Manufacturing Commons^™

Generator Design: A Study Of Optimized Airflow, Rachel Wattleworth

Williams Honors College, Honors Research Projects

The core goal of this project was to prototype, test, and evaluate a new type of fan for the Safran Electrical & Power air-cooled generators. The idea of a new fan being made for these two generators arose when they were not adhering to design requirements. A base mixed-flow fan was created to test on multiple generators. Upon creating a prototype, it will be tested to prove if it can increase the air flow, decrease temperatures, and increase power and life of the machines. They all proved to be successful and achieve the main objectives for this project. Data such …

Power Wheelchair Canopy, Mohamed F. Battah, Joshua D. Brown, Dujuan J. Mcclendon, Gavin M. Francisco

Williams Honors College, Honors Research Projects

Some power wheelchair users can not drive and independently hold an umbrella at the time because they do not have much upper body strength. Therefore, users are unprotected from the rain and are getting soaking wet. One of the members of this group is in a wheelchair and faces this problem. He has previously searched for something to protect him from rain, but could not found something he could independently use. What users need is a powered umbrella that attaches to their power wheelchair. There is no such umbrella available in the market. In this project, the solution to this …

Recumbent Bicycle Balancing Aid, James Hager

Williams Honors College, Honors Research Projects

For our senior design project, our team will be consulting to create a balancing aid system intended for the recumbent bicycle shown below in Figure 1. The owner of the bicycle is Robert Henderson, a former United States Navy sailor from Northeast Ohio who picked up biking and skiing while he was stationed in Maine in the late 80’s. While there, he took to the mountains on the rugged terrain and brought this passion of biking back home to share with his wife, Johanna once he completed his service to his country. Biking became an integral part of the …

Testing Of A Human Powered Vehicle, Bailey Conard, Marlee Reynolds

Williams Honors College, Honors Research Projects

The University of Akron’s Human Powered Vehicle Team designed a high performing, fully functioning vehicle that is safe, efficient, and practical for the 2018-2019 season. These objectives were the main priorities when it came to the initial stages of designing the vehicle. In addition, the vehicle was designed in accordance with the ASME 2019 Human Powered Vehicle Challenge guidelines to satisfy all the rules and requirements. Additional priorities have been created to teach practical engineering skills and techniques to the students participating in the project through different points in the production process including research, vehicle design, manufacturing, and testing.

The …

Energy Efficiency Evaluation Of Blower Heater Non-Purge Compressed Air Dryers, Alexandra M. Botts

Graduate Theses, Dissertations, and Problem Reports (ETD)

There are several compressed air dryers available for industrial use including, refrigerant, desiccant, and membrane. This research focuses on twin tower regenerative closed loop desiccant dryers, specifically: blower heater non-purge (BHNP) with and without cooling water pumps, Compressed-air Heater Purge (CHP), Blower Heater Purge (BHP), and Pressure Swing Heaterless (PSH). These styles of dryers are used mainly in industries that require extremely dry air such as, food manufacturing, medical air, or sensitive technology manufacturers. The research was conducted by collecting and analyzing real time current draw data on air compressors and associated dryers at eight different facilities (13 compressor systems) …

Hydrogen Fuel Cell Gasket Handling And Sorting With Machine Vision Integrated Dual Arm Robot, Devin C. Fowler

College of Graduate Studies: Theses & Dissertations

Recently demonstrated robotic assembling technologies for fuel cell stacks used fuel cell components manually pre-arranged in stacks (presenters), all oriented in the same position. Identifying the original orientation of fuel cell components and loading them in stacks for a subsequent automated assembly process is a difficult, repetitive work cycle which if done manually, deceives the advantages offered by automated fabrication technologies of fuel cell components and by robotic assembly processes. We present an innovative robotic technology which enables the integration of automated fabrication processes of fuel cell components with robotic assembly of fuel cell stacks into a fully automated fuel …

Differential Mobility Classifiers In The Non-Ideal Assembly, Thamir Alsharifi

Theses and Dissertations

The differential mobility classifier (DMC) is one of the core components in electrical mobility particle sizers for sizing sub-micrometer particles. Designing the DMC requires knowledge of the geometrical and constructional imperfection (or tolerance). Studying the effects of geometrical imperfection on the performance of the DMC is necessary to provide manufacturing tolerance and it helps to predict the performance of geometrically imperfect classifiers, as well as providing a calibration curve for the DMC. This thesis was accomplished via studying the cylindrical classifier and the parallel plate classifier. The numerical model was built using the most recent versions of COMSOL Multiphysics^{® …}

Material Interactions And Self-Assembly In Inkjet Printing, Karam Nashwan Al-Milaji

Theses and Dissertations

Inkjet printing has attracted much attention in recent years as a versatile manufacturing tool, suitable for printing functional materials. This facile, low-cost printing technique with high throughput and accuracy is considered promising for a wide range of applications including but not limited to optical and electronic devices, sensors, solar cells, biochips, and displays. The performance of such functional devices is significantly influenced by the deposit morphology and printing resolution. Therefore, fabrication functional devices with precise footprints by inkjet printing requires deep understanding of ink properties, material interactions, and material self-assembly.

