-metal type implants represent an increasing usage percentage. Metal-on-metal implants are selected largely for their low volumetric wear rate, durability, and resistance to corrosion. In spite of these advantages, little is known concerning the long-term consequences of heavy metal alloy use in the body, although early research indicates potentially carcinogenic results. This thesis is a preliminary investigation into these long term effects and their root causes.

An improved comprehension of the corrosion kinetics and the rate of ion …

Evaluating The Electrical Response Of Polyaniline To Mechanical Strain, Matthew L. Goebel

Master's Theses

This thesis focuses on the electrical output of polyaniline films subjected to uniaxial strain in hydrochloric acid solutions. Polyaniline belongs to novel class of materials known as conducting polymers. Alternating single and double bonds in the backbone of conducting polymers allow them to transmit electric charge when they are doped with negatively charged ions. Modifying the degree of doping and other electrical/chemical treatments allow conducting polymers to exhibit conducting, semi-conducting, or insulating electrical properties. Resilient mechanical properties, good processability, and low cost make conducting polymers good candidates for applications traditionally held by metals and semi-conductors.

When tensile strain is applied …