Cobalt-Doped Todorokite Prepared By Refluxing At Atmospheric Pressure As Lithium-Ion Battery Cathode,
2010
Key Laboratory of Subtropical Agriculture Resource and Environment,Ministry of Agriculture,Huazhong Agricultural University,Wuhan430070,China;
Cobalt-Doped Todorokite Prepared By Refluxing At Atmospheric Pressure As Lithium-Ion Battery Cathode, Rui-Qi Li, Chun-Hua Song, Chao Xu, Li-Xing Tu, Guo-Hong Qiu, Fan Liu
Journal of Electrochemistry
Cobalt-doped todorokites were prepared by refluxing at atmospheric pressure,and then charactered by X-ray diffraction(XRD),thermogravimetry(TG) and the analysis of chemical compositions.These measurements showed that all of the refluxing products were single phase of todorokites and the structure formulas were MgxCoyMnOz·nH2O,where 0.18 ≤ x ≤ 0.22,0 ≤ y ≤ 0.24,2.10 ≤ z ≤ 2.53,and 0.35 ≤ n ≤0.73.The electrochemical characteristics of cobalt-doped todorokites were examined as lithium insertion hosts for cathodes in rechargeable lithium batteries.The first discharge capacity of undoped todorokite electrode was 211 mAh/g and the discharge capacity became 37 mAh/g after 30 …
Fabrication And Characterization Of The Ni-Scsz Composite Anodes With A Lscm-Ceo2 Catalyst Layer In Thin Film Sofc,
2010
Institute of Fuel Cell,Shanghai Jiaotong University,Shanghai 200240,China;
Fabrication And Characterization Of The Ni-Scsz Composite Anodes With A Lscm-Ceo2 Catalyst Layer In Thin Film Sofc, Yun-Yun Wang, Bo Huang, Xin-Jian Zhu, Wan-Qi Hu, Qing-Chun Yu
Journal of Electrochemistry
Solid oxide full cell(SOFC) running directly on hydrocarbon fuels has attracted much attention in recent years. In this paper, a dual-layer structure anode was fabricated by tape casting and screen printing method. The addition of a LSCM-CeO2 catalyst layer to the supported anode surface yielded better performance in ethanol fuel. The maximum power density reached 710 and 669 mW/cm2 at 850 ℃ running on hydrogen gas steam and ethanol steam,respectively. No significant degradation in performance has been observed after 216 h of cell testing when the Ni-ScSZ13 anode was exposed to the ethanol steam at 700 ℃. Very …
Performance Of Sulfur-Super Conductive Carbon Black Composite In Electrolyte Mixed With Room Temperature Ionic Liquid,
2010
Institute of New Energy Material Chemistry,Nankai University,Tianjin 300071,China;
Performance Of Sulfur-Super Conductive Carbon Black Composite In Electrolyte Mixed With Room Temperature Ionic Liquid, Bo Zhang, Si-Ting Chen, Xue-Ping Gao
Journal of Electrochemistry
The sulfur-super conductive carbon black composite was prepared as cathode material of lithium/sulfur battery.The composite was characterized by scanning electron microscopy(SEM),X-ray diffraction(XRD),and electrochemical impedance spectroscopy(EIS).The sulfur composite shows a high discharge capacity and a good cycle performance in electrolyte mixed with 50% of room temperature ionic liquid.In particular,the discharge capacity of the composite was stabilized at 483.6 mAh/g after 50 cycles.
Electrochemical Properties Of Ni(Oh)2 Doped By Nio,
2010
School of Chemical Engineering and Environmental Science,Beijing Institute of Technology,Beijing 100081,China;
Electrochemical Properties Of Ni(Oh)2 Doped By Nio, Fei-Biao Chen, Bo-Rong Wu, Wei-Feng An, Zhao-Jun Yang, Feng Wu, Shi Chen
Journal of Electrochemistry
The Ni(OH)2 cathode material of MH/Ni was doped by NiO,which behaves as a capacitor and can improve the charge-discharge rate capacity of Ni(OH)2.The electrochemical properties of Ni(OH)2 was characterized by charge-discharge curves and cyclic voltammetry.The results showed that the material had the best discharge property when doped by 5% NiO,and the discharge specific capacity could reach 310.1 mAh/g at 0.2 C rate and remianed 79.5% at 3 C rate.The difference oxidation and reduction potentials between the of the battery was 164 mV when the Ni(OH)2 was doped by 5% NiO,which showed a good cyclic property.
