Mechanics of Materials Commons^™

Magnetic Field-Induced Transformation In Polycrystalline Ni2mnal Heusler Type Magnetic Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The martensitic and magnetic transformations, as well as the mechanical properties, of Ni₂MnAl alloys in as-cast (AC) and heat-treated (HT) conditions were investigated. Magnetic-field-induced strain was evaluated via magnetostriction, with reversible strains of 0.14% and 0.2% achieved in the martensitic phase at 2 K for the AC and HT alloys, respectively. Transformation temperatures and Curie temperatures were determined under constant applied magnetic field, revealing that γ-phase inclusions in the AC microstructure suppress antiferromagnetic domain response, yielding a lower magnetization (∼8.4 emu g⁻¹) compared to the HT alloy (∼13.4 emu g⁻¹). Both alloys exhibited hysteretic behavior in the martensitic state and …

Creation Of The 2-Way Cross Laminated Timber Subroutine For Computing Dynamic Analysis Parameters, Joseph Freitas

Architectural Engineering

This document will describe the inputs, methodology, and outputs for the CLT 2-way subroutine for cases with and without openings recently added to a proprietary structural analysis software. For the sake of simplicity, most of the discussion will be focused on cases without openings from here on out, as the verification process for a novel method for cases with openings is still in progress. The CLT 2-way module calculates multi-point resistance functions for panels without openings by automating the procedure outlined in an industry-standard structural design manual. The subroutine also finds the appropriate dynamic response factors, kinetic load multipliers, mass, …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Discrete Element Modeling Of Granular Soils: Critical State Behavior Applied To Impact Pile Driving, Esteban Patino Marin

Graduate Studies Theses and Dissertations 2026

This thesis investigates the use of the Discrete Element Method (DEM) to study two complementary aspects of granular soil mechanics: critical state behavior of granular materials and dynamic response of driven piles in sand, both of which are governed by the same particle-scale mechanisms of dilation, contraction, and fabric evolution.

The first examines the critical state behavior and fabric anisotropy of granular soils through DEM simulations of direct shear, direct simple shear, and true triaxial tests. Sphere-cluster particles representative of a uniform sand are used in two assemblages of approximately twenty-five thousand and one hundred twenty-five thousand spheres to evaluate …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Experimental And Numerical Investigation On The Effect Of Projectile Mass And Apex Angle On Penetration Depth Into Sandy Soils, Abdul-Rahman K. Osman, Ahmed Elshesheny Dr, Mohamed S. Zahran Dr, Nabil M. Nagy Prof.

Journal of Engineering Research

Projectile penetration in granular soils remains a critical concern in defense engineering and ballistics research. This study presents an experimental and numerical investigation of rigid cone-tip projectile penetration into very dense sand, examining the influence of apex angle and projectile weight on penetration depth. Laboratory experiments were conducted using metallic projectiles with apex angles of 10°, 30°, 60°, and 90° and weights of 2.445, 3.87, 5.33, and 6.81 kg, dropped from a height of 4.295 m into a 500×500×500 mm wooden tank filled with sand to 400 mm height at 95% relative density. Through systematic testing, two empirical correlation …

Application Of Distributed Fiber Optic Sensing (Dfos) For Monitoring Asphalt Pavement Strains Under Accelerated Loading Conditions, Sebastian Morales

Open Access Theses & Dissertations

This thesis presents a study on the application of Distributed Fiber Optic Sensing (DFOS) technology for detecting pavement's strain response with high spatial resolution. Using a Rayleigh-based optical frequency domain reflectometry (OFDR) system, DFOS sensors were calibrated and embedded in full-scale asphalt slabs subjected to accelerated loading using a Model Mobile Load Simulator 3 (MMLS3). Calibration of the DFOS sensors was conducted using a three-point bending flexural test with known load conditions and reference strain gauges to validate theoretical and numerical models. The results demonstrate DFOS's capability to detect pavement response under static and dynamic loading, as well as changes …

Ultimate Limit State Reliability-Based Approach Life Prediction Of An Existing Frame Structure Under Seismic Hazard In Indonesia, Wira Herucakra, Luh Putri Adnyani

Journal of Materials Exploration and Findings

Life assessment integrated with Structural Integrity Management (SIM) has been implemented in the oil and gas industry for the past decade to maintain the integrity and safety of an in-service structure used to support hydrocarbon exploration, production, and processing activity. Current structural life assessment, as ruled by the American Petroleum Institute (API), uses a fatigue-based approach for offshore structures subjected to wave loading. As the general principle of SIM is not limited to offshore structures, this study offers an alternative life assessment method for onshore structures, especially steel frame structures subjected to earthquake loads. Reliability analysis, combined with the effect …

Innovative Design Methodology For Durable Open-Graded Friction Course Asphalt Mixtures, Anas Abualia

LSU Doctoral Dissertations

Open-graded friction course (OGFC) is a thin asphalt mixture surface layer with a high percentage of coarse aggregates and high interconnected air voids, which provides improved skid resistance, visibility, and decreased pavement-tire noise. However, construction personnel at DOTD reported that conventional OGFC mixtures have short service life (raveling distress). Further, their structural contribution to the pavement structure is commonly neglected and designed only for functionality purposes.

The objective of this study was to develop a rational mix design methodology to improve the durability of OGFC asphalt mixtures. Specific objectives are to: (1) conduct a rheological and chemical characterization of polymer-, …

Integrating Off-Spec Scms Into Plc Blends, George A. Qubty

Civil Engineering Theses - Archive

Off-spec supplementary cementitious materials (SCMs) remain underutilized due to variability in reactivity and non-conformance with existing standards. This study evaluates the hydration behavior and fresh-state and mechanical performance of these materials in Portland limestone cement (PLC) systems. One Class F fly ash (FA), one bottom ash (BA), and two calcined clays (HACC and LACC) were evaluated as 20 % replacements to PLC. Hydration behavior was characterized using isothermal calorimetry and thermogravimetric analysis (TGA), while fresh-state and mechanical performance were assessed through flow table, Vicat setting time, load–crack mouth opening displacement (CMOD) flexural testing, and compressive strength testing. HACC increased compressive …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

Micro-Mechanical Characterization Of Uhpc Stiffness Mechanisms: Towards A Better Understanding Of Concrete Elastic Modulus, Charissa N. Puttbach

Graduate Theses and Dissertations

Current design code equations for estimating the elastic modulus of specialty concretes like ultra-high performance concrete are not all suitable. Developing empirical curves from exhaustive experimental testing is challenging for concretes that may have high levels of cement replacement with mineral admixtures and fibers at varying volume contents. As such, an alternative approach is taken that seeks to understand the constituent microscale stiffness mechanisms and relate the results to the macroscale. Micropillars are fabricated on several cement paste phases using a focused ion beam. A modified pico-indenter is used to determine the linear and non-linear behavior under micro-compression loading. Micropillar …

Experimental And Finite Element Investigation Of Shear Transfer Mechanisms And Capacity Of Continuous Post-Tensioned Concrete Beams In One-Way Slab Buildings, Suman Rijal

Civil Engineering Theses - Archive

This study investigates the shear behavior and resistance mechanisms of continuous post-tensioned beams commonly used in one-way slab buildings. Combining experimental and analytical methods, the research focuses on the targeted failure regions of prestressed and non-prestressed continuous beams to gain deeper insights into their shear behavior. The large-scale specimens used in this study featured realistic parabolic tendon profiles and an average prestress level comparable to that used in actual construction. The experimental program includes three test series, with beam designs and setups refined for each series based on observations of shear crack development and progression in the preceding series. This …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan

College of Graduate Studies: Theses & Dissertations

The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …

Multi-Mode Regulation Of The Drying Process Of Industrial Gas, Isamidin Xakimovich Sidikov Pr, Nashvandova Gulruxsor Murot Qizi Phd

Technical science and innovation

Currently, much attention is paid to the issue of energy efficiency of gas processing enterprises. The continuous growth of world prices for energy resources requires constant improvement of the management system, providing the most optimal conditions for the flow of technological processes. A conceptual model of the heat-mass transfer process occurring in the absorber as an object of research has been developed, which characterizes the relationship of the variables involved in the drying process of natural gas, control, measurable and immeasurable, as well as controlled parameters have been selected, which are used to develop and study a mathematical model of …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

Meta-Analysis Of Insulated Concrete Wall Panel Design Methods For Shear And Flexure Behavior, Maryam Al-Bayati

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Insulated Concrete wall panels have been designed and constructed since the early 1950s with various shear ties, dimensions, and methods; nonetheless, thermal bridging and rational design are still a concern. Many companies have recently developed plastic connectors that have gradually replaced solid concrete sections and steel connectors due to their superior thermal efficiency and strength. However, there is no generally accepted method for predicting the behavior of sandwich wall panels in structural engineering practice or codes, but many methods have been used since the early 1920. This study aims to evaluate the accuracy of current methods for predicting the flexural …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

The Center For Centering Dome, Olek Piechaczek, Ryan M. Scharf

Architectural Engineering

The Center for Centering seeks to create a large-scale healing center, conducive to individual centering of the mind and body. This mobile installation provides a relaxing, enclosed space while still maintaining a connection to the outdoors. The clients liked the idea of having a pop-up installation that could be easily set up as a touring display. With a deadline for installation looming in June 2022, a team of students had five months to design and manufacture the structure.

In winter 2022, the students developed custom geometry to minimize the number of individual parts and built a ¼ scale model of …

Thermal Behavior Of Plain And Fiber-Reinforced Rigid Concrete Airfield Runways, Arash Karimi Pour

Open Access Theses & Dissertations

The environmental condition and temperature gradient are important factors resulting in concrete airfield runways cracking during the time. Rigid concrete airfield runways experience different thermal gradients during the day and night due to changes in air temperature. Curling and thermal expansion stresses are the main consequences resulting in various types of cracking over the surface and thickness of concrete airfield runways and increasing maintenance costs. The curvature of concrete slabs increases with an increase in the temperature gradient which is amplified when runways open to traffic. Additionally, the combination of the curling and shrinkage stresses, in rare circumstances, can be …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …