Manufacturing Commons^™

Comparison Of Peening Effect Between Additive Manufacutred And Drawing Titanium Alloy, Hitoshi Soyama

15th International Conference on Shot Peening

Although additively manufactured (AM) metals are attractive materials, their remarkable weak fatigue properties are an obstacle to their practical application. Thus, post-processing to improve their fatigue properties is required. In the present study, powder bed fusion using laser sintering titanium alloy, i.e., PBF-LS/Ti6Al4V was treated by shot peening (SP), submerged laser peening (SLP), cavitation peening (CP), and fine particle bombarding (FPB), then the fatigue properties were investigated by a torsional fatigue test, comparing with drawing Ti6Al4V. It was revealed that the fatigue strength at 10⁷ was 446 ± 5 MPa for PBF-LS/Ti6Al4V treated by FPB+CP, 359 ± 9 MPa …

Integrated Compliant Structure For A Hand Exoskeleton, Tristan R. Koopman

Honors Undergraduate Theses

This thesis presents the design and prototyping of a wearable hand exoskeleton that integrates a flexible structural framework to assist with hand movement while maintaining comfort and anatomical conformity. The goal was to create a device that supports tendon-driven actuation through a compliant structure, combining elements of rigidity and flexibility to match the natural geometry and motion of the human hand. Traditional hand exoskeletons often trade off motion for structure or vice versa. This project aims to bridge that gap with a hybrid compliant design that balances flexibility and support. The design process followed an iterative approach involving rapid prototyping …

Investigation Using Single Point Incremental Forming (Spif) To Fabricate Patient-Specific, Titanium Orbital Floor Implants, Elizabeth M. Mamros, Lauren E. Blaha Md, Christian A. Kauffman Md

Faculty Conference Papers and Presentations

The floor of the human orbit is composed of thin bone that is prone to traumatic fracture. This leads to a loss of support for the eye, which can cause vision changes. Therefore, fractures may need surgical reconstruction using a thin, sheet-like implant. Titanium implants are available off-the-shelf in standard sizes, but fitting to each patient’s unique anatomy requires surgeons to cut, file, and bend these plates. This can be time-consuming and imprecise. To both save time and ensure a perfect fit for the patient, a custom plate can be created prior to surgery. This investigation focuses on single-point incremental …

Enhancing The Mechanical Properties Of Sla 3d-Printed Bio-Resin From Linseed Oil Using Cellulose And Lignin Biopolymers, Chukwunonso A. Ikedionu

College of Graduate Studies: Theses & Dissertations

Abstract

This research explores the development of bio resin from linseed oil by the process of epoxidation and acrylation to produce acrylated epoxidized linseed oil (AELO). Lignin and cellulose biopolymers were added as reinforcement at varying weight fractions of 1 wt.%, 2.5 wt.%, and 5 wt.%, and their mechanical performance was compared against pure AELO. The formulations were printed using an Elegoo SLA 3D printer to create standardized test specimens like tensile bars, compression cylinders, and hardness blocks, which were all prepared according to the ASTM testing standard.

The results indicate that reinforcement effects depend on both filler type and …

Investigation Of Distributed Additive Manufacturing For 3d Printed Headband Component During Global Supply Chain Disruptions, Elizabeth M. Mamros, Saketh Kantipudi, Matthew C. Eaton, Jinjin Ha, Brad L. Kinsey

Faculty Conference Papers and Presentations

During the COVID-19 global pandemic, a shortage of personal protective equipment (PPE) occurred. Manufacturers of these critical products were unable to keep up with the growing demands as the situation evolved. Most face shields, a common type of PPE, include a headband component to provide the appropriate fit for the user and curvature for the clear face shield attachment. To mitigate this shortage in the local region, the Portsmouth Naval Shipyard (PNSY) generated a computeraided design (CAD) file for the headband component and asked the University of New Hampshire (UNH) to manufacture it with all available 3D printers, including printers …

Shape Memory Alloy Capsule Micropump For Drug Delivery Applications, Youssef Mohamed Kotb

Theses and Dissertations

Implantable drug delivery devices have many benefits over traditional drug administration techniques and have attracted a lot of attention in recent years. By delivering the medication directly to the tissue, they enable the use of larger localized concentrations, enhancing the efficacy of the treatment. Passive-release drug delivery systems, one of the various ways to provide medication, are great inventions. However, they cannot dispense the medication on demand since they are nonprogrammable. Therefore, active actuators are more advantageous in delivery applications. Smart material actuators, however, have greatly increased in popularity for manufacturing wearable and implantable micropumps due to their high energy …

Liftwalker, Kai A. De La Cruz, Lexie Caterine, Adam Monroe, Jame Whealan

Mechanical Engineering

The LiftWalker’s purpose is to lift users with degenerative diseases from a seated to standing position and support them as they practice the motion of walking as a form of physical therapy. The current LiftWalker is upward of $5,000 so we redesigned the LiftWalker to be more accessible around the world. This meant using affordable and accessible materials and manufacturing processes. To achieve this, we made our design mostly out of bike parts and off-the-shelf components. When it came to the lift system, we found that to maintain a safe and comfortable design it was best to purchase a trailer …

The Interaction Of The Cotton Piece With The Piles Of The Scrabble Cotton Drum, Fazliddin Egamberdiev, Ilkhom Abbazov, Oybek Kholmuratov, Rashid Kaldybaev

Technical science and innovation

This article presents the results of an analytical study of the process of loosening and cleaning raw cotton from small debris by pileging working bodies of purifiers, on the basis of which directions for further research were chosen to optimize the parameters of the developed pile drum with spherical piles and rubber strips. Cotton entering production contains impurities. The processes of loosening and cleaning the fiber shreds are key in the initial stages of ginning, as they prepare the raw cotton for ginning and directly affect the reliability, productivity of these processes and the quality of the resulting fiber. Weed …

Fungi In Flux | Designing Regenerative Materials And Products With Mycelium, Arvind Bhallamudi

Masters Theses

As the world grapples with the escalating crisis of climate threats and environmental degradation, this research delves into the synergistic potential of design and biology, developing safe and sustainable materials for applications in prototyping, furniture and interior design. Harnessing the power of a unique organism - fungi, the study proposes an accessible, efficient, and resilient material resource system. It utilizes local waste streams and mycelium (the vegetative part of fungi) to grow functional structures. An experimental and small-scale protocol is modeled by testing bio-fabrication and bio-printing methods. The composites' performance qualities and characteristics are evaluated through mechanical testing and a …

Advanced Microstructural Characterization Of Functionally Graded Dental Ceramic Material For Materials-Informed Finishing, Angani Vigneswaran

Theses and Dissertations--Manufacturing Systems Engineering

Yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) has gained popularity as the choice of material for dental prosthetics. Ivoclar Vivadent’s IPS e.max ZirCAD Prime dental ceramic incorporates a unique gradient technology that varies the yttria content over the thickness of the material. The top layer is composed of 5Y-TZP which is desired for its optical properties while the bottom layer is composed of a much stronger 3Y-TZP. In between the two layers, 5Y-TZP and 3Y-TZP are mixed to form a transition layer. Varying the amount of yttria allows for more esthetically pleasing translucency in the visible areas of the restoration without compromising …

Full Body Harness Design Modifications And Evaluation: A Senior Design Project, Martin Mead, Jordan Von Seggern

The Journal of Undergraduate Research

Full-body harness (FBH) is critical for the safe operation of industrial and recreational activities, from installing and maintaining infrastructure such as wind turbines to ziplining and mountaintop adventures. However, harness design remains in the proprietary information of companies with limited technical information available for improvements or readjustments to specialized applications. As the outcome of the Capstone project, the paper focuses on multiple technical aspects and the engineering processes for designing FBH for ziplining recreational users, from selecting and testing materials for operation in cold weather to improvements in design and manufacturing for user comfort. The project is guided by technical …

Studying And Troubleshooting Lubricity Test On Pressure Wire X Proximal And Distal Coatings, Usama A. Khan

All Graduate Theses, Dissertations, and Other Capstone Projects

Coatings of guidewires used in medical device manufacturing industry are one of the most important element aspects. It defines its efficiency to penetrate through tightest of canals and curves. Guidewires are put through controlled environment to accelerate its age and tested for its mechanical features. Pressure Wire X failed the lubricity testing after being tested by multiple operators and at alternate sites. A cause-and-effect diagram shows all potential causes of test failure. The human factor involved in the test failure was investigated through multiple Gage R&R and training records. Calibration error with the lubricity tester DL1000 was identified and solved …

An Experimental Study On The Mechanical Properties And Chemical Composition Of Lcd 3d Printed Specimens, Sebastian Gomez

College of Graduate Studies: Theses & Dissertations

Additive manufacturing technologies have been enhanced throughout the years yet have surprised the manufacturing industry due to their high-end surface finish and dimensional accuracy. Different experiments have been done to identify a specific phenomenon known in the vat-polymerization field. Distortion and dimensional inaccuracy tend to affect the overall properties of the process, either physical or chemical. This approach allows the understanding of how the physical properties have been affected and how to study the chemical properties to avoid this type of phenomenon. The chemical reaction between polymer and UV light has been studied and experimented with to the point that …

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

College of Graduate Studies: Theses & Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

Material Characterization Of Thermoplastic Polyurethane (Tpu) And Thermoplastic Elastomers (Tpe) For Development Of 3d-Printed Surrogate Organs For Medical Training, Anastasia Elizabeth Lucci

Graduate Theses, Dissertations, and Problem Reports (ETD)

Cadaveric specimens are a necessary, albeit limited, resource for training medical students on basic surgical skills. The availability of surrogate 3D-printed organs would readily allow access to resources that could reduce or potentially eliminate the need for cadaveric specimens or, at a minimum, provide students the opportunity to practice with 3D-printed surrogates before transitioning to those specimens. This research focuses on determining which thermoplastic material most closely mimics mechanical properties such as hardness and stiffness of human organs and allows 3D printing surrogate organs to be used as safe, educational tools. Relatively “soft” materials such as thermoplastic polyurethanes (TPU) and …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Biomedical Engineering: Graduate Reports and Projects

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Master's Theses

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Eagle Medical Tray Denesting & Debris Removal Process, Nicholas Allen Ungefug, Noah Chavez, Susana Shu-Lin Okhuysen, Michael Augustine Pennington

Industrial and Manufacturing Engineering

Eagle Medical Incorporated is a contract medical device packaging and sterilization company. The company purchases thermoformed medical packaging trays, which maintain the sterility of medical devices, from various manufacturers. To ensure packaging quality and to prevent cleanroom contamination, Eagle Medical inspects and sterilizes each blister tray that they order. This process is an essential non-value-added activity that creates a bottleneck. Cleanroom employees must stop packaging medical devices and attend to the processing of blister trays and packaging solutions. The blister trays arrive at Eagle’s facility in nested stacks. Vibration and movement during shipping further compresses the stacks, which makes separation …

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

LSU New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Poly(2-Hydroxyethyl Methacrylate) Hydrogels For Contact Lens Applications–A Review, Kushendarsyah Saptaji, Nurlaely Rohmatul Iza, Sinta Widianingrum, Vania Katherine Mulia, Iwan Setiawan

Makara Journal of Science

The emerging technology in biomedical engineering requires biocompatible materials, which are also referred to as biomaterials. For a material to be considered biocompatible, it should not interact with human tissues in a harmful way, and vice versa. Various properties of biocompatible materials, such as mechanical and optical properties, have to be considered for different biomedical applications. One of the most popular applications of biomaterials is for contact lenses. Hydrogels, specifically poly(2-hydroxyethyl methacrylate) (PHEMA) hydrogels, are among the most popular ones in ophthalmologic applications, especially in soft contact lenses. This paper reviews the use of PHEMA hydrogels as one of the …

Printing Quality Improvement For Laser-Induced Forward Transfer Bioprinting: Numerical Modeling And Experimental Validation, Jie Qu, Chaoran Dou, Ben Xu, Jianzhi Li, Zhonghao Rao, Andrew Tsin

Manufacturing & Industrial Engineering Faculty Publications

Laser-induced-forward-transfer (LIFT)-based laser assisted bioprinting (LAB) has great advantages over other three-dimensional (3D) bioprinting techniques, such as none-contact, free of clogging, high precision, and good compatibility. In a typical LIFT based LAB process, a jet flow transfers the bioink from the ribbon to the substrate due to bioink bubble generation and collapse, and the printing quality is highly dependent on the jet flow regime (stable or unstable), so it is a great challenge to understand the connection between the jet flow and the printing outcomes. To tackle this challenge, a novel computational-fluid-dynamics (CFD)-based model was developed in this study to …

Tailoring Texture, Microstructure, And Shape Memory Behavior Of Niti Alloys Fabricated By L-Pbf-Am, Sayed Ehsan Saghaian N.E.

Theses and Dissertations--Mechanical and Aerospace Engineering

Laser Powder Bed Fusion (L-PBF) is one of the most promising Additive Manufacturing (AM) methods to fabricate near net-shape metallic materials for a wide range of applications such as patient-specific medical devices, functionally graded materials, and complex structures. NiTi shape memory alloys (SMAs) are of great interest due to a combination of unique features, such as superelasticity, shape memory effect, high ductility, work output, corrosion resistance, and biocompatibility that could be employed in many applications in automotive, aerospace, and biomedical industries. Due to the difficulties with traditional machining and forming of NiTi components, the ability to fabricate complex parts, tailor …

Additive Manufacturing In Personalized Medicine: Patient-Customized Solid Dose Medicines, And Patient-Customized Wound Care Device, Amir Najarzadeh

Theses and Dissertations--Mechanical and Aerospace Engineering

Personalized Medicine - from a one-size fits all to a tailored approach is the future in pharmaceutical therapeutics and medical applications. The aim of this study is demonstrate additive manufacturing in two personalized medicine applications: 1. Patient- customized solid dose medicines, and 2. Patient-customized wound care device. The aim of the first application is to develop an inexpensive and accurate method to design and fabricate patient-customized tablets. Particularly this paper focuses on fabricating and dose controlling of patient-customized extended release prednisolone-poly(vinyle alcohole) PVA. Dry-Blending, Wet Granulation, Extrusion, Spherionization, Hot melt extrusion (HME) was adopted to produce drug loaded prednisolone-PVA filaments …

An Affordable And Portable Palpable System For Sensing Breast Tissue Abnormalities, Cody J. Clarke

Montview Journal of Research & Scholarship

Due to the high cost of equipment and lack of trained personnel, manual palpation is a preferred alternative breast examination technique over mammography. The process involves a thorough search pattern using trained fingers and applying adequate pressure, with the objective of identifying solid masses from the surrounding breast tissue. However, palpation requires skills that must be obtained through adequate training in order to ensure proper diagnosis. Consequently, palpation performance and reporting techniques have been inconsistent. Automating the palpation technique would optimize the performance of self-breast examination, optimize clinical breast examinations (CBE), and enable the visualization of breast abnormalities as well …

Prosthetic Foot Shell, Ql+, Kathryn Victoria Versteeg, Jackson A. Tucker, Ethan William Frey

Mechanical Engineering

This final design review includes an overview of our project and the steps we have taken to create our final product. We discuss the background research conducted, including various products like the foot shell we are trying to design and its related patents, along with similar past senior projects. As our product is considered a medical device, there are also certain standards that we must comply with. After determining our problem statement, we established what we believe to be the wants and needs of our user. These wants and needs were converted into specifications for our design, with durability as …

Tmtt Chimera Valve Attachment Process, Paulina Nguyen, Devin Debouk, Tamar Kazazian, Noah Thompson

Biomedical Engineering

No abstract provided.

Development Of A Single Use Device Intended To Wash Blood Clot Debris From A Stent Retriever In The Operating Room, Shane Diller

Theses and Dissertations

Ischemic stroke is a life-threatening condition that requires immediate surgical intervention to remove the blood clot that is lodged in the blood vessels of the brain. Mechanical thrombectomy, performed by an endovascular surgeon, involves inserting a stent retriever, which deploys distally and attempts to capture the clot when dragged backwards. A complication prevalent in 50% - 67% of cases is that the blood clot is only partially removed and clings to the mesh framework of the stent. The operating surgeon must either clean the debris from the stent retriever, to be reinserted or throw the stent retriever away and open …

3d Printing Of Iron Oxide Incorporated Polydimethylsiloxane Soft Magnetic Actuator, Rasoul Bayaniahangar

Dissertations, Master's Theses and Master's Reports

Soft actuators have grown to be a topic of great scientific interest recently. As the fabrication of soft actuators with conventional microfabrication methods are tedious, expensive, and time consuming, employment of 3-D printing fabrication methods appears promising as they can simplify fabrication and reduce the production cost. Complex structures can be fabricated with 3-D printing such as helical coils can achieve actuation performances that otherwise would not be possible with simpler geometries. In this thesis development of soft magnetic helical coil actuators of iron-oxide embedded polydimethylsiloxane (PDMS) was achieved with embedded 3-D printing techniques. Composites with three different weight ratios …

System Integration Of C-Arm Robotic Prototype Using Motion Capture Guidance For Accurate Repositioning, Alireza Yazdanshenas

Mechanical Engineering Theses

One of the important surgical tools in spinal surgery is the C-Arm X-ray System. The C-Arm is a large “C” shaped and manually maneuvered arm that provides surgeons and X-ray technicians the ability to take quick quality X-rays during surgery. Because of its five degrees of freedom, the C-Arm can be manually maneuvered around the patient to provide many angles and perspectives, ensuring surgical success.

This system works fine for most surgical procedures but falls short when the C-Arm must be moved out of the way for complicated surgical procedures.

The aim of this thesis is to develop an accurate …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …