Transportation Engineering Commons^™

Effect Of Rheology Modification On Fiber Orientation And Dispersion In 3d-Printed Ultra-High-Performance Concrete, Haodao Li, Alfred Addai-Nimoh, Seongho Han, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The extrusion process in 3D concrete printing (3DCP) facilitates horizontal alignment of steel fibers along the printing direction, thus enhancing the load-bearing capacity of printed elements. However, such shear-induced fiber alignment is highly sensitive to rheological properties. This study investigates how variations in dynamic yield stress (τd) and plastic viscosity (μ), influence the extrudability, fiber orientation and dispersion, and anisotropic mechanical behavior of ultra-high-performance concrete (UHPC). Five viscosity-modifying agent (VMA) types were incorporated at two content levels to modify the rheology of printable UHPC. Results showed that moderate VMA additions improved printability, whereas excessive contents markedly increased τd and μ; …

How Does Competitive Adsorption Between Vma And Pce Influence Yield Stress Of Cement Paste? A Novel Insight From Interparticle Forces And Percolation Threshold, Huamin Sun, Le Teng, Xiaohan Yu, Xin Shu, Zhangli Hu, Jiaping Liu, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Viscosity modifying admixture (VMA) and polycarboxylate superplasticizer (PCE) are often combined to optimize rheological properties of cement-based materials. However, the competitive adsorption of these complex admixtures can greatly influence rheological properties. Many studies have investigated the variation of yield stress due to competitive adsorption between VMA and PCE; but the mechanisms are not fully understood. This study aims to shed a new light on this question in cement paste systems prepared with low water-to-binder ratios of 0.16–0.30. The competitive adsorption of VMA and PCE was quantitatively assessed using the Total Organic Carbon and Ultraviolet-Visible Spectroscopy measurements. The effect of competitive …

Transforming Dredged Sediment Into Reactive Clay: Critical Review Of Calcination, Reactivity, And Sustainable Valorization As Supplementary Cementitious Material, Seongho Han, Sanghwon Wi, Koochul Ji, Keun Hyeok Yang, Farshad Rajabipour, Kamal H. Khayat, Jinyoung Yoon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Dredged sediment (DS) is generated worldwide in large volumes through routine port and waterway maintenance, yet its disposal presents environmental and economic challenges. Recently, calcined dredged sediment (CDS) has emerged as a supplementary cementitious material (SCM), offering a viable alternative to traditional SCMs, such as fly ash and slag cement. This review synthesizes current knowledge on the physical, chemical, and mineralogical characteristics of raw DS and pretreatment strategies aimed at dewatering, organic matter removal, and contaminant stabilization. The effects of calcination on the production of reactive amorphous aluminosilicates are also discussed. Emphasis is placed on physicochemical changes revealed by experimental …

Low-Carbon Concrete For Sustainable Construction: A Comprehensive Review Of Performance Characteristics, Implementation Challenges, And Decarbonization Pathways, Fazel Azarhomayun, Jingjie Wei, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Reducing the carbon footprint of concrete has become a central objective in sustainable construction. Low-carbon concrete (LCC), developed primarily through clinker reduction, supplementary cementitious materials, and alternative binder strategies, offers a promising route for lowering embodied emissions while maintaining the performance requirements of structural concrete. This comprehensive review consolidates the current state of knowledge on LCC, identifies critical research and implementation gaps, and examines its material composition, mixture-design methodologies, performance characteristics, structural applications, implementation challenges, and decarbonization pathways. Single-SCM systems have been reported at clinker-replacement levels approaching 50%, although durability at these replacement levels, particularly carbonation resistance, remains system- and …

Recent Advances In The Rheological Properties Of Ultra-High-Performance Concrete: A Critical Review, Le Teng, Kamal H. Khayat, Jiaping Liu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Ultra-high-performance concrete (UHPC) with adapted rheology continues to attract interest considering the requirement for novel processing techniques such as self-consolidating, pumping, spraying, and three-dimensional (3D) printing. The rheology of UHPC is complex due to its high solid volume fraction, low water content, and wide range of constituent materials that affect its flow properties. This work provides guidance for tailoring the mixture proportioning of UHPC to secure proper rheological properties and performance of UHPC for various applications. In the first part of this work, key physical, physicochemical, and chemical factors that can affect the rheological properties of UHPC are discussed. Rheological …

