Mechanics of Materials Commons^™

Effect Of Process Parameter On Temperature Distribution, Microstructure, And Mechanical Properties Of Self-Reacting Friction Stir Welded Aluminum Alloy 6061-T651, Monica Adriana Torres

Open Access Theses & Dissertations

Self-reacting friction stir welding is the latest FSW tool configuration developed, it employs two shoulders--one on top and one on the bottom of the workpiece-- this tool configuration offers many advantages over conventional welding techniques. However, the current lack of information and specifications limits its understanding and application. This investigation analyzed the effect of process parameters on temperature distribution, microstructure evolution, and final mechanical properties of 6061-T651 SR-FS welds. A factorial experiment was carried out, in which three-process parameters were analyzed--rotational speed, travel speed, and tool plunge force-- three levels were analyzed for each parameter, except for a tool plunge …

Fabrication And Characterization Of Nanocrystalline Yttrium Oxide Thin Films For Electronic Device Applications, Mudavakkat Vikas Haridas

Open Access Theses & Dissertations

This thesis presents the optimization of growth conditions for fabricating nanocrystalline Yttrium Oxide (Y2O3) thin films on silicon and optical grade, high quality quartz substrates in order to study its structural, optical and electrical properties for electronic device applications.

Commercially Y2O3 has proven to be difficult to fabricate at high quality due to its high temperature growth requirements and the need to alter established fabrication methods for electronic devices. A high temperature requirement for high quality poses a problem for research and analysis. This calls upon for an optimization of the growth conditions to facilitate fabrication of thin films for …

The Effect Of Cr, Si And B On The Oxidation Behavior On Three Nb-Based Alloys, David Alvarez

Open Access Theses & Dissertations

Nb-based alloys are of particular interest to replace the current Ni-based superalloys for high-temperature structural applications. One important limitation to improve the efficiency of gas-turbine engines is the temperature limit of current materials being used. By allowing the temperature to increase, the efficiency will increase. Nb-based alloys have high melting points and adequate mechanical properties but the oxidation resistance is still inadequate.

This research focuses on the oxidation behavior of three Nb-based alloys to study the effect of Cr and Si variation and look at the effect of Boron. Boron can form a glassy borosilicate which is viscous at high …

Development And Characterization Of The Oxidation Behavior Of Various High Temperature Niobium Based Alloys, Benedict Isabel Portillo

Open Access Theses & Dissertations

The oxidation response of various niobium based refractory alloys from the Nb-Mo-Si-B-X alloy system has been examined at temperatures between 700 and 1400°C in air. The development of these alloys was part of an ongoing effort to develop and discover a new materials system capable of replacing nickel based super alloys. Additions of titanium were found to provide limited oxidation resistance. A discontinuous layer of TiO2 was observed to from at temperatures above 1100°C. Alloys containing titanium additions were observed to suffer from pest oxidation at low and intermediate temperatures due to the development of Nb2O5. Poor oxidation resistance at …

Achieving High Efficiency Laminated Polymer Solar Cell With Interfacial Modified Metallic Electrode And Pressure Induced Crystallization, Yongbo Yuan, Yu Bi, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

We report efficient laminated organic photovoltaic device with efficiency approach the optimized device by regular method based on Poly(3-hexylthiophene-2,5-diyl) and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM). The high efficiency is mainly attributed to the formation of a concrete polymer/metal interface mechanically and electrically by the use of electronic-glue, and using the highly conductive and flexible silver film as anode to reduce photovoltage loss and modifying its work function for efficiency hole extraction by ultraviolet/ozone treatment, and the pressure induced crystallization of PCBM.

In Vitro Models For Glaucoma Research: Effects Of Hydrostatic Pressure, Yuan Lei, Shadi Rajabi, Ryan M. Pedrigi, Darryl R. Overby, A. Thomas Read, C. Ross Ethier

Department of Mechanical and Materials Engineering: Faculty Publications

PURPOSE. The response of cells (e.g., optic nerve head [ONH] cells) to mechanical stress is important in glaucoma. Studies have reported the biological effects of hydrostatic pressure on ONH cells cultured on a rigid substrate. An apparatus, designed to independently vary hydrostatic pressure and gas tension (including oxygen tension) in culture medium, was used to evaluate the effects of pressure and tension on cell migration, shape, and α-tubulin architecture in a transformed cell line (DITNC1 rat cortical astrocytes).

