Engineering Science and Materials Commons^™

Development, Experimental Validation, And Progressive Failure Modeling Of An Ultra-Thin High Stiffness Deployable Composite Boom For In-Space Applications, Jimesh D. Bhagatji

Mechanical & Aerospace Engineering Theses & Dissertations

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This research focuses on fabrication, experimental testing, and progressive failure modelling to study the deformation of an ultra-thin composite beam. The research study examines deformation modes of a boom under repetitive pure bending loads using 4-point bending setup. The material and …

Multiscale Modeling And Gaussian Process Regression For Applications In Composite Materials, Joshua Arp

All Dissertations

An ongoing challenge in advanced materials design is the development of accurate multiscale models that consider uncertainty while establishing a link between knowledge or information about constituent materials to overall composite properties. Successful models can accurately predict composite properties, reducing the high financial and labor costs associated with experimental determination and accelerating material innovation. Whereas early pioneers in micromechanics developed simplistic theoretical models to map these relationships, modern advances in computer technology have enabled detailed simulators capable of accurately predicting complex and multiscale phenomena.

This work advances domain knowledge via two means: firstly, through the development of high-fidelity, physics-based finite …

Double Cantilever Beam Mode-I Testing Validation In Large-Scale Additive Manufacturing Carbon Composite, Luis Alfonso Camacho

Open Access Theses & Dissertations

Testing for mechanical properties for additive manufacturing has been based on already existing standards for traditional manufacturing methods. For composites in large scale additive manufacturing there is a research gap in bond strength and fracture toughness for a single layer interface. By using Double cantilever beam Mode I, this thesis manuscript validates testing parameters and protocols to describe the intricacies of ABS matrix 20 wt.% carbon filled composite, specifically on the layer-to-layer interface. Studies suggest that fracture toughness is sensitive to process parameters, like deflection speed and sharpened crack tip at the layer interface of BAAM 3D printed part and …

Electrochemical Approaches To Life-Support Resources In Space Missions And Nuclear Technologies: Hydrogen Peroxide And Uranium Films, Armando Manuel Pena-Duarte

Open Access Theses & Dissertations

Space race has developed several technological advances that have achieved and continue to achieve the success of space missions in the aerospace timeline. Currently, the number of space technical and scientific innovations is still growing––demanding new materials and developments for extreme performing applications of fuel cells, batteries, supercapacitors, and systems of nuclear energy. Space missions require life-support solutions, auto-sustainable closed-loop living environments, cleaning and sanitizing solutions against pathogens, and safe nuclear-based resources of energy––with fissile materials with well-controlled dimensions within the core fuel elements. Likewise, to guarantee safety conditions, reduce costs, and facilitate operational logistics, space missions must reduce their …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

Theoretical And Experimental Study Of Active Magnetic Bearing Control Integrated On Bently's Rotor Kit, Arturo Mario Flores

Master's Theses

This thesis focuses on the comprehensive study of controlling a customized Active Magnetic Bearing (AMB) installed on Bently Nevada’s RK4 rotor kit in Cal Poly’s Vibrations and Rotordynamics Lab. The AMB was uniquely designed and manufactured by a Cal Poly senior project team to fit Bently’s rotor kit and the results of this research are distinctive to the custom system. To achieve practical functionality of the AMB system, we designed a controller a Virtual Instrument (VI) using the National Instrument software, LabVIEW. From the experimental study, we calibrated the programming to find unknown parameters of the AMB system and validated …

Development And Characterization Of Lead & Lead-Free Perovskite Solar Cell Materials, Rubaiya Murshed

UNLV Theses, Dissertations, Professional Papers, and Capstones

In recent years, perovskite photovoltaic technology has offered enormous viability and dimensionality in solar cell research. As a light-harvesting active layer, Perovskite generated remarkable development in device efficiency of 25.7% for the single-junction solar cell, and over 33% for the perovskite/silicon tandem solar cell. Also, perovskite-perovskite tandem solar cell (also called all-perovskite tandem solar cell) shows great potential in device performance and achieved a power conversion efficiency (PCE) of 26.4%. Transitioning photovoltaic technology from the laboratory to commercial products, high PCE, low cost, long lifetime, and low toxicity are some of the critical factors to consider during material selection. Pb-halide …

Mechanical Properties Of Biocomposite With Various Composition Of Caco3 And Starch, Agris Setiawan, Fransisca Diana Wahyuningsih, Riria Zendy Mirahati

Journal of Mechanical Engineering Science and Technology (JMEST)

Calcium carbonate has the potential to be used in the development of medical materials, including biomaterials. Biocomposite is composed of CaCO3 as matrix material and bioplastic from the combination of corn starch and cassava starch as reinforcement. This study aims to determine mechanical properties such as tensile strength and bending/flexural strength with varying compositions of CaCO3 and bioplastic. Characterization of the biocomposite uses Scanning Electron Microscope to observe the microstructure and composition elements of their structure. This study used 4 variations in the ratio of CaCO3 suspension: (Corn Starch + Cassava Starch). Each sample was characterized using specimen code A …

Synthesis And Characterization Of Nitrogen-Doped Activated Carbon For Lithium Battery Anode Applications, Prihanto Trihutomo, Poppy Puspitasari, Muhammad Bustomi Radja, Milzam Rahmat Busono

Journal of Mechanical Engineering Science and Technology (JMEST)

Nitrogen-dopped activated carbon was synthesized to see its effect on the characterization of the nitrogen surface functional groups, crystal size, and morphology of the resulting sample. Synthesis of nitrogen-doped activated carbon was carried out by varying the addition of Urea as a nitrogen doping source. Activated carbon compared its characteristics with variations in the concentration of added Urea to activated carbon, at 1:3 and 1:5. The FTIR results obtained were the presence of functional groups indicating the presence of nitrogen bonds in each sample. The crystallinity results showed that the samples were classified as crystalline and nitrogen doping influenced the …

Designing A Naabsa Class Tanker Ship With Bottom Protection From Ground, Victor A. Kulesh, Mathias B. Prasetio, Fam Chung Hiep

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is the world's largest archipelago country with a high potential for economic development and top producer and exporter of palm oil. As an archipelago country, the most efficient cargo transportation routes are through rivers and seas. Designing and building tankers, taking into account the specifics of the operation, are relevant. The paper considers the issues of designing a tanker for the transportation of crude palm oil with a defined operation area and route. The general concept of the vessel is proposed, taking into account the restrictions on the navigation area and draft for operation in the river. Particular attention …

Effect Of Grafting Nano-Tio2 On Sansevieria Cylindrica Fiber Properties, Chrisrulita Sekaradi Wiguna, Heru Suryanto, Aminuddin Aminuddin, Jibril Maulana, Joseph Selvi Binoj, Alamry Ali

Journal of Mechanical Engineering Science and Technology (JMEST)

Natural fibers, which are abundant, environmentally friendly, and biodegradable, are used as a replacement for synthetic fibers. The composite strength can be increased by treating the surfaces of natural fibers with suitable chemicals, which can also improve the interface interaction between fiber and matrix. Application of a coupling agent in chemical treatment is utilized to reinforce the bonding between fiber and matrix. The objective of the study is to determine the influence of silane concentration on the Sansevieria cylindrica fiber properties. The methods included fibers treatment using ethanol and coupling agent as dissolving and TiO2 with concentrations of 0%, 0.25%, …

The Combustion Characteristics Of Calophyllum Inophyllum Fuel In The Presence Of Magnetic Field, Imam Rudi Sugara, Nasrul Ilminnafik, Salahuddin Junus, Muh Nurkoyim Kustanto, Yuni Hermawan

Journal of Mechanical Engineering Science and Technology (JMEST)

The study objective is to investigate the combustion characteristics of Callophyllum inophyllum fuel in presence of a magnetic fields. To conduct the experiment, a bunsen burner was utilized, with fuel and air being dispensed via a syringe pump and compressor, both regulated by a flowmeter. The fuel and air pipes were heated to 532.15 (K) to facilitate fuel evaporation. The equivalent ratio of 0.5, 1, and 1.5 was adjusted to control air discharge and fuel. An 11,000 gausses artificial magnet was used, with N-S, N-S, N-N, and SS being the various magnetic pole configurations. The study found that the magnetic …

Effect Of Current And Pulse-On Time On Material Removal Rate And Surface Roughness Of Tungsten Carbide In Electric Discharge Machine Die-Sinking, Mochamad Deny Riyanto, Andoko Andoko, Heru Suryanto

Journal of Mechanical Engineering Science and Technology (JMEST)

