Engineering Science and Materials Commons^™

Design And Development Of Ultrabroadband, High-Gain, And High-Isolation Thz Mimo Antenna With A Complementary Split-Ring Resonator Metamaterial, Ammar Armghan, Khaled Aliqab, Meshari Alsharari, Osamah Alsalman, Juveriya Parmar, Shobhit K. Patel

Department of Mechanical and Materials Engineering: Faculty Publications

The need for high-speed communication has created a way to design THz antennas that operate at high frequencies, speeds, and data rates. In this manuscript, a THz MIMO antenna is designed using a metamaterial. The two-port antenna design proposed uses a complementary splitring resonator patch. The design results are also compared with a simple patch antenna to show the improvement. The design shows a better isolation of 50 dB. A broadband width of 8.3 THz is achieved using this complementary split-ring resonator design. The percentage bandwidth is 90%, showing an ultrabroadband response. The highest gain of 10.34 dB is achieved …

An Aptamer-Based Microelectrode With Tunable Linear Range For Monitoring Of K+ In The Living Mouse Brain, Yuan-Dong Liu, Jia-Run Li, Li-Min Zhang, Yang Tian

Journal of Electrochemistry

Potassium ion (K⁺) is widely involved in several physiopathological processes, and its abnormal changes are closely related to the occurrence of brain diseases of cerebral ischemia. In vivo acquirement of K⁺ variation is significant to understand the roles of K⁺ playing in brain functions. A microelectrode based on single-stranded DNA aptamers was developed for highly selective detection of K⁺ in brain, in which the aptamer probes were designed to contain an aptamer part for specific recognition of K⁺, an alkynyl group used for stable confinement of aptamer probe on the gold surface, and …

Scanning Photoelectrochemical Microscopic Study In Photoinduced Electron Transfer Of Supramolecular Sensitizers-Tio2 Thin Films Systems, Sheng-Ya Zhang, Min Yao, Ze Wang, Tian-Jiao Liu, Rong-Fang Zhan, Hui-Qin Ye, Yan-Jun Feng, Xiao-Quan Lu

Journal of Electrochemistry

Crafting charge transfer channels at titanium dioxide (TiO₂) based photoanodes remain a pressing bottleneck in solar-to-chemical conversion technology. Despite the tremendous attempts, TiO₂ as the promising photoanode material still suffers from sluggish charge transport kinetics. Herein, we propose an assembly strategy that involves the axial coordination grafting metalloporphyrin-based photosensitizer molecules (MP) onto the surface-modified TiO₂ nanorods (NRs) photoanode, forming the composite MP/TiO₂ NRs photoelectrode. As expected, the resulted unique MP_B/TiO₂ NRs photoelectrode displays significantly improved photocurrent density as compared to TiO₂ NRs alone and MP_A/TiO₂ NRs photoelectrode. Scanning …

Restoration Of Normal Blood Flow In Atherosclerotic Arteries Promotes Plaque Stabilization, Morgan A. Schake, Ian Mccue, Evan T. Curtis, Thomas J. Ripperda Jr., Samuel Harvey, Bryan T. Hackfort, Anna Fitzwater, Yiannis S. Chatzizisis, Forrest Kievit, Ryan M. Pedrigi

Department of Mechanical and Materials Engineering: Faculty Publications

Blood flow is a key regulator of atherosclerosis. Disturbed blood flow promotes atherosclerotic plaque development, whereas normal blood flow protects against plaque development. We hypothesized that normal blood flow is also therapeutic, if it were able to be restored within atherosclerotic arteries. Apolipoprotein E-deficient (ApoE^-/-) mice were initially instrumented with a blood flow-modifying cuff to induce plaque development and then five weeks later the cuffwas removed to allowrestoration of normal blood flow. Plaques in decuffed mice exhibited compositional changes that indicated increased stability compared to plaques in mice with the cuff maintained. The therapeutic benefit of decuffingwas comparable …

Recent Developments In Timber Design & Its Impact On Carbon Emissions, Raquel Jackson

Spectra Undergraduate Research Journal

This paper explores recent developments in timber building designs and its potential towards reducing carbon emissions. Carbon dioxide emissions are a growing issue worldwide as urbanization and industrialization continues to increase. The rising concentration of carbon dioxide emissions pose significant concerns towards public welfare and environmental health. Despite current methods to reduce greenhouse gasses, carbon emissions remain difficult to reduce from steel and concrete industries. Increasing timber use in building design is a possible solution. Increasing more timber in building design can help reduce carbon emissions due to the carbon-absorbing properties of the construction material. Timber as a construction material …

