Manufacturing Commons^™

Thermal Characterization Of 3d Printing Materials For Increasing Insulation Potential And Practicality, Jackson H. Minnick

Mechanical Engineering Undergraduate Honors Theses

This study served as an exploration into the possible existence of a correlation between the infill lattice structure of a 3D printed wall section and the thermal performance of that sample as characterized by thermal conductivity measured in units of Watts per meter Kelvin. With the continual increase in the practicality, fidelity, and applicable fields of additive manufacturing, namely FDM 3D printing, research on specific print characteristics and their effects on the material and thermal characteristics of the part in question is steadily becoming more commonplace. Although the thermal conductivity of 3D printed wall sections as a function of infill …

Integrated Compliant Structure For A Hand Exoskeleton, Tristan R. Koopman

Honors Undergraduate Theses

This thesis presents the design and prototyping of a wearable hand exoskeleton that integrates a flexible structural framework to assist with hand movement while maintaining comfort and anatomical conformity. The goal was to create a device that supports tendon-driven actuation through a compliant structure, combining elements of rigidity and flexibility to match the natural geometry and motion of the human hand. Traditional hand exoskeletons often trade off motion for structure or vice versa. This project aims to bridge that gap with a hybrid compliant design that balances flexibility and support. The design process followed an iterative approach involving rapid prototyping …

3d Printing Of A Solid-State Battery, Maurizio A. Brozzi

Honors Undergraduate Theses

Solid-state battery research has gained significant attention in recent years, as it provides a unique solution for several common issues in conventional Li-ion batteries. Additionally, as additive manufacturing technologies continue to advance, they have the potential to fabricate solid-state batteries with new materials. The objective of this study is to explore the feasibility of 3D printing of a solid-state battery. By creating an initial PEO-PSF hybrid polymer matrix dissolved in DMSO and adding a lithium salt, the base electrolyte ink was formed. With the addition of conductive additives and active material, electrode inks were also produced. Super P was used …

Enhancing The Mechanical Properties Of Sla 3d-Printed Bio-Resin From Linseed Oil Using Cellulose And Lignin Biopolymers, Chukwunonso A. Ikedionu

College of Graduate Studies: Theses & Dissertations

Abstract

This research explores the development of bio resin from linseed oil by the process of epoxidation and acrylation to produce acrylated epoxidized linseed oil (AELO). Lignin and cellulose biopolymers were added as reinforcement at varying weight fractions of 1 wt.%, 2.5 wt.%, and 5 wt.%, and their mechanical performance was compared against pure AELO. The formulations were printed using an Elegoo SLA 3D printer to create standardized test specimens like tensile bars, compression cylinders, and hardness blocks, which were all prepared according to the ASTM testing standard.

The results indicate that reinforcement effects depend on both filler type and …

Materials Testing For Large Format 3d Printing, William Jenkins

Williams Honors College, Honors Research Projects

An ABS Carbon Fiber blend was printed into single walled hexagons at a variety of settings on a Cincinnati BAAM large format 3D printer. These hexagons were then cut down into sheets and had tensile and flexural test samples cut out of them, in order for materials testing to be performed. Tensile strength, tensile strain, young’s modulus, flexural strength, deflection and elastic modulus were all determined. A desktop CNC machine and a planer were purchased for the manufacturing of these samples, and an efficient cutting procedure was designed and optimized. After all data collection concluded, this data was thoroughly analyzed, …

3d Printed Drone (Body And Controls), Michael Dick, Hayden Pinkelman, Tanner Henderson, Logan Prince

Williams Honors College, Honors Research Projects

The objective is to build a scaled down model of a 3D printed drone capable of carrying a payload scalable to 50 lbs. for a wide array of applications. Some applications of the drone could include delivering support materials during natural disasters, such as foam to put out fire or medical aid packs to provide aid to injured people, food or package delivery, or military applications. The project has been split up into two groups. One group will be focusing on the propulsion aspect of the project, such as the electric motors and airfoil. Simultaneously, this group will design the …

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Additive Manufacturing For Medical Education, Michael Noon

College of Engineering Summer Undergraduate Research Program

A growing body of evidence is suggesting that anatomical knowledge, the keystone of many medical specialties, is suffering among new graduates. While a host of reasons are provided, one common thread that many point to is the decline of cadaver dissections in the classroom. Many virtual audio-visual tools are used to address this gap, yet evidence has shown their ineffectiveness. Given this gap, the high degree of flexibility found in additive manufacturing (AM), and the many uses AM has already found in the medical field, we propose its use to fill this gap, allowing for students to learn with touch …

