Manufacturing Commons^™

Sustainable Phone Housing, Jonah Milnor

All Undergraduate Projects

Most commercially available smartphones posed a challenge to consumers due to the use of adhesives, which not only served to seal out dust and water but also hindered repairability and hardware replacement. Drawing inspiration from successful smartwatch designs employing gaskets for water resistance, this project aimed to adapt such design principles to the smartphone form factor.

Utilizing SolidWorks for design and subsequent 3D printing and CNC machining for prototyping, 3D models of a smartphone housing were crafted. The objective was to attain a level of water and dust resistance equivalent to that of model smartphones, utilizing sealing methods equivalent to …

Balsa Bridge, Caleb T. Lovett

All Undergraduate Projects

The problem presented throughout this report was to create a small-scale bridge made entirely out of balsa wood and glue, that could withstand substantial force, as well as perform a lifting/lowering cycle. Other requirements associated with the bridge were properties of weight, deflection, size, and shape. This problem presented a challenge that tested the mathematical side of engineering, being strongly reliant on statics, mechanics of materials, and mechanical design analyses.

To approach this problem, the first step was to complete in depth calculations of the chosen design. With this done, manufacturing and assembly was able to be completed. With a …

Rc Baja: Drivetrain And Chassis, Caden Harris

All Undergraduate Projects

The engineers in the CWU Mechanical Engineering Technology program were asked to design and manufacture a remote-controlled Baja car to compete in several different events. The car was required to compete in a drag race, slalom event, and Baja event against other cars created by engineering students. To compete at the highest level, the cars needed to finely balance ruggedness, weight, torque, and top speed.

This report is dedicated to the designing, manufacturing, and testing of the drivetrain and chassis that supported the RC car as it competed in the school-sanctioned competition; a partner was responsible for the steering and …

Articulating Balsa Wood Bridge, Nate Harris

All Undergraduate Projects

This report describes the design, construction, and testing of a small-scale articulating balsa wood bridge that allowed passage over normally impassable terrain. The bridge was required to span a 400mm gap, while also articulating the midpoint of the bridge 140mm above its resting position. The bridge also needed to support a 20kg (44 lbs.) point load in the center of the bridge, and the bridge and articulation tower together needed to weigh less than 85 (0.19 lbs.) grams.

To construct the bridge, statics and mechanics of materials was used to design a truss that was calculated to support the load …

Combat Robot, Riley Buxton

All Undergraduate Projects

In the sport of combat robotics, the goal is to build a robot that can incapacitate an opposing robot before it becomes incapacitated itself. For this project, a combat robot was designed and tested to compete in Western Allied Robotics’ first competition at Central Washington University. The robot was built to compete in the beetle weight class which means the entire robot had to weigh less than 3 lbs.

To ensure the robot was competitive, a number of important design choices were made. Firstly, an effort was made to ensure that the design was simple and easy to take apart …

Jack And Alex Rc-Baja, Alex Vornbrock

All Undergraduate Projects

Teams of two mechanical engineering students were tasked with the construction of an RC Baja car qualified by the rules and regulations of the Baja competition as well as specifications set by the individual team member for their portion of the vehicle. This proposal focuses on the Chassis and Drivetrain of the vehicle while team member Jack Stutz oversaw the steering and suspension. Teams will compete against each other in various modes to determine the best vehicles of the competitors. The chassis was made of standard aluminum, the remaining parts made by the students were made with PLA; both materials …

Rc Baja Suspension And Steering, Garrett Bailey

All Undergraduate Projects

The RC Baja team set out to engineer and construct a working remote-control device that can compete in the ASME Baja Competition. The students have a focus on either suspension and steering or drivetrain and chassis. This report is centered on the suspension and steering. First, multiple analyses were completed using engineering methods such as mechanical design, statics, strengths of materials, and dynamics for parts of the device. The calculations found in the analysis are then used to create designs for the parts so that they will meet the requirements and be successful in the competition. After the parts are …

Rc Baja 2023 Drivetrain And Chassis, Nathan Norby

All Undergraduate Projects

Students’ objective this quarter was to design a remote-controlled vehicle that utilizes a 4-link rear suspension, an I-beam front suspension, the ability to withstand a substantial front impact and several gearing options. The team also used several agreed upon design requirements to quantify the results of the objective.

