Biochemical and Biomolecular Engineering Commons^™

The Effect Of Tantalum Incorporation On The Physical And Chemical Properties Of Ternary Silicon–Calcium–Phosphorous Mesoporous Bioactive Glasses, Andrew Mendonca, Md Saidur Rahman, Adel Alhalawani, Omar Rodriguez, Reid C. Gallant, Heyu Ni, Owen M. Clarkin, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Synthesis and characterization of the first mesoporous bioactive glasses (MBGs) containing tantalum are reported here, along with their potential application as hemostats. Silica MBGs were synthesized using with the molar composition of (80-x)% Si, 15% Ca, 5% P, and x% Ta. It was found that incorporation of >1 mol % Ta into the MBGs changes their physical and chemical properties. Increasing Ta content from 0 to 10 mol % causes a decrease in the surface area and pore volume of ~20 and ~35%, respectively. This is due to the increase in nonbridging oxygens and mismatch of thermal expansion coefficient which …

Sequencing Heparan Sulfate Using Hilic Lc-Netd-Ms/Ms, Jiandong Wu, Juan Wei, Pradeep Chopra, Geert Jan Boons, Cheng Lin, Joseph Zaia

Chemical and Biochemical Engineering Faculty Research & Creative Works

Heparan Sulfate (HS) Mediates a Wide Range of Protein Binding Interactions Key to Normal and Pathological Physiology. Though Liquid Chromatography Coupled with Mass Spectrometry (LC-MS) based Disaccharide Composition Analysis is Able to Profile Changes in HS Composition, the Heterogeneity of Modifications and the Labile Sulfate Group Present Major Challenges for Liquid Chromatography Tandem Mass Spectrometry (LC-MS/MS) Sequencing of the HS Oligosaccharides that Represent Protein Binding Determinants. Here, We Report Online LC-MS/MS Sequencing of HS Oligosaccharides using Hydrophilic Interaction Liquid Chromatography (HILIC) and Negative Electron Transfer Dissociation (NETD). a Series of Synthetic HS Oligosaccharides Varying in Chain Length (Tetramers and Hexamers), …

Measurement Of Adhesion Of Sternal Wires To A Novel Bioactive Glass-Based Adhesive, Varinder Pal Singh Sidhu, Mark R. Towler, Marcello Papini

Chemical and Biochemical Engineering Faculty Research & Creative Works

Stainless steel wires are the standard method for sternal closure because of their strength and rigidity, the simplicity of the process, and the short healing time that results from their application. Despite this, problems still exist with sternal stability due to micromotion between the two halves of the dissected and wired sternum. Recently, a novel glass-based adhesive was developed which, in cadaveric trials and in conjunction with wiring, was shown to restrict this micromotion. However, in order to avoid complications during resternotomy, the adhesive should adhere only to the bone and not the sternal wire. In this study, sternal wires …

Renal Specific Rnai Delivery By Fibrillar Nanoparticle Excipients, Sam Wong

Dissertations, Theses, and Capstone Projects

RNA interference (RNAi) is a powerful tool to manipulate the phenotype of an organism by silencing the expression of specific genes and is viewed as a highly promising platform for treating undruggable targets and disorders where small molecule drugs and antibodies would fail. However, development of RNAi based therapies has faced major barriers including cellular and tissue-specific uptake of the Small Interfering RNA (siRNA). Utilizing different nanoparticles as RNAi excipients, cellular uptake and gene silencing potency can be greatly improved. The research in Dr. McDevitt groups has fibrillar carbon nanotubes (CNT) as carriers for siRNA for gene silencing in vitro …

Bioactive Glass Fiber Fabrication Via A Combination Of Sol-Gel Process With Electro-Spinning Technique, Malvika Nagrath, Adel Alhalawani, Alireza Rahimnejad Yazdi, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Bioengineering Extracellular Matrix Scaffolds For Volumetric Muscle Loss, Kevin Roberts

Graduate Theses and Dissertations

Volumetric muscle loss overwhelms skeletal muscle’s ordinarily capable regenerative machinery, resulting in fibrosis and severe functional deficits which have defied clinical repair strategies. My work spans the design and preclinical evaluation of implants intended to drive the cell community of injured muscle toward a regenerative state, as well as the development of an understanding of the molecular responses of this cell community to biomaterial interventions. I demonstrate a new class of biomaterial by leveraging the productive capacity of sacrificial hollow fiber membrane cell culture; I show specifically that unique threads of whole extracellular matrix can be isolated by solvent degradation …

The Statistics Of Directed Evolution: From Library Generation To High Throughput Screens, Keith Tyo

Biochemical and Molecular Engineering XXI

Directed evolution has been recognized as a powerful approach to creating enzymes and cells with desirable properties, such as growth on a new substrate, thermotolerance, or even novel reaction mechanisms. The directed evolution approach is to generate diversity through genetic mutations and screen the diversity for mutants that have improved properties compared to the parent. This diversification and screening can be repeated to generate mutants with superior properties.