Computer Vision And Machine Learning Approaches For Defect Detection In 3d-Printed Cementitious Materials: A Systematic Review, Muhammad Ali Musarat, Ruben Paul Borg, Jingjie Wei, Carl James Debono, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

3D printing is evolving at a fast pace in both the manufacturing and construction sectors. These advancements can greatly benefit these industries. However, the 3D printing of concrete structures presents some challenges due to defects in the 3D concrete printed elements. Hence, this study systematically reviews Artificial Intelligence (AI)-driven techniques, such as Computer Vision and Machine Learning, to identify surface defects that can occur in 3D-printed cementitious material structures. The adopted methodology was the PRISMA statement with the aim of reporting the systematic review and meta-analysis. Two well-known databases, Web of Science and Scopus, were utilised for data extraction of …

Toward Sustainable 3d Printable Cementitious Materials: Low-Carbon Design With Fiber Reinforcement, Nima Mahmoudzadeh Vaziri

Miners Solving for Tomorrow Research Conference

3D printing of cementitious materials, as an emerging construction technology, faces challenges in both mechanical performance and sustainability. Conventional mixture designs rely on high cement contents, leading to increased CO2 emissions, while printed elements often exhibit brittle behavior with limited crack resistance and reduced post-cracking performance. This study investigates the development of low-carbon 3D printed cementitious composites using environmentally friendly supplementary cementitious materials (SCMs) and fillers, combined with fiber reinforcement to enhance mechanical performance. Locally available SCMs and fillers were incorporated to significantly reduce cement content (>40%) and improve sustainability. Fiber reinforcement was introduced to mitigate brittleness and enhance …

New Insights Into Dynamic Evolution Of Colloidal Network Structure During Early-Age Hardening Of Cementitious Materials, Hengrui Liu, Kaiyin Zhao, Shipeng Zhang, Hanghua Zhang, Shuangshuang Liu, Lucen Hao, Hongyan Ma, Kamal Khayat, Chi Sun Poon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The evolution of microstructure in cementitious materials during their transition from fluid to solid state plays a critical role in determining their ultimate mechanical strength and overall performance. This hydration stage primarily involves a dynamic densification process occurring within the colloidal network. However, the field of cement-based materials currently lacks a comprehensive theoretical framework and associated parameters capable of effectively characterizing the specific structural regions within this network. In this study, we propose an Improved Particle Linkage (IPL) theory for describing the strength, types, and quantities of particle linkages within colloidal network. The IPL theory classifies the internal network structure …

Advances And Challenges In Nano-Modified Cementitious Composites: Mechanisms, Dispersion Strategies, And Impact On Mechanical Properties, Fatemeh Mohammadi Ghahsareh, Pengwei Guo, Nusrath Jaha, Yi Bao, Kamal H. Khayat, Weina Meng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Nanomaterials are increasingly utilized to enhance the mechanical properties, durability, and functionality of concrete materials but face challenges such as agglomeration and uneven dispersion in cementitious systems, which can offset the intended improvements. This paper reviews the advances and challenges associated with nano-modified cementitious composites, elucidating fundamental mechanisms and highlighting strategies for overcoming the challenges through experimental and computing techniques. The reviewed contents include (1) the classification of nanomaterials commonly used in cementitious systems and the mechanisms through which they enhance the mechanical properties of cementitious composites; (2) challenges of nanomaterials such as agglomeration in water, re-agglomeration in cementitious systems, …

Co2-Induced Changes In Rheology, Structural Evolution, And Particle Characteristics Of Cement Paste, Seongho Han, Tae Yong Shin, Seung Mo Kim, Jae Hong Kim, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The injection of carbon dioxide (CO₂) into cementitious systems has emerged as a promising approach to enhancing sustainability in concrete production. This study explores the impact of CO₂ injection on the rheological behavior, structural build-up, and particle size evolution of cement paste by systematically varying the water-to-cement ratio (w/c) (0.35, 0.4, and 0.5) and CO₂ concentration (0.06, 0.28, and 0.84 mol). Rheological analysis revealed a significant increase in initial yield stress with CO₂ injection. Using the Modified Bingham model, yield stress increased by 72 % and 150 % for 0.28- and 0.84-mol CO₂, …

