Transportation Engineering Commons^™

Estimating Vehicle Infrastructure: Downtown Albuquerque, New Mexico, Zachery Phillip Baiamonte

Architecture and Planning ETDs

Cities have little knowledge about their parking infrastructure despite clear evidence that abundant parking has environmental, economic, and transportation consequences. The objective of this thesis is to illustrate the need to accurately estimate the area dedicated to vehicle infrastructure (parking lots and streets) within urban areas. I focused on a method that estimated the vehicle infrastructure area within the Downtown Core of Albuquerque, New Mexico, by cross-referencing geospatial cadastral data with minimum parking requirements. Three parking space types were identified: 1) parking in structures; 2) surface parking (parking lots and residential driveways); and 3) on-street parking. To illustrate the need …

Inequity Of Access Across America: A Spatial, Temporal, And Modal Disparity Analysis, Sanju Maharjan

Theses and Dissertations

The overarching goal of this dissertation is to examine the spatial, temporal, and modal disparity of access across America. This is achieved by posing three research objectives. The first objective determines the spatial and temporal disparity of transit and automobile access gap, its impact on transit use, and its socioeconomic and built environment correlates. The second objective examines the spatial and temporal disparity of slightly and extremely risky bike infrastructure and measures the social inequity of access to bike infrastructure. The third objective indicates spatial transit access mismatch between high- and low-wage employment across metropolitans. Three findings are discerned. First, …

Improving Building Cfd Peak Pressure Computation Using Les With A Focus On Inflow Turbulence Methods And Grid Spacing Size., Zahra Mansouri

Graduate Theses and Dissertations

Structural failures by extreme winds often leads to economic losses and even deaths. Proper design of buildings requires accurate estimation of wind loads to prevent structural damage. Using routine guidelines generally leads to the underestimation of buildings’ peak pressures, in which most failures occur. To estimate wind loads more accurately three different methods (i.e., field measurement, wind tunnel (WT), and computational fluid dynamics (CFD)) are in use. A well-validated CFD provides more flow field details at lower costs compared to field measurements and WT. As strong winds are extremely turbulent, the effects of turbulence in wind should be incorporated into …

Comparative Analysis Of 3d Printed Bridge Construction In Louisiana, Amirhosein Jafari, Ali Kazemian, Sarah Ataei

Data

A construction 3D printing system could result in automated infrastructure development at reduced cost and time, significantly boosting overall productivity. Although there has been a growing interest in using construction 3D printing for projects such as house construction, implementing this innovative technology for infrastructure development, particularly bridge construction, has not been investigated as extensively. This study aims to compare the environmental impact of precast and 3D concrete printing (3DCP) techniques with a pedestrian bridge case study, located in Louisiana, where the bridge elements were 3D printed off-site and then transported and assembled on the bridge site. A detailed cradle-to-site life …

Comparative Analysis Of 3d Printed Bridge Construction In Louisiana, Amirhosein Jafari, Ali Kazemian, Sarah Ataei

Publications

A construction 3D printing system could result in automated infrastructure development at reduced cost and time, significantly boosting overall productivity. Although there has been a growing interest in using construction 3D printing for projects such as house construction, implementing this innovative technology for infrastructure development, particularly bridge construction, has not been investigated as extensively. This study aims to compare the environmental impact of precast and 3D concrete printing (3DCP) techniques with a pedestrian bridge case study, located in Louisiana, where the bridge elements were 3D printed off-site and then transported and assembled on the bridge site. A detailed cradle-to-site life …

Development Of Ultra-High Performance Engineered Geopolymer Composites (Uhp-Egcs), Hassan Noorvand, Miladin Radovic, Marwa Hassan, Svetlana Sukhishvili, Gabriel Arce, Ruwa Abufarsakh, Adriana A. Alvarado, Oscar Huang, Sang Zhen

Data

This study investigated the possibility of developing novel UHP-EGC materials for the repair and new construction of transportation infrastructure in Region 6 by utilizing locally available resources. To this end, the geopolymers (GPs) in this study were synthesized by activating metakaolin (MK) with potassium silicate and sodium silicate solutions. The solutions were manufactured in the laboratory by dissolving silica fume and potassium hydroxide (KOH) or sodium hydroxide (NaOH) in deionized water. MK-based GP binders, mortars, and fiber-reinforced composites were manufactured and evaluated to determine their density, compressive strength, tensile properties, and slant shear bond strength to Portland cement concrete (PCC). …