While the concept is straightforward, the devil is in the details. How should I create diversity (error prone PCR, mutagenic primers, transposons…)? How much diversity do I need (10³, 10 …

K-Fit: Parameterizing Kinetic Models Of Metabolism Using Multiple Fluxomic Datasets, Costa Maranas

Biochemical and Molecular Engineering XXI

Kinetic models predict the metabolic flows by directly linking metabolite concentrations and enzyme levels to reaction fluxes. Robust parameterization of organism-level kinetic models that faithfully reproduce the effect of different genetic or environmental perturbations remains an open challenge due to the intractability of existing algorithms. This paper introduces K-FIT, an accelerated kinetic parameterization workflow that leverages a novel decomposition approach to identify steady-state fluxes in response to genetic perturbations followed by a gradient-based update of kinetic parameters until predictions simultaneously agree with the fluxomic data in all perturbed metabolic networks. The applicability of K-FIT to large-scale models is demonstrated by …

Biologicalisation: A Nature-Based Digital Manufacturing Revolution, William Whitford

Biochemical and Molecular Engineering XXI

Industry 4.0 is changing our manufacturing concepts [1]. Biologicalisation is the use of 4.0 principals in concert with biological and bio-inspired materials, chemistries and functions to support an efficient and sustainable manufacturing schema. From product design, to development and manufacturing, biomimetic product designs and bio-integrated manufacturing systems describe this biological transformation of manufacturing [2].

Please click Additional Files below to see the full abstract.

Advanced Technologies And Computational Modeling In Continuous Bioprocessing Heather Brooke, Pall Corporation, Usa, Heather Brooke, Edita Botonjic-Sehic

Biochemical and Molecular Engineering XXI

Biotech companies have been emphasizing the implementation and utilization of process analytical technology (PAT) and chemometrics in biomanufacturing. Advanced technologies and computation modeling have contributed significantly in making this capability come to life. Although there are still gaps in the area of advanced analytics for the process, computation modeling has started to contribute towards process characterization, which will lead to real-time process control. PAT and modeling infrastructure can be utilized in integrated continuous bioprocessing to gain better process understating, reduce production cycle time, improve yield, advance efficiency by converting from a batch process into a continuous process, and reduce cost …

Conference Program, Christina Chan, Mattheos Koffas, Steffen Schaffer, Rashmi Kshirsagar

Biochemical and Molecular Engineering XXI

No abstract provided.

Beneficial Reuse Of Industrial Co2 Emissions Using A Microalgae Photobioreactor: Waste Heat Utilization Assessment, Daniel T. Mohler, Michael H. Wilson, Zhen Fan, John G. Groppo, Mark Crocker

Center for Applied Energy Research Faculty and Staff Publications

Microalgae are a potential means of recycling CO₂ from industrial point sources. With this in mind, a novel photobioreactor (PBR) was designed and deployed at a coal-fired power plant. To ascertain the feasibility of using waste heat from the power plant to heat algae cultures during cold periods, two heat transfer models were constructed to quantify PBR cooling times. The first, which was based on tabulated data, material properties and the physical orientation of the PBR tubes, yielded a range of heat transfer coefficients of 19–64 W m⁻² K⁻¹ for the PBR at wind speeds of 1–10 …

Modeling The Interplay Between Photosynthesis, Co2 Fixation, And The Quinone Pool In A Purple Non-Sulfur Bacterium, Adil Alsiyabi

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

Rhodopseudomonas palustris CGA009 is a purple non-sulfur bacterium (PNSB) that can fix CO₂ and nitrogen or break down organic compounds for its carbon and nitrogen requirements. Light, inorganic, and organic compounds can all be used for its source of energy. Excess electrons produced during its metabolic processes can be exploited to produce hydrogen gas or biodegradable polyesters (polyhydroxybutyrate). A genome-scale metabolic model of the bacterium was reconstructed to study the interactions between photosynthesis, carbon dioxide fixation, and the redox state of the quinone pool. A comparison of model-predicted flux values with published in vivo MFA fluxes resulted in predicted …

Bioproduction Of Adipic Acid Using Engineered Pseudomonas Putida Kt2440 From Lignin-Derived Aromatics, Howard Willett