METHODS. During the assay period, cells were exposed to one of four experimental configurations: (1) control pressure and control gas tension; (2) …

Impact Of Elliptical Trainer Ergonomic Modifications On Perceptions Of Safety, Comfort, Workout, And Usability For People With Physical Disabilities And Chronic Conditions, Judith M. Burnfield, Yu Shu, Thad W. Buster, Adam P. Taylor, Carl A. Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

Background The popularity of elliptical training has grown in rehabilitation, fitness, and home settings as a means for improving fitness and walking, yet many people with physical disabilities and chronic conditions experience difficulties when trying to use elliptical trainers.

Objective The purpose of this study was to compare, for people with disabilities and chronic conditions, perceptions of safety, comfort, workout, and usability of 4 elliptical trainers before and after the development of a set of low-cost adaptations.

Design This study was a quasi-experimental repeated-measures investigation.

Methods Twenty adults with diverse medical conditions and functional abilities evaluated 4 elliptical trainers for …

Use Of Environmental Scanning Electron Microscopy For In Situ Observation Of Interaction Of Cells With Micro- And Nanoprobes, Alexander Goponenko, B. J. Boyle, K. I. Jahan, Maxim V. Gerashchenko, Dmitri E. Fomenko, Vadim N. Gladyshev, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Precision intracellular sensing, probing and manipulation offer unprecedented opportunities for advances in biological sciences. Next-generation ultra-fine probes will be capable of targeting individual cell organelles. Development of such probes as well as probes capable of penetrating through tough cell walls requires detailed knowledge of cell-probe interaction. This Letter evaluated the applicability of environmental scanning electron microscopy (ESEM) for cell and cell-probe interaction imaging. Several types of cells (plant and yeast cells as well as mouse spermatozoa) were successfully imaged in their natural state, with mouse spermatozoa observed by ESEM for the first time. Computerized stage applied to image was tough …

Nanomechanical Analysis Of Insulinoma Cells After Glucose And Capsaicin Stimulation Using Atomic Force Microscopy, Ruiguo Yang, Ning Xi, King Wai-Chu Lai, Bei-Hua Zhong, Carmen Kar-Man Fung, Chen-Geng Qu, Donna H. Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Aim: Glucose stimulates insulin secretion from pancreatic islet β cells by altering ion channel activity and membrane potential in the β cells. TRPV1 channel is expressed in the β cells and capsaicin induces insulin secretion similarly to glucose. This study aims to investigate the biophysical properties of the β cells upon stimulation of membrane channels using an atomic force microscopic (AFM) nanoindentation system.

Methods: ATCC insulinoma cell line was used. Cell stiffness, a marker of reorganization of cell membrane and cytoskeleton due to ion channel activation, was measured in real time using an integrated AFM nanoindentation system. Cell height that …

Dispersive Wave Equations For Solids With Microstructure, A. Berezovski, Juri Engelbrecht, Mihhail Berezovski

Publications

The dispersive wave motion in solids with microstructure is considered in the one-dimensional setting in order to understand better the mechanism of dispersion. It is shown that the variety of dispersive wave propagation models derived by homogenization, continualisation, and generalization of continuum mechanics can be unified in the framework of dual internal variables theory.

Anomalous Loss Of Toughness Of Work Toughened Polycarbonate, Shawn E. Meagher

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Glassy polymers such as polycarbonate (PC) can be toughened through compressive plastic deformation. The increase in toughness is substantial, showing as much as a fifteen fold increase in the amount of dissipated energy during failure for samples compressed to 50% plastic strain. This toughness increase can be reversed through thermal aging at temperatures below the glass transition temperature (T_g = 147°C).

The combined effect of plastic compression and thermal aging has been studied using Charpy, Single Edge Notch Bending (SENB), and Compact Tension (CT) tests. The tests mapped the response of samples cut along different orientations relative to the …

Processing And Composition Effects On The Fracture Behavior Of Spray-Formed 7xxx Series Al Alloys, Mala M. Sharma, Constance W. Ziemian, Timothy J. Eden

Faculty Journal Articles

The fracture properties of high-strength spray-formed Al alloys were investigated, with consideration of the effects of elemental additions such as zinc,manganese, and chromium and the influence of the addition of SiC particulate. Fracture resistance values between 13.6 and 25.6 MPa (m)^1/2 were obtained for the monolithic alloys in the T6 and T7 conditions, respectively. The alloys with SiC particulate compared well and achieved fracture resistance values between 18.7 and 25.6 MPa (m)^1/2. The spray-formed materials exhibited a loss in fracture resistance (KI) compared to ingot metallurgy 7075 alloys but had an improved
performance compared to high-solute powder …