Spf-R Online User Guide, Eric Green, Paul Ross, Christopher Blackden, William Staats, Reginald Souleyrette

Kentucky Transportation Center Research Report

SPF-R Online greatly improves and simplifies the SPF development process. Building on the original SPF-R script, the online tool eliminates many of the technical barriers associated with the original process, allowing for a much larger audience to take advantage of SPF-R’s capabilities. Like the original SPF-R script, SPF-R Online lets users quickly explore the effect of roadway network heterogeneity on SPF development, compare CURE plots , and compare goodness-of-fit measures to decide which SPF is most appropriate for a given dataset.

Field Monitoring Of Joint-Less Curved Integral Abutment Bridge In Nebraska, Ramin Ziaei, Yusuf Alhowaidi, Chungwook Sim, Jongwan Eun, Seunghee Kim, Chung Rak Song

Nebraska Department of Transportation: Research Reports

The research objective of this project is to study the behavior of the curved full integral abutment bridge designed in Nebraska through field monitoring and numerical simulation to 1) understand and model the complex short-term and long-term behavior of curved integral abutment bridges, 2) evaluate if the details provided in Nebraska (pile embedment over 4 ft into the abutment) can be expanded for wider design and construction practices (longer spans and larger curvature for curved bridges), and 3) better maintain existing full curved integral bridges in Nebraska based on the findings of this study (revise and optimize design, if needed). …

Use Of Harsh-Braking Data From Connected Vehicles As A Surrogate Safety Measure, Nathaniel Patrick Edelmann

Boise State University Theses and Dissertations

Traffic safety may be analyzed with the use of surrogate safety measures, measures of safety that do not incorporate collision data but rather rely on the concept of traffic conflicts. Use of these measures provides several benefits over use of more traditional analysis methods with historical crash data. Surrogate measures eliminate the need to wait for crashes to occur to conduct a safety analysis. The amount of time required for enough crash data to accumulate can be significant, delaying safety analyses. Similarly, these measures allow for safety analysis to be conducted prior to crashes occurring, potentially calling attention to hazardous …

Measurement And Evaluation Of Roadway Geometry For Safety Analyses And Pavement Material Volume Estimation For Resurfacing And Rehabilitation Using Mobile Lidar And Imagery-Based Point Clouds, Leonildo Nelson Cassule

All Dissertations

Roadway safety is a multifaceted issue affected by several variables including geometric design features of the roadway, weather conditions, sight distance issues, user behavior, and pavement surface condition. In recent years, transportation agencies have demonstrated a growing interest in utilizing Light Detecting and Ranging (LiDAR) and other remote sensing technologies to enhance data collection productivity, safety, and facilitate the development of strategies to maintain and improve existing roadway infrastructure. Studies have shown that three-dimensional (3D) point clouds acquired using mobile LiDAR systems are highly accurate, dense, and have numerous applications in transportation. Point cloud data applications include extraction of roadway …

Development Of Ultra-High Performance Engineered Geopolymer Composites (Uhp-Egcs), Hassan Noorvand, Miladin Radovic, Marwa Hassan, Svetlana Sukhishvili, Gabriel Arce, Ruwa Abufarsakh, Adriana A. Alvarado, Oscar Huang, Sang Zhen

Publications

This study investigated the possibility of developing novel UHP-EGC materials for the repair and new construction of transportation infrastructure in Region 6 by utilizing locally available resources. To this end, the geopolymers (GPs) in this study were synthesized by activating metakaolin (MK) with potassium silicate and sodium silicate solutions. The solutions were manufactured in the laboratory by dissolving silica fume and potassium hydroxide (KOH) or sodium hydroxide (NaOH) in deionized water. MK-based GP binders, mortars, and fiber-reinforced composites were manufactured and evaluated to determine their density, compressive strength, tensile properties, and slant shear bond strength to Portland cement concrete (PCC). …

Data-Driven Analysis For Facility Management In Higher Education Institution, Ashish Kumar Pampana, Jungho Jeon, Soojin Yoon, Theodore J. Weidner, Makarand Hastak

