Transport Phenomena Commons^™

Amine-Functionalized Lignin-Based Ionomer Nanocomposites For Redox Flow Batteries, Joshua Wilder

All Theses

As the development of energy storage technologies for renewable energy sources continues to garner attention, vanadium redox flow batteries (VRFBs) have emerged as promising source for grid-scale energy storage. A major component of the VRFB is the ion exchange membrane (IEM), as it serves to physically separate the two liquid electrolytes and also directly impacts the battery’s capacity, efficiency, and cost. The current industry standard IEM, Nafion™, not only accounts for a large portion of the cost of the VRFB but also suffers from poor proton selectivity. Herein, we have synthesized sulfonated poly(ether ether ketone) (SPEEK) composite membranes containing amine …

Computational Modeling Using A Novel Continuum Approach Coupled With Pathway-Informed Neural Networks To Optimize Dynein-Mediated Centrosome Positioning In Polarized Cells, Arkaprovo Ghosal, Padmanabhan Seshaiyar Dr., Adriana Dawes Dr., General Genomics Inc.

Annual Symposium on Biomathematics and Ecology Education and Research

No abstract provided.

Hydrodynamic Voltammetry Of Fe2+/3+ In Aqueous Deep Eutectic Solvents Towards Redox Flow Batteries, Desiree Mae Prado, Xiaochen Shen, Robert Savinell, Clemens Burda

Faculty Scholarship

Deep eutectic solvents (DESs) have recently attracted much attention as potential green electrolyte solvents for redox flow batteries. DESs are considered not only as environmentally sustainable but also economically attractive electrolytes because they can be resourced from biological feedstock (alcohols, urea, choline) and are earth-abundant and of low toxicity. Despite these advantages, DESs still have limitations in important aspects such as reactant and ion transport, which is inhibited due to hydrogen-bonding-induced viscosity. Thus, improving the transport properties of redox species in DESs is essential. In addition, we explore the quantitative addition of water to ethaline (a 1:2 choline chloride: ethylene …

Effects Of Alternative Jet Fuels On Aerospace-Grade Composites: Experimental And Modeling Studies, Naoufal Harich

Theses and Dissertations

The aviation industry aims to reduce its environmental impact through innovation and research. The usage of composite materials for multiple primary structures represents one such measure. Several alternative fuels were approved and used along with the Federal Aviation Administration (FAA). These alternative fuels are produced from wastes and biomasses. Some alternative fuels were initially only approved as drop-in fuels, meaning they must be blended with conventional fuels to operate. Fuel tanks are usually embedded into the wing structure, which is mainly made of composite materials. These composites tend to absorb fluids it encounters through their matrix phase. The absorption behavior …

Development Of Novel Sensor Coating Methodology To Enable Understanding Of Fouling Mechanisms On Ion Exchange Membranes, Andrew Ulmer

Honors Theses

As populations expand and natural water resources are depleted, severe droughts and limited access to clean water have become an increased threat to areas across the world. Effective and economic water treatment methods such as electrodialysis (ED) are vital for combating these threats, especially in developing nations and secluded locations. Organic foulant adsorption on the surface of ion exchange membranes severely limits the capabilities of water desalination systems such as ED along with significantly increasing maintenance costs. Understanding characteristics such as the total amount and rate at which these foulants at specific concentrations adsorb and desorb to the membranes is …

Measuring Plume Concentration Variations Under Neutral Atmospheric Conditions, Daniel Williams

Chemical Engineering Undergraduate Honors Theses

Hazardous gases are increasingly becoming a large safety concern as the world continues to grow and industrialize. The modeling of when hazardous gases breach containment is an extremely important objective of consequence assessment planning and response. To improve the understanding of the variability inherent in passive gas releases, a test program to demonstrate the variability of gas concentration measurements at different location in a passive gas plume released from an area source in the ultra-low speed wind tunnel at the Chemical Hazards Research Center. A Flame Ionization Detector was used to measure the concentration of the source cloud. Methane was …