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

Current industrial synthesis of adipic acid is nonrenewable and depends on a carcinogenic starting material, benzene. Biocatalysis with an engineered microorganism could turn a renewable feedstock into a value-added chemical such as adipic acid. Here we engineered P. putida KT2440 to transform lignin-derived aromatics, coumarate and ferulate, into adipic acid. Lignin is a recalcitrant plant biopolymer burned for thermal energy. Conversion of lignin into a value-added chemical will improve the efficiency of lignocellulose processing plants. The best performing engineered KT2440 strain produces 2.52 mM adipate at a 9.5% (mole/mole) yield. This was achieved by the genetic insertion of non-natural biosynthetic …

Ranking And Clustering Of Drosophila Olfactory Receptors Using Mathematical Morphology, Jayanta Kumar Das, Pabitra Pal Choudhury, Neelambuj Chaturvedi, Mohd Tayyab, Sk Sarif Hassan

Journal Articles

This article introduces an alignment-free clustering method in order to cluster all the 66 DORs sequentially diverse protein sequences. Two different methods are discussed: one is utilizing twenty standard amino acids (without grouping) and another one is using chemical grouping of amino acids (with grouping). Two grayscale images (representing two protein sequences by order pair frequency matrices) are compared to find the similarity index using morphology technique. We could achieve the correlation coefficients of 0.9734 and 0.9403 for without and with grouping methods respectively with the ClustalW result in the ND5 dataset, which are much better than some of the …

Carbon Nanotube And Cellulose Nanocrystal Hybrid Films, Mingzhe Jiang, Robert Seney, Paul Charles Bayliss, Christopher L. Kitchens

Publications

The use of cellulose nanocrystals (CNC) in high performance coatings is attractive for micro-scale structures or device fabrication due to the anisotropic geometry, however CNC are insulating materials. Carbon nanotubes (CNT) are also rod-shaped nanomaterials that display high mechanical strength and electrical conductivity. The hydrophobic regions of surface-modified CNC can interact with hydrophobic CNT and aid in association between the two anisotropic nanomaterials. The long-range electrostatic repulsion of CNC plays a role in forming a stable CNT and CNC mixture dispersion in water, which is integral to forming a uniform hybrid film. At concentrations favorable for film formation, the multiwalled …

Fibrinogen, Factor Xiii And Fibronectin: A Biophysical And Kinetic Characterization Of Their Interactions, Frank Fabian

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

The development of recombinant-based liquid fibrin tissue sealants having enhanced hemostatic and wound healing properties will involve understanding as yet not well characterized interactions between fibrinogen, fibrin (Fbn) factor XIII, thrombin and fibronectin. We study these phenomena in the context of comparing plasma derived fibrinogen to recombinant fibrinogen (rFI) produced in the milk of transgenic cows. An abundance of purified γγ and γγ’ FI subspecies enables detailed study of γγ or γγ’ biomonomer and their respective Fbn biopolymer formation as having different substrate behaviors of activated plasma derived factor XIII (pFXIIIa₂b₂). High pressure size exclusion (HPSEC) …

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Maximizing And Modeling Malonyl-Coa Production In Escherichia Coli, Tatiana Thompson Silveira Mello

LSU Master's Theses

In E. coli, fatty acid synthesis is catalyzed by the enzyme acetyl-CoA carboxylase (ACC), which converts acetyl-CoA into malonyl-CoA. Malonyl-CoA is a major building block for numerous of bioproducts. Multiple parameters regulate the homeostatic cellular concentration of malonyl-CoA, keeping it at a very low level. Understanding how these parameters affect the bacterial production of malonyl-CoA is fundamental to maximizing it and its bioproducts. To this end, competing pathways consuming malonyl-CoA can be eliminated, and optimal nutritional and environmental conditions can be provided to the fermentation broth. Most previous studies utilized genetic modifications, expensive consumables, and high-cost quantification methods, making …

The Synthesis, Purification, And Characterization Of The P3 Peptoid, Myles Joyce

Chemical Engineering Undergraduate Honors Theses

The relatively young field of nano-systems has vast applications over various different fields. Peptoids (peptide analogues) and their uses are consistently investigated components of these nano-studies. A particularly interesting group of peptoids are able to self-assemble into secondary structures under the right conditions. The P3 peptoid is able to form microspheres if properly synthesized and purified. Microspheres are frequently studied due to their low surface area to volume ratios. This unique aspect of microspheres makes them an excellent candidate for drug delivery systems; however, these systems must also be robust so that the desired compound can be encapsulated within the …