Comparative Cutting Fluid Study On Optimum Grinding Parameters Of Ti-6al-4v Alloy Using Flood, Minimum Quantity Lubrication (Mql), And Nanofluid Mql (Nmql), Jaime Taha-Tijerina, Immanuel A. Edinbarough

Informatics and Engineering Systems Faculty Publications

Titanium alloys have been of paramount interest to the aerospace industry due to their attractive characteristics. However, these alloys are difficult to machine and require grinding post-processes for quality assurance of the products. Conventional grinding takes a long time and uses a flood coolant-lubrication technique, which is not cost effective nor environmentally friendly. Several studies have been performed to prove the viability and benefit of using Minimum Quantity Lubrication (MQL) with vegetable or synthetic-ester fluids. This work aims to find the optimum grinding parameters of creep feed grinding Ti-6Al-4V with a green silicon carbide wheel, using a flood lubrication system …

Morphology And Hemodynamics Of Cerebral Arteries And Aneurysms In A Rare Pair Of Monozygotic Twins, Hang Yi, Zifeng Yang, Luke C. Bramlage, Bryan R. Ludwig

Mechanical and Materials Engineering Faculty Publications

In this preliminary study, the underlying pathophysiology mechanisms of cerebral aneurysms (CAs) in monozygotic twins (MTs) were investigated via a rare pair of MTs (twin A and twin B) involving four reconstructed arterial models using preclinical information. First, dimensions and configurated outlines of three-perspective geometries were compared. Adopting an in-vitro validated numerical CA model, hemodynamic characteristics were investigated in the MTs, respectively. Despite expected genetic similarities, morphological comparisons show that configurations of cerebral arteries exhibit significant differences between the twins. The ICA size of twin A is larger than that in twin B (2.23~25.86%), varying with specific locations, attributing to …

The Center For Centering Dome, Olek Piechaczek, Ryan M. Scharf

Architectural Engineering

The Center for Centering seeks to create a large-scale healing center, conducive to individual centering of the mind and body. This mobile installation provides a relaxing, enclosed space while still maintaining a connection to the outdoors. The clients liked the idea of having a pop-up installation that could be easily set up as a touring display. With a deadline for installation looming in June 2022, a team of students had five months to design and manufacture the structure.

In winter 2022, the students developed custom geometry to minimize the number of individual parts and built a ¼ scale model of …

Fe Nanoparticles Encapsulated In N-Doped Porous Carbon For Efficient Oxygen Reduction In Alkaline Media, Chun-Yan Li, Rui Zhang, Xiao-Jie Ba, Xiao-Le Jiang, Yao-Yue Yang

Journal of Electrochemistry

Rational design and synthesis of non-precious-metal catalyst plays an important role in improving the activity and stability for oxygen reduction reaction (ORR) but remains a major challenge. In this work, we used a facile approach to synthesize iron nanoparticles encapsulated in nitrogen-doped porous carbon materials (Fe@N-C) from functionalized metal-organic frameworks (MOFs, MET-6). Embedding Fe nanoparticles into the carbon skeleton increases the graphitization degree and the proportion of graphitic N as well as promotes the formation of mesopores in the catalyst. The Fe@N-C-30 catalyst showed the excellent ORR activity in alkaline solutions (E₀ = 0.97 V vs. RHE, E_{1/2 …}

P-Doped Ru-Pt Alloy Catalyst Toward High Performance Alkaline Hydrogen Evolution Reaction, Rong-Qin Huang, Wei-Ping Liao, Meng-Xuan Yan, Shi Liu, Yuan-Ming Li, Xiong-Wu Kang

Journal of Electrochemistry

Electrocatalytic water splitting represents grand promise for hydrogen fuel in modern energy equipment, and the design and fabrication of higher performance catalysts are at the central. Herein, we report the sequential phosphorus (P)-doping into ruthenium (Ru) nanoparticles (Ru-P/C) by thermal annealing of Ru nanoparticles in phosphine (PH₃) atmosphere and deposition of extremely low concentration of platinum (Pt) to obtain P-doped Ru-Pt alloy catalyst supported on carbon nanotubes (CNTs), which is denoted as (Ru-P)#Pt/C. The data by X-ray diffraction spectroscopy and transmission electron microscopy show that the Ru nanoparticles existed in the form of hexagonal close-packed (hcp) phase with …