Deformation Waves In Microstructured Materials: Theory And Numerics, Juri Engelbrecht, Arkadi Berezovski, Mihhail Berezovski

Publications

A linear model of the microstructured continuum based on Mindlin theory is adopted which can be represented in the framework of the internal variable theory. Fully coupled systems of equations for macro-motion and microstructure evolution are represented in the form of conservation laws. A modification of wave propagation algorithm is used for numerical calculations. Results of direct numerical simulations of wave propagation in periodic medium are compared with similar results for the continuous media with the modelled microstructure. It is shown that the proper choice of material constants should be made to match the results obtained by both approaches

Diffuse Ultrasonic Scattering In Advanced Composites, Christer Stenström

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Non destructive testing (NDT) is a noninvasive technique used for characterization and inspection of the integrity of objects. NDT is an important tool for research, manufacturing monitoring and in-service inspections. Ultrasonic testing is the most used NDT technique, which for advanced composites can identify several types of defects, like delamination and interlaminar cracks. Diffuse ultrasonics has shown to be able to extract information at the microscale of metals and therefore it is believed it can be used for advanced composites to extract microstructural information, i.e. at the level of fibers.

In this thesis, diffuse ultrasonic methods, together with spatial variance …

Characterization, Modeling, And Consequences Of The Development During Plastic Flow Of Large Anisotropy In The Wave-Speeds, Quentin Fichot

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

There is a substantial change in the anisotropy of some glassy polymers when they are subjected to large plastic deformations. The most pronounced case probably is seen in polycarbonate (PC), which is a tough thermoplastic used for many structural applications, including as a protective transparent armor for such applications as bulletproof glass. This development of anisotropy in the elastic response can be of the same order as the applied strains, and, therefore, becomes important in problems that show substantial plastic flow. In spite of this, this characteristic of glassy polymers has not been included in the current models. We propose …

Elements Of Study On Dynamic Materials, Marine Rousseau, Gerard A. Maugin, Mihhail Berezovski

Publications

As a preliminary study to more complex situations of interest in small-scale technology, this paper envisages the elementary propagation properties of elastic waves in one-spatial dimension when some of the properties (mass density, elasticity) may vary suddenly in space or in time, the second case being of course more original. Combination of the two may be of even greater interest. Toward this goal, a critical examination of what happens to solutions at the crossing of pure space-like and time-like material discontinuities is given together with simple solutions for smooth transitions and numerical simulations in the discontinuous case. The effects on …

An Experimental Investigation Of Friction Bit Joining In Az31 Magnesium And Advanced High-Strength Automotive Sheet Steel, Rebecca Gardner

Theses and Dissertations

Friction Bit Joining (FBJ) is a recently developed spot joining technology capable of joining dissimilar metals. A consumable bit cuts through the upper layer of metal to be joined, then friction welds to the lower layer. The bit then snaps off, leaving a flange. This research focuses on FBJ using DP980 or DP590 steel as the lower layer, AZ31 magnesium alloy as the top layer, and 4140 or 4130 steel as the bit material. In order to determine optimal settings for the magnesium/steel joints, experimentation was performed using a purpose-built computer controlled welding machine, varying factors such as rotational speeds, …

Design, Fabrication, Structural Testing, And Numerical Analysis Of A Small Scale Composite Wing, Jacob David Gaunt, Juan Carlos Flores, Vincent Andrew Perry

Aerospace Engineering

A small scale composite wing based on a design found on an experimental aircraft was designed, constructed, and tested dynamically and statically. The wing was constructed similarly to an experimental aircraft wing. The performed static test was intended to produce pure bending. Strain gages were used to measure strains on the wing structure. The strains were converted to stresses to aid in analysis. The static test results suggested that the wing was actually under torsion. Four structural modes were found from the static test. A finite element analysis model was made to compare experimental results to numerical analytical results. The …

Coupled Dem-Fem For Dynamic Analysis Of Granular Systems In Bending, Kitti Rattanadit

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Characterizing the dynamic behavior of granular materials is one of the great challenges in the mechanics of granular matter. Methods for evaluating the mechanical properties of granular matter have applications in a variety of industries, mining and geotechnical activities, defense and military operations. A coupled 2D Discrete Element Method-Finite Element Method (DEM-FEM) code, called "BobKit", is developed and implemented for analyzing the behavior of a 2D granular layer on top of an elastic beam under deforming (quasi-static) or vibrating (dynamic) of the beam. The explicit time-integration dynamic code is used to simulate quasi-static and dynamic bending of the granular layer …

Multiscale Transformation Field Analysis Of Progressive Damage In Fibrous Laminates, Yehia Bahei-El-Din, Ritesh Khire, Prabhat Hajela

Centre for Advanced Materials

As part of an ongoing effort to model uncertainty propagation across multiple scales in fibrous laminates, this paper presents a deterministic transformation field analysis for modeling damage progression under membrane forces and bending moments. In this approach, equivalent eigenstresses are computed in the phases and/or plies such that their respective stress components that satisfy the underlying failure criteria are reduced to zero. Superposition of the solutions found for the undamaged laminate under applied loads and under the eigenstress field provide the entire response. Failure criteria are based on stress averages in the fiber and matrix. Damage mechanisms considered are frictional …

Modified Sandwich Structures For Improved Impact Resistance Of Wind Turbine Blades, Yehia Bahei-El-Din, Mostafa Shazly, I. El-Habbal, Y. Elbahy

Centre for Advanced Materials

Wind turbine blades are susceptible to damage due to fatigue as well as impact by flying objects and parts broken off failed blades of nearby wind towers. Localized, permanent compression of the foam core and delamination of the fibrous composite face sheets are typical damage modes and can lead to progressive structural failure. Sandwich structures modified by inclusion of flexible polyurethane (PU) layers within the cross section are examined under both impact and dynamic loads. Finite element models of sandwich structures with conventional and modified designs show that sandwich designs modified with PU interlayes exhibit reduced foam core crushing and …

Luminescence Enhancement Of Cdte Nanostructures In Laf3:Ce/Cdte Nanocomposites, Mingzhen Yao, Xing Zhang, Lun Ma, Wei Chen, Alan G. Joly, Jinsong Huang, Qingwu Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Radiation detection demands new scintillators with high quantum efficiency, high energy resolution, and short luminescence lifetimes. Nanocomposites consisting of quantum dots and Ce³⁺ doped nanophosphors may be able to meet these requirements. Here, we report the luminescence enhancement of LaF₃:Ce/CdTe nanocomposites which were synthesized by a wet chemistry method. CdTe quantum dots in LaF₃:Ce/CdTe nanocomposites are converted into nanowires, while in LaF₃ /CdTe nanocomposites no such conversion is observed. As a result, the CdTe luminescence in LaF₃:Ce/CdTe nanocomposites is enhanced about five times, while in LaF₃ /CdTe nanocomposites no enhancement was …

An Ab-Initio Study Of The Elastic Properties Of Important Group Iv Diborides At High Temperatures, Manny Gonzales

Open Access Theses & Dissertations

Presented is an ab-initio Molecular Dynamics (MD) study, employing the Density Functional Theory (DFT), of the lattice parameter, thermal expansion coefficients and elastic constants of ZrB₂, TiB₂ and HfB₂ as a function of temperature. The MD trajectories provide the equilibrium lattice parameters at finite temperatures, and the gradient of the energy from these equilibrium solutions is then used to calculate the components of the stiffness tensor. The results for ZrB₂ are shown to agree well with reported experimental results for the lattice parameters and elastic constants as a function of temperature.

Sensitivity Analysis Of The Johnson-Cook Plasticity Model For Hypervelocity Impacts: A Hydro-Code Study, Carlos David Castellanos

Open Access Theses & Dissertations

Computer simulations have been in use for decades in the modeling of hypervelocity impacts and general large deformation problems. Several computer codes have been developed to simulate this type of problems under a variety of geometric configurations and for any number of materials. These codes make use of several constitutive material models to simulate the response of the material under a variety of thermo-mechanical conditions. The Johnson-Cook constitutive model is widely used in the simulation hypervelocity impacts for the simulation of crater formation and even perforation of target structures. This thesis presents the results of a sensitivity study of this …

Selection Process, Modified Impact Testing And Failure Analysis Of An Electron-Beam-Melted Ti-6al-4v 3d Tessellation Based On The Eulerian Path Of The First Stellation Of The Rhombic Dodecahedron Open Unit Cell, Hugo Lopez