Influence Of Mixing Duration And Absorption Characteristics Of Superabsorbent Polymers On The Fresh And Hardened Properties Of High-Performance Concrete, Yu Cun Gu, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigates the combined influence of superabsorbent polymers (SAPs) with distinct absorption kinetics and extended mixing sequences on the rheological, mechanical, and transport properties of high-performance concrete (HPC). Two SAPs—an ionic acrylamide-co-acrylic acid copolymer (SAP-P) and a non-ionic acrylamide polymer (SAP-B)—were incorporated at an internal curing level of 100%. The impact of extended mixing times (3, 5, and 7 min) following SAP addition was systematically evaluated. Results showed that longer mixing durations led to increased superplasticizer demand and higher plastic viscosity due to continued water absorption by SAPs. However, yield stress remained relatively stable owing to the dispersing effect …

Treatment And Activation Effects On Kaolinite-Based Earth Concrete, Mojtaba Kohandelnia, Maroua Zerzouri, Ammar Yahia, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Self-consolidating earth concrete (SCEC) addresses the long construction process of conventional earthen constructions and their structural limitations, while further efforts are needed to enhance its sustainability. This study explores the development of a kaolinite-based self-consolidating earth paste (SCEP) due to their blended powder system, incorporating raw and treated (calcined and ground-calcined) kaolinite under various activation techniques, such as water hydration, sodium hexametaphosphate (NaHMP), and sodium hydroxide (NaOH) activation. The synergistic effect of calcination and mechanosynthesis on rheological, mechanical, structural, and microstructural properties of SCEP were investigated. Mechanically treated kaolinite increased yield stress, plastic viscosity, storage modulus evolution, and build-up index, …

Digital Fabrication With Fiber-Reinforced Concrete, Haodao Li, Kamal H. Khayat

Miners Solving for Tomorrow Research Conference

No abstract provided.

Underlying Mechanisms Of The Effect Of Microfines Of Manufactured Sand On Non-Linear Structural Build-Up Of Cement Paste, Jiang Zhu, Jiaping Liu, Kamal H. Khayat, Xin Cheng, Wei Zhao, Zhen Li, Xin Shu, Yongbo Huang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The rheological properties of cement-based materials made with manufactured sand vary with the content and physio-chemical properties of microfines in the sand. However, the evaluation of rheological properties regarding the structural build-up at early-age hydration remains challenging for the cementitious materials prepared with different manufactured sands, due to complicated underlying structuration mechanisms. This paper studies the effect of disparate microfines of different manufactured sands on the non-linear growth of static yield stress of cement pastes at rest. The paste mixtures were prepared with 0.40 and 0.275 water-to-cement mass ratio (W/C) and had a fixed mini-slump flow of 240 ± 5 …

Effect Of Shrinkage-Mitigating Materials, Fiber Type, And Repair Thickness On Flexural Behavior Of Beams Repaired With Fiber-Reinforced Self-Consolidating Concrete, Jingjie Wei, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

While self-consolidating concrete (SCC) has emerged as a highly effective approach for the repair of concrete structures, there have been few investigations regarding the effect of the combination of different fiber and shrinkage-mitigating material types (shrinkage-reducing admixture, SRA; superabsorbent polymer, SAP; and expansive agent, EA) on the flexural behavior of repaired structures. This study aims to explore the influence of three different shrinkage-mitigating materials (1.25%–2.5 % SRA, 4%–8% EA, and 0.2%–0.4 % SAP), four fiber types (two macro synthetic fibers, MSFA and MSFB; 5D hooked steel fibers, 5D; a combination of 80 % 3D hooked steel +20 % short steel …

Flexural Post-Cracking Performance Of Macro Synthetic Fiber Reinforced Super Workable Concrete Influenced By Shrinkage-Reducing Admixture, Jingjie Wei, Nima Farzadnia, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Most literature has focused on the effect of shrinkage-reducing admixture (SRA) in shrinkage mitigation resistance of concrete. This study aims to examine the impact of SRA on the efficiency of macro synthetic fibers (MSF) in enhancing the flexural post-cracking behavior of fiber-reinforced super workable concrete (FR-SWC). A comparative analysis of the influence of fiber combinations on the flexural post-cracking behavior of beams is also included. Results showed that a higher dosage of SRA, particularly at 5 % by mass of binder, had a noticeable negative impact on flexural post-cracking performance of beams while exhibiting positive effect on workability and shrinkage …

Optimization Of Transit Smart Card Data Publishing Based On Differential Privacy, Chenxi Chen