Deep Euteceic Solvents-Assisted Synthesis Of Novel Network Nanostructures For Accelerating Formic Acid Electrooxidation, Jun-Ming Zhang, Xiao-Jie Zhang, Yao Chen, Ying-Jian Fan, You-Jun Fan, Jian-Feng Jia

Journal of Electrochemistry

Deep eutectic solvents (DESs) have been reported as a type of solvent for the controllable synthesis of metal nanostructures. Interestingly, flower-like palladium (Pd) nanoparticles composed of staggered nanosheets and nanospheres are spontaneously transformed into three-dimensional (3D) network nanostructures in choline chloride-urea DESs using ascorbic acid as a reducing agent. Systematic studies have been carried out to explore the formation mechanism, in which DESs itself acts as a solvent and soft template for the formation of 3D flower-like network nanostructures (FNNs). The amounts of hexadecyl trimethyl ammonium bromide and sodium hydroxide also play a crucial role in the anisotropic growth and …

Exploring The Intersection Of Biology And Design For Product Innovations, Ajay P. Malshe, Salil Bapat, Kamlakar Rajurkar, Ang Ang, Jean-Marc Linares

Department of Mechanical and Materials Engineering: Faculty Publications

Design, development, productization, and applications of advanced product concepts are pressing for higher multifunctionality, resilience, and maximization of available resources equitably to meet the growing and continuing demands of global customers. These demands have further accelerated during the recent COVID- 19 pandemic and are continuing to be a challenge. Engineering designs are one of the most effective ways to endow products with functions, resilience, and sustainability. Biology, through millions of years of evolution, has met these acute requirements under severe resource and environmental constraints. As the manufacturing of products is reaching the fundamental limits of raw materials, labor, and resource …

Pour-Over Coffee Stand With Warmer, Francesca Patawaran

Honors Theses

This project sought to demonstrate the process of bringing a new product into the market, from the initial design and prototyping stage to marketing and, ultimately, mass production. As part of the curriculum of The Haley Barbour Center for Manufacturing Excellence (CME), the project team manufactured fifteen Pour-Over Coffee Stands with electric heating components. We first created a 3D model of the proposed design, ensuring that all components fit together in an assembly. Next, we worked with the lab technicians to create a prototype of the product. Then, we refined the manufacturing process to eliminate waste where possible. Throughout the …

Integrating Steel Slag Aggregates Into Asphalt Paving By Harmonizing Availability, Quality, Economics, And The Environment, Timothy R. Murphy

Theses and Dissertations

This thesis provides guidance on how to balance matters related to the environmental stewardship, market sources, origin and uses, material properties, performance, and economic impact of using slag materials in pavements. The literature on this topic provides numerous references on the use of slag materials for specific applications, and this thesis aims to make use of those references along with other data from the author to describe slag materials from a holistic perspective and provide some suggestions for balancing several factors that impact optimal use of this resource within pavement structures. Discussion is given to the increased importance of recycling …

Soil Respiration Measurements Reveal High Retention Of Organic Carbon From Corn Residue Derived High-Lignin Fermentation Byproduct Enabling Sustainable Lignocellulosic Biofuel Production, Michelle Sun Wang

Dartmouth College Master’s Theses

While 2G biofuel production can utilize non-edible, lignocellulosic feedstocks such as agricultural residues to produce liquid fuel, harvesting crop residues is unsustainable without careful management of the soil underneath. By harvesting a fraction of the crop residues left in the field after harvest, soil health can diminish and critically, the soil organic carbon (SOC) stored in agricultural fields can decrease. Currently, in the most popular 2G process models published, the issue of soil degradation remains unresolved with residue harvest strategies receiving considerable attention in the literature and other SOC management strategies receiving far less. Specifically, the strategy of returning the …

Self-Assembly Of Exfoliated Graphene Flakes As Anticorrosive Coatings For Additive Manufactured Steels, Kaleb Hood, Wen Qian, Yi Xia, Savannah Krupa, Annie Dao, Sarah Ahmed, Samuel Olson, Nam Nguyen, Joseph A. Turner, Jun Jiao