Heat Transfer From Plates, Leanza Trevino

Chemical Engineering Undergraduate Honors Theses

The purpose of this honors thesis is to create an experiment for the CHEG Lab I course. This is a continuation of work done by Alexa Moreno. She created an experiment to model free convection of a horizontal plate. In this report, free and forced convection of a vertical and horizontal plate, respectively are modeled. This report explains the motivation for creating this heat convection experiment, the results of performing the experiment, and provides recommendations for future work on this experiment. Lab handouts are included in the Appendix.

Utilization Of Electrodeionization To Separate And Concentrate Cellobionic And Gluconic Acid, Andie Veeder

Chemical Engineering Undergraduate Honors Theses

Biofuel production is currently an expensive and inefficient process with many drawbacks. It is water and land intensive, competes with food production, and requires large energy inputs decreasing its relative sustainability. This paper explores the use of electrodeionization (EDI) to improve the biofuel process by separating and concentrating large, organic sugar acids that are important materials for the production of bioethanol. An EDI device was assembled for the purpose of separating and concentrating gluconic, cellobionic and lactobionic acid. Several trials were conducted and samples were analyzed to determine the success of this experiment. The results for the separation and concentration …

Characterizing And Quantifying Shear-Induced Hemolysis In A Hollow Fiber Membrane System, Siddhi Bhat

Chemical Engineering Undergraduate Honors Theses

Clinical studies have shown that patients undergoing renal replacement therapy are more susceptible to developing hemolysis, or the rupturing of red blood cells. Rapid hemolysis can cause symptoms such as anorexia, vomiting, and even death in severe cases. The aim of this study is to identify how shear stress within a hollow fiber membrane impacts the level of hemolysis that occurs. This allows for the optimization of the ultrafiltration membranes that are typically used for hemofiltration treatments. The variables being studied are the radii of hollow fibers, number of fibers, and volumetric flow rate of blood being circulated. Here, we …

Separation Of Organic Acids Through Direct Catalysis From Sugars, Katelyn Robinson

Chemical Engineering Undergraduate Honors Theses

Society relies on plastic products, whether they are single use or durable. A downside of plastic is that the most common type is a product of oil and oil is not only a limited resource but also a climate-damaging resource. Polylactic acid (PLA) is a bio-based, biodegradable plastic. However, the process of converting biomass to polylactic acid polymer has the largest environmental impact of the PLA production process, so alternative methods of conversion are needed (Moretti et al., 2021). The polylactic acid polymer can be made with lactic acid, which can be converted from glucose.

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Elucidating The Mechanical And Transport Properties Of Lignin-Based Hydrogel Composites, Nicholas Gregorich

All Dissertations

The use of lignin in the fabrication of soft composites has become an emerging area of research in polymer science and polymer chemistry. These lignin-based materials present numerous benefits, notably, a reduction in the use of petroleum-based precursor, improved structural benefits to otherwise soft host polymers, as well as the inherent antimicrobial and antioxidant properties of lignin, making it suitable for biomaterials. Herein, we present two chemical reaction pathways of incorporating lignin that was fractionated and cleaned using the Aqueous Lignin Purification with Hot Agents (ALPHA) process into poly(vinyl alcohol) (PVA) hydrogel composites for aqueous-based separations. By leveraging the ALPHA …

Removal Of Hexavalent Chromium From Water By Chitosan-Enhanced Ultrafiltration, Putu A. Y. Indiasih, Anindita D. Syaifudin, Nurul Faiqotul Himma, Bambang Ismuyanto