Masters Theses

“Privacy budget allocation is a key step of the differential privacy (DP)-based privacy-preserving data publishing (PPDP) algorithm development, as it directly impacts the data utility of the released dataset. This research describes the development of an optimal privacy budget allocation algorithm for transit smart card data publishing, with the goal of publishing non-interactive sanitized trajectory data under a differential privacy definition. To this end, after storing the smart card trajectory data with a prefix tree structure, a query probability model is built to quantitatively measure the probability of a trajectory location pair being queried. Next, privacy budget is calculated for …

Infrastructure Systems Modeling Using Data Visualization And Trend Extraction, Jacob Marshal Hale

Doctoral Dissertations

“Current infrastructure systems modeling literature lacks frameworks that integrate data visualization and trend extraction needed for complex systems decision making and planning. Critical infrastructures such as transportation and energy systems contain interdependencies that cannot be properly characterized without considering data visualization and trend extraction.

This dissertation presents two case analyses to showcase the effectiveness and improvements that can be made using these techniques. Case one examines flood management and mitigation of disruption impacts using geospatial characteristics as part of data visualization. Case two incorporates trend analysis and sustainability assessment into energy portfolio transitions.

Four distinct contributions are made in this …

Correction To: Recommendations Of Rilem Tc 260-Rsc For Using Superabsorbent Polymers (Sap) For Improving Freeze–Thaw Resistance Of Cement-Based Materials (Materials And Structures, (2019), 52, 4, (75), 10.1617/S11527-019-1375-4), Viktor Mechtcherine, Christof Schröfl, Michaela Reichardt, Agnieszka J. Klemm, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Agnieszka J. Klemm is affiliated to Glasgow Caledonian University, Glasgow, UK.

Seismic Behavior Of Composite Bridge Columns, Mohanad M. Abdulazeez

Doctoral Dissertations

“This study investigates experimentally and numerically the seismic behavior of large-scale hollow-core fiber-reinforced polymer-concrete-steel (HC-FCS) innovative bridge columns as a sustainable approach to endure and rapidly recover from natural disasters such as earthquakes. The HC-FCS column consisted of a concrete shell sandwiched between an outer fiber-reinforced polymer (GFRP) tube and an inner steel tube to provided continuous confinement for the concrete shell along with the height of the column. The columns have a slender inner steel tube with diameter-to-thickness (D_s/t_s) ratios ranged between 85 to 254. Each steel tube was embedded into the footing, while the …

Developing Restoration Schemes For A Road Transportation Network In The Event Of A Disaster, Ebin Antony

Masters Theses

"Transportation systems such as rail, road, and waterways are key component of critical infrastructure systems, providing connectivity between other components to enable the production and distribution of goods and services. During large scale disasters such as earth quakes and floods, this connectivity is disrupted, restricting or completely halting the flow of goods and services. To ensure that the connectivity between the different modes of transportation are restored in an aftermath of these disruptions, the interdependence between them and the importance of individual elements to the overall connectivity have to be studied and formulated to develop a system-level restoration plan. This …

Environmental Hazard Identification, Assessment And Control For A Sustainable Maritime Transportation System, Lizzette Marie Pérez Lespier

Doctoral Dissertations

"A demand exists to contribute towards the widening awareness of the need for sustainable maritime development and for coordinated maritime policies worldwide. Maritime shipping is considered the most eco-efficient mean of transportation and yet, is responsible for negative environmental impacts.

This dissertation focuses on developing data-driven decision support tools to evaluate the sustainable performance of MTS by focusing on the elements of the MTS that place stress on the environment. The first research contribution is a System Dynamics simulation model that examines the MTS resiliency after an extreme event and determines the sequence needed to restore the ocean-going port to …

A Report On "Relieving Traffic Congestion On The Southern Pacific Between Oregon City, Oregon And Woodburn, Oregon.", Henri Chomeau

Missouri School of Mines and Metallurgy Reports

The Division Engineer of the Portland Division, Southern Pacific Company, ordered the Signal Supervisor of the same division, to devise some improvements in the signal system in order to make train movements between Oregon City, Oregon and Woodburn, Oregon more rapid and relieve congestion over this part of the single-track steam line. The following system has been worked out by the Signal Department.

Location, Construction, And Drainage Of Common Roads, Edward B. Summers

Bachelors Theses

To write upon, and do justice to the subject of common roads, it is necessary that one should be familiar with every variety of them. The roads in some of the advanced and highly civilized communities are of a most admirable character; while in the new and thinly populated countries, they are found deficient in nearly all the attributes of good roads. Only a few kinds that may be in some of the most populous districts will be here designated.