Biochemical and Biomolecular Engineering Commons^™

Mechanisms Of Pathogen Inactivation In Wastewater And Pharmaceutical Applications, Christa L. Meingast

Dissertations, Master's Theses and Master's Reports

Infectious diseases are a significant threat to public health. Though society enacts practices to prevent the spread of these dangerous diseases, challenges remain. Therefore, continual advancements in treatment and prevention are required. Wastewater treatment and viral clearance in pharmaceutical applications are two key health measures that prevent the spread of infections.

A low-cost, low-technology biosolids treatment process was developed to improve wastewater treatment by collecting key information on storage temperature, ammonia, volatile solids, moisture content, pH, and pathogen inactivation in biosolids over long-term storage at two wastewater treatment plants located in northern climates of the United States. Inactivation of pathogens …

A Framework For Heterologous Biosynthesis Of Natural Products In Mammalian Cells Via Polymer-Mediated Transfections, Logan Warriner

Theses and Dissertations--Chemical and Materials Engineering

With the promise to treat a multi-faceted list of serious inherited and acquired diseases, such as cancer, neurodegenerative and infectious diseases, and inherited genetic indications, gene therapy has continued to push the boundaries of traditional medicine since its earliest implementation. While much progress has been made, clinical success has largely remained elusive. Immunogenicity, difficulty producing commercially relevant quantities, and having a limited genetic payload still limits the ability of viruses to act as directed delivery agents for genetic material. As such, researchers have turned to cationic synthetic materials as a means of delivering nucleic acids, which can circumvent the immune …

Heart Tissue Reconstruction By Light-Controlled Cell Adhesion, Patterning And Alignment On Decellularized Scaffolds, Cong Li

Theses and Dissertations--Chemical and Materials Engineering

There is an urgent demand for engineered tissues and organs because of extremely limited donor tissues available for transplant. The challenge of tissue rejection has motivated many researchers to try to remove all of the cells from a heart and then add back in patient matched cells. These recellularized hearts are a promising avenue towards a functional bioartifical heart that is less likely to be rejected. Decellularized extracellular matrix (ECM) scaffolds generated from animal hearts do not have the cellular components that elicit immune rejection in patient, and they also preserve the native heart tissue structure. While decellularization techniques are …

In Situ Image Processing And Data Binning Strategy For Particle Engineering Applications, Toufic El Arnaout, Patrick J. Cullen

Articles

Crystallization control can be improved through real-time monitoring technologies. Here, a workflow is demonstrated on rapid batch cooling crystallization of L-glutamic acid. First, in situ images were generated using video microscopy sensors and analyzed, by employing a single, rapid macro code to extract particle data descriptors. A binning procedure (over time) was performed, where every data point represented the counts of particles within a specific size or shape range per 100 images. This binning method was found more informative in tracking of the populations compared to whole image averages or individual particle datapoints. This study provides a step-by-step guide towards …

Property Estimation Of Palmitoylethanolamide And Sucrose Palmitate For Process Design From Methyl Palmitate, Janetiya Wongprathed

Chulalongkorn University Theses and Dissertations (Chula ETD)

Methyl palmitate is the primary component of palm oil-based biodiesel. It is a saturated fatty acid methyl ester which has a high melting point that results in low cold flow properties of biodiesel. Besides, lack of government support may affect the revenue of biodiesel business. For that reason, the producers turn attention to using biodiesel as a raw material for the production of value-added chemicals. Initially, we selected the studied products based on the gross profit margin, production process, market demand and application. This work simulated the production of palmitoylethanolamide, sucrose palmitate and normal alkanes from methyl palmitate using Aspen …

Higher Tensile Forces Across Cellular Junctions And An Intact Nuclear Linc Complex Is Required For Epithelial Function And Stability, Fnu Vani Narayanan

Theses and Dissertations

Recent advances in three-dimensional (3D) cell culture systems have provided key insights into the understanding of biochemical and physiological states of native tissue. A significant progress in the field of mechanobiology involves measuring cellular traction forces in a more native 3D environment. However, the effects of mechanical forces exerted across cellular junctions and the nuclear LINC complex, in an organized 3D system has not been investigated thus far. Epithelial cells spontaneously form acini (also known as cysts or spheroids) with a single, fluid-filled central lumen, when grown in 3D matrices. The size of the lumen is dependent on apical secretion …

Reaction Profiling Of Extracellular Protein Phosphorylation Through A Microfluidic Reactor Coupled With Raman Spectroscopy, Abigail Casey

Theses and Dissertations

Diseases and disorders in the human body are considered abnormalities of proper cellular function. Understanding the signal transduction mechanisms that cause these abnormalities is crucial to developing earlier detection methods, better treatment options and effective cures. While current diagnostic procedures are powerful tools in diagnosing diseases, they are ineffective in informing physicians on the real-time behavior of the signal transduction mechanisms associated with diseases and disorders. Currently, disease progression is monitored over time through routine patient visits and testing by one or more of the above techniques. By developing an approach that can monitor structural and conformational changes of proteins …

