Transportation Engineering Commons^™

Long-Term Durability Of Frp Bond In The Midwest United States For Externally-Strengthened Bridge Components, Sasan Siavashi, Christopher D. Eamon, Abdel A. Makkawy, Hwai-Chung Wu

Civil and Environmental Engineering Faculty Research Publications

In this study, the bond strength of a typical FRP system subjected to long-term natural weathering in the Midwest United States is experimentally investigated, and the rate of degradation is estimated. To do this, the bond strength of an FRP system exposed to over fifteen years of weathering is determined with pull-off testing, and a relationship between strength reduction and exposure time is developed using regression analysis. For unweathered specimens, it was found that the attachment strength of the FRP system was governed by the concrete substrate, while for weathered specimens, the FRP system could detach by either a failure …

Webinar: Modeling Freeway Traffic In A Mixed Environment: Connected And Human-Driven Vehicles, Xianfeng Terry Yang

TREC Webinar Series

Although connected vehicles (CVs) will soon go beyond testbeds, CVs and human-driven vehicles (HVs) will co-exist over a long period. Hence, it is critical to consider the interactions between these two types of vehicles in traffic flow modeling. In this study, we aim to develop a macroscopic model to understand how CVs would impact HVs in the traffic stream. Grounded on the second-order traffic flow model, we study the relationships among flow, density, and speed by two sets of formulations for the groups of CVs and HVs, respectively. A set of friction factors, which indicate CVs' impact to HVs, are …

Pedestrian Safety -- Fundamental To A Walkable City, Joshua Herrera, Patrick Mcdevitt, Preeti Swaminathan, Raghuram Srinivas

SMU Data Science Review

In this paper, we present a method to identify urban areas with a higher likelihood of pedestrian safety related events. Pedestrian safety related events are pedestrian-vehicle interactions that result in fatalities, injuries, accidents without injury, or near--misses between pedestrians and vehicles. To develop a solution to this problem of identifying likely event locations, we assemble data, primarily from the City of Cincinnati and Hamilton County, that include safety reports from a five year period, geographic information for these events, citizen survey of pedestrian reported concerns, non-emergency requests for service for any cause in the city, property values and public transportation …

Optimizing In-Place Density Of Asphalt Pavements During Cold Weather Paving In Nebraska, Robert C. Rea, Hamzeh Haghshenas

Nebraska Department of Transportation: Research Reports

Late season paving is common and often performed in colder temperatures, which is the most challenging environment for attaining optimal in-place density/compaction The in-place density of asphalt pavement greatly affects the lifespan of the pavement. It is also a key factor in preventing major pavement distresses, such as rutting, cracking, stripping (due to water damage) and aging. This research project aims to evaluate and compare the effectiveness of different compaction, delivery, and mix design characteristics to ensure the optimization of in-place asphalt pavement density. To this end, various laydown methods (i.e., Standard Pick-up Machine (SPM) and Material Transfer Vehicle (MTV)) …

Sensitivity Of Evacuation Time Estimation To Modeling Parameter Adjustment, Nelida Andreina Herrera

LSU Doctoral Dissertations

Over the past 40 years, a range of tools and techniques have been employed to assess traffic and travel conditions associated with evacuation events. These tools provide key insights into the temporal-spatial conditions of traffic during an evacuation. The representation of an evacuation in a traffic simulation model requires a number of assumptions about the input and modeling parameters needed to capture relevant aspects of such event. Therefore, a key aspect to ensure appropriate estimations of evacuation clearance times and overall efficacy of emergency planning is to better understand the influence and the importance that simulation modeling parameters have on …

Effect Of Different Traffic Signal Control Plans On Simulation Of Hurricane Evacuation Traffic, Divya Kolasani

LSU Master's Theses

The majority of hurricane evacuation modeling studies concentrate on evacuation traffic on freeways with relatively little attention being given to traffic on arterials. This study is focused on evaluating the evacuation efficiency of a network under different traffic signal settings on arterials using microscopic simulation. This is achieved by changing the traffic signal settings from existing signal timing plans to flashing yellow on major evacuation routes and flashing red on cross streets, for a given evacuation order. Time-dependent origin-destination matrices for hurricane evacuation up to 72 hours away from landfall for No Evacuation order, as well as a Voluntary/Mandatory Evacuation …

18-02 Investigating And Prioritizing Factors For Quantifying Bikeability, Valerian Kwigizile, Jun-Seok Oh, Sia M. Lyimo

Transportation Research Center Reports

Bikeability is an important element that must be considered in planning bicycle facilities. The resource constraints make it imperative for the planners and engineers to be able to identify and shortlist important factors that promote cyclists’ friendly environment. The current study utilized the Analytical Hierarchy Process (AHP), a multiple criteria decision analysis technique, to rank the relative importance of bikeability factors for on-road bicycle facilities. AHP is the most applied multiple criteria decision analysis technique due to its ability to convert subjective judgment to a numerical value which can easily be incorporated in the decision-making process. A survey was administered …

Smart Roads: Investigating Roadways As Energy Sources For Potential Application Of In-Lane Charging, Dhruvalkumar Hitendrakumar Patel

Theses, Dissertations and Capstones

The main aim of this thesis is to explore the potential for using pavements as part of energy harvesting infrastructure. Asphalt pavements can be used for multiple purposes such as for energy harvesting, eco-friendly use of the car, and the utilization of the natural renewable resources to produce electricity and that electricity use for in-lane charging technology which helps to charge a car when it is being driven on the road. The wireless charger is set-up under the asphalt pavement, and it will produce the magnetic field. The piezoelectric material and wind turbine are the electric source for applications such …

Fuel Consumption And Emissions Performance Under Real Driving: Comparison Between Hybrid And Conventional Vehicles., Yuhan Huang, Surawski C. Nic, Organ Bruce, John L. Zhou, Oscar H.H Tang, Edward F.C. Chan

Faculty of Science & Technology (THEi)

Hybrid electric vehicles (HEVs) are perceived to be more energy efficient and less polluting than conventional internal combustion engine (ICE) vehicles. However, increasing evidence has shown that real-driving emissions (RDE) could be much higher than laboratory type approval limits and the advantages of HEVs over their conventional ICE counterparts under real-driving conditions have not been studied extensively. Therefore, this study was conducted to evaluate the real-driving fuel consumption and pollutant emissions performance of HEVs against their conventional ICE counterparts. Two pairs of hybrid and conventional gasoline vehicles of the same model were tested simultaneously in a novel convoy mode using …

Characterisation Of Diesel Vehicle Emissions And Determination Of Remote Sensing Cutpoints For Diesel High-Emitters., Yuhan Huang, Organ Bruce, John L. Zhou, Surawski C. Nic, Yat-Shing Yam, Edward F.C. Chan

Faculty of Science & Technology (THEi)

Diesel vehicles are a major source of air pollutants in cities and have caused significant health risks to the public globally. This study used both on-road remote sensing and transient chassis dynamometer to characterise emissions of diesel light goods vehicles. A large sample size of 183 diesel vans were tested on a transient chassis dynamometer to evaluate the emission levels of in-service diesel vehicles and to determine a set of remote sensing cutpoints for diesel high-emitters. The results showed that 79% and 19% of the Euro 4 and Euro 5 diesel vehicles failed the transient cycle test, respectively. Most of …

Ua66/9/1 Ogden College Of Science & Engineering Engineering Administration, Wku Archives

WKU Archives Collection Inventories

No abstract provided.

Improving Traffic Safety At School Zones By Engineering And Operational Countermeasures, Md Hasibur Rahman

Electronic Theses and Dissertations

Safety issues at school zone areas have been one of the most important topics in the traffic safety field. Although many studies have evaluated the effectiveness of various traffic control devices (e.g., sign, flashing beacon, speed monitoring display), there is a lack of studies exploring different roadway countermeasures and the relationship between school-related factors and crashes. In this study, the most crash-prone school zone was identified in Orange and Seminole Counties, Florida, based on crash rate. Afterward, a microsimulation network was built in VISSIM environment to test different roadway countermeasures in the school zones. Three different countermeasures: two-step speed reduction …

Impact Of Potential Engine Malfunctions On Fuel Consumption And Gaseous Emissions Of A Euro Vi Diesel Truck., Yuhan Huang, Elvin C.Y. Ng, Yat-Shing Yam, Casey K.C. Lee, Surawski C. Nic, Wai-Chuen Mok, Organ Bruce, John L. Zhou, Edward F.C. Chan