The focus of manufacturing for tungsten carbide applications often demands a smooth surface quality as the result of the Electric Discharge Machine (EDM) die-sinking process, especially in the manufacture of die and mold with tungsten carbide material processed using a die-sinking EDM machine. The purpose of this study is to analyze the effect of electric current and pulse-on time on the Material Removal Rate (MRR) and surface roughness of tungsten carbide. Through the experimental method, the parameters varied, namely electric current 17 A, 20 A, 23 A, and pulse-on time 30 µs, 55 µs, and 80 µs. MRR was calculated …

Lap Joint On St.37 Steel Plate With Friction Welding Clamping Method, Widia Setiawan, Nugroho Santoso, Wiyadi Wiyadi, Muhammad Sulistiyo Aji, Rachmat Alamin, Achsan Tarmudi

Journal of Mechanical Engineering Science and Technology (JMEST)

Friction stir (FW) welding is a relatively fresh method that was created and has been continually refined and adapted to industrial applications due to its benefits. This approach for solid-state joining entails connecting the components at a temperature below their melting point and then heating them up. Clamp joint applications are widely used using external heating and hitting with high strength, but the clamped joints with the FW method are rarely done. The research studied the characteristic of clamped joints at various plate thicknesses using the FW method. In this study, 30 specimens were used in the form of a …

The Effect Of Cutting Speed Of Nitrogen Laser Cutting On The Surface Texture Of Sus 304 Plate, Yanuar Rohmat Aji Pradana, Raka Afrianto, Chandra Hairat Abdul Rahman, Andoko Andoko

Journal of Mechanical Engineering Science and Technology (JMEST)

The focus of today’s machining industry is on how to maintain high productivity and low cost achieved by high tool life during the operation. Laser cutting is considered the right solution because it offers cutting speeds of up to 170000 mm/min through a non-contact process regardless of the workpiece material hardness. The aim of this study is to analyze the effect of cutting speed on the surface texture aspects namely surface roughness, kerf shape, and dross height on the stainless steel 304 plate after laser cutting. The nitrogen laser was utilized with the cutting speed of 400, 1700, and 2000 …

Analysis Of Fire And Smoke Spread In Ki Hajar Dewantara Auditorium, State University Of Jakarta, Using Fire Dynamics Simulator, Pratomo Setyadi, Ariq Harits Arrizq

Journal of Mechanical Engineering Science and Technology (JMEST)

Fire behavior and smoke spread are influenced by various factors, including the amount and condition of combustible material, ventilation openings, and ceiling height. A high amount of combustible material in the auditorium poses a significant fire hazard, hence, efforts need to be made to minimize the risk. One approach is to use Computational Fluid Dynamic software, such as Fire Dynamics Simulator (FDS), to model fire combustion. In this research, it provides an overview of the heat release rate (HRR) of fires that occur as well as the effect of differences in ceiling height and the effect of ventilation on fire …

Effect Of Temperature Variations Of Corn (Maize) Oil Biodiesel On Torque Values And Thermal Efficiency Of Diesel Engines, Suardi Suardi, Rodlian Jamal Ikhwani, Ade Putri Rezki Aulia

Journal of Mechanical Engineering Science and Technology (JMEST)

The trend of consumption of hydrocarbon fuels in Indonesia, which is increasing every year, is not accompanied by the amount of production, which is decreasing. Alternative fuels to reduce dependence on hydrocarbon fuels. One form of alternative fuel is biodiesel, which is made from corn (maize) oil. Corn oil itself, if processed, can be an option for clean and environmentally friendly energy option and that is the main objective of this research is to determine the performance of biodiesel corn oil on diesel engines. The method used in this study is an experimental method where corn oil biodiesel is tested …

Ultramicroelectrode Experiments: Principles, Fabrications And Voltmmetric Behaviors, Zhen Ma, Jia-Yang Lin, Wen-Jing Nan, Lian-Huan Han, Dong-Ping Zhan

Journal of Electrochemistry

Due to the small size at least in one dimension (< 25 μm), ultramicroelectrode (UME) has small electric-double-layer capacitance, low IR drop, rapid mass transfer rate, fast response, high signal/noise ratio and high spatiotenporal resolution. UME is qualified not only to study the kinetics of fast electrode processes, but also to act as the probe of scanning electrochemical microscopies to obtain the localized chemical or electrochemical reactivity of the substrates. Thus, UMEs play a significant role in various research domains of electrochemistry, and have become an important electrochemical experimental method. Herein, we will introduce the basic principles, a simple fabrication method and voltammetric experimental protocols of UME, providing a guide to carry out the UME experiments.

Band Alignments Of Metal/Oxides-Water Interfaces Using Ab Initio Molecular Dynamics, Yong-Bin Zhuang, Jun Cheng

Journal of Electrochemistry

Band alignments of electrode-water interfaces are of crucial importance for understanding electrochemical interfaces. In the scenario of electrocatalysis, applied potentials are equivalent to the Fermi levels of metals in the electrochemical cells; in the scenario of photo(electro)catalysis, semiconducting oxides under illumination have chemical reactivities toward redox reactions if the redox potentials of the reactions straddle the conduction band minimums (CBMs) or valence band maximums (VBMs) of the oxides. Computational band alignments allow us to obtain the Fermi level of metals, as well as the CBM and VBM of semiconducting oxides with respect to reference electrodes. In this tutorial, we describe …

Recent Progress Of Bifunctional Electrocatalysts For Oxygen Electrodes In Unitized Regenerative Fuel Cells, Tian-Long Zheng, Ming-Yu Ou, Song Xu, Xin-Biao Mao, Shi-Yi Wang, Qing-Gang He

Journal of Electrochemistry

Unitized regenerative fuel cells (URFCs), which oxidize hydrogen to water to generate electrical power under thefuel cells (FCs) mode and electrolyze water to hydrogen under the water electrolysis (WE) mode for recycling, areknown as clean and sustainable energy conversion devices. In contrast to the hydrogen oxidation reaction (HOR) andhydrogen evolution reaction (HER) on the hydrogen electrode side, the sluggish kinetics of oxygen reduction reaction(ORR) and oxygen evolution reaction (OER) on the oxygen electrode side requires highly efficient bifunctional oxygencatalysts. Conventional precious metal oxygen catalysts combine Pt and IrO₂ with excellent ORR and OER activities toachieve bifunctional electrocatalysis performance, but …

Electrochemical Scanning Tunneling Microscopy: Taking The Initial Stage Of Cu Electrodeposition On Au(111) As An Example, Zhuo Tan, Kai-Xuan Li, Bing-Wei Mao, Jia-Wei Yan

Journal of Electrochemistry

Electrochemical scanning tunneling microscopy (ECSTM) plays an important role in the field of electrochemistry, which can obtain potential-dependent structural information of electrode surface with high spatial resolution and observe some reaction processes in electrolyte solutions, and provide a powerful way to understand the interfacial structure and electrode processes from the perspective of high spatial resolution. In this article, the study of electrodeposition of Cu on Au (111) by ECSTM is taken as an example to introduce the experimental methods required for ECSTM and share our experience with other electrochemical groups. Firstly, the working principle of STM is introduced so that …

Twin-Solute, Twin-Dislocation And Twin-Twin Interactions In Magnesium, Materials Yue, Jian Wang, Jian-Feng Nie

Department of Mechanical and Materials Engineering: Faculty Publications

Magnesium alloys have received considerable research interest due to their lightweight, high specific strength and excellent castability. However, their plastic deformation is more complicated compared to cubic materials, primarily because their low-symmetry hexagonal closepacked (hcp) crystal structure. Deformation twinning is a crucial plastic deformation mechanism in magnesium, and twins can affect the evolution of microstructure by interacting with other lattice defects, thereby affecting the mechanical properties. This paper provides a review of the interactions between deformation twins and lattice defects, such as solute atoms, dislocations and twins, in magnesium and its alloys. This review starts with interactions between twin boundaries …

Atomistic Simulations Of Twin Facets Associated With Three-Dimensional { []011 } Twins In Magnesium, Qiyu Zeng, Mingyu Gong, Houyu Ma, Yao Shen, Jian-Feng Nie, Jian Wang, Yue Liu

Department of Mechanical and Materials Engineering: Faculty Publications

Twinning is a deformation mechanism that creates three-dimensional (3D) twin domains through the migration of twin facets. This occurs via the nucleation and glide of twinning disconnections (TDs), which can pile up to create twin facets. A comprehensive under- standing of twin facets associated with 3D twins, including their atomic structures and energies, is crucial for understanding deformation twinning. In this study, we propose a molecular statics/dynamics (MS/MD) approach to determine characteristic twin facets enclosing 3D non-equilibrium/equilibrium { [] 011 } twin domains, which has been much less studied than the counterpart { [] 012 } twin domains. The stability …

