Transport Phenomena Commons^™

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Microbial Desalination Cells With Efficient Platinum Group Metal-Free Cathode Catalysts, Morteza Rezaei Talarposhti

Chemical and Biological Engineering ETDs

Iron-nitrogen-carbon based catalyst was used at the cathode of a microbial desalination cell (MDC) and compared with platinum (Pt) and activated carbon (AC) cathode. Fe-N-C catalyst was prepared using nicarbazin (NCB) as organic precursor by sacrificial support method (SSM). Rotating ring disk electrode (RRDE) experiments shows that Fe-NCB had higher electrocatalytic activity compared to AC and Pt. The utilization of Fe-NCB into the cathode improved substantially the performance output with initial maximum power density of 49±2 μWcm^-2 in contrast to Pt and AC catalysts which have shown lower values of 34±1 μWcm^-2 and 23.5±1.5 μWcm^-2, respectively. …

Modal Phonon Transport Across Interfaces By Non-Equilibrium Molecular Dynamics Simulation, Yang Zhong, Tianli Feng, Xiulin Ruan

The Summer Undergraduate Research Fellowship (SURF) Symposium

Phonons represent the quantization of lattice vibration, responsible for heat transfer in semiconductors and dielectrics. Phonon heat conduction across interfaces is crucially important for the thermal management of real-life devices such as smartphones, electric vehicles, and satellites. Although recent studies have broadly investigated spectral phonon contribution to lattice thermal conductivity, the mechanism of phonon modal transport across interfaces is still not well-understood. Previous models, including the acoustic mismatch model (AMM) and diffuse mismatch model (DMM), only consider elastic process while neglecting inelastic phonon contributions. Herein, we employ spectral Non-Equilibrium Molecular Dynamics Simulation (NEMD) to probe the temperature and heat flux …

Shear Driven Micro-Fluidic Pump For Cardiovascular Applications, Nihad E. Daidzic

Aviation Department Publications

A valveless shear-driven micro-fluidic pump design (SDMFP) for hemodynamic applications is presented in this work. One of the possible medical and biomedical applications is in-vivo hemodynamic (human blood circulation) support/assist. One or more SDMFPs can be inserted/implanted into vascular lumens in a form of a stent/duct in series and/or in parallel (bypass duct) to support blood circulation in-vivo. A comprehensive review of various micro-pump designs up to about mid 2000’s is given in [1,2]. Many of micropump designs considered are not suitable for in-vivo or even in-vitro medical/biomedical applications.

Operating principles, design, and SDMFP features are given in [3]. A …

Design And Evaluation Of 3d Printed Features To Improve Stability Of Plasma-Cell Pack Interface In Bacteria Separating Hollow Spinning Disk, Colin G. Bledsoe, Ryan L. Wood, Daneil S. Mcclellan, Dr. William G. Pitt

Biomedical Engineering Western Regional Conference

PDF submission of abstract.

Synthesis Of Copper Oxide Nanoparticles In Droplet Flow Reactors, Christopher Reilly

Honors Theses and Capstones

Synthesis of metal oxide nanoparticles within droplet flow reactors is advantageous over batch synthesis due to the elimination of concentration and temperature gradients inside the reactor and prevention of reactor fouling. We present results on the synthesis of copper oxide nanoparticles using aqueous droplets of copper acetate and acetic acid inside a bulk stream of sodium hydroxide in 1-octanol. Varying the copper acetate, acetic acid, and sodium hydroxide concentration resulted in needle-like and plate-like nanoparticles of varying sizes. The rate of mass transfer from the bulk to the droplet phase was found to increase with flow rate and addition of …