Makara Journal of Technology

Polymer-enhanced ultrafiltration has gained increasing attention as a selective separation process to remove small solutes, such as metal ions, from water or wastewater. Hexavalent chromium Cr(VI) is one of the metal ions in wastewater that has received considerable attention because of its toxicity. Chitosan was used in this study as the polymer to bind Cr(VI) to enhance its removal by ultrafiltration. The effects of chitosan-to-Cr(VI) ratio on Cr(VI) rejection and permeate flux were investigated. In addition, the fouling tendency was evaluated. Results showed that the addition of chitosan with a mass ratio of 12.5 increased the Cr (VI) rejection from …

Application Of Pinch Analysis For Energy Saving And Reducing Gas Emissions Based On Mathematical Model In The Hydrocracking Unit, Badiea S. Babaqi

Hadhramout University Journal of Natural & Applied Sciences

Pinch analysis approach of the heat exchanger network in the hydrocracking unit was carried out to save the energy consumption and reduce the gas emissions simultaneously. This method based on mathematical model of the hydrocracking unit for a heat exchanger network using LINGO program to achieve the minimization of environmental impacts and the reduction of energy cost. The presented energy demands for the heat exchanger network are 20.38 MMBtu/hr and 26.52 MMBtu/hr for heating and cooling loads, respectively. The current analysis shows a huge opportunity in order to decrease energy consumption of the hydrocracking process at a minimum temperature difference …

Using Computational Fluid Dynamics And Optical Sensor Technology To Scale Cell Culture Platforms, Mandar Makwana

KGI Theses and Dissertations

Different cell culture vessels ranging from micro scale to laboratory scale to commercial scale play critical role in upstream process development for biologics manufacturing. Based on the mode of operation, cell culture vessels have different hydrodynamic environments, making it challenging to scale. Integrated approaches using computational tools supported by experimental studies can overcome these challenges. Computational Fluid Dynamics (CFD) is one such tool that can simulate hydrodynamics within the cell culture vessels and can provide insights at macro and micro-scale. Accuracy of a CFD model significantly depends on the fluid model and assumptions. Traditionally, simple two-equation fluid models were developed …

Effects Of Confinement On Ionic Liquids And Deep Eutectic Solvents For The Design Of Catalytic Systems, Electrochemical Devices, And Separations, Andrew Drake

Theses and Dissertations--Chemical and Materials Engineering

Confinement of ionic liquids (ILs) and deep eutectic solvents (DESs) within mesoporous materials such as silica helps to control the local environment within the pores for applications such as catalysis, electrochemistry, and absorption. Silica thin films with 2.5 and 8 nm pores and micron-sized silica particles with pore diameters of 5.4 and 9 nm were synthesized to study the effect of nanoconfinement on ILs 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF₆]), 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]), and DESs reline and ethaline (choline chloride and urea or ethylene glycol). Silica thin films with vertically aligned, well ordered, and accessible pores were synthesized via the evaporation-induced …

Attrition Study Of Copper-Supplemented Iron-Based Oxygen Carrier For Chemical Looping Combustion, Neng Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Chemical looping combustion (CLC) is a promising technology that can mitigate the carbon emissions for power generation. The cost of oxygen carriers (OCs) impedes the scale up of CLC. Compared to synthetic iron-based OCs, red mud (RM), an abundant iron-based solid waste from industry, is a cost-effective choice due to its intrinsic inclusion of both inert and catalytic phases that are crucial for CLC. It was anticipated that the addition of copper oxide to RM using a mechanical mixing method that can be easily scaled up would enhance both reactivity and oxygen transport capacity (OTC), and the heat of reaction …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Temperature-Dependent Diffusion In Block Copolymer Organogels, Ridwana Bashar

Master’s Theses

Organogels are often considered for transport-based applications such as transdermal drug delivery vehicles and gel actuators due to their unique properties. Recent consideration of styrenic block copolymer based organogels’ application in transdermal drug delivery requires an extensive investigation of drug diffusion behavior through these gels to assess their applicability. Temperature is a major influencing parameter on diffusion. The goal of this research is to better understand the impact of temperature on diffusion in styrenic triblock copolymer organogels. To accomplish this goal, we focused on three specific objectives: (i) accurately measure the diffusivities of a solute – AOT reverse micelles – …

Hydro Cyclonic Separation Of Polyester Microfibers From Washing Machine Wastewater, Joe Kulkarni

Dissertations, Master's Theses and Master's Reports

Clothing made from synthetic materials shed fibers in washing machines, and these fibers find their way into the effluent water. These fibers can absorb toxic materials in wastewater treatment plants and can then carry these toxins into other aquatic environments.