Study Of Electrodes Modified With Hybrid Copper Cobalt Hexacyanoferrate-Mwcnts Composites,
2010
College of Material Science and Engineering,Sichuan University,Chengdu,610064,China;
Study Of Electrodes Modified With Hybrid Copper Cobalt Hexacyanoferrate-Mwcnts Composites, Shan Jiang, Yun Zhang, Xiao-Yan Wang, Xiao-Fei Yao
Journal of Electrochemistry
The hybrid modified electrodes were obtained by electrochemical deposition of copper-cobalt hexacyanoferrate(CuCoHCF) /multi-walled carbon nanotubes(MWCNTs) on the surface of glassy carbon electrode.The effects of the amount of MWCNTs and composition of electrolyte on the properties of modified electrode had been researched.The copper cobalt hexacyanoferrate-MWCNTs modified electrodes show excellent electrochemical properties compared with that modified only copper-cobalt hexacyanoferrate.The CuCoHCF-MWCNTs/GCE exhibits obvious electrocatalytic activity towards oxidation of hydrogen peroxide.The oxidation peak current increased linearly with the concentration of hydrogen peroxide in the range of 3.16 × 10-5 ~ 2.92 × 10-3 mol· L-1.The linear equation is given up …
Self-Activating Safety Mechanisms For Li-Ion Batteries,
2010
College of Chemistry and Molecular Sciences,Hubei Key Lab.of Eletrochemical Power Sources,Wuhan University,Wuhan 430072,China;
Self-Activating Safety Mechanisms For Li-Ion Batteries, Xin-Ping Ai, Yu-Liang Cao, Han-Xi Yang
Journal of Electrochemistry
The safety concerns of LIBs are considered to be a main obstacle to their high rate or large capacity applications in electric vehicles.This paper describes briefly our research works on the development of self-activating safety mechanisms for LIBs,including redox shuttle,potential-sensitive separator,temperature-sensitive electrode,and fire-retardent electrolyte.The problems and future in this research area are also discussed.
Preparation And Characterizations Of Li3V2(Po4)3 Cathode Material For Lithium Ion Batteries,
2010
College of Physics,Beihua University,Jilin 132013,Jilin,China;College of Materials Science and Engineering,Jilin University,Changchun 130012,China;
Preparation And Characterizations Of Li3V2(Po4)3 Cathode Material For Lithium Ion Batteries, Hong Chen, Tao Jiang, Chun-Zhong Wang, Gang Chen, Ying-Jin Wei
Journal of Electrochemistry
The carbon-coated Li3V2(PO4)3 was prepared by carbothermal reduction method.The structural and morphological properties of the material were studied by X-ray diffraction,FTIR and transmission electron microscopy.The synthesized material was a pure phase of Li3V2(PO4)3,with the particle size of about 100 nm.The values of Li ion diffusion coefficient of the material in the potential window of 3.0 ~ 4.3 V were nearly 3 orders larger than those in 3.0 ~ 4.8 V.In addition,the charge-transfer resistances in 3.0 ~ 4.3 V were much smaller than those in 3.0 …
Investigation Of Ceo2 As Cathode Electrocatalyst For Direct Borohydride Fuel Cell,
2010
State Key Laboratory of Advanced Technology for Materials Synthesis and Processing,Wuhan University of Technology,Wuhan 430070,China;
Investigation Of Ceo2 As Cathode Electrocatalyst For Direct Borohydride Fuel Cell, Xue-Min Ni, Ya-Dong Wang, Mu Pan
Journal of Electrochemistry
The performance of CeO2 as oxygen reduction electrocatalyst in direct borohydride fuel cell was investigated.The experimental results indicate that CeO2 shows significant electrocatalytic performance for oxygen reduction and exhibits no observed promotion effect on hydrolysis or electro-oxidation of BH4-.The power density of experimental one-compartment fuel cell with CeO2 as cathode electrocatalyst can reach a 67.8 mW·cm-2 at room temperature.
