Navigation, Guidance, Control and Dynamics Commons^™

Artificial Inhomogeneous Tapered Impedance Sheet Characterization And Applications, Jeffrey P. Massman

Theses and Dissertations

The ability to manipulate a complex impedance sheet about a PEC or general dielectric cylinder of arbitrary diameter to control the overall scattering characteristics at particular angles for shielding or scattering applications is presented. It is shown that with the capability to readily control both the real and imaginary components of a percolated lossy film's effective impedance, specific impedance distributions can be obtained to effectively direct the overall nulls in the bistatic scattering pattern. The exact approach only requires negligible truncation error of the matrix solution and can be applied to cylinders of arbitrary size. This approach relies on general …

Disturbance Observer: Design And Flight Test Of A Large Envelope Flight Controller, Donevan A. Rein

Theses and Dissertations

A new flight controller was evaluated through piloted simulation and flight test conducted at the USAF Test Pilot School. The controller, commonly called a disturbance observer, uses inertial sensor feedback routed through a simple control architecture that acts to force the desired response while rejecting sensor noise and atmospheric disturbances. The investigation included both handling qualities testing in the Octonian simulator at the Air Force Research Laboratories Air Vehicle Directorate, and initial flight test conducted as part of a Test Management Project at the USAF TPS. Simulation produced positive results with desired performance throughout a wide flight envelope. In addition, …

Orbit Maneuver For Responsive Coverage Using Electric Propulsion, Timothy S. Hall

Theses and Dissertations

The use of continuous electric propulsion to manipulate a satellite’s orbit offers significant potential for enhancing coverage of a target in ways not previously considered. Elliptical orbits utilizing a very low perigee can facilitate access to the surface and atmosphere of the Earth at sub-ionosphere altitudes while counteracting atmospheric drag forces using continuous electric propulsion. Additionally, in-plane and out-of-plane manipulation of both circular and elliptical orbits can allow for passage of a satellite over a target at a given time. Sustained low perigee orbit was modeled with an initial perigee altitude of 100 km and various apogee altitudes to derive …

Mission Analysis For Multiple Rendezvous Of Near-Earth Asteroids Using Earth Gravity Assist, Uriah J. Tobey

Theses and Dissertations

The Jet Propulsion Laboratory (JPL) catalog of near-Earth objects (NEOs) such as asteroids and comets contains over 6600 asteroids and 150 comets as of February of 2010. This includes over 1000 potentially hazardous asteroids, or objects with orbits that pass close enough to Earth to pose a potential impact threat. The asteroid community believes there are a significant number of objects still undiscovered, which makes finding, tracking, and calculating missions to study these objects an active area of research. This study was based on finding orbit solutions using Earth gravity assist to visit one near-Earth object (NEO) a year for …

Global Navigation Satellite System Software Defined Radio, Jason M. Mcginthy

Theses and Dissertations

The GNSS world is quickly growing. The United States’ GPS, the European Union’s Galileo, China’s Compass, and Russia’s GLONASS systems are all developing or modernizing their signals, and there will soon be more navigation satellites in space than ever before. The goal of this research was to develop an initial capability for an AFIT GNSS software receiver. This software receiver is intended to be used for research purposes at the Advanced Navigation Technology (ANT) Center. First a GPS-only software receiver was built. It successfully acquired, tracked, and provided reasonable position estimates. Next, the receiver was successfully modified to acquire and …

Monocular Vision Localization Using A Gimbaled Laser Range Sensor, Don J. Yates

Theses and Dissertations

There have been great advances in recent years in the area of indoor navigation. Many of these new navigation systems rely on digital images to aid an inertial navigation estimates. The Air Force Institute of Technology (AFIT) has been conducting research in this area for a number of years. The image-aiding techniques are centered around tracking stationary features in order to improve inertial navigation estimates. Previous research has used stereo vision systems or terrain constraints with monocular systems to estimate feature locations. While these methods have shown good results, they do have drawbacks. First, as unmanned exploration vehicles become smaller …

System Integration And Attitude Control Of A Low-Cost Spacecraft Attitude Dynamics Simulator, Ryan L. Kinnett

