Manufacturing Commons^™

Magnetic Field-Induced Transformation In Polycrystalline Ni2mnal Heusler Type Magnetic Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The martensitic and magnetic transformations, as well as the mechanical properties, of Ni₂MnAl alloys in as-cast (AC) and heat-treated (HT) conditions were investigated. Magnetic-field-induced strain was evaluated via magnetostriction, with reversible strains of 0.14% and 0.2% achieved in the martensitic phase at 2 K for the AC and HT alloys, respectively. Transformation temperatures and Curie temperatures were determined under constant applied magnetic field, revealing that γ-phase inclusions in the AC microstructure suppress antiferromagnetic domain response, yielding a lower magnetization (∼8.4 emu g⁻¹) compared to the HT alloy (∼13.4 emu g⁻¹). Both alloys exhibited hysteretic behavior in the martensitic state and …

Direct Ink Writing Of Functional Fiber/Granular Composites, Zhuoyuan Yang

Doctoral Dissertations and Master's Theses

Direct ink writing provides a versatile manufacturing route for fabricating functional fiber and granular composites with controlled architecture, tunable interfaces, and customized material distributions. Fiber reinforced composites offer high stiffness, strength, fatigue resistance, and functional anisotropy, while granular composites provide scalable access to particle based structures with high material efficiency and broad resource compatibility. However, the additive manufacturing of these composite systems remains challenging. For fiber based composites, precise control of fiber placement, matrix impregnation, interfacial bonding, and freestanding deposition is difficult to achieve during printing. For granular composites, stable particle flow, controllable packing, binder infiltration, and shape retention are …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Castrip Process Technology: Non-Grain Oriented (Ngo) Si Steels Extension And Carbide-Free Bainitic (Cfb) For Flat Products, Naram Naidu Meesala

Masters Theses

"This research explores the development of advanced steel grades manufactured through Castrip® twin-roll thin strip casting technology, with particular attention to non-grain-oriented electrical Si-Steels (NGOES) and carbide-free bainitic (CFB) steels. The Castrip® process offers a near-net-shape route for producing thin steel strips, which greatly decreases the number of processing stages, lowers energy demand, and reduces carbon dioxide emissions when compared with traditional steel production methods.

In the NGOES part of the study, several industrial Fe–Si steel compositions were cold rolled to final thicknesses ranging from 0.35 mm to 0.15 mm. These materials were then exposed to short-duration continuous annealing at …

Effect Of Complex Alloying Elements On Oxide Scale Formation And Water-Jet Descaling Performance On Continuously Cast Low-Carbon Steels, Tochukwu P. Ojiako, Tsvetkov Dmitry, Mario Buchely, Haiming Wen, Simon N. Lekakh, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

The formation and evolution of oxide scale in contact with mold flux during continuous casting, subsequent reheating, and hydraulic descaling are strongly governed by steel chemistry. To elucidate the effect of complex alloying elements (Si, Mn, and Cr), two industrially produced continuously cast low-carbon steel grades for manufacturing stamped parts (a base and alloyed steel grade) were investigated. The objective was to determine how alloying elements influence oxidation behavior, scale morphology, interfacial adhesion, and water-jet descaling efficiency. Continuously cast slab specimens were subjected to controlled thermal and atmospheric oxidation cycles simulating multistage industrial practice. Three initial surface conditions (industrial as-cast, …

Hydrogen Embrittlement In Shot-Peened Steel, Jia-Huei Tien, David R. Johnson, David Bahr

15th International Conference on Shot Peening

This work investigates the role of shot peening on hydrogen embrittlement resistance in quenched and tempered 1070 steel. Thermal desorption spectroscopy results revealed that shot-peened specimens contained nearly twice the hydrogen (H) content of unpeened samples when charged under the same electrochemical conditions, suggesting the introduction of additional trapping sites occur during peening. The mechanism underlying this behavior can be associated with increased dislocation density and is more consistent with the HELP mechanism. Residual stress measurements show a significant relaxation of compressive stresses in shot-peened specimen after H charging, indicating H enhanced dislocation rearrangement. Both unpeened and peened specimens exhibited …

Investigations On The Fatigue Strength Of Threads Produced By Different Fabrication Techniques, Philippe Du Maire, Jürgen Hoffmeister, Andreas Öchsner, Michael Johlitz

15th International Conference on Shot Peening

The increasing importance of sustainability in engineering demands the development of long-lasting, high-performance components that reduce material and energy consumption over time. This study investigates how different thread manufacturing processes, i.e., cutting, rolling, and deep rolling, affect the fatigue strength of bolts made from 42CrMo4+QT steel. Cylindrical specimens with M12 threads were subjected to cyclic tensile loading with constant mean stress. Fatigue strength was evaluated using the staircase method, and supporting analyses included X-ray diffraction for residual stress, and full width half maximum examination and Vickers microhardness measurements. Results show that thread rolling significantly improves fatigue strength, achieving 113.8 MPa …

Effect Of Fine Particle Peening Induced Material Transfer On The Initial Deposition Behavior Of Nickel Electroplating On Aluminum Substrate, Kazuki Iijima, Yutaka Kameyama, Hideaki Sato, Shuhei Kodama

15th International Conference on Shot Peening

Plating on aluminum requires a complex zincate pretreatment. Fine Particle Peening (FPP), using particles ≤200 µm, has gained attention as an alternative due to its ability to transfer particle components onto the surface, potentially improving deposition and adhesion. Previous studies showed enhanced plating on aluminum treated with steel particles. This study investigates the effectiveness of FPP as a pretreatment for nickel electroplating by examining initial deposition behavior. A1050-H24 aluminum was treated using FPP with either steel or glass particles, compared to an untreated specimen. Steel particle FPP created a lamellar microstructure with alternating iron and aluminum phases. EBSD revealed that …

Effects Of Laser Peening On Fatigue Properties Of Welded Aluminum Thin Plates, Kiyotaka Masaki, Yoshio Mizuta, Satoshi Tamaki, Yuji Sano

15th International Conference on Shot Peening

To improve the fatigue properties of welded aluminum alloy thin plates used in transportation machinery, handheld laser peening (HH-LP) was applied to 2 mm-thick A5083-O specimens prepared by bead-on TIG welding. Conventional laser peening often causes warping in thin plates, but the HH-LP treatment using low-energy laser pulses avoids this problem. The HH-LP treatment introduced compressive residual stresses of over 200 MPa on the heat-affected zone (HAZ) of the welded specimens. Fatigue tests under plane bending conditions revealed that the HH-LP treatment significantly improved the fatigue strength of the welded specimens, achieving a level comparable to that of the base …

Microstructural Changes And Residual Stress Generation On The Periodically Patterned Surface Texture Fabricated By Angled Fine Particle Peening, Yutaka Kameyama, Hideaki Sato, Ryokichi Shimpo

15th International Conference on Shot Peening

Focusing on the potential of peening technology as a surface texturing technique, angled fine particle peening (angled-FPP) has been proposed to fabricate a specific periodical surface structure, which possibly provides various surface functions. It is necessary to further characterize the textured surface to earn more advantages from angled-FPP. Thus, in this paper, texture formation phenomena, residual stress, and microstructural changes were investigated on the angled-FPP specimens.

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

Recent Progress And Scientific Challenges In Wire-Arc Additive Manufacturing Of Metallic Multi-Material Structures, Sainand M. Jadhav, Sambhaji Kusekar, Akash Belure, Satyavan Digole, Abhijeet Mali, Muralimohan Cheepu, Manoj Mugale, Suhas Alkunte, Duckbong Kim

Faculty Articles

Metallic multi-material structures are heterogeneous structures characterized by changing composition, microstructures, and site-specific characteristics, advantageous for numerous applications where multifunctionality is desired. Metallic multi-material structures are known as bimetallic structures (BSs), which are functionally graded materials (FGMs). In recent years, wire-arc additive manufacturing (WAAM) advanced as a promising additive manufacturing process to realize the fabrication of these structures due to its high deposition rate, cost-effectiveness, and material utilization efficiency. This review presents a comprehensive overview of the recent progress, processing strategies, and scientific challenges in WAAM of multi-material structures. The paper begins with an introduction to multi-material structures, followed by …

Material Extrusion 3d Printing Of Metal Alloy: Material, Methods And Application., Sihan Zhang

Electronic Theses and Dissertations

Material extrusion (MEX) additive manufacturing presents a promising pathway for producing metal components with complex geometries while avoiding the safety hazards associated with loose powder handling in conventional metal additive manufacturing processes. This dissertation investigates the development and optimization of MEX processes for aluminum alloys, addressing critical challenges in feedstock formulation, printing parameter optimization, and post-processing strategies. Three distinct approaches were explored to advance the capabilities of aluminum MEX: filament-based processing of 6061 aluminum, paste-based extrusion of 6061 aluminum, and development of a novel aluminum-magnesium-tin alloy system for space manufacturing applications. The filament-based approach successfully demonstrated the production of 6061 …

Comparative Study Of Experimental And Fea Strain Data For Cnt-Coated Fiberglass Sensors, Extensometers, And Metal Foil Strain Gauges, Omar Dwidar

Master's Theses

Material testing is essential across industries such as aerospace, automotive, and construction, playing a critical role in verifying material selection, diagnosing failures, and understanding the development of flaws in structures. These insights are key to designing successful, reliable systems. Conventional metal foil strain gauges are low cost and reliable but provide limited sensitivity with a typical gauge factor around 2. Extensometers provide highly sensitive strain measurements with the disadvantage of a bulky form factor. With advanced materials such as carbon nanotubes, it is possible to manufacture a sensor with the sensitivity closer to that of an extensometer with the small …