Faculty of Science & Technology (THEi)

Although new vehicles are designed to comply with specific emission regulations, their in-service performance would not necessarily achieve them due to wear-and-tear and improper maintenance, as well as tampering or failure of engine control and exhaust after-treatment systems. In addition, there is a lack of knowledge on how significantly these potential malfunctions affect vehicle performance. This study was therefore conducted to simulate the effect of various engine malfunctions on the fuel consumption and gaseous emissions of a 16-tonne Euro VI diesel truck using transient chassis dynamometer testing. The simulated malfunctions included those that would commonly occur in the intake, fuel …

Evaluation Of Nebraska’S Aggregate Reactivity By The Miniature Concrete Prism Test Method – Aashto T380, Lieska Halsey, Wally Heyen

Nebraska Department of Transportation: Research Reports

The evaluation of nine different aggregates shows the viability of the T380 test method as an alternative to the standard C1293 test method. The T380 assesses the Alkali-Silica Reaction potential of aggregates with the same reliability as C1293 and correlates well with the C1293 test method. Results are obtained within 56 days by T380 compared to 365 days required by C1293. The T380 method at 56 days appears to characterize the aggregate reactivity similarly to C1293 for all the aggregates evaluated in this study. Therefore, T380 will be part of the Department test method for approval of interground/blended cements along …

Arterial-Level Real-Time Safety Evaluation In The Context Of Proactive Traffic Management, Jinghui Yuan

Electronic Theses and Dissertations

In the context of pro-active traffic management, real-time safety evaluation is one of the most important components. Previous studies on real-time safety analysis mainly focused on freeways, seldom on arterials. With the advancement of sensing technologies and smart city initiative, more and more real-time traffic data sources are available on arterials, which enables us to evaluate the real-time crash risk on arterials. However, there exist substantial differences between arterials and freeways in terms of traffic flow characteristics, data availability, and even crash mechanism. Therefore, this study aims to deeply evaluate the real-time crash risk on arterials from multiple aspects by …

Assessing Pedestrian Safety Conditions On Campus, Morgan Morris

Electronic Theses and Dissertations

Pedestrian-related crashes are a significant safety issue in the United States and cause considerable amounts of deaths and economic cost. Pedestrian safety is an issue that must be uniquely evaluated in a college campus, where pedestrian volumes are dense. The objective of this research is to identify issues at specific locations around UCF and suggest solutions for improvement. To address this problem, a survey that identifies pedestrian safety issues and locations is distributed to UCF students and staff, and an evaluation of drivers reactions to pedestrian to vehicle (P2V) warning systems is studied through the use of a NADS MiniSim …

Assessing The Safety And Operational Benefits Of Connected And Automated Vehicles: Application On Different Roadways, Weather, And Traffic Conditions, Md Sharikur Rahman

Electronic Theses and Dissertations

Connected and automated vehicle (CAV) technologies have recently drawn an increasing attention from governments, vehicle manufacturers, and researchers. Connected vehicle (CV) technologies provide real-time information about the surrounding traffic condition (i.e., position, speed, acceleration) and the traffic management center's decisions. The CV technologies improve the safety by increasing driver situational awareness and reducing crashes through vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I). Vehicle platooning with CV technologies is another key element of the future transportation systems which helps to simultaneously enhance traffic operations and safety. CV technologies can also further increase the efficiency and reliability of automated vehicles (AV) by collecting real-time …

The Use Of 3-D Highway Differential Geometry In Crash Prediction Modeling, Kiriakos Amiridis

Theses and Dissertations--Civil Engineering

The objective of this research is to evaluate and introduce a new methodology regarding rural highway safety. Current practices rely on crash prediction models that utilize specific explanatory variables, whereas the depository of knowledge for past research is the Highway Safety Manual (HSM). Most of the prediction models in the HSM identify the effect of individual geometric elements on crash occurrence and consider their combination in a multiplicative manner, where each effect is multiplied with others to determine their combined influence. The concepts of 3-dimesnional (3-D) representation of the roadway surface have also been explored in the past aiming to …

Quantifying The Impact Of Transportation Network Companies (Tncs) On Traffic Congestion In San Francisco, Sneha Roy

Theses and Dissertations--Civil Engineering

This research investigates whether Transportation Network Companies (TNCs), such as Uber and Lyft, live up to their stated vision of reducing congestion by complementing transit and reducing car ownership in major cities. The objective of this research study is to answer the question: are TNCs are correlated to traffic congestion in the city of San Francisco? If found to be so, do they increase or decrease traffic congestion for the case of San Francisco? If and how TNC pickups and drop-offs impact traffic congestion within San Francisco? And finally, how does the magnitude of this measured command of TNCs on …

Evaluate Probe Speed Data Quality To Improve Transportation Modeling, Fahmida Rahman

Theses and Dissertations--Civil Engineering

Probe speed data are widely used to calculate performance measures for quantifying state-wide traffic conditions. Estimation of the accurate performance measures requires adequate speed data observations. However, probe vehicles reporting the speed data may not be available all the time on each road segment. Agencies need to develop a good understanding of the adequacy of these reported data before using them in different transportation applications. This study attempts to systematically assess the quality of the probe data by proposing a method, which determines the minimum sample rate for checking data adequacy. The minimum sample rate is defined as the minimum …

E-Construction Technologies For Efficient Highway Construction Inspections, Dhaivat Patel

Theses and Dissertations--Civil Engineering

Over recent years, organizations such as the Federal Highway Administration and Departments of Transportation across the United States have showed interest in automating highway construction processes. The addition of e-Construction and other advanced technologies can significantly improve the efficiency and safety of highway paving operations, specifically paving inspections. Activities such as collecting load tickets, tracking pavement lay-down temperatures, and monitoring roller movement are antiquated practices that DOT inspectors perform during paving operations. E-Ticketing, Paver Mounted Thermal Profiling, and Intelligent Compaction were proposed to automate paving inspections and were recently tested in two resurfacing pilot projects in the state of Kentucky. …

Basic Turbo Roundabouts As An Alternative To Conventional Double-Lane Roundabouts: Operational Performance Evaluation, Zuhair Elhassy

Electronic Theses and Dissertations

Conventional roundabouts have been prevalent worldwide since the emergence of modern roundabouts in 1966. An innovative design of multilane roundabouts known as turbo roundabouts, however, has been recently introduced as an alternative to conventional multilane roundabouts. Due to several reasons, there has been no general consensus on the operational performance of turbo roundabouts throughout the world. Nationwide, turbo roundabouts have yet to be part of roadway systems, but there is an ongoing project expected to be finished in early 2020. Therefore, this dissertation aims to evaluate the operational performance of a widespread variant of turbo roundabouts, namely basic turbo roundabouts, …

An Initial Exploration Of The 2005 Iowa Rural Interstate Speed Limit Increase Using Linear Regression, Thomas Ryan Cook

Electronic Theses and Dissertations

Speed limit increases, particularly on interstates have been studied and researched many times over the course of the last 50 years in the United States. These research efforts began after the implementation of the National Maximum Speed Law (NMSL), which reduced all speed limits to a maximum of 55-mph. In the years that followed, this restriction was relaxed to 65-mph with the Surface Transportation and Uniform Relocation Assistance Act (STURAA) and ultimately repealed later by the National Highway System Designation Act (NHSDA). Since the repeal, states reacted in myriad of ways and many studies documented the changes of those reactions. …

Synthesis Of Fault Traces In Se Louisiana Relative To Infrastructure, David Culpepper, Elizabeth Chinn Mcdade, Nancye Dawers, Mark Kulp, Rui Zhang

Data

Corresponding data set for Tran-SET Project No. 17GTLSU12. Abstract of the final report is stated below for reference:

"Geological faulting has been implicated as a contributor to subsidence, coastal land-loss and submergence of marshlands in southern Louisiana. This report reviews whether fault motion, either by slow creep or more sudden slip, can cause deformation of engineered structures resulting in increased infrastructure maintenance and repair costs. The impact of surface, or near-surface, geologic faulting on critical infrastructure is insufficiently documented in southeastern Louisiana, but the state has a vast amount of energy-sector subsurface data that to date has been under-utilized for …

Field And Numerical Study For Deteriorating Precast Double-Tee Girder Bridges, Brian Kidd

