Biology and Biomimetic Materials Commons^™

Synthesis Of Zinc Oxide Nanorods And Use In Biosensor Applications, Anishkumar Manoharan

Graduate Theses and Dissertations

The main aim of this research was to develop a nanorod based biosensor for biomedical applications. In this project I use zinc oxide nanorods as the bio-material for biosensor. I fabricated these nanorods using a solution-based technique. Initially I coated a zinc oxide seed layer as the base. This seed layer was then annealed at 350 degrees for almost 1 hour. As a next step, interdigitated electrodes were fabricated on the top of the seed layer using a lift off process. The zinc oxide nanorods were then grown at 90 degrees for almost 4 hours along the electrodes. In this …

A Modified Surface On Titanium Deposited By A Blasting Process, Caroline O' Sullivan, Peter O'Hare, Greg Byrne, Liam O'Neill, Katie B. Ryan, Abina M. Crean

Publications

Abstract

: Hydroxyapatite (HA) coating of hard tissue implants is widely employed for its biocompatible and osteoconductive properties as well as its improved mechanical properties. Plasma technology is the principal deposition process for coating HA on bioactive metals for this application. However, thermal decomposition of HA can occur during the plasma deposition process, resulting in coating variability in terms of purity, uniformity and crystallinity, which can lead to implant failure caused by aseptic loosening. In this study, CoBlast™, a novel blasting process has been used to successfully modify a titanium (V) substrate with a HA treatment using a dopant/abrasive regime. …

Improved Manufacturing Methods Of Bovine Femur Samples For Ultrasonic Testing And Assessment Of Materials Through Contract Angle Measurement, Kevin Mathew Lopez Galang

Biomedical Engineering

At California Polytechnic State University of San Luis Obispo (Cal Poly), the Biomedical Engineering department (BMED) requires its students to take the course listed as “BMED 420: Principles of Biomaterial Designs.” BMED 420 has a required laboratory section every week throughout the duration of the course that is meant to be a supplemental tool for learning. During the lab sections, students perform experiments and exercises that are currently being implemented in the industry. Despite accuracy of the methods and experiments relative to their use in the industry, there is always room for improvement. The objective of this project will illustrate …

Determining A Method For Rendering Low Cost Cdse(Zns) Core(Shell) Quantum Dots Aqueous Soluble Via Amphiphilic Polymer Wrapping, Patrick Mcbride

Materials Engineering

Herein is described the procedure of two amphiphilic polymer wrapping techniques that may be employed for obtaining aqueous soluble quantum dots (QDs) for use in biological fluorescent imaging applications. The advent of QDs has led to new nanoscale fluorescent materials that exhibit unparalleled quantum yields (QYs), high resistance to photobleaching, tunable emissions, and
absorption over a large optical range. However, the QD synthesis employed here at Cal Poly to obtain bright, photostable CdSe(ZnS) core(shell) QDs involves the use of organic solvents and surfactants, leading to hydrophobic QDs. Since all of biology relies on aqueous solubility, this hydrophobicity creates a major …

Artificial Muscle Project: Process Development Of Polydimethyl Siloxane Thin Films For Use In Dielectric Electroactive Polymer Artificial Muscle Actuators, Vincent J. Gayotin, Richard W. Morrison, Paul A. Preisser

Materials Engineering

An artificial muscle design was created founded on the principles of a dielectric electroactive polymer (DEAP), which is fundamentally similar to a capacitor. A polydimethyl siloxane (PDMS)-based elastomer, Sylgard 184 from Dow Corning, was chosen for the design and spun coat onto polystyrene (PS) Petri dishes at varying speeds to create a thin film, using speeds of 2000 rpm, 3000 rpm, 4000 rpm, 5000 rpm, and 6000 rpm. The film thicknesses were measured optically through use of a microscope with coupled computer imaging software to generate a characteristic curve of film thickness to spin speed, achieving a minimum film thickness …

Processing Pdms Gecko Tape Using Isopore Filters And Silicon Wafer Templates, Boris Luu

Materials Engineering

Gecko tape was processed through nanomolding involving two types of templates. One template was a Millapore Isopore polycarbonate membrane filter and the other template was an n-type silicon wafer processed to include four different pore diameters. These pore diameters were 20, 40, 80, and 160 microns. AutoCAD was used to design to a mask to be used later during photolithography. Two n-type wafers were sputtered with aluminum, underwent photolithography, and then etched using reactive ion etching. A template was placed into a Petri dish and Sylgard 184 polydimethylsiloxane (PDMS) was poured on the template. Once the PDMS cured,   the 1 …

Characterization And Implementation Of Low Intensity Pulsed Ultrasound As A Tool To Apply Physical Load To Scaffolds And Bone Cells For Fracture Repair, Scott Frazee

Master's Theses

One current challenge in treating bone fractures is the effective treatment of non-unions and delayed unions. Low Intensity Pulsed Ultrasound (LIPUS) has been approved by the FDA to treat fresh fractures since 1994 and non-unions since 2000 and is an attractive treatment option because it is non-invasive. The mechanism by which it works, however, is not well understood; what is known is largely confined to the resultant changes in chemical output of cells. In this thesis several concepts and techniques were brought together to investigate the following hypothesis: LIPUS produces a measurable physical load that results in measurable deformation and …

Experimental Investigation Of Natural Fiber Reinforced Composite, Irene Samy Fahim

Theses and Dissertations

There is a growing use of polymers in different applications worldwide. This phenomenon resulted in an enormous increase in the amount of plastic waste. These wastes have significant impacts on the environment including pollution and depletion of resources. Recycling plastic waste and reusing it helps in alleviating environmental degradation. The amount of recycled plastics all over the world not utilized is huge. U.S.A recycled 5.7% of the total plastics generated and Western Europe recycled 39% of total amount of plastics consumed [1]. This research studies the potential usage of virgin and recycled polymer reinforced with natural fiber such as rice …