Modeling, Control, And Hardware Development Of A Thrust-Vector Coaxial Uav, Andrew North

Doctoral Dissertations and Master's Theses

This thesis introduces a unique thrust vector coaxial unmanned aerial vehicle (UAV) configuration and presents a comprehensive investigation encompassing dynamics modeling, hardware design, and controller development. Using the Newton-Euler method, a dynamic model for the UAV is derived to gain in-depth insights into its fundamental flight characteristics. A simple thrust model is formulated and modified by comparing it with data obtained from vehicle testing. The feasibility of manufacturing such a vehicle is assessed through the development of a hardware prototype. Finally, a linear state feedback controller is designed and evaluated using the non-linear dynamics model. The results demonstrate successful validation …

3d Printed Aircraft, Matthew Nagy, Charles D'Amico, Alexis Salgado Medina

Mechanical Engineering

This project is to design, build, and test a 3D-printable aircraft. The goal is to create a final design that will be able to fly for the longest duration possible, around 20 seconds. To determine the correct preliminary design and manufacturing process for a 3D printed RC aircraft, an analysis of multiple design options and manufacturing materials was performed. This allowed for a variety of choices for aircraft type, airfoil design, structure, among other topics to be narrowed down to the most promising option. It has been found that the aircraft will follow a design similar to industry motor-gliders, with …

Pla-S-Tech: Pla Sustainable Technology, Sean Sapper, Ryan Decarlo, Elle Whitney, Samantha Dombrowski, Dalton Prokop, Dominic Zaio, Tyler Stokes, David Deese, Blake Hengel, Yi Guo

Mechanical and Civil Engineering Student Publications

To recycle waste material produced by fused deposition modeling (FDM) 3D printers, a recycler was designed and manufactured to convert plastic scraps into usable filament. The device does so by breaking down plastic material to a uniform size with the shredder, melting and compressing these pieces into a cylindrical strand with the extruder, and wrapping this strand around a filament spool with the spooler. As the device is mostly made from commercially-available components, it is easily maintainable and user-serviceable, while also costing less than similar devices on the market.

A Machine Learning Approach To Robotic Additive Manufacturing Of Uv-Curable Polymers Using Direct Ink Writing, Luis A. Velazquez

LSU Master's Theses

This thesis presents the design and implementation of a robotic additive manufacturing system that uses ultraviolet (UV)-curable thermoset polymers. Its design considers future applications involving free-standing 3D printing by means of partial UV curing and the fabrication of samples that are reinforced with fillers or fibers to manufacture complex-shape objects.

The proposed setup integrates a custom-built extruder with a UR5e collaborative manipulator. The capabilities of the system were demonstrated using Anycubic resin formulations containing fumed silica (FS) at varying weight fractions from 2.8 to 8 wt%. To fully cure the specimens after fabrication, a UV chamber was used. Then, measurements …

Grey-Taguchi Approach To Optimize Fused Deposition Modeling Process In Terms Of Mechanical Properties And Dimensional Accuracy, Md Asif Bin Syed, Qausar Rhaman, Hasan Md Shahriar, Mohammad Muhshin Aziz Khan

Graduate Student Scholarship

Fused Deposition Modeling (FDM) is a process that allows for the rapid production of functional parts through the deposition of fused material layers in a sequential manner. FDM has flexibility and the potential to create complicated parts. This study aims to optimize the FDM process parameters in terms of tensile strength, flexural strength, and longitudinal shrinkage using the Grey-Taguchi approach. The input parameters chosen to study the effects on dimension and mechanical properties are layer thickness, the raster angle, fill density, the number of contours, printing temperature, and printing speed. The Taguchi L27 orthogonal array is used as the statistical …

Utilization Of Resin-Based Additive Manufacturing For Investment Casting, Matthew Frost, Isaiah Hong

Mechanical Engineering

Dr. Xuan Wang, an Industrial & Manufacturing Engineering (IME) professor at California Polytechnic State University, San Luis Obispo, has sponsored the resin-based 3D printing investment cast senior project. The objective of the project was to thoroughly research the process and document the findings of using a resin-based 3D printed part as the pattern for investment casting. While this manufacturing process is not necessarily a new idea, the lack of technical research and documentation limits its ability to be reproducible. The research portion of the senior project included analyzing the limitations to the printing/casting manufacturing process. Measurements of part thicknesses, hole …

