Manufacturing Commons^™

Battery Test Chamber, Olivia Cole, Noah Purdy, Jacob Happ

Williams Honors College, Honors Research Projects

A battery test chamber was designed for temperature-controlled experiments on batteries. The apparatus is a standalone desktop unit capable of testing a battery of maximum size 2.25” x 2.25” x 2”. There are two separate chambers divided by a rotating, 90° door. The chamber halves are used for heating and cooling the battery, respectively. An adjustable mount for the battery allows for variation in sample size and securely holds the battery throughout the experiment. The operator can twist a knob on top of the box to spin the battery between the hot and cold chambers. The hot side is equipped …

Guardian Condor, Kevin Bayonnet

Williams Honors College, Honors Research Projects

Our group has teamed up with Dr. Williams from Discovery Lab Global to research the capabilities of 3D printed Unmanned Aerial Vehicles (UAVs). The goal of our project is to deliver a 3D printed glider prototype which can later be fitted with electronics for controlled flight. The glider must also carry a payload of 2 to 3 pounds in addition to the electronics. These requirements must be met all while using a basic 3D printer with low cost plastic

Throughout the Fall 2017 semester, our group made a significant amount of progress by completing the conceptual design portion of the …

Human Powered Vehicle Design Team: Speed Variable Steering Stabilizer, Eric Miller, Matt Kraml

Williams Honors College, Honors Research Projects

The Human Powered Vehicle Competition (HPVC) is held annually by ASME at a few locations. The University of Akron has competed in the ASME-East and ASME-West competitions over the past handful of years against universities from all over the world. Objectives of each team for the competition are three-fold: vehicle design, racing performance, and innovation. Our senior design project involved working on the innovation concept for ASME-East 2018 held at Penn State University during the weekend of 4/13. Speed variable steering was decided upon by the entire HPVC team early in the design process as the innovation choice for this …

Indicator-Supporting Fixture Based On A Time And Motion Study, James Anthony

Williams Honors College, Honors Research Projects

The design goal of this project was proposed by the sponsor company, Jay-Em Aerospace in Cuyahoga Falls, Ohio. I was tasked with observing a process carried out in the Assembly department by multiple people and charged with coming up with a fixture to improve safety, speed, and accuracy of this task. To determine how to make the process safer, interviews were conducted with the people who would usually be carrying out this process and determined their top concerns and issues with how it is carried out currently. To improve the speed and accuracy of the process, a "time and motion …

Swagelok Adjustable Check Valve Setting Device, Brandon Sours, Paul Olson, David Race, Nick Rimpf

Williams Honors College, Honors Research Projects

Check valves are used to control the amount of flow through a valve and only open when a certain pressure is reached. The path of the fluid is strictly in one direction, which allows the valve to prevent any back flow within a system. They are also one of few self-automated piping system components that do not require assistance to open or close. Some check valves use a combination spring-and-nut compression assembly to set an opening pressure. As the nut is used to set the spring compression, and by extension the opening pressure, problems tend to arise when adjusting the …

Mht Assembly Line, Sean Lundholm

Williams Honors College, Honors Research Projects

The purpose of this report is to record the process followed and steps taken to design and implement a new product assembly line. While the implementation of the line required more than what is in this report, the projects outlined are those I was personally involved in and responsible for. This report will outline why the project was required, the steps taken to complete the project, and the challenges faced. Throughout the progression of the project, many different parts and areas were considered. As each of these was brought into focus, new challenges presented themselves and were dealt with accordingly. …

Human Powered Vehicle Frame Design, Analysis, Manufacturing, And Testing, Christopher Reed, Kole W. Williams

Williams Honors College, Honors Research Projects

The University of Akron Human Powered Vehicle Design Team began this academic year with a mission to create a practical, lightweight, safe, and efficient human powered vehicle. The main objectives of ZC18 were inspired by competition in the 2018 Human Powered Vehicle Challenge at ASME E-Fest East. In addition to adhering to the rules of this competition, scoring high on the submitted reports, and competing well in the racing events, the team set a goal to assist in furthering knowledge related to the topic of human powered vehicles.