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Planned Preventive Maintenance (PPM) and Unplanned Maintenance (UPM) are the most common types of facility maintenance. This paper analyzes current trends and status of Facility Management (FM) practice at higher education institutions by proposing a systematic data-driven methodology using Natural Language Process (NLP) approaches, statistical analysis, risk-profile analysis, and outlier analysis. This study utilizes a descriptive database entitled "Facility Management Unified Classification Database (FMUCD)" to conduct the systematic data-driven analyses. The 5-year data from 2015 to 2019 was collected from eight universities in North America. A preprocessing step included but was not limited to identifying common data attributes, cleaning noisy …

The Impact Of Murals On Traffic Safety: A Behavior And Crash Analysis, Maria Cecelia Cruz

Civil Engineering ETDs

ABSTRACT

This research analyzed changes in motor vehicle volumes and motor vehicle speeds after the installation of an intersection mural in Albuquerque, NM and changes in crash frequency after mural installations in Philadelphia, PA. Data was collected manually on site for the Albuquerque study and secondary data – including installation dates and physical characteristics – were used for the Philadelphia crash analyses. Statistics were computed to determine trends in motor vehicle speeds and volumes relative to the Albuquerque mural installation. A geographic information system (GIS) spatial analysis and t-test statistical analyses were used to determine which Philadelphia murals saw significant …

Toward A Safer Transportation System For Senior Road Users, Saba Doulabi

LSU Doctoral Dissertations

Senior pedestrians and drivers (65 years and older) are among the most vulnerable road users. As the population of seniors rise, concerns regarding older adults' traffic safety are growing. The advantages of using autonomous vehicles, innovative vehicle technologies, and active transportation are becoming more widely recognized to improve seniors' mobility and safety. This behooves researchers to further investigate senior road users’ safety challenges and countermeasures. This study contributes to the literature by achieving two main goals. First, to explore contributing factors affecting the safety of older pedestrians and drivers in the current transportation system. Second, to examine seniors’ perceptions, preferences, …

Rapid Pothole Repair In Concrete Bridge Decks, Abheetha Peiris, Issam Harik

Kentucky Transportation Center Research Report

Using traditional methods to repair potholes in reinforced concrete (RC) bridge decks is time-consuming and requires significant manpower and equipment. However, commercially available epoxies and similar materials provide a repair option that does not require saw cutting the deck around the pothole, concrete removal, and replacement. Researchers laboratory tested three epoxies to identify which is best for pothole repairs. Based on assessments of substrate penetration times and set times for epoxy and epoxy mortar, as well as compressive strength gain over time for epoxy mortar, researchers selected Sikadur 52 for static and dynamic bending tests using small-scale beams with simulated …

Rebar-Free 3d Printing Of Transportation Infrastructure, Ali Kazemian, Marwa Hassan, Hassan Noorvand, Gabriel Arce, Hassan Ahmed, Ilerioluwa Giwa

Data

This study investigates the fresh and hardened-state properties of printing mixtures including different dosages of steel fibers, especially at higher dosages which have not been investigated before. This study also considers the effects of other parameters such as sand-to-powder ratio and the limestone content on the properties of steel fiber reinforced printing materials, to reduce the Portland cement content which has a high carbon footprint. The obtained experimental results revealed that high-performance materials incorporating up to 2.5% steel fibers (by volume) can be successfully 3D printed. The mechanical properties of the reinforced mixtures improved significantly at high fiber dosages (2% …

Low-Cost Sustainable Engineered Geopolymer Composites (Egcs) For Repair And New Construction Of Transportation Infrastructure, Hassan Noorvand, Marwa Hassan, Miladin Radovic, Svetlana Sukhishvili, Gabriel Arce, Ruwa Abufarsakh, Adriana A. Alvarado, Oscar Huang, Sang Zhen

Data

This study evaluated the use of cost-effective alternative materials in the formulation of novel low-cost Engineered Geopolymer Composite (EGC) materials for repair and new construction of transportation infrastructure in Region 6. Previous studies and reports have shown that EGCs have excellent mechanical properties, which makes them an eco-friendly and more sustainable alternative to Engineered Cementitious Composites (ECCs). However, the mass adoption of these emerging composites is expected to be hindered by their cost, which is mainly driven by the use of PVA reinforcing fibers, silica fume (SF), and manufactured microsilica sand (MS). To address this key shortcoming, novel low-cost EGC …

Development Of Robotics & Automation Roadmap For Road Construction/Maintenance Projects, Ashrant Aryal, Chao Wang, Chintan Vijay Vora, Sueed A. Willoughby

Data

Over the past few decades, there have been no significant improvements in the construction industry's productivity. Outside the construction industry, robots have proven to be beneficial in improving productivity, safety, and quality. There is a growing interest in adopting robots in the construction industry to address these issues. As robots get introduced to the project sites, human-robot interaction becomes an important consideration for wide-scale adoption. The success of deploying robots in the construction industry depends on how well humans collaborate with the robots. This project focused on investigating the perception of various construction industry stakeholders in adopting robots in their …

Rebar-Free 3d Printing Of Transportation Infrastructure, Ali Kazemian, Marwa Hassan, Hassan Noorvand, Gabriel Arce, Hassan Ahmed, Ilerioluwa Giwa

Publications

This study investigates the fresh and hardened-state properties of printing mixtures including different dosages of steel fibers, especially at higher dosages which have not been investigated before. This study also considers the effects of other parameters such as sand-to-powder ratio and the limestone content on the properties of steel fiber reinforced printing materials, to reduce the Portland cement content which has a high carbon footprint. The obtained experimental results revealed that high-performance materials incorporating up to 2.5% steel fibers (by volume) can be successfully 3D printed. The mechanical properties of the reinforced mixtures improved significantly at high fiber dosages (2% …

Resilient 3d-Printed Civil Infrastructure With Ultra-High Performance Engineered Cementitious Composites (Uhpeccs), Hassan Noorvand, Marwa Hassan, Ali Kazemian, Gabriel Andres Arce Amador, Daniel E. Game

Publications

This study aims to develop and evaluate UHP-ECC materials for 3DP applications. To achieve this, the rheological properties of the cementitious composites were designed to accommodate 3DP functionality. Additionally, this study aimed to evaluate the hardened properties of the 3D-printed UHP-ECCs and compare them to the cast UHP-ECCs. Furthermore, the effect of variables such as sand-to-binder (S/B), fly ash-to-cement ratio (FA/C), and high-range water reducer (HRWR) content on the fresh and hardened properties of the 3D printable mixtures were evaluated. Fresh properties of mixtures were assessed by means of the flowability test, setting time test, and printability test. Hardened properties …

Resilient 3d-Printed Civil Infrastructure With Ultra-High Performance Engineered Cementitious Composites (Uhpeccs), Hassan Noorvand, Marwa Hassan, Ali Kazemian, Gabriel Andres Arce Amador, Daniel E. Game

Data

This study aims to develop and evaluate UHP-ECC materials for 3DP applications. To achieve this, the rheological properties of the cementitious composites were designed to accommodate 3DP functionality. Additionally, this study aimed to evaluate the hardened properties of the 3D-printed UHP-ECCs and compare them to the cast UHP-ECCs. Furthermore, the effect of variables such as sand-to-binder (S/B), fly ash-to-cement ratio (FA/C), and high-range water reducer (HRWR) content on the fresh and hardened properties of the 3D printable mixtures were evaluated. Fresh properties of mixtures were assessed by means of the flowability test, setting time test, and printability test. Hardened properties …

Best Practices For Highway Project Scoping, Jeff Jasper, Samantha Wright, Jon Wilcoxson, Robin Baskette, Christopher Van Dyke

Kentucky Transportation Center Research Report

One of the Kentucky Transportation Cabinet’s (KYTC) foremost priorities in fulfilling its mission is to deliver successful projects — quality solutions that meet the defined scope and are delivered on time and within the budget specified in the Highway Plan. When a project scope is not clearly defined or uncertain, revisions may take place after the project is already underway, leading to delays or overpromising what can be delivered. Ideally, a reliable, decisive project scope is defined in the early phases of the highway project development process. The scope should include a project definition that clearly communicates the project scope’s …

Does Transit Service Reliability Influence Ridership?, Srinivas S. Pulugurtha, Raunak Mishra, Sravya L. Jayanthi