Multi-Objective Optimization On Dimensional Accuracy, Edge And Surface Quality Of 3d-Printed Parts By Fused Deposition Modelling, Islam Hamdy Salem

Theses and Dissertations

Fused Deposition Modelling (FDM) is one of most common additive manufacturing (AM) techniques used in manufacturing field. It has been increasingly used because of its low cost and simplicity. Although FDM can save time through eliminating pre-processing tooling-up to produce the end-user product, still a better final product quality, like mechanical properties, dimensional accuracy and surface finish, is needed. This thesis addresses the maximization of involved printing parameters in one reliable model. Hence, a wider investigation is conducted in this research via experimental work in order to obtain a comprehensive model that involves and relates more parameters in a single …

Workforce Development Strategies In Additive Manufacturing, Mel Cossette, Ismail Fidan, Gaffar Gailani, Angran Xiao

Publications and Research

Additive Manufacturing (AM), also known as 3D Printing (3DP), is one of the newest manufacturing technologies with growing utilization in our daily life. Parallel to this growth, new materials, machines, and specific processes are being developed to produce parts in better-finished quality, at lower cost, and with shorter production time. However, workforce education in this evolving field has not advanced at the same pace as the technology, lacking proven curriculums, high-quality/accredited degree programs, and specialized advanced degrees. In this paper, some best practices established by the authors are introduced. The list is far from exhaustive but is proven to be …

Design And Fabrication Of A Polymer Fdm Printer Capable Of Build Parameter Monitoring And In-Sit Geometric Monitoring Via Photogrammetry, Travis Roberts

All Theses

Additive manufacturing, or 3D printing, is a complex process that creates free-form geometric objects by sequentially placing material in a location to construct an object, usually as a layer-by-layer process. One of the most widespread methods is Fused Deposition Modeling (FDM). FDM is used in many of the consumer-grade polymer 3D printers available today. While consumer grade machines are cheap and plentiful, they lack many of the features desired in a machine used for research purposes and are often closed-source platforms. Commercial-grade models are more expensive and are also usually closed-source platforms that do not offer flexibility for modifications often …

Med-Drop Pill Dispenser, Cole Pike, Taylor Morris, Christopher Bruni, Jose Gomez

Mechanical Engineering

Veterans’ Affairs home care nurses currently spend anywhere from thirty minutes to two hours filling out monthly prescriptions one pill at a time to veterans who are unable to leave their homes. The goal of this project was to create an easy-to-use device that could be left at a patient’s home that nurses could use to quickly and accurately dispense medication into the patient’s monthly pill box.

Printing Parameter Determination And Characterization Of Additively Manufactured Kovar Steel, Will Macgreggor Davidson

Mechanical Engineering ETDs

Kovar (ASTM F15, UNS K94610) steel has many applications across Sandia National Laboratories but is best known within academia and industry for its glass-to-metal and glass-to-ceramic hermetic sealing capabilities. Successful printing parameters for a Renishaw AM400 to additively manufacture artifacts from Kovar steel powder have been determined. The printed test artifacts have been studied for ultimate tensile strength, density, surface roughness, hardness, bulk composition, and impact toughness. Longer throughput measurements such as porosity, coefficient of thermal expansion, and grain structure studies have been established for future delivery to the research team. Yet another delivery from this thesis research is a …

Design For Additive Manufacturing (3d Printing), Michael O'Donnell, Michael J. Levy

Williams Honors College, Honors Research Projects

The goal of this project is to study the performance of a 3D printed mechanical part subjected to topology optimization. A part that is somewhat complex in its load bearing and geometry will be selected. That part will then be designed, finite element analysis will be performed on it to optimize its topology, and then it will be 3D printed and tested. The goal of topology optimization is to either save material cost and/or part weight due to the ability of 3D printing to manufacture parts with complex and obscure geometry.

Utilization Of Recycled Filament For 3d Printing For Consumer Goods, Alexa Peterson

Apparel Merchandising and Product Development Undergraduate Honors Theses

The 3D printing market has been used in a wide variety of manufacturing industries including textile and apparel. Many consumers can now own a personal 3D printer at home for recreational printing. There are even websites dedicated to 3D printing patterns made by consumers. However, the materials used in the 3D printing process pose a problem for the environment due to their plastic-based nature. 3D printing is a layered process with each layer being printed depending on the layer below it for strength and stability. During the 3D printing process, great amounts of waste are produced as a result of …

3d Printing Of Iron Oxide Incorporated Polydimethylsiloxane Soft Magnetic Actuator, Rasoul Bayaniahangar