ZC18 was constructed nearly completely in the University of Akron’s Design Center …

Consuming Digital Debris In The Plasticene, Stephen R. Parks

Theses and Dissertations

Claims of customization and control by socio-technical industries are altering the role of consumer and producer. These narratives are often misleading attempts to engage consumers with new forms of technology. By addressing capitalist intent, material, and the reproduction limits of 3-D printed objects’, I observe the aspirational promise of becoming a producer of my own belongings through new networks of production. I am interested in gaining a better understanding of the data consumed that perpetuates hyper-consumptive tendencies for new technological apparatuses. My role as a designer focuses on the resolution of not only the surface of the object through 3-D …

Task Complexity, And Operators’ Capabilities As Predictor Of Human Error: Modeling Framework And An Example Of Application, Maria Chiara Leva, Alberto Caimo, Rebecca Duane, Micaela Demichela, Lorenzo Comberti

Conference Papers

This paper presents the initial framework adopted to assess human error in assembly tasks at a large manufacturing company in Ireland. The model to characterize and predict human error presented in this paper is linked conceptually to the model introduced by Rasch (1980), where the probability of a specified outcome is modelled as a logistic function of the difference between the person capacity and item difficulty. The model needs to be modified to take into account an outcome that is not dichotomous and feed into the interaction between two macro factors: (a) Task complexity: that sum-marises all factors contributing to …

Capillary-Assisted Enhanced Condensation Heat Transfer For Low Surface Tension Liquids, Gnana Vishnu Durgam

Dissertations, Master's Theses and Master's Reports

Extensive research has been carried out over the course of the last few decades to induce dropwise condensation as it offers 5 - 7 times better heat transfer performance compared to filmwise condensation process. A number of methods such as low surface energy hydrophobic coatings, surface modification of hydrophobic surfaces to fabricate micro, nano and hierarchical structures, and the recent incorporation of jumping droplet phenomenon have provided effective means to further enhance the condensation heat transfer. However, existing methods to enhance condensation heat transfer rate fail in the case of low surface tension, highly wetting liquids such as hydrocarbons, cryogens, …

Investigation Of 2195 And 2219 Post Weld Heat Treatments For Additive Friction Stir Lap Welds, Matthew Champagne

LSU New Orleans Theses and Dissertations

To evaluate potential uses for friction stir welding in additive manufacturing, two separate parts were fabricated, one of 2195-T84 and the other 2219-T87, utilizing fixed pin techniques and additive lap welds. The parts were cut into samples, artificially aged and subjected to Rockwell hardness (HRB), Vickers hardness, micrographic photography, and metallographic imaging on both pre- and post- heat treatment. Additionally, tensile testing was performed on the heat-treated samples. A comparisons of test results showed a minimal increase in the yield strength of the 2195-T84 samples compared to as-welded tensile results obtained from a previous project. The ultimate tensile strength was …

The Vibe, Sarah P. Douglass

Capstones

The Vibe is a long-form narrative about where tech is taking the female orgasm. The piece concludes that physiological research is a required next step when creating the climax of the future.

http://sarahpdouglass.com

A Framework Towards Technology Creation In Africa: Focusing On Ghana, Martin Yao Donani, Hannatu Abue Kugblenu, Azindow Bawa Fuseini

International Journal of African Development

Underdevelopment in Africa has been historical and a global concern coupled with the quest for good governance. Several efforts have been made in academia, national governments, the international community, and other institutional arrangements to reverse the trend. These efforts however are yet to produce a lasting result as Africa is still characterized by low productivity output, poverty and a widening technology gap when compared to other developing regions of the world. Conventional approaches used to address the African problem have consistently been devoid of indigenous technology development. Technology is here seen as paramount to every form of production on which …

Usa Boccia Ball Ramp For Athletes With Quadriplegia, Alissa A. Koukourikos, Matthew Lee, Nathan Bernards

Mechanical Engineering

In this report, the design process in creating an assistive device for Boccia Classification 3 (BC3) players is outlined. The initial research steps, including research into the rules of the game, capabilities of the players, and existing products is documented to show where ideas for the product stemmed from. This transitions into requirements that the sponsor requested, and preliminary designs and ideas for the product. Finally, this report explains the details of the final design, which has been analyzed for safety, ease of use, and ability to function under different conditions. The processes of manufacturing and testing will also be …

Real Time And High Fidelity Quadcopter Tracking System, Tyler Mckay Hall

Computer Engineering

This project was conceived as a desired to have an affordable, flexible and physically compact tracking system for high accuracy spatial and orientation tracking. Specifically, this implementation is focused on providing a low cost motion capture system for future research. It is a tool to enable the further creation of systems that would require the use of accurate placement of landing pads, payload acquires and delivery. This system will provide the quadcopter platform a coordinate system that can be used in addition to GPS.