The Essential Work Of Fracture In Peridynamics, Christer Stenström, Kjell Eriksson, Florin Bobaru, Stefan Golling, Pär Jonsén

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, the essential work of fracture (EWF) method is introduced for a peridynamic (PD) material model to characterize fracture toughness of ductile materials. First, an analytical derivation for the path-independence of the PD J -integral is provided. Thereafter, the classical J -integral and PD J-integral are computed on a number of analytical crack problems, for subsequent investigation on how it performs under large scale yielding of thin sheets. To represent a highly nonlinear elastic behavior, a new adaptive bond stiffness calibration and a modified bonddamage model with gradual softening are proposed. The model is employed for two …

Mesoporous Particle Embedded Nanofibrous Scaffolds Sustain Biological Factors For Tendon Tissue Engineering, Chiara Rinoldi, Ewa KijeńSka-GawrońSka, Marcin Heljak, Jakub Jaroszewicz, Artur KamińSki, Ali Khademhosseini, Ali Tamayol, Wojciech Swieszkowski

Department of Mechanical and Materials Engineering: Faculty Publications

In recent years, fiber-based systems have been explored in the frame of tissue engineering due to their robustness in recapitulating the architecture and mechanical properties of native tissues. Such scaffolds offer anisotropic architecture capable of reproducing the native collagen fibers’ orientation and distribution. Moreover, fibrous constructs might provide a biomimetic environment for cell encapsulation and proliferation as well as influence their orientation and distribution. In this work, we combine two fiber fabrication techniques, such as electrospinning and wet-spinning, in order to obtain novel cell-laden 3D fibrous layered scaffolds which can simultaneously provide: (i) mechanical support; (ii) suitable microenvironment for 3D …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

The Plastics Collection Reference Packet, Special Collections Research Center

Special Collections Research Center

This reference packet is an informational tool to support further research into the history of plastics—whether interested in companies, individuals within the plastics industry's history, historical plastics materials, essays, and more. All content featured within this packet was previously published on the former plastics.syr.edu website as part of a Syracuse University Libraries and Special Collections Research Center (SCRC) partnership established in 2007 with the Plastics Pioneers Association (PPA)—an association of plastics industry professionals interested in preserving the plastics industry's past.

Neurocomputing And Interfacing Digital Tasting System: Research, Design, And Evaluation, Amira J. Zaylaa, Ahmad El Hajj

BAU Journal - Science and Technology

The continuous evolution in computing and interfacing has been extended to develop multi-sensory experiences in many domains such as neurological, auditory, vision, and haptic domains. So far, only a few remarkable system approaches have been approved to be serving the taste sensation digitally. Although taste sensation is linked to the brain, there is a lack of optimal neurocomputing digital taste sensation systems. Our study provides a new neurocomputing method to digitally stimulate the sense of taste by electrical stimulation on the human tongue. We aim to link chemical stimulation and electrical stimulation in order to design an electronic interface for …

Methods And Surface Materials Repair For Concrete Structures – A Review, Lelian W. Elkhatib, Adel Elkordi, Jamal Khatib

BAU Journal - Science and Technology

Concrete is a very critical material that may require maintenance and possible repair periodically, especially in important structure such as bridges. In general, concrete in structures (e.g. reinforced concrete) may be subjected to cracks due to a variety of reasons. These include, design and external environments such as the ingress of harmful ions into the concrete, unexpected extra loads including earthquakes. These cracks can affect not only the appearance of the structure but more importantly the structural performance of concrete and the integrity of the concrete structure. Therefore, when cracks occur a proper repair method should be selected, based on …

Nitric Oxide: Physiological Functions, Delivery, And Biomedical Applications, Syed Muntazir Andrabi, Navatha Shree Sharma, Anik Karan, S. M. Shatil Shahriar, Brent Cordon, Bing Ma, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Nitric oxide (NO) is a gaseous molecule that has a central role in signaling pathways involved in numerous physiological processes (e.g., vasodilation, neurotransmission, inflammation, apoptosis, and tumor growth). Due to its gaseous form, NO has a short half-life, and its physiology role is concentration dependent, often restricting its function to a target site. Providing NO from an external source is beneficial in promoting cellular functions and treatment of different pathological conditions. Hence, the multifaceted role of NO in physiology and pathology has garnered massive interest in developing strategies to deliver exogenous NO for the treatment of various regenerative and biomedical …