Department of Mechanical and Materials Engineering: Faculty Publications

This study demonstrates the feasibility of using liquid exfoliation of expandable graphite into multilayer exfoliated graphene flakes (EGFs) to form a self-assembled thin film on an air–water interface. The film can coat the surface of additive manufactured (AM) steel substrates to enhance surface properties, specifically AM 316 stainless-steel (AM316), AM 8620 steel (AM8620), and samples of the same alloys made by conventional manufacturing (CM) processes. Liquid exfoliation offers a high yield route for an EGF coating that can cover up to 95% of the sample surface with a single application. The thin, flexible EGFs can coat a rough AM metal …

Exploring Methods For Recycling Filament Waste In 3d Printing, Max Rios Carballo

Publications and Research

The goal of the current study is to investigate cutting-edge techniques for recycling filament waste from 3D printing procedures. Appropriate waste management techniques are required to reduce this trash's harmful environmental consequences. The goal of the project is to look at new methods for recycling filament waste in order to minimize disposal and encourage reuse. To acquire data from pertinent papers and research, a thorough literature review methodology was used. The findings show that this issue may be resolved utilizing a variety of recycling techniques, including shredding, melting, and re-extrusion. The type of filament waste and the intended goal will …

Machinability Of High Mn Steel Using Tool Life Criteria, Dika Handayani, Victor F. Okhuysen, Nicole Wagner

Engineering Faculty Articles and Research

High Mn steel alloys have shown to provide both high strength and ductility. However, current literature offers limited guidance on the machinability of these steel alloys. Therefore, this work provides turning recommendations for high Mn steel that is based on tool life data. Several indexable carbide inserts with various rake angles were used to machine cast billets of high Mn steel. Turning characteristics from various feed rates, cutting speeds, and depths of cut were analyzed. Through a design of experiments, it was determined that the feed rate was the most significant factor affecting tool life and that a tool with …

Enhancing Compatibility And Mechanical Properties Of Natural Rubber Composites, Krisma Yessi Sianturi, Adam Febriyanto Nugraha, Belle Kristaura, Mochamad Chalid

Journal of Materials Exploration and Findings

Pure natural rubber (NR) exhibits low mechanical properties, necessitating the incorporation of additives like vulcanizing agents and fillers. Carbon black and silica, conventional fillers, are relatively expensive and not environmentally friendly. This study explores using Oil Palm Empty Fruit Bunch (OPEFB) fiber as an affordable, abundant, and biodegradable alternative filler for NR. However, compatibility issues arise between the nonpolar NR and the polar OPEFB fiber. A latex-starch hybrid coupling agent (CA (NR-St)) was added to the composite formulation to address this. NR, OPEFB fiber, and the coupling agent were mixed using an open roll mill with a 10 phr OPEFB …

Mesoscale Modeling And Machine Learning Studies Of Grain Boundary Segregation In Metallic Alloys, Malek Alkayyali

All Dissertations

Nearly all structural and functional materials are polycrystalline alloys; they are composed of differently oriented crystalline grains that are joined at internal interfaces termed grain boundaries (GBs). It is well accepted that GB dynamics play a critical role in many phenomena during materials processing or under operating environments. Of particular interest are GB migration and grain growth processes, as they influence many crystal-size dependent properties, such as mechanical strength and electrical conductivity.

In metallic alloys, GBs offer a plethora of preferential atomic sites for alloying elements to occupy. Indeed, recent experimental studies employing in-situ microscopy revealed strong GB solute segregation …

Characterization Of Novel Self-Healing Polymer Blends For Additive Manufacturing, Truman James Word

Open Access Theses & Dissertations

This dissertation begins with an overview of novel polymer systems which have been developed by the Polymer Extrusion Lab at the University of Texas at El Paso. Many composite polymer systems have been created using many different polymers as well as ceramics and metals primarily in the form of powders added to the bulk polymer. The bulk of this work entails a study that was conducted to develop and characterize the mechanical, shape memory and self-healing properties of three polymer blends: polylactic acid (PLA) combined with maleated styrene-ethylene-butylene-styrene (SEBS-g-MA), acrylonitrile butadiene styrene (ABS) combined with maleated styrene-ethylene-butylene-styrene (SEBS-g-MA), and polylactic …

Assessment Of Bridge Pier Response To Fire, Vehicle Impact, And Air Blast, Chen Fang, Qusai Alomari, Daniel G. Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Highway bridges exposed to intentional or unintentional fire followed by combined vehicle impact and air blast are at risk of significant damage and, possibly, collapse. Limited studies examining the complex effects of these extreme demands on bridge support elements and parametrizing their response and damage are found in the open literature. Research that is presented is part of an ongoing numerical investigation examining round, multi-column, reinforced concrete (RC), bridge pier behavior subject to multi-hazard scenarios involving fire, vehicle impact, and air blast. Detailed nonlinear finite element analysis models of single columns and multi-column piers supported by a pile foundation system …

High-Yield Bioinspired Atmospheric Water Capture Through Hydrogels, Yiwei Gao

UNLV Theses, Dissertations, Professional Papers, and Capstones

Water scarcity is a global issue affecting billions of people, and atmospheric water harvesting (AWH) technology has been identified as a potential solution. However, existing single-material AWH approaches have limited water harvesting yields due to alternated water capture, storage, and release stages, and only function within a high relative humidity range. In my doctoral research project, we developed a bio-inspired, hydrogel-based multi-layer AWH approach that allows for segregated capture, storage, and release stages, and is envisioned to have higher daily water harvesting efficiency even in low-humidity areas. My research began with understanding the relations between hydrogel mechanical stiffness, hydraulic permeability, …

Spectroscopic Studies On Silicon And Chalcopyrite Materials For Solar Energy Applications, Amandee Hua

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this dissertation, silicon-based materials for photovoltaics and chalcopyrite-based materials for photoelectrochemical water splitting are investigated using various spectroscopic and microscopic techniques. Although silicon dominates the photovoltaic market, further improvement can be made by using an alternative low temperature passivation approach. Currently, thermally grown SiO2 passivation is commonly used for silicon solar cells. However, this technique requires high processing temperatures (>800 °C), which increases the thermal budget, potentially decreases the bulk quality of Si, and can lead to difficulties in implementing in production lines. Here, a S-based passivation approach is studied that require lower processing temperatures of ~550 °C. …

Machine Learning-Based Data And Model Driven Bayesian Uncertanity Quantification Of Inverse Problems For Suspended Non-Structural System, Zhiyuan Qin

All Dissertations

Inverse problems involve extracting the internal structure of a physical system from noisy measurement data. In many fields, the Bayesian inference is used to address the ill-conditioned nature of the inverse problem by incorporating prior information through an initial distribution. In the nonparametric Bayesian framework, surrogate models such as Gaussian Processes or Deep Neural Networks are used as flexible and effective probabilistic modeling tools to overcome the high-dimensional curse and reduce computational costs. In practical systems and computer models, uncertainties can be addressed through parameter calibration, sensitivity analysis, and uncertainty quantification, leading to improved reliability and robustness of decision and …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Thermal Behavior Of Plain And Fiber-Reinforced Rigid Concrete Airfield Runways, Arash Karimi Pour

Open Access Theses & Dissertations

The environmental condition and temperature gradient are important factors resulting in concrete airfield runways cracking during the time. Rigid concrete airfield runways experience different thermal gradients during the day and night due to changes in air temperature. Curling and thermal expansion stresses are the main consequences resulting in various types of cracking over the surface and thickness of concrete airfield runways and increasing maintenance costs. The curvature of concrete slabs increases with an increase in the temperature gradient which is amplified when runways open to traffic. Additionally, the combination of the curling and shrinkage stresses, in rare circumstances, can be …

Metastability And Degradation In Cu(In,Ga)Se2 Thin-Film Solar Cells, Mohsen Jahandardoost

UNLV Theses, Dissertations, Professional Papers, and Capstones

Cu(In,Ga)(S,Se)2 or CIGS is a thin-film semiconductor that has shown a device efficiency of 23.35% and 24.2% for single-junction and perovskite/CIGS tandem solar cells, respectively. CIGS offers promising properties such as tunable bandgap and ease of processing making them great candidates for thin-film tandem devices. However, knowledge of the effect of material defects, buffer materials, and post-deposition treatment (PDT) on degradation and metastability behavior in these devices is not well understood.In this dissertation, metastability and long-term degradation of CIGS thin-film solar cells have been investigated under combinatorial stress factors of heat, light, and voltage bias to systematically understand the effect …

Me-Em Enewsbrief, March 2023, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …