Mechanics of Materials Commons^™

Thickness-Shear And Thickness-Twist Modes In An Oblate Elliptical Ceramic Cylinder And Energy Trapping In Contoured Acoustic Wave Resonators, Huijing He, Jiashi Yang, Yi-Hua Huang

Department of Mechanical and Materials Engineering: Faculty Publications

We study shear-horizontal motions of a piezoelectric ceramic cylinder with an oblate elliptical cross section and axial poling. Exact thickness-shear and thickness-twist vibration modes are obtained. These modes show energy trapping, i.e., the vibration is mainly confined near the thick, central region and decays to almost nothing near the edges. The results are useful for the understanding and design of contoured piezoelectric resonators for strong energy trapping.

Systems And Synthetic Biology Of The Vessel Wall, Jennifer Frueh, Nataly Maimari, Ying Lui, Zoltan Kis, Vikram Mehta, Negin Pormehr, Calum Grant, Emmanuel Chalkias, Mika Falck-Hansen, Sandra Bovens, Ryan M. Pedrigi, Taka Homma, Gianfillippo Coppola, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

Atherosclerosis is intimately coupled to blood flow by the presence of predilection sites. The coupling is through mechanotransduction of endothelial cells and approximately 2000 gene are associated with this process. This paper describes a new platform to study and identify new signalling pathways in endothelial cells covering an atherosclerotic plaque. The identified networks are synthesized in primary cells to study their reaction to flow. This synthetic approach might lead to new insights and drug targets.

Nanotopographic Cell Culture Substrate: Polymer-Demixed Nanotextured Films Under Cell Culture Conditions, Jung Yul Lim, Christopher A. Siedlecki, Henry J. Donahue

Department of Mechanical and Materials Engineering: Faculty Publications

Modulating physical cell culture environments via nanoscale substrate topographic modification has recently been of significant interest in regenerative medicine. Many studies have utilized a polymer-demixing technique to produce nanotextured films and showed that cellular adhesion, proliferation, and differentiation could be regulated by the shape and scale of the polymer-demixed nanotopographies. However, little attention has been paid to the topographic fidelity of the polymer-demixed films when exposed to cell culture conditions. In this brief article, two polymer-demixing systems were employed to assess topographic changes in polymer-demixed films after fibronectin (FN) extracellular matrix protein adsorption and after incubation in phosphate-buffered saline at …

Usability Assessment Of Two Different Control Modes For The Master Console Of A Laparoscopic Surgical Robot, Xiaoli Zhang, Carl A. Nelson, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this study is to evaluate potential interface control modes for a compact fourdegree- of-freedom (4-DOF) surgical robot. The goal is to improve robot usability by incorporating a sophisticated haptics-capable interface. Two control modes were developed using a commercially available haptic joystick: (1) a virtually point-constrained interface providing an analog for constrained laparoscopic motion (3-DOF rotation and 1-DOF translation), and (2) an unconstrained Cartesian input interface mapping more directly to the surgical tool tip motions. Subjects (n = 5) successfully performed tissue identification and manipulation tasks in an animal model in point-constrained and unconstrained control modes, respectively, with …

Tool Sequence Trends In Minimally Invasive Surgery: Statistical Analysis And Implications For Predictive Control Of Multifunction Instruments, Carl A. Nelson, Evan Luxon, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents an analysis of 67 minimally invasive surgical procedures covering 11 different procedure types to determine patterns of tool use. A new graph-theoretic approach was taken to organize and analyze the data. Through grouping surgeries by type, trends of common tool changes were identified. Using the concept of signal/noise ratio, these trends were found to be statistically strong. The tool-use trends were used to generate tool placement patterns for modular (multi-tool, cartridge-type) surgical tool systems, and the same 67 surgeries were numerically simulated to determine the optimality of these tool arrangements. The results indicate that aggregated tool-use data …

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …

Generic Strategies To Implement Material Grading In Finite Element Methods For Isotropic And Anisotropic Materials, Ke Yu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

We look at generic strategies to transfer material grading into finite element methods. Three strategies are proposed to transfer material grading into the finite element analysis. These strategies are node-centered, element-centered, and the definition of material grading through external functions. The process to achieve each strategy is stated, and examples are used to illustrate each strategy, and to compare them. The strategies are implemented in finite-deformation nonlinear elastic analysis.

Several examples are used to illustrate the implementation of each strategy for graded isotropic materials. For these examples, the results obtained from finite element models are compared with those obtained from …

Thickness-Shear And Thickness-Twist Vibrations Of An At-Cut Quartz Mesa Resonator, Huijing He, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness-shear and thickness-twist vibrations of an AT-cut quartz plate mesa resonator with stepped thickness. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes, and energy trapping are calculated and examined. The solution shows that a mesa resonator exhibits strong energy trapping of thickness-shear and thickness-twist modes, and that the trapping is sensitive to some of the structural parameters of the resonator.

In Vivo Three-Dimensional Blood Velocity Profile Shapes In The Human Common, Internal, And External Carotid Arteries, Alexey Kamenskiy, Yuris A. Dzenis, Jason N. Mactaggart, Anastasia Desyatova, Iraklis I. Pipinos

Department of Mechanical and Materials Engineering: Faculty Publications

Objective: True understanding of carotid bifurcation pathophysiology requires a detailed knowledge of the hemodynamic conditions within the arteries. Data on carotid artery hemodynamics are usually based on simplified, computer-based, or in vitro experimental models, most of which assume that the velocity profiles are axially symmetric away from the carotid bulb. Modeling accuracy and, more importantly, our understanding of the pathophysiology of carotid bifurcation disease could be considerably improved by more precise knowledge of the in vivo flow properties within the human carotid artery. The purpose of this work was to determine the three-dimensional pulsatile velocity profiles of human carotid arteries. …

Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer

Master's Theses

The objective of this thesis is to develop vibration-based fault detection strategies for on-line condition monitoring of gear transmission systems. The study divides the thesis into three sections. First of all, the local stresses created by a root fatigue crack on a pinion spur gear are analyzed using a quasi-static finite element model and non-linear contact mechanics simulation. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. The second section is dedicated to fixed axis power trains. Torsional vibration …

Two-Scale Microstructure Dynamics, Arkadi Berezovski, Mihhail Berezovski, Juri Engelbrecht

Publications

Wave propagation in materials with embedded two different microstructures is considered. Each microstructure is characterized by its own length scale. The dual internal variables approach is adopted yielding in a Mindlin-type model including both microstructures. Equations of motion for microstructures are coupled with the balance of linear momentum for the macromotion, but not coupled with each other. Corresponding dispersion curves are provided and scale separation is pointed out.

Rehabilitation And Exercise Machine, Judith M. Burnfield, Yu Shu, Adam P. Taylor, Thad W. Buster, Carl Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness.

Effects Of Mass Layer Dimension On A Finite Quartz Crystal Microbalance, Y. P. Kong, Jinxi Liu, Huijing He, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this paper, we investigate free thickness-shear and thickness-twist vibrations of a finite crystal resonator of AT-cut quartz carrying a thin mass layer at the central portion of its top surface operating as a quartz crystal microbalance. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes and vibration confinement by the mass layer are calculated and examined.

Vertical Track Modulus Trending, Shane Michael Farritor, Sheng Lu

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for determining a trend in Vertical track modulus are disclosed in accordance with embodiments of the present invention. Vertical deflection data is collected along a particular section of railroad track. A first set of Vertical track modulus is determined, based in part, on the collected vertical deflection data. At a second time, vertical deflection data is again collected along the particular section of railroad track to be used in determining a second set of vertical track modulus. At least the first and second sets of Vertical track modulus are analyzed to determine a math ematical algorithm that …

The Effects Of Damage Arrestment Devices In Composite Plate Sandwiches With Fastener Holes, Mark Anderson, Nancy Hung Choy, Lacey Jones, Rita Kourskaya

Aerospace Engineering

Composite materials such as a carbon fiber are used in a variety of new technologies including aircraft, spacecraft, and motor vehicles. Carbon fiber has a high strength to weight ratio, a key advantage over other material options. This report discusses the use of composite damage arrestment devices (DADs) in composite sandwich panels with a foam core. There are three different curing cycles tested for the DADs: pressure only, vacuum only, and vacuum with 1000 lbs of pressure. Using a Tetrahedron Heat Press to cure the composite specimen and an Instron Machine to perform tensile testing, data was collected for each …

Analysis Of A Monolithic Crystal Plate Acoustic Wave Filter, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness–shear and thickness–twist vibrations of a finite, monolithic, AT-cut quartz plate crystal filter with two pairs of electrodes. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56 . An analytical solution is obtained using Fourier series from which the res-onant frequencies, mode shapes, and the vibration confinement due to the electrode inertia are calculated and examined.

Transverse Permeability Of Fibrous Porous Media, Ali Tamayol, Majid Bahrami

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, the transverse permeability of fibrous porous media is studied both experimentally and theoretically. A scale analysis technique is employed for determining the transverse permeability of various fibrous matrices including square, staggered, and hexagonal arrangements of unidirectionally aligned fibers, as well as simple two-directional mats and simple cubic structures. In the present approach, the permeability is related to the porosity, fiber diameter, and tortuosity of the medium. In addition, the pressure drop in several samples of tube banks of different arrangements and metal foams are measured in the creeping flow regime. The pressure-drop results are then used to …

Improved Rehabilitation And Exercise Machine / Machine De Reeducation Et D'Exercice Amelioree, Judith M. Burnfield, Adam Taylor, Thad W. Buster, Carla A. Nelson, Yu Shu

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness. An embodiment of the device includes a framework, a first and second crank arm, a first and second handle bar, a first and second foot pedal, a motor and pulley assembly, a first and second coupler link, and a motor controller with speed knob,

Waves In Microstructured Solids: A Unified Viewpoint Of Modelling, Arkadi Berezovski, Juri Engelbrecht, Mihhail Berezovski

Publications

The basic ideas for describing the dispersive wave motion in microstructured solids are discussed in the one-dimensional setting because then the differences between various microstructure models are clearly visible. An overview of models demonstrates a variety of approaches, but the consistent structure of the theory is best considered from the unified viewpoint of internal variables. It is shown that the unification of microstructure models can be achieved using the concept of dual internal variables.

On The Stability Of A Microstructure Model, Mihhail Berezovski, Arkadi Berezovski

Publications

The asymptotic stability of solutions of the Mindlin-type microstructure model for solids is analyzed in the paper. It is shown that short waves are asymptotically stable even in the case of a weakly non-convex free energy dependence on microdeformation.

Simulation Of Electrospun Nanofiber Deposition On Stationary And Moving Substrates, Linhua Liu, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Electrospinning produces continuous fibers with diameters from single nanometers to microns by jetting polymer solutions in high electric fields. Electrospun non-woven filamentary materials attract rapidly growing interest for broad range of applications. Properties of these materials depend on their nano- and microstructure that is determined in turn by the electric field and nanofiber collector. Despite critical importance, deposition of electrospun fibers on substrates has not yet been extensively studied theoretically and new methods of nanofiber collection continue to be developed mostly empirically. The objective of this Letter was to develop and demonstrate numerical simulation of electrospun nanofiber deposition on moving …

Modeling Of Solvent Evaporation From Polymer Jets In Electrospinning, Xiang-Fa Wu, Yury Salkovskiy, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Solvent evaporation plays a critical role in nanofiber formation in electrospinning. Here, we present a nonlinear mass diffusion-transfer model describing the drying process in dilute polymer solution jets. The model is used to predict transient solvent concentration profiles in polyacrylonitrile/ N,N-dimethylformamide (PAN/DMF) jets with the initial radii ranging from 50µm down to 100 nm. Numerical simulations demonstrate high transient inhomogeneity of solvent concentration over the jet cross-section in microscopic jets. The degree of inhomogeneity decreases for finer, submicron jets. The simulated jet drying time decreases rapidly with the decreasing initial jet radius, from seconds for microjets to single milliseconds for …

Preparation And Characterization Of Iron Oxide And Hydroxide Based Nanomaterials, Guillermo Carbajal Franco

Open Access Theses & Dissertations

Iron (Fe) oxides and hydroxides are common and abundant materials. They exhibit diverse crystal structures, properties and phenomena by virtue of which they find a wide range of scientific and technological applications. Controlled growth and manipulation of the specific structure and electronic behavior to meet the requirements of a given application is a challenging problem in view of many possible phases and composition of the resulting materials. The preparation method and experimental conditions will, therefore, significantly affect the properties and performance of Fe oxides and hydroxides. The goal of the project is to obtain Fe-based oxide/hydroxide catalytic materials and to …

Intermediate Layers In Tandem Organic Solar Cells, Yongbo Yuan, Jinsong Huang, Gang Li

Department of Mechanical and Materials Engineering: Faculty Publications

Tandem structures can boost the efficiency of organic solar cell to more than 15%, compared to the 10% limit of single layer bulk heterojunction devices. Design and fabricating of intermediate layers plays a very important role to achieve high device performance. This article will review the main experimental progresses of tandem organic solar cells, and focus on the intermediate layers (charge recombination layers) in both thermal evaporated and solution processed organic tandem solar cell devices.

A Model Of Giant Vacuole Dynamics In Human Schlemm’S Canal Endothelial Cells, Ryan M. Pedrigi, David Simon, Ashley Reed, W. Daniel Stamer, Darryl R. Overby

Department of Mechanical and Materials Engineering: Faculty Publications

Aqueous humour transport across the inner wall endothelium of Schlemm’s canal likely involves flow through giant vacuoles and pores, but the mechanics of how these structures form and how they influence the regulation of intraocular pressure (IOP) are not well understood. In this study, we developed an in vitro model of giant vacuole formation in human Schlemm’s canal endothelial cells (HSCECs) perfused in the basal-to-apical direction (i.e., the direction that flow crosses the inner wall in vivo) under controlled pressure drops (2 or 6 mmHg). The system was mounted on a confocal microscope for time-lapse en face imaging, and cells …

Freeze-Thawing Of Polyester/E-Glass As An Evaluation Of An Astm International Test Standard Proposal, Stefan Mauritz Strandlund

Electronic Theses and Dissertations

American Composites Manufacturers Association (ACMA) reported in 2009 that the four major sectors currently utilizing fiber reinforced polymers (FRP) are construction, corrosion, marine, and transportation in descending order of total FRP shipped. All of these sectors are known to be billion dollar industries and they are all involved with applications subjected to freezing and thawing. FRP encompass many characteristics that are beneficial to these sectors and also in resisting this exposure. ASTM International has yet not developed a standard to test FRP materials resistance to freeze-thaw (FT) cycling exposure. The D20.18.02 committee of the ASTM is in the process of …

Variable Block Size Motion Compensation In The Redundant Wavelet Domain, Ahmed Abdelgadir Suliman

Dissertations

Video is one of the most powerful forms of multimedia because of the extensive information it delivers. Video sequences are highly correlated both temporally and spatially, a fact which makes the compression of video possible. Modern video systems employ motion estimation and motion compensation (ME/MC) to de-correlate a video sequence temporally. ME/MC forms a prediction of the current frame using the frames which have been already encoded. Consequently, one needs to transmit the corresponding residual image instead of the original frame, as well as a set of motion vectors which describe the scene motion as observed at the encoder. The …

Fundamental Studies Of Co-Base Superalloy Biomedical Prototypes Fabricated By Electron Beam Melting: Microstructures And Microstructural Architecture, Sara M. Gaytan

Open Access Theses & Dissertations

Rapid prototyping, especially electron beam melting (EBM) technology by ARCAM have proven to provide outstanding microstructural and mechanical properties on different alloys fabricated by this technology. Being a computer designed driven technology, complex components, that are hard or even impossible to fabricate by traditional manufacturing techniques, can be fabricated by layer-by-layer EBM technology.

Microstructural and mechanical properties are compared for an EBM femoral knee component prototype with a traditionally-fabricated and body-removed femoral knee implant. Block and cylindrical shape components fabricated by EBM were also analyzed for this project. The alloy utilized for these components is Co-26Cr-6Mo-0.2C characterized by the standards …

Ballistic Projectile Metallurgical Issues And Fundamentals: Aerosol Production In Rod Penetration Erosion And Erosion Phenomena Associated With Railgun Development, Brenda Ivette Machado

Open Access Theses & Dissertations

The issue is derived from ballistic erosion as it relates to nanoparticle production and respiration of these particles as a health concern ballistic erosion and ballistic erosion as it relates to railgun performance. A common thread between these two issues is dynamic recrystallization (DRX). DRX has been demonstrated to be the dominant mechanism for solid-state flow associated with ballistic projectile/target penetration and interaction, friction-stir welding phenomena, and other high-strain rate deformation phenomena.

Aerosol particulates collected on filters from ballistic penetration and erosion events for W-Ni-Co and W-Ni-Fe kinetic energy rod projectiles penetrating steel target plates were observed to be highly …

Microstructural Architecture Developed In The Fabrication Of Solid And Open-Cellular Copper Components By Additive Manufacturing Using Electron Beam Melting, Diana Alejandra Ramirez

Open Access Theses & Dissertations

The fabrication of Cu components were first built by additive manufacturing using electron beam melting (EBM) from low-purity, atomized Cu powder containing a high density of Cu2O precipitates leading to a novel example of precipitate-dislocation architecture. These microstructures exhibit cell-like arrays (1-3µm) in the horizontal reference plane perpendicular to the build direction with columnar-like arrays extending from ~12 to >60 µm in length and corresponding spatial dimensions of 1-3 µm. These observations were observed by the use of optical metallography, and scanning and transmission electron microscopy. The hardness measurements were taken both on the atomized powder and the Cu components. …