Master's Theses

The CalPoly Spacecraft Attitude Dynamics Simulator mimics the rotational dynamics of a spacecraft in orbit and acts as a testbed for spacecraft attitude control system development and demonstration. Prior to this thesis, the simulator platform and several subsystems had been designed and manufactured, but the total simulator system was not yet capable of closed-loop attitude control. Previous attempts to make the system controllable were primarily mired by data transport performance. Rather than exporting data to an external command computer, the strategy implemented in this thesis relies on a compact computer onboard the simulator platform to handle both attitude control processing …

Adaptive Control Applied To The Cal Poly Spacecraft Attitude Dynamics Simulator, Matthew C. Downs

Master's Theses

The goal of this thesis is to use the Cal Poly Spacecraft Attitude Dynamics Simulator to provide proof of concept of two adaptive control theories developed by former Cal Poly students: Nonlinear Direct Model Reference Adaptive Control and Adaptive Output Feedback Control. The Spacecraft Attitude Dynamics Simulator is a student-built air bearing spacecraft simulator controlled by four reaction wheels in a pyramidal arrangement. Tests were performed to determine the effectiveness of the two adaptive control theories under nominal operating conditions, a “plug-and-play” spacecraft scenario, and under simulated actuator damage. Proof of concept of the adaptive control theories applied to attitude …

Control Law Design And Validation For A Helicopter In-Flight Simulator, Brian T. Fujizawa

Master's Theses

In-flight simulation allows one aircraft to simulate the dynamic response of another aircraft. A control system designed to give RASCAL, a JUH-60A Black Hawk helicopter based at Moffett Field, CA, in-flight simulation capabilities has been designed, optimized and validated in this research. A classical explicit model following control system with a frequency dependent feedback controller was used. The frequency dependent controller allows model following of the attitude in the short term and the velocity in the long term. Controller gains were optimized using a high order, linearized model of UH-60 dynamics. Non-linear simulations of the control laws were performed, first …

Efficient Tether Dynamic Model Formulation Using Recursive Rigid-Body Dynamics, Brad Hembree, Nathan Slegers

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

A computationally efficient discrete model for low-strain tethers used in many engineering applications is developed without the use of elastic elements. The tether is modelled using N links, with each link treated as a body of revolution where it is assumed the tether spin is negligible to the dynamics, resulting in each link having only two degrees of freedom. A recursive algorithm is developed for the dynamic equations, with the solution procedure being an order N method requiring only a 2 x 2 matrix inversion, resulting in approximately half the computations of the general recursive algorithm. A comparison between the …

Effects Of Canopy-Payload Relative Motion On Control Of Autonomous Parafoils, Nathan Slegers

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

An 8 degree-of-freedom model is developed that accurately models relative pitching and yawing motion of a payload with respect to a parafoil. Constraint forces and moments are found analytically rather than using artificial constraint stabilization. A turn rate controller common in precision placement algorithms is used to demonstrate that relative yawing motion of the payload can result in persistent oscillations of the system. A model neglecting relative payload yawing failed to predict the same oscillations. It is shown that persistent oscillations can be eliminated by reduction of feedback gains; however, resulting tracking performance is poor. A reduced order linear model …

Fusion Of Imprecise Qualitative Information, Florentin Smarandache, Xinde Li, Xianzhong Dai, Jean Dezert

Branch Mathematics and Statistics Faculty and Staff Publications

In this paper, we present a new 2-tuple linguistic representation model, i.e. Distribution Function Model (DFM), for combining imprecise qualitative information using fusion rules drawn from Dezert-Smarandache Theory (DSmT) framework. Such new approach allows to preserve the precision and efficiency of the combination of linguistic information in the case of either equidistant or unbalanced label model. Some basic operators on imprecise 2-tuple labels are presented together with their extensions for imprecise 2-tuple labels. We also give simple examples to show how precise and imprecise qualitative information can be combined for reasoning under uncertainty. It is concluded that DSmT can deal …

Avoiding Overrun Accidents On Contaminated Runways, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Avoiding Aircraft Icing Accidents, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Precision Navigation Using Pre-Georegistered Map Data, Frederick C. Webber

Theses and Dissertations

Navigation performance in small unmanned aerial vehicles (UAVs) is adversely affected by limitations in current sensor technology for small, lightweight sensors. Because most UAVs are equipped with cameras for mission-related purposes, it is advantageous to utilize the camera to improve the navigation solution. This research improves navigation by matching camera images to a priori georegistered image data and combining this update with existing image-aided navigation technology. The georegistration matching is done by projecting the images into the same plane, extracting features using the techniques Scale Invariant Feature Transform (SIFT) [5] and Speeded-Up Robust Features (SURF) [3]. The features are matched …

Alternative Methods To Standby Gain Scheduling Following Air Data System Failure, Matthew W. Coldsnow

Theses and Dissertations

The United States Air Force has advanced fighter aircraft that lose the ability to operate in a large portion of their operating flight envelope when an air data system failure is experienced. These aircraft are reverted to a fixed set of standby-gains that limit their maneuverability, degrade handling qualities, and increase susceptibility to departure. The purpose of this research was to determine if three alternative methods of standby-gain-scheduling could provide robust control with minimal performance degradation despite the lack of air data. To accomplish this, three methods of standby-gain-scheduling were developed, integrated, and tested in the Infinity Cube simulator at …

Avoiding Veer-Off Accidents On Contaminated Runways, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

The Navigation Potential Of Ground Feature Tracking, Guner Mutlu

Theses and Dissertations

This research effort examines the reduction of error in inertial navigation aided by vision. This is part of an effort focused on navigation in a GPS denied environment. The navigation concept examined here consists of two main steps. First, extract the position of a tracked ground object using vision and geo-locate it in 3 dimensional navigation frame. In this first step multiple positions of the UAV are assumed known; think of a synthetic aperture. The only information about the tracked ground objects/features is the unit vector that points to the objects from the center of the camera. Two such vectors …

On-Board Orbit Determination And 3-Axis Attitude Determination For Picosatellite Applications, John Arthur Bowen

Master's Theses

This thesis outlines an orbit determination and 3-axis attitude determination system for use on orbit as applicable to 1U CubeSats and other picosatellites. The constraints imposed by the CubeSat form factor led to the need for a simple configuration and relaxed accuracy requirements. To design a system within the tight mass, volume, and power constraints inherent to CubeSats, a balance between hardware complexity, software complexity and accuracy is sought. The proposed solution consists of a simple orbit propagator, magnetometers with a magnetic field look-up table, Sun sensors with an analytic Sun direction model, and the TRIAD method to combine vector …

Satellite Formation Flight Navigation Using The Clohessy-Wiltshire Equations, Anna Kimmich

Aerospace Engineering

This report presents the design and simulation of a satellite navigation program using Matlab. The program allows any number of independent satellites to navigate in a co-planar cluster formation in a circular orbit with no input besides its location coordinates from a simulated GPS unit and the relative location of other satellites from a simulated on-board sensor. This navigation program uses a potential field-like function to calculate the desired satellite position within the formation. It uses the Clohessy-Wiltshire equations to calculate the impulsive maneuvers needed to achieve and maintain the formation.

Attitude Determination Of A Student Satellite Using On-Orbit Magnetometer And Temperature Data, Jacob Daniel Dimiceli

Master's Theses

An extended Kalman filter is modified to support only magnetometer data as a measurement for spacecraft attitude information. Actual on-orbit data from a student satellite is used in the filter from three different time periods and varying data frequencies. The extended Kalman filter has a thermal model that utilizes external temperature data as a verification tool for filter convergence and for parameter tuning. It can capture the frequency of temperature changes and the correct side panel being lit by the sun as long as the filter converges properly, but not the magnitude of the temperature at a specific time. A …

Validation Of Linearized Flight Models Using Automated System-Identification, Keith Eric Rothman

Master's Theses

Optimization based flight control design tools depend on automatic linearization tools, such as Simulink®’s LINMOD, to extract linear models. In order to ensure the usefulness and correctness of the generated linear model, this linearization must be accurate. So a method of independently verifying the linearized model is needed. This thesis covers the automation of a system identification tool, CIFER®, for use as a verification tool integrated with CONDUIT®, an optimization based design tool. Several test cases are built up to demonstrate the accuracy of the verification tool with respect to analytical results and matches with LINMOD. Several common nonlinearities are …

A Flight Simulation Study Of The Simultaneous Non-Interfering Aircraft Approach, Brian H. Reel

Master's Theses

Using a new implementation of a NASA flight simulation of the Quiet Short-Haul Research Aircraft, autopilots were designed to be capable of flying both straight in (ILS) approaches, and circling (SNI) approaches. A standard glideslope coupler was sufficient for most conditions, but a standard Proportional-Integral-Derivative (PID) based localizer tracker was not sufficient for maintaining a lateral track on the SNI course. To track the SNI course, a feed-forward system, using GPS steering provided much better results.