Effect Of Manufacturing And Machining Process On Recycled Composite Connecting Rods Under Tension And Compression, Walter W. Oppelt

Master's Theses

Carbon fiber reinforced polymer (CFRP) is an engineering material renowned for its high-strength and low-density material properties. Such properties make CFRPs especially useful for applications across many industries, including aerospace, automotive, marine, sporting goods, oil and gas, and more. However, with such favorable material properties comes the cost of high energy usage required to produce raw carbon fiber. Recycled carbon fiber (rCF) has emerged as a promising alternative, offering a significant reduction in energy usage. This research explores the viability of applying recycled CFRPs to internal combustion engines to both reduce energy costs during manufacturing and while in use. Mechanical …

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

Adjustable Dynamometer Motor Mount, Garrett Carson Ng, Elijah Siegel Reuven, Ethan Fong, Daniel Larimer

Mechanical Engineering

The Cal Poly Electrical Engineering Department and sponsor Dr. Dolan needs a manufacturable motor fixture that securely aligns motors of various sizes with dynamometers. Previous lab motor fixtures could not accommodate motors of different sizes, making precise alignment between motors and dynamometers time-consuming and unreliable. Our team developed a modular, manufacturable fixture capable of aligning various motor sizes quickly, accurately, and securely, enhancing lab consistency and usability.

Advanced Manufacturing Of Multifunctional Shape Memory Polymer Composites And Self-Healing Systems, John B. Konlan

LSU Doctoral Dissertations

The need for multifunctional light weight structures for engineering applications is on the rise. Multifunctional composites are desired because of their ability to combine multiple functionalities into one structure. The advantages of a high strength-to-weight ratio of multifunctional composites make them desirable and suitable for use in energy-efficient applications. Shape-memory polymers (SMPs) have attracted interest over the past several decades because of their multifunctional nature. They have found use in many applications such as aerospace, satellites, automobiles, textiles, and biomedical devices, where lightweight and multifunctionality are key. The self-healing nature of most SMPs makes them suitable for use in lightweight …

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Design And Development Of A Rapid Tensile Quench Rig, Tyler Jewell, Justin Naylor

Williams Honors College, Honors Research Projects

This report outlines the design process and implantation of a tensile quenching rig that incorporated forced convection and a frequency generator. When any metal is quenched, a vapor barrier forms around it. When this happens, it limits the heat flux that may occur until the barrier turns into just nucleate boiling. The vapor barrier acts as an insulator and causes the heat flux to fluctuate, causing uneven hardening which would limit the use of some materials. To combat this effect, we are trying to use forced convection, and something new, which is adding high frequency waves into the quenching process. …

Characterization Of The Solid-State Bonding For Simulated Charge And Seam Welds In The Porthole Die Extrusion Process, Randall L. Bowers

Theses and Dissertations--Chemical and Materials Engineering

The isothermal (ISO-T) compression configuration is ideal for utilizing as a material input of flow stress at temperature and strain rate in models of the porthole die extrusion process due to the isothermal nature of the test. Micro-tensile testing was conducted to validate the solid-state welding integrity of the ISO-T samples at various temperatures and strain rates. Results of the mechanical testing were correlated with fractography and microstructural evaluations of the welds to confirm bonding behavior. Both clean interface conditions and oxidation and lubrication layers were evaluated to simulate the difference of seam and charge welds in the process. Results …

Pulsed Arc Additive Manufacturing Of A Functionally Graded Er2209 Duplex Stainless Steel And Hsla-100 Structure: Morphology, Characterization, And Mechanical Performance, Stevens G. Hill Jr

College of Graduate Studies: Theses & Dissertations

Wire arc additive manufacturing is a process well suited to the efficient production of large structures. Duplex stainless steel exhibits high corrosion resistance and good strength which can be highly beneficial for industrial use. However, its use is limited due to its cost and complexity in controlling microstructure to achieve desired properties. In many cases, it can be highly beneficial to manufacture a component which uses specialty steel grades such as duplex stainless steel only where necessary, and utilizes more affordable, commonly available steels for reinforcement or bulk structural support. A functionally graded material satisfies these requirements by providing a …

Neural Operator And Physics-Informed Deep Learning Approaches For Inverse Design Of Composites And Manufacturing Processes, Minglei Lu

All Dissertations

In this dissertation, artificial intelligence (AI) models are designed and used to accelerate inverse design of composites and manufacturing processes. The critical bottlenecks in machine learning (ML) including data availability, data quality, model generalization and adaptation, interpretability, physical consistency, and the ’black box’ nature of models for the inverse design are addressed. And the proposed AI models are tested under different engineering scenarios. Firstly, a fast deep neural operator (DNO) structure was developed to significantly reduce training time. This model was tested in the context of additive manufacturing, a transformative industrial technology that allows for the creation of materials with …