Open Access Theses & Dissertations

Ti-6Al-4V lattice block structures manufactured through the electron beam melting (EBM) process are a promising field in design and research due to great advantages that the alloy, the process and the final product offer. Three lattice block structures were manufactured through the electron beam process using an ARCAM A2 machine. The structures were designed using the MATERIALIZE^TM software and were designed around different types of unit cells. Compression testing was performed and one unit cell was selected due to its anisotropic behavior for modified impact testing. The same unit cell was used and it was scaled up to add …

Processing Of Zrb2-Zrc-Zrxsiy Ceramic By Reactive Metal Penetration, Nischel B. Maheswaraiah

Open Access Theses & Dissertations

The processing of ZrB2-ZrC-ZrxSiy composite by reactive metal penetration was investigated as a successor to the ZrB2-SiC composites for hypersonic vehicles application, which cannot be used for extended time at temperatures greater than 1600C due to formation of SiO and CO gases. Zirconium (Zr), zirconium disilicide (ZrSi2), and boron carbide (B4C) were reacted in graphite crucibles for 60, 120, 180, and 240 minutes. Microscopy and x-ray diffraction (XRD) deduced the formation of a heterogeneous microstructure of ZrB2-ZrC-ZrxSiy precipitates surrounded by a solidified Zr-Si melt. Unreacted boron carbide was observed in samples held at 1860C for 60 minutes and 120 minutes, …

Microstructure Investigation Of Al-Rich Titanium Aluminum Alloys, David Pham

Open Access Theses & Dissertations

The microstructures of Ti-Al alloys with 70-80 wt% Al were investigated. Aluminum wire (99.999%) and TiH₂ powder (99.7%) were used to produce the sample compositions inside a vertical tube furnace at 1600^oC in an Ar atmosphere. Argon is purified through a dehumidification and deoxidation system. Magnesium perchlorate Mg(ClO₄)₂ acts as a desiccant and titanium sponge pulls oxygen from the Ar in furnaces operating at 800^oC and 750^oC. X-ray diffraction and an optical microscope are used to identify phases and compositions

Spectroscopic Study Of The Inhibition Of Calcium Oxalate Calculi By Larrea Tridentata, Luis Alonso Pinales

Open Access Theses & Dissertations

The causes of urolithiasis include such influences as diet, metabolic disorders, and genetic factors which have been documented as sources that aggravate urinary calculi depositions and aggregations, and, implicitly, as causes of urolithiasis. This study endeavors to detail the scientific mechanisms involved in calcium oxalate calculi formation, and, more importantly, their inhibition under growth conditions imposed by the traditional medicinal approach using the herbal extract, Larrea tridentata. The calculi were synthesized without and with Larrea tridentata infusion by employing the single diffusion gel technique. A visible decrease in calcium oxalate crystal growth with increasing amounts of Larrea tridentata herbal infusion …

The Reactivity Of A Zr-Si Melt With B4c At Ultrahigh Temperatures, Alvaro Vega Sandate

Open Access Theses & Dissertations

Surfaces with exceptional properties are needed for next generation materials. Hypersonic re-entry space vehicles or turbines are subjected to both oxidizing and neutral environments and nose-caps or wings on such vehicles could easily reach operating temperatures of over 2000°C. Ultrahigh temperature ceramics like ZrB2 and HfB2 have melting temperatures of 3245°C and 3380°C respectively. However, these materials need to be protected from oxidation, usually with an oxide layer. Zirconium is more affordable and will be used to study its reaction with B4C and ZrSi2.

Experimentation was conducted by melting Zr slugs into a B4C and ZrSi2 packed bed at 1860°C …

Resistive Switching Of Tin Dioxide (Sno2) For Memristor Applications, Sergio Fabian Almeida

Open Access Theses & Dissertations

In the last decades new electrical devices have been investigated in order to overcome problems caused by integrated circuit shrinking. Within these devices there is one that has attracted much attention due to its high scalability and simple structure. This device was proposed theoretically by Leon Chua in 1971 who gave it the name of "Memristor". In the recent years thin films structures composed of a metal/oxide/metal (MOM) stack have been linked to this new device, also known as "Resistive switching". There are several applications for the memristor; one of the most important is for resistive random access memory (ReRAM) …