To meet these objectives students followed a strict engineering method. Students split into a team’s divided the work into two sections. Max was responsible for the suspension and steering and Nathan was responsible for the chassis and drivetrain. Methods included engineering analysis which used mechanics of materials, static analysis, dynamic analysis, and …

Rc Baja Project: Suspension And Steering, Chance Hills

All Undergraduate Projects

Students designed and manufactured an RC Baja car to compete in the ASME RC Baja competition. The goal of this section of the project was to create a steering system and suspension system that work together properly with a partner’s chassis/drive train systems during tests and competitions. The car needed to be able to complete in the three events, which are a drag race, a solemn course, and the Baja event. The RC will also be evaluated on the ability to climb inclines, top speed, and withstand the drop test. This proposal will explain all the details and effort that …

Jcati Carbon Fiber Recycler: Crusher System, Devin Riley

All Undergraduate Projects

With a substantial rise in Carbon Fiber use across all industries, the need for a way to recycle the waste has grown as well. A group of Mechanical Engineering Technology students at Central Washington University funded by the Joint Center for Aerospace Technology (JCATI) have created a machine to recycle waste wing trimmings from the Boeing company’s airplanes. This machine consists of 5 different sub-assemblies being the oven, crusher, gear train, conveyor, and shredder. The purpose of this project was to decrease the deflection in the crusher caused by bulging in the housing and movement of the bearings. To decrease …

R/C Baja: Drivetrain, Connor T. Donovan

All Undergraduate Projects

The Central Washington University Mechanical Engineering Technology Department hosts an annual R/C Baja competition in which R/C cars fabricated by student teams are put through a series of courses and tests to determine which team's vehicle is best. The goal of this project was to create a functioning drivetrain that conveys power from the battery to the wheels and provides control of the vehicle. A list of requirements for the drivetrain was created to ensure that the vehicle will not only function, but that it will actually succeed in the competition. These requirements included that the vehicle must achieve a …

Team H&H Rc Baja Drivetrain, William T. Hedlund

All Undergraduate Projects

A need for a drivetrain and steering system that could provide locomotion and directional control for the H&H RC Baja racecar was needed. The RC Baja event is a competition hosted by the CWU ASME club in which teams of engineering students compete against each other to test the effectiveness of the respective designs. The car needed to be able to compete in three events: a drag race, solemn course, and a Baja event. This was accomplished by designing and manufacturing several parts of different materials utilizing a range of manufacturing techniques to produce sub-assemblies and that made up the …

Carbon Fiber Recycling: Delamination System, Aaron Eastman

All Undergraduate Projects

The production of composite wings at Boeing causes carbon fiber waste and CWU Mechanical Engineering Technology students have been tasked in designing a carbon fiber recycling system. This project was brought forth and funded by the Joint Center for Aerospace Technology Innovation (JCATI). There are three subsystems that make up the carbon fiber recycling system, the delamination system, shredding system, and the oven. The purpose of this project was to increase the efficiency and effectiveness of the delamination system of the carbon fiber recycling system. The old system reached approximately 30-40 percent delamination with one pass through the system, and …

Jcati Carbon Fiber Shredder 2022, Parker Sudderth

All Undergraduate Projects

This project is a potential solution to keep the carbon fiber waste from airplane manufacturing to a minimum, sponsored by the Joint Center for Aerospace Technology Innovation (JCATI). The design and assembly will be scalable for future industry application. The overall design of the whole carbon fiber recycler consists of a crusher, shredder, and oven. This report is on the caron fiber shredder module. The shredder is tasked with being able to shred the delaminated carbon fiber scrap that directly comes from the crusher. The operation must produce shreds in the proper size to be gathered and delivered to the …

Rc Baja: Drivetrain And Steering, Mathew Morgan

All Undergraduate Projects

The RC Baja competition is a contest where undergraduate mechanical engineering students design, build, and compete against one another. The objective of this competition is to create the most efficient RC car possible. A gear train analysis was done and showed an 8:1 gear ratio would be the most efficient ratio due to the chosen motor having a higher torque output. Also, a stress analysis was done and showed that 2011 T3 aluminum passed the stress and weight criteria. These analyses ensured the RC Baja car was efficient. Most of the parts for the drivetrain and steering subassemblies were machined …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

R/C Baja Truck Suspension, Chassis And Steering, Ryan Lafrombois

All Undergraduate Projects

The ASME RC Baja Challenge is an annual competition that the Central Washington University Mechanical Engineering and Technology (MET) department takes part in. Senior level engineers divided the work between the drivetrain and the chassis/suspension while designing and manufacturing to meet a set of requirements. Next, a device was to be developed to be able to withstand the extreme forces to be successful in the competition at the end of the year. The process would require that the students use their acquired knowledge and skills to design, manufacture, and analyze a capable device. Designing involved the completion of 12 analyses …

Asme Rc Baja Racer, Chesna Kern

All Undergraduate Projects

The American Society of Mechanical Engineers (ASME) holds a competition at their annual conference for college students to design an RC car that will compete in sprint, slalom, and obstacle course races. The RC Baja car was designed to complete every event in the competition with a focus on the obstacle course due to the anticipated impacts inflicted on the project car by jumps and other obstacles. The project was a collaborative effort. This presentation focuses on the chassis and suspension while Gizan Gando will present about the drivetrain. The drop and frontal impact test requirements guided the design process …