Mineta Transportation Institute

This research focused on analyzing the association between transit service reliability indicators and ridership. Further, the effect of road network, demographic, socioeconomic, and land use characteristics on transit service reliability was analyzed. The analysis was conducted at a bus stop level. Bus arrival/departure and ridership data from the Charlotte Area Transit System (CATS) was obtained. The road network, demographic, socioeconomic, and land use characteristics were captured within 0.25-mile and 0.50-mile buffers. Pearson correlation analysis was conducted to understand the association between road network, demographic, socioeconomic, and land use characteristics and bus transit service reliability measures. The results show that bus …

Travel Behavior Change And Economic Transition In Gentrified Neighborhoods, Maryam Izadi

LSU New Orleans Theses and Dissertations

Post-industrial cities in the US have experienced social and economic transitions, mostly in declining downtown neighborhoods. This process, known as gentrification, typically involves revitalization that reverses the decline and disinvestment in inner-city neighborhoods. The industrial shift increased the demand for housing near downtown. The employment of college-educated and high-skill workers has been centralized, while low-skilled jobs continue to decline downtown. While the impacts of gentrification on housing and residential displacement is frequently investigated, little attention has been given to its impact on travel behavior change and economic transition, which is the focus of this research. Change in travel behavior is …

Low-Cost Sustainable Engineered Geopolymer Composites (Egcs) For Repair And New Construction Of Transportation Infrastructure, Hassan Noorvand, Marwa Hassan, Miladin Radovic, Svetlana Sukhishvili, Gabriel Arce, Ruwa Abufarsakh, Adriana A. Alvarado, Oscar Huang, Sang Zhen

Publications

This study evaluated the use of cost-effective alternative materials in the formulation of novel low-cost Engineered Geopolymer Composite (EGC) materials for repair and new construction of transportation infrastructure in Region 6. Previous studies and reports have shown that EGCs have excellent mechanical properties, which makes them an eco-friendly and more sustainable alternative to Engineered Cementitious Composites (ECCs). However, the mass adoption of these emerging composites is expected to be hindered by their cost, which is mainly driven by the use of PVA reinforcing fibers, silica fume (SF), and manufactured microsilica sand (MS). To address this key shortcoming, novel low-cost EGC …

Development Of Robotics & Automation Roadmap For Road Construction/Maintenance Projects, Ashrant Aryal, Chao Wang, Chintan Vijay Vora, Sueed A. Willoughby

Publications

Over the past few decades, there have been no significant improvements in the construction industry's productivity. Outside the construction industry, robots have proven to be beneficial in improving productivity, safety, and quality. There is a growing interest in adopting robots in the construction industry to address these issues. As robots get introduced to the project sites, human-robot interaction becomes an important consideration for wide-scale adoption. The success of deploying robots in the construction industry depends on how well humans collaborate with the robots. This project focused on investigating the perception of various construction industry stakeholders in adopting robots in their …

Effect Of Weather Events On Travel Time Reliability And Crash Occurrence, Sonu Mathew, Srinivas S. Pulugurtha

Mineta Transportation Institute

The magnitude of the effect of adverse weather conditions on road operational performance varies with the type of weather condition and the road characteristics of the road links and adjacent links. Therefore, the relationship between weather and traffic is always a concern to traffic engineers and planners, and they have extensively explored ways to integrate weather information into transportation systems. Understanding the influence of weather on operational performance and safety helps traffic engineers and planners to proactively plan and manage transportation systems. The main objective of this research is to evaluate the effect of adverse weather conditions on travel time …

Development Of A Smartphone Application As An Asset To Pavement Management Engineers, Smartp3m, Damien Stephens

Electrical Engineering Theses

An application specific multi-platform smartphone application can utilize on-board accelerometer, gyroscope, and GPS sensors, along with software derived signals from the same sensors, to sample vibrational and geolocation datasets to capture pavement distresses such as potholes when mounted in a standardized configuration in a vehicle. Several observations were made with regard to the signals obtained from the accelerometer, gyroscope, and GPS sensors, and it was determined that the raw sensor outputs are capable of sampling statistically significant datasets which can be used to distinguish pavement distress from normal driving conditions. Furthermore, an approximate sensor noise margin is established, and a …

Evaluation Of The Operation Of Lighthouses And Beacons In The Gulf Of Suez, Tamer Saber Abdelhafez Elsayed

World Maritime University Dissertations

No abstract provided.

Comparative Analysis Of Cloud-Based Server And Conventional Server Of Simulators For Marine Engineering, Jose Maria Razon Nalus

World Maritime University Dissertations

No abstract provided.