Preparation And Electrochemical Behavior Of Li4Ti5O12 Nanosheets As Anode Material For Lithium Ion Battery,
2010
School of Chemistry and Chemical Technology,Shanghai Jiao Tong University,Shanghai 200240,China;
Preparation And Electrochemical Behavior Of Li4Ti5O12 Nanosheets As Anode Material For Lithium Ion Battery, Yi-Fei Wang, Yu-Feng Tang, Zheng Qiu, Li Yang
Journal of Electrochemistry
Spinel lithium titanate(Li4Ti5O12) nanosheets with a size range of 200 ~400 nm were synthesized by hydrothermal process from the amorphous hydrous titanium oxide precursors.The as-prepared products were characterized by X-ray powder diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The electrochemical behaviors of Li4Ti5O12 electrode in conventional organic electrolyte and ionic liquid electrolyte were investigated by using cyclic voltammetry,galvanostatic charge-discharge and AC impedance techniques.The experimental results indicate that the as-prepared nanostructured Li4Ti5O12,evaluated as anode material,exhibited good reversibility and cycle performance.It is expected to be a …
Studied Corrosion Behaviors Of Reinforcing Steel In Concrete By A Single-Dimensional Array Electrode,
2010
State Key Laboratory for Physical Chemistry of Solid Surfaces,and Department of Chemistry,College of Chemistry and Chemical Engineering,Xiamen University,Xiamen 361005,Fujian,China;
Studied Corrosion Behaviors Of Reinforcing Steel In Concrete By A Single-Dimensional Array Electrode, Lan-Qiang Li, Shi-Gang Dong, Rong-Gui Du, Chang-Jian Lin
Journal of Electrochemistry
A single-dimensional array electrode was developed as a new electrochemical technique to image corrosion potential,galvanic current and polarization curves of reinforcing steel in concrete during corrosion process.Combining with the polarization behavior for each micro-electrode,the interactions between corrosion macrocell and corrosion microcell of the steel in concrete were evaluated.It was noticed that the corrosion macrocell and microcell occurred independently in difference regions at the initial stage of corrosion.The corrosion macrocell current can be in situ followed by corrosion potential imaging.The corrosion propagation of steel in concrete is closely related to the interactions between corrosion macrocell and corrosion microcell.
Electrosynthesis Of P-Aminobenzenearsenic Acid,
2010
State Key Laboratory Breeding Base of Green Chemisitry Synthesis Technology,Zhejiang University of Technology,Hangzhou 310032,China;
Electrosynthesis Of P-Aminobenzenearsenic Acid, Chun-An Ma, Qin-An Zheng, Qiang Zhou, Ying-Hua Xu
Journal of Electrochemistry
The electrochemical reduction of p-nitrophenyl arsonit acid to p-aminobenzenearsenic acid was studied using controlled-current electrolysis.The results showed that the yield of p-aminobenzenearsenic acid was determinated by the following factors:the concentrations of sulphuric acid,the amount of additive,temperature and the concentrations of p-nitrophenyl arsenic acid.The optimum electrolytic conditions were obtained to be is 10% H2SO4,1% NaCl,80 ℃,25 g/350 mL p-nitrophenyl arsenic acid and 10 A·dm-2.The yield of arsanilic acid could be reached 64.7% under the optimum electrolytic conditions.