In conventional inkjet printing process, where sessile droplets are directly …

Laser Machining Countersinks In Carbon Fiber Reinforced Polymer, Leon James Neely Hill

Masters Theses

“Laser machining countersinks with a frequency doubled Q-switched diode pumped Nd:YAG laser is demonstrated. Tests were conducted in 0.100" thick IM7 prepreg CFRP with [0,90]3S orientation. The HAZ is minimized to avoid stress concentrations in the epoxy matrix. A chamber and filtration system was designed and built to contain the byproducts produced in the machining process. The variables investigated are the number of repetitions in the offset path, the plunge rate, and the line energy. The research was performed over one baseline study, one parameter space exercise, two full factorial experiments, and one repeatability study. Assessment was done under an …

Developing A Commercial Product Using A Consumer Grade 3d Printer, Calvin Smith

All Graduate Theses, Dissertations, and Other Capstone Projects

The development of affordable, quality, consumer grade 3D printers has allowed entrepreneurs to develop new products and start small businesses. As the print quality of consumer grade printers has improved entrepreneurs have been able to develop consumer quality products without the traditional expense of mass manufacturing. This change from mass manufacturing to small scale and custom production has allowed for the growth of small businesses. Websites such as www.etsy.com show hundreds of small businesses based on 3D printing, these businesses showcase thousands of products ranging from useful household items to cosplay. This thesis covers the process of a small business …

Developing A Testing Instrument To Evaluate The Performance Of 3d-Printed Body-Powered Prosthetic Hands, Araz Al-Dawoodi

All Graduate Theses, Dissertations, and Other Capstone Projects

A 3D printed prosthetic hand is an open source technology that became a good substitution for many products in the market. For many reasons, Low-cost, easy made / easy build. As an open source product, 3D printed prosthetic designs are available to anyone around the world, a good option for young children because they need to have a new prosthetic more frequent until they reach the adulthood age. Most families cannot pay a thousand dollars technology. From the research, it found that that there are not enough studies cover the open source wrist body-powered prosthetic. Other studies covered products used …

Managing Variability In Assembly Lines, Sumanth Gokapai

All Graduate Theses, Dissertations, and Other Capstone Projects

Every successful company have a diversified product portfolio based on their customer demand. Though products are branded as different variants, versions etc. most of them are similar products with little variations in their features or functions they perform. With the traditional, product centric approach to handle variation, new techniques like Clone and own were implemented in which engineers pick the most similar one available, copy it, make changes to it and present it as a new variant. Even though this approach employs reuse, but the savings occur once and only once. This project discussed how companies can exploit the commonality …

Reactive Archey Target Design Team "Mimic", Brandon Croyle, Jacob Boss, David Rodgers, Austin Wivell

Williams Honors College, Honors Research Projects

This design project will aim to provide archery hunters with a platform to simulate shooting at string jumping deer. String jumping refers to a spooked deer hearing the snap of a bow string and instintivly ducking up to ten inches. This often results in wounded or missed deer. We will design and build a control system that uses the sound of a bow string as a trigger to operate a mechanical target system. A sound sensor will mimic a deer’s hearing in close range hunting and then send a signal to the mechanical system to replicate the dropping motion of …

Center Lift Trailer Support Structure, Carson Corle, Anthony M. Hayes, Bryan A. Truax

Williams Honors College, Honors Research Projects

Center lift pontoon trailers have a high center of gravity, therefore have the potential for the pontoon and trailer to tip while cornering. There is need for a component to stabilize the pontoon on the trailer while towing. Different concepts of a support system were sketched to determine the best option. The characteristics that were deemed important for the support system were narrowed down to determine the best concept and the connections of the best design were sketched in greater detail. The forces that the support system would have to withstand to stabilize the pontoon on the trailer were calculated. …

Metric Coil Car, Abigail Eberly

Williams Honors College, Honors Research Projects

Coil cars are a vital part of many steel mills. They allow mills to easily transfer a coil from one location to another without the use of a crane, manual labor, or other extraneous forces. Steel Equipment Specialists, or SES, gets multiple orders every year for coil cars. While the general functions and goals of the cars remains consistent, the details, such as the size of the car, the distance between rails, and the weight/ size of the coils differs between each place. Due to this variety, SES has requested a coil car that can easily be manipulated and produced …

Carbon Fiber Monocoque, Dan Brown, Leland Hoffman

Williams Honors College, Honors Research Projects

The University of Akron’s Human Powered Vehicle Team designed a high performing, fully functioning vehicle that is safe, efficient, and practical for the 2018-2019 season. These objectives were the main priorities when it came to the initial stages of designing the vehicle. In addition, the vehicle was designed in accordance with the ASME 2019 Human Powered Vehicle Challenge guidelines to satisfy all the rules and requirements. Additional priorities have been created to teach practical engineering skills and techniques to the students participating in the project through different points in the production process including research, vehicle design, construction, and testing.

The …

Rheological Properties Of Two Stainless Steel 316l Powders For Additive Manufacturing, Haijun Gong, Xiaodong Xing, Hengfeng Gu

Manufacturing Engineering: Faculty Publications (2015-2023)

This study measures the rheological properties of two stainless steel 316L powders which are used for the powder-bed-fusion based additive manufacturing process. The purpose is to evaluate the newly acquired powder in comparison with the used and recycled powder, so that both powders can be mixed with each other to supplement the powder usage. The powder rheology properties, such as dynamic property, bulk property, and shear property, are tested and compared. The results and analysis confirm the compatibility of powder mixing.

Remotely Controlled Industrial Robotic Arm And Simulation Of Automated Thermal Furnace, Prince Mehandi Ratta

Dissertations, Master's Theses and Master's Reports

The right execution of controllers ensures the correct analysis of information, generating efficient results and better optimizing the system. In this report, two controllers were designed. Firstly, a remotely controlled robotic arm, since there are no such type commercially available controllers. Moreover, robotic platforms are costly, so students and researchers are often unable to learn the concepts of programming industrial robots. This project makes a non-destructive, remotely-controlled robotic arm to better teach students and researchers about programming and control of robotic arms. Secondly, simulation of an automated thermal furnace for ArcelorMittal on SIMULINK, which is used for the annealing process …

3d Printing In Low Resource Healthcare Settings: Analysis Of Potential Implementations, Alenna Beroza

Dissertations, Master's Theses and Master's Reports

3D printing has gained significant momentum in the past ten years, and its unique advantages make it especially ideal for use in low resource healthcare settings, where many designs have already been successfully implemented. Yet, little has been studied on how 3D printing can be sustainably and functionally implemented in low resource healthcare systems as a manufacturing practice. In this report, three business models are proposed for this implementation: In-House Operator, Independent Operator, and Print Farm. These models were then tested over four months in Kisumu county, Kenya, at two workshops and seven public hospitals. I worked with local medical …

Light Touch Based Virtual Cane For Balance Assistance During Standing, Sindhu Reddy Alluri

Masters Theses

"Can additional information about one's body kinematics provided through hands improve human balance? Light-Touch (LT) through hands helps improve balance in a wide range of populations, both healthy and impaired. The force is too small to provide any meaningful mechanical assistance -- rather, it is suggested that the additional sensory information through hands helps the body improve balance.

To investigate the potential for improving human balance through biofeedback through hands, we developed a Virtual Cane (VC) for balance assistance during standing. The VC mimics the physical cane's function of providing information about one's body in space. Balance experiments on 10 …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston

Mechanical Engineering Undergraduate Honors Theses

Throughout the process of steel making, certain grades of steel are a higher risk for defects caused by the inability to quickly diffuse hydrogen through the steel when cooled to room temperature at a normal rate based on the ambient air temperature. To reduce the hydrogen flaking defects that are caused due to hydrogen entrapment in the steel, the process of slow cooling is utilized. This process reduces the cooling rate of steel bars by keeping them at a higher temperature for extended periods and in turn gives the hydrogen a chance to fully dissipate from the steel. In many …

A Scalable, Chunk-Based Slicer For Cooperative 3d Printing, Jace J. Mcpherson

Computer Science and Computer Engineering Undergraduate Honors Theses

Cooperative 3D printing is an emerging technology that aims to increase the 3D printing speed and to overcome the size limit of the printable object by having multiple mobile 3D printers (printhead-carrying mobile robots) work together on a single print job on a factory floor. It differs from traditional layer-by-layer 3D printing due to requiring multiple mobile printers to work simultaneously without interfering with each other. Therefore, a new approach for slicing a digital model and generating commands for the mobile printers is needed, which has not been discussed in literature before. We propose a chunk-by-chunk based slicer that divides …

Photochemical Etching Of Nitrided Stainless Steel Piston Rings, Steven Sonntag

Mechanical Engineering Undergraduate Honors Theses

Piston rings are designed to provide a seal between the piston and the cylinder wall of internal combustion engines, keeping oil from the crankcase from getting into the combustion chamber. This means piston rings are the main point of contact between the piston and the cylinder wall, which causes the piston to experience high amounts of friction and wear. By texturing the surfaces of the cylinder wall and/or the piston ring, the amount of contact area can be reduced, allowing for less friction, slower wear, and better gas mileage. In this thesis experiments, photochemical etching processes were developed to etch …

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

All-Terrain Storage Surfboard Carts, Ben M. Kennedy, Danny Riedeman, Roberto Gonzalez

Mechanical Engineering

All Terrain Storage consists of three mechanical engineering students: Roberto Gonzalez, Ben Kennedy, and Danny Riedeman. The goal of All Terrain Storage is to design and create two portable storage devices for the non-profit organization AmpSurf. AmpSurf helps veterans, people with disabilities, and anyone else who could be helped through adaptive surfing and other outdoor activities. Their current method of storing and transporting equipment for events is carrying it from the trailer in the parking lot through the sand onto the beach. This document will provide: a more thorough introduction to AmpSurf and the project, the objectives, background information, the …

Daimscale — 1:14th Tractor-Trailer For Testing Driver Assistance Technology, Christopher Marrale, Jase Sasaki, Devin Bodmer

Mechanical Engineering

Active driver assistance systems are becoming increasingly wide-spread throughout the automotive industry due to their potential for safer roads and decreased costs of transportation, but testing these systems on real trucks can be time consuming, dangerous, and costly. Testing these systems on a small-scale tractor-trailer combination will lead to faster and more efficient development of driver assistance systems and can be used by both engineers and students, leading to a larger field of experienced developers to improve these systems.

Our goal will be to design, manufacture, and build a scale 6x2 model of the tractor portion of a Daimler semi-truck …

A Systematic Approach To High Blood Pressure Risk Analysis And Healthcare Cost Reduction In Young Adults [Metodología Sistemática Para El Análisis De Riesgo Y Reducción De Costos De Servicios Médicos De Hipertensión En Adultos Jóvenes], Francisco Rafael Torres Diaz

Theses and Dissertations

The purpose of this research is to utilize publicly available data to estimate the current rate of occurrence of undiagnosed High Blood Pressure (HBP) in young adults (18 to 24 years old) and the out-of-pocket healthcare expenses associated with complications of HBP, to provide feasible alternatives to mitigate the effects on a region's economy. This has been done by building a Risk Factor Simulation Model that utilizes known HBP risk factors’ correlation to HBP, insurance coverage data, and rate of diagnosis to formulate the average Risk Factor Value for a region, which through an Annual Expected Cost Function estimates the …

Single Arm Recumbent Bicycle, Alexander Borsotti, Ryan Westermann, Sean Liston

Mechanical Engineering

The goal of this report is to outline and cover the scope of work for the Single Arm Recumbent Bicycle Senior Project. The report will give an introduction of the problem, a background of the existing research or products relating to our project, the objectives of our project, our project management plan, our final design, manufacturing, testing, our project management, and final recommendations for improving the final design. The team is being supported by the Quality of Life Program, a non-profit organization that works to improve the lives of those injured in duty while serving our nation.

Up until now, …

Process-Property-Microstructure Relationships In Laser-Powder Bed Fusion Of 420 Stainless Steel., Subrata Deb Nath

Electronic Theses and Dissertations

Laser-powder bed fusion (L-PBF) is an additive manufacturing technique for fabricating metal components with complex design and customized features. However, only a limited number of materials have been widely studied using L-PBF. AISI 420 stainless steel, an alloy with a useful combination of high strength, hardness, and corrosion resistance, is an example of one such material where few L-PBF investigations have emerged to date. In this dissertation, L-PBF experiments were conducted using 420 stainless steel powders to understand the effects of chemical composition, particle size distribution and processing parameters on ensuing physical, mechanical and corrosion properties and microstructure in comparison …