A New Interpretation Of The √7×√7 R19.1° Structure For P Adsorbed On A Ni(111) Surface, Elizabeth Barrow, Grant S. Seuser, Hiroko Ariga-Miwa, Donna A. Chen, Jochen A. Lauterbach, Kiyotaka Asakura

Faculty Publications

We have studied P adsorption on Ni(111), a system which shows complex adsorbate structures. We determined the phase diagram of the surface P adsorbed on Ni(111). At low coverage, amorphous P was observed. At temperatures between 373 and 673 K and coverages above 0.1 monolayer, we found a √7×√7 R19.1° structure, but above 673 K, other complex structures were created. These structures seemed to correlate with each other and we reinterpret a √7×√7 R19.1° structure of P adsorbed on Ni(111) based on the similarities of these surface structures. The new rectangular structure for the √7×√7 19.1° is discussed in relation …

A New Interpretation Of The √7×√7 R19.1° Structure For P Adsorbed On A Ni(111) Surface, Elizabeth Barrow, Grant S. Seuser, Hiroko Ariga-Miwa, Donna A. Chen, Jochen A. Lauterbach, Kiyotaka Asakura

Faculty Publications

We have studied P adsorption on Ni(111), a system which shows complex adsorbate structures. We determined the phase diagram of the surface P adsorbed on Ni(111). At low coverage, amorphous P was observed. At temperatures between 373 and 673 K and coverages above 0.1 monolayer, we found a √7×√7 R19.1° structure, but above 673 K, other complex structures were created. These structures seemed to correlate with each other and we reinterpret a √7×√7 R19.1° structure of P adsorbed on Ni(111) based on the similarities of these surface structures. The new rectangular structure for the √7×√7 19.1° is discussed in relation …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

A Microfluidic Paper-Based Analytical Device For Early Diagnosis And Prognosis Of Acute Myocardial Infarction, Lim Wei Yin

Student Works (2020-2029)

Acute myocardial infarction (AMI), also termed as heart attack, is often clinically screened by blood test through the measurement of cardiac biomarkers (i.e., troponin (T or I), creatine kinase (CK−MB) and myoglobin) and electrocardiography (ECG) changes which are presented to the hospital. However, the early diagnosis of AMI is challenging because the detection of biomarkers such as troponin (T or I) and CK−MB are only reliable at the intermediate and later stages (> 6 hours after chest pain onset), during myocardial injury and myocardial infarction. On the other hand, myoglobin often been used as early biomarker which is detectable within …

Design And Development Of A Perfusion Bioreactor With Internal Volume Expansion And Cell Retention For Cell And Gene Therapy Manufacturing, Corinna Doris

KGI Theses and Dissertations

Economically producing patient-specific cell therapies at commercial levels remains a challenge as it requires manufacturing separate batches per patient where the production system must be scaled-out rather than scaled-up to supply more patient doses. The resulting high production cost and consequent price-point can limit patient access. Specifically, the current cell expansion processes are highly manual and laborious, with the number and complexity of operations and components increasing the opportunities for failure and contamination. This work therefore aims to design a mechanically simple bioreactor that is better suited for scale-out by consolidating the cell expansion process to fewer components, vessels, and …

Development Of A Comsol Microdialysis Model, Towards Creation Of Microdialysis On A Chip With Improved Geometries And Recovery, Patrick Pysz

Graduate Theses and Dissertations

Microdialysis (µD) sampling is a diffusion-limited sampling method that has been widely used in different biomedical fields for greater than 35 years. Device calibration for in vivo studies is difficult for current non-steady state analytes of interest correlated with both inflammatory response and microbial signaling molecules (QS); which exist in low ng/mL to pg/mL with molecular weights over a wide range of 170 Da to 70 kDa. The primary performance metric, relative recovery (RR), relating the collected sample to the extracellular space concentration varies from 10% to 60% per analyte even under controlled bench-top conditions. Innovations in microdialysis device design …

In-Situ Extraction And Impregnation Of Black Walnut Husk Into Polyethylene Film Using Supercritical Carbon Dioxide With An Ethanol Modifier, Johnathon Wenzel, Veronica Moorman, Lihua Wang, Cheryl S. Samaniego, Michelle Ammerman, Isaiah Spencer-Williams, Mitchell Hall

Chemical Engineering Publications

Walnuts are commonly cultivated for their kernel, which is a rich source of antioxidant phenolic compounds. The husk likewise contains antioxidant and antimicrobial compounds, but is typically discarded without further processing. Antioxidant compounds are useful in creating active packaging films, but typically decompose at melt extrusion temperatures in polymer processing. Due to carbon dioxide's low critical point and ability to swell polymer films, supercritical carbon dioxide may be used to impregnate phenolic compounds into polymers. For this study, a novel technique is used to simultaneously produce walnut husk extracts and impregnate the extract into polymer films in the same batch …

Gradient Precipitation Of Recombinant Proteins Contained In Silkworm Larvae (Bombyx Mori) With Ammonium Sulphate, Abdurhakhmanov Jaloliddin, Sasmakov Sobirdjan, Khasanov Shuhrat, Ashirov Оybek

CHEMISTRY AND CHEMICAL ENGINEERING

We investigated the protein extract of silkworm larvae. For the first time, an extract containing proteins from silkworm larvae, obtained by fractional precipitation using ammonium sulfate, was studied. As a result of experiment is established, that solutions of ammonium sulfate with a concentration from 20% to 65% are optimal for the sedimentation of protein molecules with a mass in the range of 25 and 45 kDa. Optimal results of the study proposed to use in the process of purification of recombinant proteins.

A Review Of Materials For Managing Bone Loss In Revision Total Knee Arthroplasty, Romina Shafaghi, Omar Rodriguez, Emil H. Schemitsch, Paul Zalzal, Stephen D. Waldman, Marcello Papini, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

In 2014–2015, 61,421 total knee arthroplasties (TKAs) were performed in Canada; an increase of about 20% over 2000–2001. Revision total knee arthroplasties (rTKAs) accounted for 6.8% of TKAs performed between 2014 and 2015, and this is estimated to grow another 12% by 2025. rTKAs are typically more complicated than primary TKAs due to the significant loss of femoral and tibial bone stock. The escalating demand and limitations associated with total knee arthroplasty and their revision drives the development of novel treatments. A variety of materials have been utilized to facilitate regeneration of healthy bone around the site of a knee …

Development And Characterisation Of High Surface Energy Microstructured Sol-Gel Coatings For Sensing Applications, Emma Machugh

Doctoral

This study investigates the development of high surface energy photoreactive organic inorganic hybrid sol-gel coatings for the microstructuration of high-resolution microfluidic platforms and optofluidic biosensor platforms by standard photolithography processes. To achieve this, the first step of our work consisted of identifying the fundamental physico chemical processes governing the structuration and surface properties of hybrid organic inorganic sol-gel coatings. For this purpose, a reference material based on the combination of an organosilane (3-Methacryloxypropytrimethoxysilane, MAPTMS) and a transition metal (zirconium propoxide, ZPO), was firstly developed and characterised. It was highlighted that chemical, physical and combined physical and chemical processes can be …

Selection Of Optimal Conditions For The Cultivation Of Insect Cells For Use In Biotechnology, Khasanоv Shuhrat, Sasmakоv Sobir, Abdurakhmanоv Jaloliddin, Ashirоv Оybek

CHEMISTRY AND CHEMICAL ENGINEERING

The article discusses use of the insect cell cultures for biotechnological purposes. Optimal conditions for the cultiva-tion of Spodoptera exigua and Lymantria dispar cell lines were selected.

Development Of A Method Of Oriented Immobilization Of Lipases On A Solid Carrier, Ziyavitdinov Jamolitdin Fazlitdinovich, Inogamov Utkir Kudratillayevich, Berdiev Nodir Sharifovich, Ishimov Uchkun Jomuradovich

CHEMISTRY AND CHEMICAL ENGINEERING

The methods of oriented immobilization of lipases on a solid carrier - Silochrome C-80 have been developed. The resulting sorbents were tested in the process of obtaining biodiesel from cotton oil. It was shown that immobilized lipase on Silochrome C-80 with NH2 group has the highest transetrification ability and stability, while in sorbents with the enzyme immobilized with -COOH and -SH groups this value was 87 and 53%, respectively. Biocatalysis using an affinity sorbent of immobilized lipase with the –NH2 group has a high operational stability, which, after 240 hours of operation, retains more than 50%, and after 480 hours, …

Systems, Apparatus And Method For Material Preparations And / Or Handling, Robert Doebler, Ali Nadim, James D. Sterling, Anna Hickerson, Barbara Erwin, Denice Woyski, Ryan P. Talbot, Bruce Irvine

Business and Information Technology Faculty Research & Creative Works

Oscillating angularly rotating a container containing a mate rial may cause the material to be separate. Denser or heavier material may unexpectedly tend to be collected relatively close to the axis of rotation, while less dense or light material may tend to collect relatively away from the axis of rotation. Oscillation along an arcuate path provides high lysing efficiency. Alternatively, a micromotor may drive an impeller removably received in a container. Lysing may be implemented in batch mode, flow - through stop or semi-batch mode, or flow - through continuous mode. Lysing particulate material may exceed material to be lysed …