Dissertations, Master's Theses and Master's Reports

Soft actuators have grown to be a topic of great scientific interest recently. As the fabrication of soft actuators with conventional microfabrication methods are tedious, expensive, and time consuming, employment of 3-D printing fabrication methods appears promising as they can simplify fabrication and reduce the production cost. Complex structures can be fabricated with 3-D printing such as helical coils can achieve actuation performances that otherwise would not be possible with simpler geometries. In this thesis development of soft magnetic helical coil actuators of iron-oxide embedded polydimethylsiloxane (PDMS) was achieved with embedded 3-D printing techniques. Composites with three different weight ratios …

A Scalable, Chunk-Based Slicer For Cooperative 3d Printing, Jace J. Mcpherson

Computer Science and Computer Engineering Undergraduate Honors Theses

Cooperative 3D printing is an emerging technology that aims to increase the 3D printing speed and to overcome the size limit of the printable object by having multiple mobile 3D printers (printhead-carrying mobile robots) work together on a single print job on a factory floor. It differs from traditional layer-by-layer 3D printing due to requiring multiple mobile printers to work simultaneously without interfering with each other. Therefore, a new approach for slicing a digital model and generating commands for the mobile printers is needed, which has not been discussed in literature before. We propose a chunk-by-chunk based slicer that divides …

Guardian Condor, Kevin Bayonnet

Williams Honors College, Honors Research Projects

Our group has teamed up with Dr. Williams from Discovery Lab Global to research the capabilities of 3D printed Unmanned Aerial Vehicles (UAVs). The goal of our project is to deliver a 3D printed glider prototype which can later be fitted with electronics for controlled flight. The glider must also carry a payload of 2 to 3 pounds in addition to the electronics. These requirements must be met all while using a basic 3D printer with low cost plastic

Throughout the Fall 2017 semester, our group made a significant amount of progress by completing the conceptual design portion of the …

Thermal Analysis Of 3d Printed 420 Stainless Steel, Adithya Pothuri

All Graduate Theses, Dissertations, and Other Capstone Projects

Additive manufacturing opens new possibilities in the manufacturing industry. 3D printing is a form of additive manufacturing. 3D printers will have a significant influence over the industrial market, with extremely positive effects in no time. The main aim of this research is to determine the effect of process parameters of Binder Jet manufactured 420 Stainless Steel (420SS) parts on thermal properties such as thermal conductivity. Different parameters, such as layer thickness, sintering time and sintering temperature were varied. A full factorial design of experiment matrix was made by varying these parameters using two levels. Testing showed that different parameters affected …

Selective Resistive Sintering: A Novel Additive Manufacturing Process, Austin Bryan Van Horn

Graduate Theses and Dissertations

Selective laser sintering (SLS) is one of the most popular 3D printing methods that uses a laser to pattern energy and selectively sinter powder particles to build 3D geometries. However, this printing method is plagued by slow printing speeds, high power consumption, difficulty to scale, and high overhead expense. In this research, a new 3D printing method is proposed to overcome these limitations of SLS. Instead of using a laser to pattern energy, this new method, termed selective resistive sintering (SRS), uses an array of microheaters to pattern heat for selectively sintering materials. Using microheaters offers significant power savings, significantly …

A Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content (< 1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Fiber Length Attrition In Additive Manufacturing, Michael Chapiro

Materials Engineering

Chopped carbon fibers are used as reinforcements in thermoplastics, but the viscous shear forces that arise in melt-processing reduces the fiber length well below its critical length resulting in only moderate strength and stiffness gains compared to the neat resin. This research project aimed to experimentally determine the effect of the melt–flow portion of a single-screw- extrusion process on carbon fiber length attrition in isolation from the immediately preceding screw–plastication step that is responsible for most of the heat needed for melting. Carbon fibers with an initial length of 2 mm were stirred into 5,000 centipoise and 10,000 centipoise silicone …

Multiple Apple Box Lift 1/10th Scale Model, Kyle J. Burlingame

All Undergraduate Projects

Title and Author: 1/10th Scale Multiple Apple Box Lift by Kyle Burlingame (Engineering Technologies, Safety, and Construction) Abstract/Artist statement: A 1/10th scale Multiple Apple Box Lift was designed and built as a proof of concept for a full scale device. The Multiple Apple Box Lift was designed to meet a customer’s requirements and to be presented at SOURCE. This device lifts the top half of the stacked apple boxes on a pallet in order to allow access to the boxes in the middle of the stack. The device can be manually operated by two people while in-between narrow rows of …