Mechanics of Materials Commons^™

Emergent De Sitter Expansion And Closed Topology From The Cosmic Fabric Model As An Open Thermodynamic System: Resolving The Negative Bulk Modulus Paradox, T G. Tenev, C B. Ward, T F. Tenev, M F. Horstemeyer

Faculty Publications and Presentations

The Cosmic Fabric Model establishes a continuum-mechanics isomorphism to General Relativity by representing physical space as an elastic three-dimensional hyperplate embedded in a four-dimensional spatial bulk. Reproducing vacuum kinematics requires a vanishing P-wave modulus, which in turn implies a negative bulk modulus—an apparent thermodynamic instability in a closed system. This paradox is resolved by recasting the framework as an open system: the instability is not pathological but instead drives cosmic expansion. In this interpretation, the observable universe is a lower-energy solid formed through continuous solidification from a higher-dimensional precursor fluid. Using multiplicative kinematics from finite-growth mechanics, the model shows that …

Magnetic Field-Induced Transformation In Polycrystalline Ni2mnal Heusler Type Magnetic Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The martensitic and magnetic transformations, as well as the mechanical properties, of Ni₂MnAl alloys in as-cast (AC) and heat-treated (HT) conditions were investigated. Magnetic-field-induced strain was evaluated via magnetostriction, with reversible strains of 0.14% and 0.2% achieved in the martensitic phase at 2 K for the AC and HT alloys, respectively. Transformation temperatures and Curie temperatures were determined under constant applied magnetic field, revealing that γ-phase inclusions in the AC microstructure suppress antiferromagnetic domain response, yielding a lower magnetization (∼8.4 emu g⁻¹) compared to the HT alloy (∼13.4 emu g⁻¹). Both alloys exhibited hysteretic behavior in the martensitic state and …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Parts, Logan Trimmer

Harrisburg University Other Works

Presentation covering the broad strokes of the project. The goal was to prove the viability of hybrid/additive manufacturing for high stress automotive applications. This project focused on recreating a piston from an old engine to examine if hybrid manufacturing could be used for such applications. On a small scale, hybrid manufacturing was able to be more cost effective if the costs of the equipment and electricity were ignored. The decision to ignore those costs came from the inability to find accurate prices for industrial casting.

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Components, Logan Trimmer

Harrisburg University Other Works

The goal of this research was to establish the viability of using hybrid manufacturing for automotive applications. By verifying that high-stress components can be created, it can be assumed that any other lower stress part could be made to match the strength requirements. A limiting factor of adoption for hybrid manufacturing is how new the technology is. Studies on time and cost were performed allowing for comparisons with traditional manufacturing technologies (casting, forging, milling) used in automotive applications. This research utilized a Haas Automation UMC750 5-axis CNC mill with a Meltio laser wire direct energy deposition attachment. Fusion 360 was …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Characterization Of The Fatigue Threshold Behavior Of Uhmwpe, Bethany B. Smith, Anurag Roy, Robert O. Ritchie, Lisa A. Pruitt

Faculty Journal Articles

Ultra-high-molecular-weight-polyethylene (UHMWPE) has been the material of choice for bearings in total joint replacements (TJRs) for decades as a result of its excellent wear resistance, chemical inertness, energetic toughness, low friction, and biocompatibility. Utilization of this polymer in orthopedic devices requires oxidation, wear, and fatigue resistance. Balancing these important properties by tailoring processing techniques and modulating microstructural features has been an ongoing endeavor in the field. Research into the clinical applications of UHMWPE has primarily focused on the challenges of wear and oxidation while studies into the realm of fatigue have been more limited. Literature gaps exist in fully understanding …

Modeling Degradation In Li-Ion Batteries: Analyzing Single-Cell Degradation And Applying It To Customized Pack-Level, Mohannad Y. Alkhalil

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

The rapid expansion of lithium-ion (Li-ion) battery applications in areas such as electric vehicles (EVs), renewable energy storage, and portable electronics has drawn attention to the need for improving their performance, safety, and longevity. As Li-ion batteries become essential across technologies, understanding degradation mechanisms is critical for optimizing design and ensuring reliable operation. This work provides a detailed overview of modeling degradation in Li-ion batteries, focusing on single-cell behavior and its implications for pack-level performance.

The PyBaMM (Python Battery Mathematical Modeling) package, an open-source battery simulation tool written in Python, is used for single-cell simulations. Liionpack, another Python-based library, is …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Deep-Learning Based Microstructure Reconstruction And Generation, Cameron J. Maloney, Lucas Taliaferro

College of Engineering Summer Undergraduate Research Program

Characterizing the microstructural behavior of materials is crucial for understanding their properties and performance. Traditional imaging methods, such as optical microscopy and electron microscopy, are effective but costly and time-consuming. Computational approaches can reduce costs and time while expanding the accessibility of microstructural analysis through the generation of new microstructure images. Traditional computational approaches, namely descriptor-based approaches, are slow but effective in low-data scenarios. Modern approaches use machine learning (ML), which is faster but often requires a lot of data to approach the performance of descriptor-based methods. This research leverages a special data-efficient Generative Adversarial Network (GAN) architecture to artificially …

Tension–Compression Fatigue Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Marina B. Ruggles-Wrenn, Joshua Schmidt

Faculty Publications

Fully reversed tension–compression fatigue of a hybrid material comprising polymer matrix composite (PMC) co-cured with a ceramic matrix composite (CMC) was investigated. The PMC portion had a polyimide matrix reinforced with 15 plies of carbon fibers woven in an eight-harness satin weave (8HSW). The CMC portion had three plies of a quartz-fiber 8HSW fabric in a zirconia-based ceramic matrix. The hybrid PMC/CMC was developed for use in aerospace thermal protection systems (TPS). Hence, the experimental setup aimed to simulate the TPS service environment—the CMC side was kept at 329 °C, whereas the PMC side was open to laboratory air. Compression …

A First Step Towards Understanding Thermomechanical Behavior Of The Nb-Cr System Through Interatomic Potential Development And Molecular Dynamics Simulations, Lucas A. Heaton, Adib J. Samin

Faculty Publications

Utilizing a preliminary interatomic potential, this work represents an initial exploration into the thermomechanical behavior of NbCr solid solutions. Specifically, it examines the effect of different amounts of Cr solute, for which information in the literature is limited. The employed interatomic potential was developed according to the embedded atom model (EAM), and was trained on data derived from density functional theory calculations. While the potential demonstrated reasonable accuracy and predictive power when tested, various results highlight deficiencies and encourage further development and training. Mechanical strength, heat capacities, thermal expansion coefficients, and thermal conductivities were found to decrease with Cr content. …

A Multi-Material Platform For Imaging Of Single Cell-Cell Junctions Under Tensile Load Fabricated With Two-Photon Polymerization, Jordan Rosenbohm, Grayson Minnick, Bahareh Tajvidi Safa, Amir M. Esfahani, Xiaowei Jin, Haiwei Zhai, Nickolay V. Lavrik, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We previously reported a single-cell adhesion micro tensile tester (SCAμTT) fabricated from IP-S photoresin with two-photon polymerization (TPP) for investigating the mechanics of a single cell-cell junction under defined tensile loading. A major limitation of the platform is the autofluorescence of IP-S, the photoresin for TPP fabrication, which significantly increases background signal and makes fluorescent imaging of stretched cells difficult. In this study, we report the design and fabrication of a new SCAμTT platform that mitigates autofluorescence and demonstrate its capability in imaging a single cell pair as its mutual junction is stretched. By employing a two-material design using IP-S …

Injectable And Rapidly Expandable Thrombin-Decorated Cryogels Achieve Rapid Hemostasis And High Survival Rates In A Swine Model Of Lethal Junctional Hemorrhage, Syed Muntazir Andrabi, S.M. Shatil Shahriar, Al-Murtadha Al-Gahmi, Benjamin L. Wilczewski, Mark A. Carlson, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Effective therapies are urgently needed to stabilize patients with marginally compressible junctional hemorrhage long enough to get them to the hospital alive. Herein, we report injectable and rapidly expandable cryogels consisting of polyacrylamide and thrombin (AT cryogels) created by cryo-polymerization for the efficient management of lethal junctional hemorrhage in swine. The produced cryogels have small pore sizes and highly interconnected porous architecture with robust mechanical strength. The cryogels exhibit rapid shape memory properties and prove to be resilient against fatigue. These cryogels also show high water/blood absorption capacity, fast blood clotting effect, and enhanced adhesion of red blood cells and …

Copper−Cystine Biohybrid-Embedded Nanofiber Aerogels Show Antibacterial And Angiogenic Properties, Anik Karan, Navatha S. Polavaram, Margarita Darder, Yajuan Su, Syed Muntazir Andrabi, S M Shatil Shahriar, Johnson V. John, Zeyu Luo, Mark A. Decoster, Yu Shrike Zhang, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Copper−cystine-based high aspect ratio structures (CuHARS) possess exceptional physical and chemical properties and exhibit remarkable biodegradability in human physiological conditions. Extensive testing has confirmed the biocompatibility and biodegradability of CuHARS under diverse biological conditions, making them a viable source of essential Cu²⁺. These ions are vital for catalyzing the production of nitric oxide (NO) from the decomposition of Snitrosothiols (RSNOs) found in human blood. The ability of CuHARS to act as a Cu²⁺ donor under specific concentrations has been demonstrated in this study, resulting in the generation of elevated levels of NO. Consequently, this dual function makes …

Implantation Of A Capsular Tension Ring During Cataract Surgery Attenuates Predicted Remodeling Of The Post-Surgical Lens Capsule Along The Visual Axis, Kurt A. Ameku, Caleb C. Berggren, Ryan M. Pedrigi

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Cataract surgery permanently alters the mechanical environment of the lens capsule by placing a hole in the anterior portion and implanting an intraocular lens (IOL) that has a very different geometry from the native lens. We hypothesized that implant configuration and mechanical interactions with the post-surgical lens capsule play a key role in determining long-term fibrotic remodeling.

Methods: We developed the first finite element-growth and remodeling (FE-G&R) model of the post-surgical lens capsule to evaluate how implantation of an IOL with and without a capsular tension ring (CTR) impacted evolving lens capsule mechanics and associated fibrosis over …

Engineering Neurotoxin-Functionalized Exosomes For Targeted Delivery To The Peripheral Nervous System, Mena Asha Krishnan, Olawale A. Alimi, Tianshu Pan, Mitchell Kuss, Zeljka Korade, Guoku Hu, Bo Liu, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

The administration of therapeutics to peripheral nerve tissue is challenging due to the complexities of peripheral neuroanatomy and the limitations imposed by the blood–nerve barrier (BNB). Therefore, there is a pressing need to enhance delivery effectiveness and implement targeted delivery methods. Recently, erythrocyte-derived exosomes (Exos) have gained widespread attention as biocompatible vehicles for therapeutics in clinical applications. However, engineering targeted Exos for the peripheral nervous system (PNS) is still challenging. This study aims to develop a targeted Exo delivery system specifically designed for presynaptic terminals of peripheral nerve tissue. The clostridium neurotoxin, tetanus toxin-C fragment (TTC), was tethered to the …

Yap Mechanotransduction Under Cyclic Mechanical Stretch Loading For Mesenchymal Stem Cell Osteogenesis Is Regulated By Rock, Eunju Kim, Brandon D. Riehl, Tasneem Bouzid, Ruiguo Yang, Bin Duan, Henry J. Donahue, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

While yes-associated protein (YAP) is now recognized as a potent mechanosensitive transcriptional regulator to affect cell growth and differentiation including the osteogenic transcription of mesenchymal stem cells (MSCs), most studies have reported the YAP mechanosensing of static mechanophysical cues such as substrate stiffness. We tested MSC response to dynamic loading, i.e., cyclic mechanical stretching, and assessed YAP mechanosensing and resultant MSC osteogenesis. We showed that cyclic stretching at 10% strain and 1 Hz frequency triggered YAP nuclear import in MSCs. YAP phosphorylation at S127 and S397, which is required for YAP cytoplasmic retention, was suppressed by cyclic stretch. We also …

Mechanics Of Pure Bending And Eccentric Buckling In High-Strain Composite Structures, Jimesh D. Bhagatji, Oleksandr G. Kravchenko, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This paper presents fabrication, experimental testing, and progressive failure modeling to study the deformation of an ultra-thin composite beam. The research study examines the deformation modes of a post-deployed boom under repetitive pure bending loads using a four-point bending setup and …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. The end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Exploring Regular And Turbulent Flow States In Active Nematic Channel Flow Via Exact Coherent Structures And Their Invariant Manifolds, Caleb G. Wagner, Rumayel H. Pallock, Jae Sung Park, Michael M. Norton, Piyush Grover

Department of Mechanical and Materials Engineering: Faculty Publications

This work is a unified study of stable and unstable steady states of 2D active nematic channel flow using the framework of Exact Coherent Structures (ECSs). ECSs are stationary, periodic, quasiperiodic, or traveling wave solutions of the governing equations that, together with their invariant manifolds, organize the dynamics of nonlinear continuum systems. We extend our earlier work on ECSs in the preturbulent regime by performing a comprehensive study of stable and unstable ECSs for a wide range of activity values spanning the preturbulent and turbulent regimes. In the weakly turbulent regime, we compute more than 200 unstable ECSs that coexist …

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

What Does It Mean To Be “Prepared For Work”? Perceptions Of New Engineers, Jessica R. Deters, Marie C. Paretti, Logan A. Perry, Robin Ott

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Engineering education seeks to prepare students for engineering practice, but the concept of preparedness is often ill-defined. Moreover, findings from studies of different populations or in different contexts vary regarding how well new graduates are prepared. These variations, coupled with the lack of clarity, suggest the need to better understand what it means to be prepared for engineering work.

Purpose: This study contributes to research on workplace preparation by exploring how new graduates describe being prepared for engineering work.

Method: Applying secondary analysis to data from the multi-institution Capstone To Work (C2W) project, we used thematic …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

Meta-Analysis Of Insulated Concrete Wall Panel Design Methods For Shear And Flexure Behavior, Maryam Al-Bayati

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Insulated Concrete wall panels have been designed and constructed since the early 1950s with various shear ties, dimensions, and methods; nonetheless, thermal bridging and rational design are still a concern. Many companies have recently developed plastic connectors that have gradually replaced solid concrete sections and steel connectors due to their superior thermal efficiency and strength. However, there is no generally accepted method for predicting the behavior of sandwich wall panels in structural engineering practice or codes, but many methods have been used since the early 1920. This study aims to evaluate the accuracy of current methods for predicting the flexural …