Field research with quadcopter manufacturers, photographers, agriculture and research organizations were contact and interviewed for information …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Single Tower Crane Allocation Models Using Ant Colony Optimization, Carlos Abelardo Treviño

Theses and Dissertations

The construction industry greatly benefits from the utilization of heavy machines and equipment to accomplish successful projects. Tower cranes, in specific, have a crucial role in the transportation of material loads across the site. Because these machines are fixed to the ground, it is essential for planners and managers to position them in a location that provides the most efficient transfer of materials possible. This is commonly known as the tower crane allocation problem, and many researchers have attempted to optimize the tower crane location using mathematical, artificial intelligence, and simulation approaches. However, many works from the literature contain critical …

Friction Stir Welding Manufacturing Advancement By On-Line High Temperature Phased Array Ultrasonic Testing And Correlation Of Process Parameters To Joint Quality, Daniel James Huggett

LSU Doctoral Dissertations

Welding, a manufacturing process for joining, is widely employed in aerospace, aeronautical, maritime, nuclear, and automotive industries. Optimizing these techniques are paramount to continue the development of technologically advanced structures and vehicles. In this work, the manufacturing technique of friction stir welding (FSW) with aluminum alloy (AA) 2219-T87 is investigated to improve understanding of the process and advance manufacturing efficiency. AAs are widely employed in aerospace applications due to their notable strength and ductility. The extension of good strength and ductility to cryogenic temperatures make AAs suitable for rocket oxidizer and fuel tankage. AA-2219, a descendent of the original duralumin …

Distributed Manufacturing Of Flexible Products: Technical Feasibility And Economic Viability, Aubrey Woern, Joshua M. Pearce

Department of Materials Science and Engineering Publications

Distributed manufacturing even at the household level is now well established with the combined use of open source designs and self-replicating rapid prototyper (RepRap) 3-D printers. Previous work has shown substantial economic consumer benefits for producing their own polymer products. Now flexible filaments are available at roughly 3-times the cost of more conventional 3-D printing materials. To provide some insight into the potential for flexible filament to be both technically feasible and economically viable for distributed digital manufacturing at the consumer level this study investigates 20 common flexible household products. The 3-D printed products were quantified by print time, electrical …

Application Of Surface Treatments To Improve Fuel Efficiency Of Internal Combustion Engines, Amirabbas Akbarzadeh

LSU Master's Theses

To improve the tribological performance of contacting surfaces, different surface modification methods can be employed. Surface texturing and surface coating are examples of viable techniques developed for this purpose. Surface texturing involves creating micropatterns on the contacting surfaces while surface coating requires depositing a thin layer of a suitable material on the surface(s) to improve the component’s friction and wear characteristics. The performance of textured surfaces is affected by the geometric characteristic of textures.When dealing with surface coating parameters, the parameters of interests are the type of coating materials and their thicknesses.

The current study aims to experimentally study the …

Note On The Rate And Energy Efficiency Limits For Additive Manufacturing, Timothy Gutowski, Sheng Jiang, Daniel Cooper, Gero Corman, Michael Hausmann, Jan-Anders Manson, Timo Schudeleit, Konrad Wegener, Matias Sabelle, Jorge Ramos-Grez, Dusan P. Sekulic

Mechanical Engineering Faculty Publications

We review the process rates and energy intensities of various additive processing technologies and focus on recent progress in improving these metrics for laser powder bed fusion processing of metals, and filament and pellet extrusion processing of polymers and composites. Over the last decade, observed progress in raw build rates has been quite substantial, with laser metal processes improving by about 1 order of magnitude, and polymer extrusion processes by more than 2 orders of magnitude. We develop simple heat transfer models that explain these improvements, point to other possible strategies for improvement, and highlight rate limits. We observe a …

Process Management And Design Layout Of High Throughput Screening, Anthony Vasquez, Kyle Dupuy

Industrial and Manufacturing Engineering

Calibr is a pharmaceutical company in San Diego and growing very quickly rate and need help redesigning their lab layout and in doing so reducing their cycle times and down times in machines. In addition to this, they do not currently have an accurate measurement of how long their processes take in an overall cycle. The objective of this project is to provide Calibr with a redesigned layout to accommodate new equipment as well as a software tool that can output Gantt charts for their planning of their testing. Our approach to this project first included mapping out the facilities …

Polar Exploration (University Focus) Research Into Smart Materials Continues At The University Of Dublin With The Development Of Methods To Record And Present Data To Demonstrate The Magnetorheological Effect When A Magnetic Field Is Applied To A Mr Elastomer Sample, Dave Gorman, Niall Murphy, Ray Ekins