Electronic Theses and Dissertations

Two deteriorating DT bridges in South Dakota, both over 30-years old, were field tested with a static and dynamic load. From the recorded strain values, the liveload distribution factors (LLDFs) and dynamic load allowance (IM) factors were calculated. The AASHTO LRFD and AASHTO Standard Specifications were compared with the field LLDFs and IMs. It was determined that the AASHTO LRFD Specifications were conservative for deteriorating DT girder bridges, with two exceptions. The AASHTO Standard codified LLDFs were significantly higher than the field LLDFs in all cases. The AASHTO LRFD and AASHTO Standard specifications were conservative when calculating the IM factors …

Validation Of The Highway Capacity Manual Urban Street Travel Time Reliability Methodology Using Empirical Data, Ernest Tufuor, Laurence Rilett

Mid-America Transportation Center: Final Reports and Technical Briefs

The 6th edition of the Highway Capacity Manual (HCM-6) includes the concept of travel time reliability (TTR), which attempts to determine the distribution of average trip travel times over an extended period. TTR is an inherent part of travelers’ route choice decisions and is used by traffic managers to better quantify operations rather than simply using average travel times. The focus of this paper is on the HCM-6 urban street TTR methodology contained in Chapter 17. The approach uses historical data (e.g., weather and volume fluctuations) and simple empirical data (e.g., 1-day volume count) to provide the user with average …

Analysis And Optimization Of Chassis Movements In Transportation Networks With Centralized Chassis Processing Facilities, Timothy Martin Vanderbeek

CGU Theses & Dissertations

This work studies the concept of “Centralized Processing of Chassis,” and its potential impact on port drayage efficiency. The concept revolves around an off-dock terminal (or several off-dock terminals), referred to as Chassis Processing Facilities (CPFs). A CPF is located close to the port, where trucks will go to exchange chassis, thereby reducing traffic at the marine terminals and resulting in reduced travel times and reduced congestion. This work is divided into two major studies: one at the strategic planning level, and one at the operational level for individual trucking companies.

In the first study, an analytical framework for modeling …

Kentucky Traffic Collision Facts 2018, Eric R. Green, Paul A. Ross, Christopher L. Blackden, Kentucky State Police

Kentucky Transportation Center Research Report

KENTUCKY’S TRAFFIC COLLISION FACTS report is based on collision reports submitted to the Kentucky State Police Records Branch. As required by Kentucky Revised Statutes 189.635, “every law enforcement agency whose officers investigate a vehicle accident of which a report must be made...shall file a report of the accident...within ten days after investigation of the accident upon forms supplied by the bureau.” The stated purpose of this requirement is to utilize data on traffic collisions for such purposes as will improve the traffic safety program in the Commonwealth. Data contained in this report are based solely on the observations and judgements …

Reports From The United States Of North America On Railroads, Steamship Travel, Banks And Other Public Undertakings By Franz Anton Ritter Von Gerstner And Description Of A Journey Through The United States Of North America By Clara Von Gerstner, Née Von Epplen-Härtenstein Translated, With An Introduction, By Steven Rowan, Steven Rowan, Franz Anton Ritter Von Gerstner, Clara Von Gerstner, Née Von Epplen-Härtenstein

History Faculty Works

What follows contains a translation of the Berichte aus den Vereinigten Staaten von Nordamerika… [= Reports from the United States of North America] by Franz Anton Ritter von Gerstner, published in Leipzig in August 1839, and posted on the website of “austrian literature online.” It is the companion piece to two other classics of contemporary travel literature, one of them Ritter von Gerstner’s massive description of the transportation system of the United States published by F. A. von Gerstner’s assistant, Ludwig Klein,1 as well as the touching detailed travel narrative of his widow, Clara von Gerstner, Beschreibung einer Reise durch …

Redefining Construction “As-Built” Plans To Meet Current Kentucky Transportation Cabinet Needs, Victoria Lynn Lasley

Theses and Dissertations--Civil Engineering

As-built drawings are the traditional method used by the construction industry to record changes made during construction. As-builts provide valuable information for new design projects as well as rehabilitation and remediation projects. The completeness and accuracy of these plans are essential for transportation industries and their success. While the importance of as-builts is widely recognized, the process of creating them has proven to be difficult. It is a time consuming process and entities often lack the resources necessary to complete accurate and detailed as-builts. After an investigation of current as-built operations within State Transportation Agencies, recommendations have been made to …