Mechanics of Materials Commons^™

Hybrid Manufacturing: Integrating Stereolithography And Direct Print Technologies, Amit Lopes

Open Access Theses & Dissertations

The focus of this research was the development of a hybrid manufacturing system that integrates stereolithography (SL) and direct print (DP) technologies to fabricate three dimensional (3D) structural electronic devices within a single set-up. The capabilities of this new additive manufacturing (AM) technology was explored in the context of fabricating and prototyping complex electronic devices in which conformal shape, rugged and light-weight integration, and a natural resistance to reverse engineering are all of paramount importance. Consequently, electronic components can be tightly integrated together in a rugged, light-weight 3D structure of arbitrary form. This research is a continuing advancement of the …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Temporal Scales For Transport Patterns In The Gulf Of Finland, Bert Viikmae, Tarmo Soomere, Mikk Viidebaum, Mihhail Berezovski

Publications

The basic time scales for current-induced net transport of surface water and associated time scales of reaching the nearshore in the Gulf of Finland, the Baltic Sea, are analysed based on Lagrangian trajectories of water particles reconstructed from three-dimensional velocity fields by the Rossby Centre circulation model for 1987–1991. The number of particles reaching the nearshore exhibits substantial temporal variability whereas the rate of leaving the gulf is almost steady. It is recommended to use an about 3 grid cells wide nearshore area as a substitute to the coastal zone and about 10–15 day long trajectories for calculations of the …

Waves In Materials With Microstructure: Numerical Simulation, Mihhail Berezovski, Arkadi Berezovski, Juri Engelbrecht

Publications

Results of numerical experiments are presented in order to compare direct numerical calculations of wave propagation in a laminate with prescribed properties and corresponding results obtained for an effective medium with the microstructure modelling. These numerical experiments allowed us to analyse the advantages and weaknesses of the microstructure model.

Method Of Transferring Strained Semiconductor Structure, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

The transfer of strained semiconductor layers from one substrate to another substrate involves depositing a multilayer structure on a substrate having surface contaminants. An interface that includes the contaminants if formed in between the deposited layer and the substrate. Hydrogen atoms are introduced into the structure and allowed to diffuse to the interface. Afterward, the deposited multilayer structure is bonded to a second substrate and is separated away at the interface, which results in transferring a multilayer structure from one substrate at least one strained semiconductor layer and at least one strain-induced seed layer. The strain-induced seed layer can be …

Imprinting Polymerfilm On Patterned Substrate, Li Tan, Yen-Peng Kong, Stella W. Pang, Albert F. Yee

Department of Mechanical and Materials Engineering: Faculty Publications

A method of applying a pattern on a topography includes first applying a polymer film to an elastormer member, such as PDMS, to form a pad. The pad is then applied to a substrate having a varying topography under pressure. The polymer film is transferred to the substrate due to the plastic deformation of the polymer film under pressure compared to the elastic deformation of the PDMS member pulls away from the polymer layer, thereby depositing the polymer layer, thereby depositing the polymer layer upon the substrate.

Indentation Creep Analysis For Self Similar Indenters, Sandeep V. Thube

Mechanical & Aerospace Engineering Theses & Dissertations

In indentation creep experiments, it is difficult to characterize the mechanical properties of small size specimens using conventional methods. This study uses finite element modeling to investigate rate-sensitive deformation of materials with different hardness and strain rate sensitivities for self similar indenter tip geometries. The simulation model is developed using commercially available finite element software Abaqus/Standard. Our study investigates the difference between strain rate sensitivity of hardness (vH) and of flow stress (vu) and their relation to the hardness/modulus ratio. It reveals that the commonly held assumption that vH = vu is violated except for materials with low hardness/modulus …

Waves In Inhomogeneous Solids, Arkadi Berezovski, Mihhail Berezovski, Juri Engelbrecht

Publications

The paper aims at presenting a numerical technique used in simulating the propagation of waves in inhomogeneous elastic solids. The basic governing equations are solved by means of a finite-volume scheme that is faithful, accurate, and conservative. Furthermore, this scheme is compatible with thermodynamics through the identification of the notions of numerical fluxes (a notion from numerics) and of excess quantities (a notion from irreversible thermodynamics). A selection of one-dimensional wave propagation problems is presented, the simulation of which exploits the designed numerical scheme. This selection of exemplary problems includes (i) waves in periodic media for weakly nonlinear waves with …

Flexible Electronics Using Ion Implantation To Adhere Polymer Substrate To Single Crystal Silicon Substrate, Terry L. Alford, Douglas C. Thompson Jr., Hyunchul Kim, Michael A. Nastasi, James W. Mayer, Daniel Adams

Department of Mechanical and Materials Engineering: Faculty Publications

An electronic apparatus uses a single crystalline silicon Substrate disposed adjacent to a flexible substrate. The electronic apparatus may be a flexible flat panel display, or a flexible printed circuit board. The flexible substrate can be made from polymer, plastic, paper, flexible glass, and stainless steel. The flexible substrate is bonded to the single crystalline substrate using an ion implantation process. The ion implantation process involves the use of a noble gas Such as hydrogen, helium, Xenon, and krypton. A plurality of semiconductor devices are formed on the single crystalline silicon Substrate. The semi conductor devices may be thin film …

Performance Analysis Of Coal-Fired Boiler And Natural Gas Fired Boiler At Morehead State University, Devender Banne

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science & Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Devender Banne on May 4, 2009.

Droplet Assisted Self-Assembly Of Semiconductor Nanostructures, Kimberly Annosha Sablon

Graduate Theses and Dissertations

There is increasing interest in quantum dot (QD) structures for a plethora of applications, including optoelectronic devices, quantum computing and energy harvesting. While strain driven surface diffusion via stranski-krastanow (SK) method has been commonly used to fabricate these structures, a more recent technique, droplet epitaxy (DE) does not require mismatch strain and is therefore much more flexible in the combination of materials utilized for the formation of QDs.

As reported in this work, a hybrid approach that combines DE and SK techniques for realizing lateral ordering of QDs was explored. First, the droplet formation of various materials was discussed and …

Multiscale Modeling Of Impact On Heterogeneous Viscoelastic Solids With Evolving Microcracks, Flavio V. Souza

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Multiscale computational techniques play a major role in solving problems related to viscoelastic composite materials due to the complexities inherent to these materials. In the present work, a numerical procedure for multiscale modeling of impact on heterogeneous viscoelastic solids containing evolving microcracks is proposed in which the (global scale) homogenized viscoelastic incremental constitutive equations have the same form as the local scale viscoelastic incremental constitutive equations, but the homogenized tangent constitutive tensor and the homogenized incremental history dependent stress tensor depend on the amount of damage accumulated at the local scale. Furthermore, the developed technique allows the computation of the …

Effect Of Steam Environment On Creep Behavior Of Nextel720/Alumina-Mullite Ceramic Matrix Composite At Elevated Temperature, Tolga Kutsal

Theses and Dissertations

The tensile creep behavior of an oxide-oxide ceramic matrix composite (CMC) was investigated at 1000 and 1100° C in laboratory air and steam. The oxide-oxide CMC studied in this research was Nextel™ 720/alumina-mullite (N720/AM). The composite consists of N720/fibers with 0°/90° fiber orientation and a porous alumina-mullite matrix. Tensile-strain behavior was investigated and tensile properties measured at 900, 1000 and 1100° C. The effect of loading rate on tensile properties of N720/AM ceramic matrix composite at 1100° C in steam was also examined. Creep-rupture tests were performed at 1100° C in laboratory air and steam, and at 1000° C only …

A Finite Element Evaluation Of An Experiment Related To Coating Damping Properties, Armando Deleon

Theses and Dissertations

Typically turbine engine blades gain protection from thermal damage by the use of hard coatings, such as magnesium aluminate spinel. Known as Thermal Barrier Coatings (TBC's), they have material properties that include several nonlinearities. These TBC's create damping primarily due to their nonlinear dissipation of energy. In order to effectively represent their damping properties, it is necessary to create a method which combines experimentation and analysis. Previous work has shown the need for a beam bounded and loaded in such a fashion that external support energy dissipation functions i.e. boundary conditions and aerodynamics are eliminated. Thus, a new experimental apparatus …

Effects Of Prior Aging At 316°C In Argon On Inelastic Deformation Behavior Of Pmr-15 Polymer At 316°C: Experiment And Modeling, Ozgur Ozmen

Theses and Dissertations

The inelastic deformation behavior of PMR-15 neat resin, a high-temperature polymer, was investigated at 316 deg C. The experimental program was designed to explore the influence of strain rate on tensile loading, unloading, and strain recovery behaviors. In addition, the effect of the prior strain rate on the relaxation response of the material, as well as on the creep behavior following strain controlled loading were examined. The material exhibits positive, nonlinear strain rate sensitivity in monotonic loading and unloading. Early failures occur in the inelastic regime. The recovery of strain at zero stress and creep response are strongly affected by …

Thermomechanical Properties Of Center-Reinforced Aluminum, Geofrey S. Cox

Theses and Dissertations

The rule of mixture approach was shown to produce an accurate theoretical prediction of the room temperature elastic modulus values when compared to the experimental results. The laminate's modulus value remained relatively constant over the -55C to 80C temperature range, indicating stable behavior despite temperature changes. Blunt notch tests also revealed that the laminate's strength was not significantly reduced due to the presence of small holes. Finally, fatigue testing demonstrated that the laminate retains its stiffness properties throughout its fatigue life, until failure.

The Effect Of Silicon Content On Impact Toughness Of T91 Grade Steels, Ajit K. Roy, Pankaj Kumar, Debajyoti Maitra

Mechanical Engineering Faculty Research

The impact resistance of silicon (Si)-containing modified 9Cr-1Mo steels has been investigated within a temperature regime of -40 to 440°C using the Charpy method. The results indicate that the energies absorbed in fracturing the tested specimens were substantially lower at temperatures of -40, 25, and 75°C compared to those at elevated temperatures. Lower impact energies and higher ductile-to-brittle-transition-temperatures (DBTTs) were observed with the steels containing 1.5 and 1.9 wt.% Si. The steels containing higher Si levels exhibited both ductile and brittle failures at elevated temperatures. However, at lower temperatures, brittle failures characterized by cleavage and intergranular cracking were observed for …

Characterization Of A Viscoelastic Response From Thin Metal Films Deposited On Silicon For Microsystem Applications, Steven L. Meredith

Master's Theses

Understanding the mechanisms that control the mechanical behavior of microscale actuators is necessary to design an actuator that responds to an applied actuation force with the desired behavior. Micro actuators which employ a diaphragm supported by torsional hinges which deform during actuation are used in many applications where device stability and reliability are critical. The material response to the stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. A fully recoverable non-linear viscoelastic response has been observed in electrostatically driven micro actuators employing torsional hinges of silicon covered with thin metal films. …

The Investigation Of Nano Silica In The Cement Hydration Pro, Jonathan Samuel Belkowitz

Electronic Theses and Dissertations

With the advent of nano technology, materials have been developed that can be applied to high performance concrete mix designs. Nano silica reacts with calcium hydroxide (CH) to develop more of the strength carrying structure of cement: calcium silica hydrate (CSH). In this paper, relationships have been developed to distinguish the benefits when using different sizes of nano silica in cement paste. An extensive regime of experimental analysis was carried out to determine the effect of nano silica. Through these experiments the heat of hydration of multiple cement mix designs was measured. After that, the concentration of CH was recorded …

Identification Of Multiple Oscillation States Of Carbon Nanotube Tipped Cantilevers Interacting With Surfaces In Dynamic Atomic Force Microscopy, Mark Strus, Arvind Raman

Birck and NCN Publications

Carbon nanotubes (CNTs) have gained increased interest in dynamic atomic force microscopy (dAFM) as sharp, flexible, conducting, nonreactive tips for high-resolution imaging, oxidation lithography, and electrostatic force microscopy. By means of theory and experiments we lay out a map of several distinct tapping mode AFM oscillation states for CNT tipped AFM cantilevers: namely, noncontact attractive regime oscillation, intermittent contact with CNT slipping or pinning, or permanent contact with the CNT in point or line contact with the surface while the cantilever oscillates with large amplitude. Each state represents fundamentally different origins of CNT-surface interactions, CNT tip-substrate dissipation, and phase contrast …

Computational Model For Predicting Nonlinear Viscoelastic Damage Evolution In Materials Subjected To Dynamic Loading, Flavio V. Souza, Yong-Rak Kim, George A. Gazonas, David H. Allen

Department of Mechanical and Materials Engineering: Faculty Publications

Many inelastic solids accumulate numerous cracks before failure due to impact loading, thus rendering any exact solution of the IBVP untenable. It is therefore useful to construct computational models that can accurately predict the evolution of damage during actual impact/dynamic events in order to develop design tools for assessing performance characteristics. This paper presents a computational model for predicting the evolution of cracking in structures subjected to dynamic loading. Fracture is modeled via a nonlinear viscoelastic cohesive zone model. Two example problems are shown: one for model validation through comparison with a one-dimensional analytical solution for dynamic viscoelastic debonding, and …

Experimental Study Of The Response Of Semiconductor Detectors For Edxrf Analysis., Sunil Kumar Valaparla

Open Access Theses & Dissertations

This present work relates to the study and characterization of the response function of an energy-dispersive x-ray spectrometer. The problems of energy, efficiency and resolution calibration of the system operating in the energy (5-60 keV) range are discussed. We present the operation characteristics of the portable pyro-electric x-ray generator (COOL-X) and the application of the calibrated response spectrum in the elemental analysis using X-ray Fluorescence (XRF).

We study the response of the Si(Li)-Pin XR-100CR semiconductor detector to low energy photons. The photopeak efficiency was determined experimentally by using radioisotopes and compared against a theoretical efficiency curve. The efficiency for gamma …

Effects Of Aggregate Structure On Hot-Mix Asphalt Rutting Performance In Low Traffic Volume Local Pavements, Yong-Rak Kim, Hee Mun Park, Francisco Thiago Sacramento Aragão, Jamilla Emi Sudo Lutif

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this study is to evaluate the effect of mix gradations associated with the Superpave restricted zone on rutting potential specifically for low traffic volume roadways. Although the elim-ination of the restricted zone requirement in Superpave mix design is highly recommended, some questions still remain unanswered as the research conclusions supporting the elimination of the re-stricted zone were largely made for medium to high traffic volume roadways, where aggregates are highly crushed and of good quality. The applicability of such research conclusions based on high traffic volume mixes needs to be verified for low volume mixes because many …

Characterization And Cytotoxic Assessment Of Ballistic Aerosolized Particulates For Tungsten Alloy Penetrators Interacting With Steel Targets, Brenda Ivette Machado

Open Access Theses & Dissertations

The aerosolized particulates produced during an impact of depleted uranium munitions can potentially contaminate extensive areas around the impact sites and cause a wide spectrum of civilian and military damage. Thus materials such as WHA have been prompted for consideration. The present research is concerned with the regular collection of aerosol particulates associated with ballistic WHA rod penetration into rolled homogeneous steel (RHA) or other related steel armor as armor plate sequences. Particulate size characterization via scanning electron microscopy (SEM) and transmission electron microscopy (TEM) along with chemical compositions via energy dispersive spectroscopy (EDS) were the focus of this research. …

Fabrication And Characterization Of Zirconium Oxide Thin Films, Vemnkata Rama Sesha Ravi Kumar Vemuri

Open Access Theses & Dissertations

Zirconium oxide (ZrO2) is an important material with a potential for a wide range of technological applications. The outstanding chemical stability, electrical and mechanical properties, high dielectric constant, and wide band gap of ZrO2 make it suitable for several industrial applications in the field of optics, electronics, magneto-electronics, and optoelectronics. ZrO2 is frequently used as a high refractive index material in multilayer optical coatings in high power laser systems. ZrO2 is employed in super plastic structural ceramics that demonstrate excellent strength and fracture toughness. ZrO2 has been considered as a promising dielectric to replace SiO2 in advanced metal oxide semiconductor …

Art In A New Light: Design And Assessment Of Illuminants To Reduce Photochemical Degradation Of Works Of Art, Monica Fabiola Delgado

Open Access Theses & Dissertations

The purpose of this research is to design the best lighting that will minimize long term photochemical degradation of Old Master Drawings and/or other works of art, while maintaining the patron's appreciation of the object's color and detail. The present approach is a technological refinement to the basic underlying earlier work on fluorescent lighting by W. A. Thornton, W.A. at General Electric1. Thin-film dielectric, multi-coating technology is used to create filters that eliminate ultraviolet light, near infrared light and significant unnecessary parts from the visible spectrum, thus maximizing the reduction in photochemical degradation, while maintaining optimal color rendering. Three interference …

Additive Layer Manufacturing Of Ti-6al-4v By Electron Beam Melting From Powder Particles: Solid, Mesh And Foam Components Study, Sara M. Gaytan

Open Access Theses & Dissertations

Additive Manufacturing by Electron Beam Melting Rapid Manufacturing is a technology that consists of the fabrication of a CAD design by melting powder particles in a layer by layer fashion. In this study, Ti-6Al-4V has been utilized to fabricate solid, mesh and foam components by EBM technologies. Powder analysis of Ti-6Al-4V was performed to obtain a better understanding of the porosity obtained by the system. After proper optimization of the machine, and porosity control, microstructural analysis was performed to the components already mentioned and correlated by transmission electron microscopy. Besides the microstructural analysis, tensile and hardness testing was performed to …

Assessing Repeatability Of Four-Point Bending Method For Estimating Fatigue Cracking Of Hot Mix Asphalt, Sara -. Montazeri

Open Access Theses & Dissertations

The objective of this thesis was to assess the repeatability of four-point bending method for estimating fatigue cracking of hot mix asphalt. This experimental research examined the influence of mix proportions, specifically asphalt and air void contents, on fatigue behavior of asphalt beam specimens in the laboratory tested with four-point bending method of loading. Following the relevant specifications, the strain-controlled mode of loading was selected. Fatigue failure is expected to occur at the cycle which the flexural stiffness of asphalt specimen reduced to 50% of initial amount. Up to a 1,000,000 cycles of loading were applied to each specimen.

Different …

High Temperature Oxidation Characteristics Of Nb-10w-Xcr Alloys, Maria Del Pilar Moricca

Open Access Theses & Dissertations

The use of refractory metals in high temperature applications has been attractive for several years. Systems based on niobium represent a potential new generation of refractory materials systems because of their low density, high melting points, and strength at elevated temperatures. Despite these desirable characteristics, the widespread use of niobium-based alloys is limited because its oxidation resistance is still inadequate for structural applications. Understanding the oxidation kinetics of Nb-based alloys and the role of the different phases in the oxidation process is of crucial importance to improve the oxidation resistance of these materials.

The effect of Cr content on the …

Microstructural Characterization Of Overaged Gtd-111 Hp Turbine Buckets, Oscar Quintero

Open Access Theses & Dissertations

Superalloys are metallic materials that exhibit excellent mechanical strength and creep resistance at high temperatures. They have good surface stability and are corrosion resistant. Superalloys are mostly used in the aerospace industry, gas turbine engines and blades (hot zones of gas turbines), and where extreme heat is encountered. The focus of this research was on the GTD-111 Ni-base superalloy, which is a General Electric (GE) proprietary superalloy mostly used in gas turbine blades with the form of high pressure or first stage buckets. This alloys features better mechanical properties, creep resistance, and a higher stress rupture temperature than the commonly …