Conference Papers

Research into methods to record and present data to demonstrate the Magnetorheological effect when a magnetic field is applied to a Magnetorheological Elastomer sample. By Dave Gorman, Niall Murphy and Ray Ekins, Technological University Dublin, Republic of Ireland A Magnetorheological Elastomer (MRE) is an example of a smart material as it undergoes a change in its physical properties when in the presece of an external magnetic field. This change in properties is known as the Magnetorheological (MR) effect and the manner in which it is achieved and reported, is of critical importance to the future development of MRE-based components. To …

Open Source 3-D Printed Nutating Mixer, Dhwani K. Trivedi, Joshua M. Pearce

Department of Materials Science and Engineering Publications

As the open source development of additive manufacturing has led to low-cost desktop three-dimensional (3-D) printing, a number of scientists throughout the world have begun to share digital designs of free and open source scientific hardware. Open source scientific hardware enables custom experimentation, laboratory control, rapid upgrading, transparent maintenance, and lower costs in general. To aid in this trend, this study describes the development, design, assembly, and operation of a 3-D printable open source desktop nutating mixer, which provides a fixed 20° platform tilt angle for a gentle three-dimensional (gyrating) agitation of chemical or biological samples (e.g., DNA or blood …

The Subject Librarian Newsletter, Engineering And Computer Science, Fall 2017, Buenaventura "Ven" Basco

Libraries' Newsletters

No abstract provided.

Pulsed Laser Beam Welding Of Pd43Cu27Ni10P20 Bulk Metallic Glass, Ling Shao, Amit Datye, Jiankang Huang, Jittisa Ketkaew, Sung Woo Sohn, Shaofan Zhao, Sujun Wu, Yuming Zhang, Udo D. Schwarz, Jan Schroers

Electrical and Computer Engineering Faculty Publications

We used pulsed laser beam welding method to join Pd₄₃Cu₂₇Ni₁₀P₂₀ (at.%) bulk metallic glass and characterized the properties of the joint. Fusion zone and heat-affected zone in the weld joint can be maintained completely amorphous as confirmed by X-ray diffraction and differential scanning calorimetry. No visible defects were observed in the weld joint. Nanoindentation and bend tests were carried out to determine the mechanical properties of the weld joint. Fusion zone and heat-affected zone exhibit very similar elastic moduli and hardness when compared to the base material, and the weld joint shows high …

On The Ramberg-Osgood Stress-Strain Model And Large Deformations Of Cantilever Beams, Ronald J. Giardina Jr

LSU New Orleans Theses and Dissertations

In this thesis the Ramberg-Osgood nonlinear model for describing the behavior of many different materials is investigated. A brief overview of the model as it is currently used in the literature is undertaken and several misunderstandings and possible pitfalls in its application is pointed out, especially as it pertains to more recent approaches to finding solutions involving the model. There is an investigation of the displacement of a cantilever beam under a combined loading consisting of a distributed load across the entire length of the beam and a point load at its end and new solutions to this problem are …

Analysis Of Variable Insensitive Friction Stir Welding Parameters, Robert L. Marrero Jr

LSU New Orleans Theses and Dissertations

Friction Stir Welding (FSW) was used to perform a Design of Experiment (DOE) to determine the welding parameters effects on yielding consistent mechanical properties across the length of the weld. The travel speed was varied across set forge force and RPM conditions, to find a dataset that will yield consistent mechanical properties independent of the travel speed. Six different welds were completed on two different aluminum panels, the advancing side being Aluminum alloy 2195-T8 at a thickness of .350”, with the retreating side being Aluminum alloy 2219-T851 with a gauge thickness of .360”. A Left-hand Right-hand self-reacting pin tool was …

Investigation Of Build Strategies For A Hybrid Manufacturing Process Progress On Ti-6al-4v, Lei Yan, Leon Hill, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The various processing parameters of a hybrid manufacturing process, including deposition and machining, is being investigated with a Design of Experiment (DoE). The intent was to explore the effect of different build strategies on the final part’s Vickers hardness, tensile test, fatigue life, and microstructure. From this experiment, the processing parameters can be linked to various mechanical properties. This will lead to the ability to create a combination of deposition and machining parameters, which will result in improved mechanical properties.

Review Of Am Simulation Validation Techniques, Aaron Flood, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Due to the complexity of Additive Manufacturing (AM), it can require many trial runs to obtain processing parameters which produce a quality build. Because of this trial and error process, the drive for simulations of AM has grown significantly. Simulations only become useful to researchers if it can be shown that they are true representations of the physical process being simulated. All simulations have different methods of validation to show that they are an accurate representations of the process. This paper explores the various methodologies for validation of laser based metal AM simulations, focusing mainly on the modeling of the …