NASA and the FAA embrace the concept of a Simultaneous, Non-Interfering (SNI) approach as a way to increase airport throughput while reducing the noise …

Comparison And Design Of Simplified General Perturbation Models (Sgp4) And Code For Nasa Johnson Space Center, Orbital Debris Program Office, Nicholas Z. Miura

Master's Theses

This graduate project compares legacy simplified general perturbation model (SGP4) code developed by NASA Johnson Space Center, Orbital Debris Program Office, to a recent public release of SGP4 code by David Vallado. The legacy code is a subroutine in a larger program named PREDICT, which is used to predict the location of orbital debris in GEO. Direct comparison of the codes showed that the new code yields better results for GEO objects, which are more accurate by orders of magnitude (error in meters rather than kilometers). The public release of SGP4 also provides effective results for LEO and MEO objects …

Design And Control Considerations For A Skid-To-Turn Unmanned Aerial Vehicle, Tanner Austin Sims

Master's Theses

The use of Unmanned Aerial Vehicles (UAVs) are rapidly expanding and taking on new roles in the military. In the area of training and targeting vehicles, control systems are expanding the functionality of UAVs beyond their initially designed purpose. Aeromech Engineering’s NXT UAV is a high speed target drone that is intended to simulate a small aircraft threat. However, in the interest of increasing functionality, enabling NXT to accomplish wings level skidding turns provides the basis for a UAV that can simulate a threat from a missile. Research was conducted to investigate the aerodynamic and performance characteristics of a winged …

Design Of A "Figure-8" Spherical Motion Flapping Wing For Miniature Uav's, Zohaib Parvaiz Rehmat

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hummingbirds and some insects exhibit a Figure-8 motion, which allows them to undergo variety of maneuvers including hovering. It is therefore desirable to have flapping wing miniature air vehicles (FWMAV) that can replicate this unique wing motion. In this research, a design of a flapping wing for FWMAV that can mimic Figure-8 motion using a spherical four bar mechanism is presented. To produce Figure-8 motion, the wing is attached to the coupler point of the spherical four bar mechanism and driven by a DC servo motor. For verification of the design, a prototype of the wing and mechanism is fabricated …

Turn Constrained Path Planning Problems, Victor M. Roman

UNLV Theses, Dissertations, Professional Papers, and Capstones

We consider the problem of constructing multiple disjoint paths connecting a source point s to a target point t in a geometric graph. We require that the paths do not have any sharp turn angles. We present a review of turn constrained path planning algorithms and also algorithms for constructing disjoint paths. We then combine these techniques and present an O(nlogn) time algorithm for constructing a pair of edge disjoint turn constrained paths connecting two nodes in a planar geometric graph. We also consider the development of a turn constrained shortest path map in the presence of …

Aircraft Landing Operations On Contaminated Runways, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Modeling And Simulation Architecture For Studying Doppler-Based Radar With Complex Environments, Nicholas J. Amato

Theses and Dissertations

This research effort develops a hybrid large-scale modeling and simulation frame- work that defines the requirements for a program to evaluate radar-aircraft-turbine- clutter interactions. Wind turbines and other moving structures can interfere with a radar’s ability to detect moving aircraft because radar returns from turbines are comparable to those from slow flying aircraft. This interference can lead to aircraft collisions or crashes, reducing the safety for air traffic. Two radar applications, INSSITE and IMOM, were investigated to determine which of the subsystems, in the proposed architecture, are currently available and which need additional development. Current radar applications either delve too …

Performance Enhancements Of Ranging Radio Aided Navigation, Patric J. Ernsberger

Theses and Dissertations

Determining the position of team members is always useful information, whether it is a team of firefighters fighting a blaze or combatants clearing a building in the field. This information becomes even more decisive for the people responsible for their safety. To accomplish this in areas denied Global Navigation Satellite System (GNSS), such as around buildings or in steep valleys, alternative methods must be used. Radio ranging systems have been a part of the navigation solution for years. They unfortunately have poor performance in certain areas, such as inside buildings, due to multipath and other errors. To improve the position …