The Effects Of Carboxylic Acids In Aluminum Anodizing, Abby E. Koczera

Honors Theses and Capstones

Hard-anodized alumina coatings were formed in sulfuric acid at low temperature and high current density in the presence of carboxylic acid additives. Citric acid, trimesic acid, mellitic acid and ethylenediaminetetraacetic acid (EDTA) were utilized in varying concentrations. The additives were chosen for their capacity to form complexes with tri-valent aluminum and hence impart chemical stability to the coatings. The coatings were sealed in boiling water, and corrosion resistance was observed in a high pH solution of potassium hydroxide. The coatings were examined using scanning electron microscopy (SEM) to assess coating thickness and pore dimensions. Thicker coatings were produced when the …

Pore-Confined Carriers And Biomolecules In Mesoporous Silica For Biomimetic Separation And Targeting, Shanshan Zhou

Theses and Dissertations--Chemical and Materials Engineering

Selectively permeable biological membranes composed of lipophilic barriers inspire the design of biomimetic carrier-mediated membranes for aqueous solute separation. This work imparts selective permeability to lipid-filled pores of silica thin film composite membranes using carrier molecules that reside in the lipophilic self-assemblies. The lipids confined inside the pores of silica are proven to be a more effective barrier than bilayers formed on the porous surface through vesicle fusion, which is critical for quantifying the function of an immobilized carrier. The ability of a lipophilic carrier embedded in the lipid bilayer to reversibly bind the target solute and transport it through …

Numerical Simulation On The Combustion Characteristic Of Iron Ore Sintering With Flue Gas Recirculation, Gan Wang, Zhi Wen, Guofeng Lou, Ruifeng Dou, Xunliang Liu, Fuyong Su, Sizong Zhang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Influence Of Socio-Demography And Operating Streetscape On Last-Mile Mode Choice, M. Meng, P. P. Koh, Y. D. Wong

Journal of Public Transportation

This study investigated how personal and operational factors (travel distance and streetscape) influence traveler mode choice decisions for the last-mile home-bound trip stage from rail transit stations. Personal factors include the socio-demography of travelers, and attributes of the streetscape include the built environment (degree of areal development), prevalence of cycling, availability of short-range transport modes, and walking/cycling infrastructure. Interviewers randomly intercepted pedestrians to administer a mode choice survey at five rail transit station exits and engaged all available cyclists at bicycle parking areas in the vicinity of stations in Singapore. A multimodal logit regression model revealed a significant relationship between …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Model Validation And Transition To Turbulence In Orbiting Culture Dishes., Jonathan Michael D. Thomas

Electronic Theses and Dissertations

Wall shear stress (WSS) is commonly accepted as the primary influence affecting characteristics of anchored endothelial cells when subjected to fluid flow. Orbital shakers are commonly used to study cellular responses due to their ease of use, ability to run several experiments simultaneously, and since they exert physiologically relevant oscillatory shear. These studies require comprehensive resolution of WSS, however the fluid dynamics inside orbiting culture dishes has not yet been well described since the flow is complex and difficult to quantify analytically. A computational fluid dynamics (CFD) model of flow in an orbiting dish has been developed that yields detailed …

Investigation Of A Nanoparticle Delivery System For Micronutrients In Corn, Zully Perez Sierra, Zachary P. Stewart, Hendrik J. Viljoen

UCARE: Research Products

Pheroid Nanoparticle Delivery System1 • Cost effective for plant applications • Safe – multi-lamellar lipid system derived mostly from soybeans • Versatile – payloads delivered range from micronutrients to antibiotics Micronutrient Deficiency • Caused by the immobility of micronutrients through the plant. • Leads to malnutrition children in poor countries2 • As fertilizers deliver nutrients, only small percentage obtained by plant. Purpose of Nanoparticle Delivery System • Increase plant micronutrient content and yield • Reduces the effects of run-of, overuse and pollution Other Nano-Fertilizer Trials • Desert plant results – in a foliar application versus irrigation application, the foliar nano-fertilizer …

Effect Of Spalled Particles Thermal Degradation On A Hypersonic Flow Field Environment, Raghava S. C. Davuluri, Huaibao Zhang, Alexandre Martin

Mechanical Engineering Faculty Publications

Two-way coupling is performed between a spallation code and a hypersonic aerothermodynamics CFD solver to evaluate the effect of spalled particles on the flow field. Time accurate solutions are computed in argon and air flow fields. A single particle simulations and multiple particles simulations are performed and studied. The results show that the carbon vapor released by spalled particles tend to change the composition of the flow field, particularly the upstream region of the shock.

High-Temperature, High-Pressure Viscosities And Densities Of Toluene, Aaron J. Rowane

Theses and Dissertations

High-temperature, high-pressure (HTHP) conditions are exemplified in ultra-deep petroleum reservoirs and can be exhibited within diesel engines. Accurate pure component hydrocarbon data is essential in understanding the overall behavior of petroleum and diesel fuel at these conditions. The present study focuses on the HTHP properties of toluene since this hydrocarbon is frequently used to increase the octane rating of gasoline and toluene occurs naturally in crude oil. In this thesis experimental densities and viscosity are presented to 535 K and 300 MPa extending the database of toluene viscosity data to higher temperature than previous studies. The data is correlated to …

Calcium Alginate Microbead Production Via An Air Assisted Shearing Process, Ryan Loftus

Williams Honors College, Honors Research Projects

The purpose of this project was to model the size of calcium alginate microbeads produced by extruding a solution of 1.5 wt.% alginate from a syringe and needle with air shear generated from a pneumatic line flowing in an annular tube around the extrusion needle. The air shear would create microdroplets that would fall into a solution of 2 wt.% calcium chloride in water, crosslinking the droplets into beads. These microbeads can be used in drug dispersion applications or in encapsulation of cells throughout the body due to their biocompatibility. The goal was to create uniform beads that ranged from …

Elevated Test Pressure Significantly Reduces Dynamic Accumulation Oxygen Transmission Rate (Astm F3136) Measurement Time For Barrier Packaging Films, Bruce A. Welt

Journal of Applied Packaging Research

Measurement of gas transmission rates of materials is important for successful package design. The dynamic accumulation (DA) method (ASTM F3136) is becoming increasingly popular for measuring oxygen transmission rate (OTR) due to its simplicity and low cost. However, measurement time increases with barrier properties of materials, limiting measurement throughput. A dynamic accumulation measurement prototype capable of operating up to 1,000 psig was developed in order to accelerate gas transfer by boosting concentration gradients via elevated absolute pressures. Results show that measurement results were independent of test pressure while measurement times were substantially reduced. These results also suggest that gas transmission …

A Computational Study Of The Potential For Lng Tanker Polystyrene Foam Insulation Failure Under Fire Exposure, Jeffrey David Martinez

Graduate Theses and Dissertations

Liquefied natural gas is shipped across the oceans in large marine carriers. The carriers house the LNG using several different insulation systems. One of these systems involves large aluminum spheres insulated with polystyrene foam. Polystyrene foam is very susceptible to heat degradation. This raised issues as to the extent of possible insulation failure caused by a large ship fire. Experiments were done investigating the nature of polystyrene’s thermal degradation, notably by Brauman, Chen, and Matzinger and Butler. A large scale investigation was also performed by Sandia National Laboratory. However, computational modeling of the degradation was lacking. This work set out …

Coalescence-Induced Jumping Of Droplet: Inertia And Viscosity Effects, Samaneh Farokhirad, Jeffrey F. Morris, Taehun Lee

Publications and Research

The problem of coalescence-induced self-propelled jumping of droplet is studied using three-dimensional numerical simulation. The focus is on the effect of inertia and in particular the effect of air density on the behavior of the merged droplet during jumping. A lattice Boltzmann method is used for two identical, static micro-droplets coalescing on a homogeneous substrate with contact angle ranging from 0◦ to 180◦. The results reveal that the effect of air density is significant on detachment of the merged droplet from the substrate at the later stage of the jumping process; the larger the air density, the larger the jumping …

Approximate Analytical Solution For The Isothermal Lane-Emden Equation In A Spherical Geometry, Moustafa A. Soliman, Yousef S. Al-Zeghayer

Chemical Engineering

This paper obtains an approximate analytical solution for the isothermal Lane-Emden equation that models a self-gravitating isothermal sphere. The approximate solution is obtained by perturbation methods in terms of small and large distance parameters. The approximate solution is compared with the numerical solution. The approximate solution obtained is valid for all values of the distance parameter.

Low Molecular Weight Glucosamine/L-Lactide Copolymers As Potential Carriers For The Development Of A Sustained Rifampicin Release System: Mycobacterium Smegmatis As A Tuberculosis Model, Jorge Ragusa

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

Tuberculosis, a highly contagious disease, ranks as the second leading cause of death from an infectious disease, and remains a major global health problem. In 2013, 9 million new cases were diagnosed and 1.5 million people died worldwide from tuberculosis. This dissertation aims at developing a new, ultrafine particle-based efficient antibiotic delivery system for the treatment of tuberculosis. The carrier material to make the rifampicin (RIF)-loaded particles is a low molecular weight star-shaped polymer produced from glucosamine (molecular core building unit) and L-lactide (GluN-LLA). Stable particles with a very high 50% drug loading capacity were made via electrohydrodynamic atomization. Prolonged …

Flow Regime Transition In Trickle Bed Reactors, Eric P. Lehmann, Gregory Honda, Arvind Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

In industry, trickle bed reactors – fixed beds in which gas and liquid reactants flow concurrently downward through catalyst - are often operated at gas and liquid superficial velocities near the transition boundaries between flow regimes, especially the transition between trickle to pulse flow. Previous studies have characterized flow regime transitions as sharp transitions that occur at single superficial liquid velocities for a fixed superficial gas velocity. In reality, transitions evolve gradually over a range of superficial liquid velocities. Experiments were conducted in a fixed bed with air and water flowing concurrently downward using two different packing media. The transitions …

A Soft Condensed Matter Approach Towards Mathematical Modelling Of Mass Transport And Swelling In Food Grains, Michael Chapwanya, N. Misra

Articles

Soft condensed matter (SCM) physics has recently gained importance for a large class of engineering materials. The treatment of food materials from a soft matter perspective, however, is only at the surface and is gaining importance for understanding the complex phenomena and structure of foods. In this work, we present a theoretical treatment of navy beans from a SCM perspective to describe the hydration kinetics. We solve the transport equations within a porous matrix and employ the Flory–Huggin’s equation for polymer–solvent mixture to balance the osmotic pressure. The swelling of the legume seed is modelled as a moving boundary with …

Optimizing Polymer Fluorescence For Explosives Detection, Rose K. Cersonsky

Honors Scholar Theses

Pyrene is commonly used for explosives detection, as when mixed with polystyrene, the fluorescence intensity of the resulting film can be used as an indicator of the presence of nitro-aromatic, nitro-ether, or nitro-amine explosives. Previous studieshave tested a three-component system including pyrene, polystyrene, and a salt, tetrabutylammonium hexafluorophosphate (TBAHP). From these previous studies, it has been seen that vapor pressure of the preparation area is a governing factor in the formation of excimers, which are instrumental in achieving and maintaining fluorescence intensity. In this study, three parameters – solution concentration, film thickness, and molecular weight of polystyrene are examined to …

Model-Based Energy Analysis Of An Integrated Midrex-Based Iron/Steel Plant, Abdelhamid M. Ajbar, Khalid I. Alhumaizi, Moustafa A. Soliman, Emadadeen Ali

Chemical Engineering

This article presents modeling and simulations of an integrated plant for the production of steel using the direct reduced iron (DRI)=electric arc furnace (EAF) route. In a previous work (Alhumaizi et al., 2012), a comprehensive mathematical model of an iron plant based on MIDREX technology was developed, validated, and simulated. In this article, the model is extended to account for an empirical model of an EAF plant. Numerical simulations were carried out for the effect of different operating parameters of the integrated plant. Useful profiles as well as a summary table were compiled to illustrate the results of the sensitivity …