It’s believed that a hydro cyclone could be scaled down enough to fit into a washing machine and could be used to filter out up to 80% of the microparticles from the effluent water. It’s proposed to investigate if a hydro cyclone can be used for this application. The overall goal was for the hydro cyclone to concentrate the micro …

Techno-Economic Analysis And Optimization Of Hydrogen And Mechanical Energy Storage Systems, Pavitra Senthamilselvan Sengalani

Graduate Theses, Dissertations, and Problem Reports (ETD)

The increasing significance of renewable energy sources is thrusting the load cycling of fossil-fueled power plants (FFPP), designed to operate under nominal-load conditions. Integration of energy storage systems (ESS) with the FFPPs such as hydrogen energy storage (HES) and mechanical energy storage facility such as compressed air energy storage (CAES) shows the potential to minimize the levelized cost of electricity during high demand scenarios and also minimize the negative impacts of off-design FFPP operation. The deployment of energy storage facilities at the FFPP level have considerable potential advantages as they can be exploited within the existing equipment items and facilities …

The Effect Of Different Fracturing Fluids On The Productivity Of Multi-Staged Fractured Marcellus Shale Horizontal Wells, Vida Gyaubea Matey-Korley

Graduate Theses, Dissertations, and Problem Reports (ETD)

While hydraulic fracturing has undeniably improved the production from oil and gas reservoirs, this technology is not without limitations. The primary hurdles lie in the areas of proppant transport, fluid rheology, and stress management. Despite the extensive research conducted in this domain, there remains a considerable amount of work to be done for comprehensive solutions that account for the complex interactions among fracturing fluid, proppant distribution, and geomechanical conditions. Achieving this will then make room for a holistic and efficient hydraulic fracturing strategy.

This study addresses the above-mentioned problem by examining the impact of fluid type on proppant transport and …

Molecular Understanding Of Zwitterions And Quantum Computing For Sustainability, Manh Tien Nguyen

Theses and Dissertations--Chemical and Materials Engineering

The sustainable development of society needs sustainable energy solutions and the mitigation of greenhouse gas emissions. One key subject in this area is the development of safe and efficient ion-based batteries. Moreover, CO₂ capture is a crucial pathway in mitigating emissions from the combustion of fossil fuels. Ongoing efforts are to improve both technologies' safety and efficiency. This thesis presents our efforts to conduct computational research on understanding advanced zwitterionic electrolytes and CO₂ capture. Chapters 2-4 illustrate the computational research to understand ionic solvation in zwitterionic electrolytes. Solid-state electrolytes are essential for safer batteries. While solid polymer electrolytes …

Mechanisms Of Emulsion Destabilization: An Investigation Of Surfactant, Stabilizer, And Detergent Based Formulations Using Diffusing Wave Spectroscopy, Jordan N. Nowaczyk

Theses and Dissertations

Conventional approaches for studying emulsions, such as microscopy and macroscopic phase tracking, present challenges when it comes to establishing detailed mechanistic descriptions of the impact of emulsifier and stabilizer additives. Additionally, while a combination of sizing methods and macroscopic phase tracking can provide insights into droplet size changes and concentration, the use of multiple measurements can be cumbersome and error-prone. It is the focus of this work, to present a new method for studying water in oil (W/O) emulsions that involves using diffusing wave spectroscopy (DWS) to examine the impact of three different surface stabilizing additives at varying concentrations. By …