Jcati Base Plate, Jacob Atamian

All Undergraduate Projects

Students of the Mechanical Engineering Technology (MET) program at Central Washington University have contributed to an ongoing Carbon Fiber Recycler project funded by the Joint Center for Aerospace Technology Innovation (JCATI). The goal of this project was to modify the existing recycling system to produce a higher success rate of recycled carbon composite material. This report focuses on increasing the rigidity of the crushing gears so that the deflection occurring among the components during operation was below 0.005 inches to ensure proper operating conditions. The operating speed of the crushing gears was 2.5 rpm with a crushing load of 10,500 …

Balsa Wood Bridge, Anndie Watterson

All Undergraduate Projects

A model for a strong bridge that could span a set distance and rise up to allow for passage underneath was requested, and specifications for the design were given. The model bridge was designed out of balsa wood to meet all the requirements. Using structural and material analysis and simple mechanical designs, a bridge was designed and constructed out of balsa wood, wood glue, and metal components used for articulation that met all of the criteria set by the assigner. The bridge was tested to ensure all specifications were met. The resulting bridge can hold 20kg of weight suspended from …

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Asme Rc Baja Car Drivetrain, Gizan G. Gando

All Undergraduate Projects

The purpose of the RC Baja Car is to compete in the American Society of Mechanical Engineers (ASME) competition, a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race. The Slalom is a test in the steering capability of the car. The Drag is a test in the acceleration of the car in a straight line. Lastly, the Baja puts all factors together in a race to test every component of the car. This project is about building an RC car that can function under these conditions and …

Asts Frame, Dustin Braun

All Undergraduate Projects

The automotive industry has been an industry of many breakthroughs in technology and mechanical systems over the course of its history. But in one area, its innovation has slowed. That is in the area of the short throw shifter. All aftermarket short throw shifters are currently one dimensional. No adjustability, no ability to finetune to one’s personal desire. The goal of this project is to create a short throw shifter frame that is easier/faster to install, as well as allow for full adjustability of the shifter from inside the car. This frame design uses mostly 6061-T6 aluminum, along with some …

Speed Bump Power Generator, Sultan Alanazi, Osamah Abulgaith

All Undergraduate Projects

A large amount of energy is wasted by the vehicles on the speed breakers through friction. Energy can be produced by using the vehicle weight and speed. The team proposes a smart speed breaker that generates power (Speed bump power generator). The device allows vehicles to pass from both sides. The system makes use of mechanical assembly with metal sheets with linkages that press down with spring arrangement. Using the motion and weight of vehicles was the method that the team relied on to design the device. The mass of the vehicles allows the top plate to move the rack …

Composite Guitar, Ryn Rollins

All Undergraduate Projects

Traditional wood-bodied products such as boats, hockey sticks, and guitars can be easily chipped or cracked if not properly taken care of. The wood can absorb moisture and deteriorate over time. If that wood is replaced with composite materials, those products can become stronger, more lightweight, and resistant to temperature and corrosion. Two of the most popular composite materials are carbon fiber and fiberglass. Because these composite materials have such a high strength, the core of a guitar body can also be replaced with a lighter material such as Styrofoam which makes for a lighter and more durable guitar. The …

Rc Mini Baja Car - Suspension And Chassis, Collin Mckenzie

All Undergraduate Projects

Two students have developed a unique design of the RC Baja Car to optimize functionality and performance. A Baja car is a remote controlled 1/10 scale car that is used for recreation or competition, usually meant for competing in the ASME Baja car competition versus various schools. The competition focuses on the best time achieved in different courses that utilize speed, turns, and jumps. The objective for the project was to create a unique suspension from previous individual’s projects by creating a four-link suspension in which allows more travel in the suspension of the car and maintains functionality with the …

Next Generation Longboard Trucks Ng-Trucks, Zach J. Ducatt

All Undergraduate Projects

A device is needed that will provide longboard riders with a truck that is specifically designed for the sharp turns and high speeds they experience throughout their ride. This longboard truck must have a design that is engineered for these purposes and avoids the standard pin and bushing design that is commonly copied from the closely related skateboard truck. This standardized design is outdated, and more importantly, was made to adhere to the skateboard style of riding, consisting primarily of performing tricks with less turning. The longboard truck provides a secure connection point upon the two wheels and the board …

Forge Burner, Caleb Desjardins

All Undergraduate Projects

Can small scale blacksmithing operations achieve a level of efficiency in their forge comparable to that of a large scale industry? The causes for the lack of efficiency needed to be pinpointed, and then the geometry of the existing design for the burner could be changed to fix the underlying issues, while still maintaining functionality. The problems with the previous design is the geometry of the intake giving an unknown air/fuel ratio, and the attachment of to the forge allowing the intake air to be contaminated by exhaust gasses. A burner needed to be designed that would solve these problems …