Electrocatalytic Reduction Of L-Cystine At Pb/Nanotio2 Film Electrode,
2010
Anhui Key Laboratory of Functional Molecular Solids & Molecular Based Materials,College of Chemistry and Materials Science,Anhui Normal University,Wuhu 241000,Anhui,China;
Electrocatalytic Reduction Of L-Cystine At Pb/Nanotio2 Film Electrode, Dao-Bao Chu, Feng Wang, Ying Xiao, Xue-Jiao Zhang
Journal of Electrochemistry
The nanoporous Ti-based TiO2 films electrodes modified with Pb particles(Pb/nanoTiO2) were prepared by using anodization and potentiostatic electro-deposition.The optimum deposition conditions were determined by comparing with various deposition potentials and time.The SEM analyses indicated that the TiO2 films were homogeneous nanoporous structure,and the Pb particles well dispersed on the TiO2 films.The L-cystine electrocatalytic activity reduction on the Pb/nanoTiO2 film electrodes was investigated by cyclic voltammetry and Chronoamperometric curves.The results showed that this type of the electrode posseses high acticity and stability.
Application Of Sol-Gel Technology In The Of Activation Process Of Chemical Plating Pretreatment,
2010
Key Laboratory of Science & Technology of Eco-Textile,Ministry of Education,Donghua University,Shanghai 201620,China;
Application Of Sol-Gel Technology In The Of Activation Process Of Chemical Plating Pretreatment, Lin Zhang, Wei Wang, Qian-Zhen Wu
Journal of Electrochemistry
Using KH-550 as precursors,gel thin films were formed on fabric by sol-gel method.By complexed with palladium ions due to the presences of amido and hydroxide in the gel thin films,the aggregation of palladium particles was inhibited.Therefore,Palladium could exhibit better catalytic activity in the process of electroless plating.The surface morphology of fabric was observed by SPM and SEM.Campared with the traditional pretreatment process,no SnCl2 was needed.This method reduced pollution,shortened process flow and reduced the amount of noble metals.
Dual-Action Hygienic Coatings: Benefits Of Hydrophobicity And Silver Ion Release And Surface Analysis,
2010
Technological University Dublin
Dual-Action Hygienic Coatings: Benefits Of Hydrophobicity And Silver Ion Release And Surface Analysis, Niall Stobie, Brendan Duffy, John Colreavy, Patrick Mchale, Steven Hinder, Declan Mccormack
Articles
Coatings that demonstrate reduced attachment of crystalline precipitates and the medical device colonising Staphylococcus epidermidis were prepared by the immobilisation of silver doped perfluoropolyether–urethane siloxane thin films on glass substrates. The presence of stratified hydrophobic perfluoropolyether groups protects the coating surface from the attachment of crystalline hydrophilic species such as chlorides and phosphates, whilst silver ion release inhibited attachment of S. epidermidis and subsequent biofilm formation in vitro. The release of silver ions protects the perfluoro groups from the hydrophobic interactions of S. epidermidis cells, which can reduce the hydrophobicity of the protective coating. These coatings also exhibited significant antibacterial …
Microscopic Formulation Of The Zimm-Bragg Model For The Helix-Coil Transition,
2010
Portland State University
Microscopic Formulation Of The Zimm-Bragg Model For The Helix-Coil Transition, A. V. Badasyan, A. Giacometti, Y. S. Mamasakhlisov, V. F. Morozov, Albert S. Benight
Chemistry Faculty Publications and Presentations
A microscopic spin model is proposed for the phenomenological Zimm-Bragg model for the helix-coil transition in biopolymers. This model is shown to provide the same thermophysical properties of the original Zimm-Bragg model and it allows a very convenient framework to compute statistical quantities. Physical origins of this spin model are made transparent by an exact mapping into a one-dimensional Ising model with an external field. However, the dependence on temperature of the reduced external field turns out to differ from the standard one-dimensional Ising model and hence it gives rise to different thermophysical properties, despite the exact mapping connecting them. …
Elucidation Of Fragmentation Pathways Of Nitrile-Terminated Ppi Dendrimer-Metal Complexes,
