Mechanics of Materials Commons^™

Greek Key-Inspired Fractal Metamaterials With Enhanced Flexibility And Energy Absorption., Zhennan Zhang

Electronic Theses and Dissertations

Architected materials with intricate three-dimensional (3D) geometries offer unique properties and functionalities but face challenges in manufacturing costs and complexity. This research explores the integration of simple 2D Greek Key-inspired lattices into fractal designs to achieve exceptional mechanical performance. Using 3D printing and kerfing, these fractal structures demonstrate enhanced flexibility and energy absorption capabilities. Through three-point bending and in-plane tensile tests, the 2D fractal lattices exhibited a 600-fold reduction in bending force and a tensile stretch capacity of up to 520%, significantly outperforming brittle parent materials. Out-of-plane compression tests revealed a five-fold increase in energy absorption compared to honeycomb structures, …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Optical Direct Detection Of Thermal Vibrations Of Ultralow Stiffness Micro-Nano Structures., Sri Sukanta Chowdhury

Electronic Theses and Dissertations

A direct detection optical vibrometer is constructed around an 850 nm laser and a quadrant photodetector (QPD). The limit of detection is 0.2 fW which corresponds to a minimum amplitude of 0.1 Å. The vibrometer is used to measure the thermal vibration spectra of low stiffness micromechanical structures have nanometer features. One structure measured is a cantilevered 30 μm diameter glass fiber. Vibration amplitudes as low as 1.1 Å are measured. The thermal vibration spectra show fundamental resonances at 80-250 Hz and a signal to noise ratio (SNR) of 23-55 dB. Young’s modulus of glass in the cantilevers, estimated from …

Modeling And Validations Of Control Parameters For Material Extrusion-Based Additive Manufacturing Of Thixotropic Aluminum Alloys., Lars Herhold

Electronic Theses and Dissertations

Additive Manufacturing (AM) with metals has been accomplished mainly through powder bed fusion processes. Initial experiments and simulations using Material Extrusion Additive Manufacturing (MEAM) have been performed by various researchers especially using low melting alloys. Recently Stratasys Inc. submitted a patent application for the use of their Material Extrusion technology also called Fused Deposition Modeling (FDM) where they describe the process using thixotropic semi-solid alloys. Currently this process using semi-solid, engineering type alloys such as A356 or THIXALLOY 540 aluminum have not been researched to evaluate the control parameters. This research combines the in-depth knowledge of applying thixotropic semi-solid aluminum …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Freeze-Thawing Of Polyester/E-Glass As An Evaluation Of An Astm International Test Standard Proposal, Stefan Mauritz Strandlund

Electronic Theses and Dissertations

American Composites Manufacturers Association (ACMA) reported in 2009 that the four major sectors currently utilizing fiber reinforced polymers (FRP) are construction, corrosion, marine, and transportation in descending order of total FRP shipped. All of these sectors are known to be billion dollar industries and they are all involved with applications subjected to freezing and thawing. FRP encompass many characteristics that are beneficial to these sectors and also in resisting this exposure. ASTM International has yet not developed a standard to test FRP materials resistance to freeze-thaw (FT) cycling exposure. The D20.18.02 committee of the ASTM is in the process of …

The Investigation Of Nano Silica In The Cement Hydration Pro, Jonathan Samuel Belkowitz

Electronic Theses and Dissertations

With the advent of nano technology, materials have been developed that can be applied to high performance concrete mix designs. Nano silica reacts with calcium hydroxide (CH) to develop more of the strength carrying structure of cement: calcium silica hydrate (CSH). In this paper, relationships have been developed to distinguish the benefits when using different sizes of nano silica in cement paste. An extensive regime of experimental analysis was carried out to determine the effect of nano silica. Through these experiments the heat of hydration of multiple cement mix designs was measured. After that, the concentration of CH was recorded …