Quantification Of Factors Governing Drug Release Kinetics From Nanoparticles: A Combined Experimental And Mechanistic Modeling Approach, Kyle Daniel Fugit

Theses and Dissertations--Pharmacy

Advancements in nanoparticle drug delivery of anticancer agents require mathematical models capable of predicting in vivo formulation performance from in vitro characterization studies. Such models must identify and incorporate the physicochemical properties of the therapeutic agent and nanoparticle driving in vivo drug release. This work identifies these factors for two nanoparticle formulations of anticancer agents using an approach which develops mechanistic mathematical models in conjunction with experimental studies.

A non-sink ultrafiltration method was developed to monitor liposomal release kinetics of the anticancer agent topotecan. Mathematical modeling allowed simultaneous determination of drug permeability and interfacial binding to the bilayer from release …

Ultrasound Assisted Hydration Of Navy Beans (Phaseolus Vulgaris), N. Misra

Articles

The use of ultrasound to enhance the transport phenomena in food processes has been well recognised in recent times. The objective of this study was to evaluate the effect of sonication on hydration rate and pasting profile of navy beans. The hydration kinetics for control and ultrasound assisted soaking was mathematically described using mechanistic (Fickian diffusion) and empirical (Peleg’s equation, Weibull model and First Order equation) models. Ultrasound enhanced the rate of hydration which was evident from the plot of kinetic data and model parameters. The effective diffusivities for water transport without and with ultrasound application were estimated to be …

Approximations To The Solution Of The Frank-Kamenetskii Equation In A Spherical Geometry, Moustafa A. Soliman

Chemical Engineering

In this paper, an approximate analytical solution for Frank-Kamenetskii equation modeling a thermal explosion in a sphere, is obtained. The approximate solution is obtained by perturbation methods in terms of small and large distance parameter. The approximate solution is compared with the numerical solution obtained from an initial value problem formulation to the original boundary value problem. The approximate solution obtained is valid for all values of the distance parameter. For the original boundary value problem and for a given Frank-Kamenetskii parameter, a nonlinear algebraic equation needs to be solved to be able to apply the approximate solution.

Nanofiltration Membranes From Oriented Mesoporous Silica Thin Films, Mary K. Wooten

Theses and Dissertations--Chemical and Materials Engineering

The synthesis of mesoporous silica thin films using surfactant templating typically leads to an inaccessible pore orientation, making these films not suitable for membrane applications. Recent advances in thin film synthesis provide for the alignment of hexagonal pores in a direction orthogonal to the surface when templated on chemically neutral surfaces. In this work, orthogonal thin film silica membranes are synthesized on alumina supports using block copolymer poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) (P123) as the template. The orthogonal pore structure is achieved by sandwiching membranes between two chemically neutral surfaces, resulting in 90 nm thick films. Solvent flux of ethanol through …

Generation Of Multicomponent Polymer Blend Microparticles Using Droplet Evaporation Technique And Modeling Evaporation Of Binary Droplet Containing Non-Volatile Solute, Venkat N. Rajagopalan

Theses and Dissertations--Chemical and Materials Engineering

Recently, considerable attention has been focused on the generation of nano- and micrometer scale multicomponent polymer particles with specifically tailored mechanical, electrical and optical properties. As only a few polymer-polymer pairs are miscible, the set of multicomponent polymer systems achievable by conventional methods, such as melt blending, is severely limited in property ranges. Therefore, researchers have been evaluating synthesis methods that can arbitrarily blend immiscible solvent pairs, thus expanding the range of properties that are practical. The generation of blended microparticles by evaporating a co-solvent from aerosol droplets containing two dissolved immiscible polymers in solution seems likely to exhibit a …