2010
Marshall University
Elucidation Of Fragmentation Pathways Of Nitrile-Terminated Ppi Dendrimer-Metal Complexes, Kristen Nicole Pack
Theses, Dissertations and Capstones
The complexity of branching macromolecules around a core unit, such as poly(propylene)imine (PPI) dendrimers, has caught the attention of researchers for several years1,2,3,4,5. The structural framework of the core unit for these dendrimers is simply 1,4- diaminobutane. As the synthesis of higher-order generations of the macromolecule progresses, the molecules become very complex and tightly woven, but have predictable geometries and properties. The PPI dendrimers can be functionalized at the terminal ends of the branches in order to elicit different properties. The PPI dendrimer examined in this project has been terminated with a nitrile group rather than the usual …
Two-Dimensional To Three-Dimensional Structural Transition Of Gold Cluster Au 10 During
Soft Landing On Tio 2 Surface And Its Effect On Co Oxidation,
2010
University of Nebraska-Lincoln
Two-Dimensional To Three-Dimensional Structural Transition Of Gold Cluster Au 10 During Soft Landing On Tio 2 Surface And Its Effect On Co Oxidation, Hui Li, Yong Pei, Xiao Cheng Zeng
Xiao Cheng Zeng Publications
We investigate the possible structural transition of a planar Au10 cluster during its soft landing on a TiO2 (110) surface with or with no oxygen defects. The collision between the gold cluster and the oxide surface is simulated using the Car–Parrinello quantum molecular dynamics method. Both high-speed and low-speed conditions typically implemented in soft-landing experiments are simulated. It is found that under a high-speed condition, the gold cluster Au10 can undergo a sequence of structural transitions after colliding with a defect-free TiO2 (110) surface. When the TiO2 (110) surface possesses oxygen vacancies, however, chemical bonds …
Particle Matter Measurements For Inspection/Maintenance Programs,
2010
University of Denver
Particle Matter Measurements For Inspection/Maintenance Programs, Daniel Joseph Pope
Electronic Theses and Dissertations
Particle emissions from Heavy Duty Diesel Vehicles (HDDVs) are currently measured by opacity or dynamometer gravimetric analysis. The Electronic Tailpipe Particle Sensor (ETaPS) is an inexpensive measurement device purported to give real time response to particle mass and was proposed as a possible addition to Inspection/Maintenance (I/M) programs. There were three goals to this study. The first was to verify ETaPS response to particle mass of HDDV exhaust. Integrated ETaPS signal was plotted against filter weight from dynamometer gravimetric analysis and a correlation was found. The second goal was to find a correlation between ETaPS readings and the Remote Sensing …
Icosahedral B12-Containing Core–Shell Structures Of B80,
2010
University of Nebraska-Lincoln
Icosahedral B12-Containing Core–Shell Structures Of B80, Hui Li, Nan Shao, Bo Shang, Lan-Feng Yuan, Jinlong Yang, Xiao Cheng Zeng
Xiao Cheng Zeng Publications
Low-lying icosahedral (Ih) B12-containing structures of B80 are explored, and a number of core–shell isomers are found to have lower energy than the previous predicted B80 fullerene. The structural transformation of boron clusters from tubular structure to core–shell structure may occur at a critical size less than B80.
Graphene-Like Bilayer Hexagonal Silicon Polymorph,
2010
University of Nebraska-Lincoln
Graphene-Like Bilayer Hexagonal Silicon Polymorph, Jaeil Bai, Hideki Tanaka, Xiao Cheng Zeng
Xiao Cheng Zeng Publications
We present molecular dynamics simulation evidence for a freezing transition from liquid silicon to quasi-twodimensional (quasi-2D) bilayer silicon in a slit nanopore. This new quasi-2D polymorph of silicon exhibits a bilayer hexagonal structure in which the covalent coordination number of every silicon atom is four. Quantum molecular dynamics simulations show that the stand-alone bilayer silicon (without the confinement) is still stable at 400 K. Electronic band-structure calculations suggest that the bilayer hexagonal silicon is a quasi-2D semimetal, similar to a graphene monolayer, but with an indirect zero band gap.
