Navigation, Guidance, Control and Dynamics Commons^™

System Integration And Validation Of The Cal Poly Spacecraft Attitude Dynamics Simulator Mk. Iv, Bricen S. Rigby

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project that seeks to enable the simulation and validation of sensors, actuators, and control logic related to spacecraft attitude control. The SADS platform rests atop a spher- ical air-bearing device which allows for nearly frictionless rotation in all three axes. The orientation of the platform is controlled by four reaction wheels arranged in a pyramidal configuration. Over the past few years, there have been significant updates to the reaction wheel subsystem, as well as requests for a more capable central com- puter. Therefore, a new system architecture for the …

Development Of A Computer Vision Based Rendezvous And Docking Test Platform, David T. Forbes

Master's Theses

This thesis presents the work completed in the development and testing of a low-cost modular sensor package capable of rendezvous and docking by providing a vehicle with relative navigational commands. These navigational commands are created using relative localization data gathered and processed onboard the sensor package, with validation, in post-processing, against global localization data. This research aims to reduce the cost of smaller autonomous vehicles by removing the need for custom control units, as its modular nature will allow it to be adapted to many different systems and vehicles. Discussed within this thesis is the rapid prototyping, development, and testing …

Development Of A Free-Floating Space Robotic Simulator, Truman: Terrestrial Robotic Unit For Multibody Analysis And Navigation, Jackson W. Cordova

Master's Theses

This work describes the development of a 3 Degree-of-Freedom (DOF) robotic manipulator for use on a free-floating planar air-bearing vehicle. The system developed aims to serve as a foundation for future space robotics research at the California Polytechnic State University (Cal Poly)’s Space Robotics Laboratory. Systems doc- umentation describes conceptual operation and architecture of the proposed system: Terrestrial Robotic Unit for Multibody Analysis and Navigation (TRUMAN). The key operation of TRUMAN is to study a self launch maneuver of a free-floating ve- hicle including 4 distinct phases: launch off a fixed rail, coast, reorientation using manipulator motion, and capture of …

Spaceotter: A Floating Spacecraft Simulator Air Bearing Vehicle For Hardware-In-The-Loop Experiments And Research, Alexander Debartolo

Master's Theses

Growing interest in nanosatellites has increased demand for accessible ground-testing methods, which have historically been expensive and restricted. Floating Spacecraft Simulators (FSS), built around Air Bearing Vehicles (ABVs), address this gap by approximating a zero-gravity, friction-minimized environment suitable for testing spacecraft control systems, robotics, and propulsion on the ground.

This thesis presents the design, realization, and initial performance characterization of the Space Optically Tracked Testbed for Experiments and Research (SpaceOTTER) ABV, developed for the Cal Poly Space Robotics Lab. SpaceOTTER is the first step toward emulating the 3 degree of freedom (3-DOF) planar dynamics of a simulated spacecraft and is …

Hamster: Hybrid-Actuated Mobile Spherical Terrain Exploration Rover, Winnie Gao

Master's Theses

The expansion of space exploration to increasingly challenging planetary environments requires mobility systems capable of extreme traversal capabilities and operational reliability. This thesis presents the design, development, and testing of a low-cost Hybrid-Actuated Mobile Spherical Terrain Exploration Rover (HAMSTER) intended for use on a planetary surface exploration mission. HAMSTER uses a pendulum-based actuation method for steering and an actuated internal shaft to propel the vehicle forward. The internal structure includes a two-tiered central case composed of the navigation control module, accelerometer, motor controller, primary DC motor, battery, voltage regulators, Raspberry Pi, pendulum servo motor, and drive shafts. Additive manufacturing through …

Design And Implementation Of An Embedded Control System For The Cal Poly Spacecraft Attitude Dynamics Simulator, Neil Mahesh Bedagkar

Master's Theses

This thesis presents the development of a cascaded reaction wheel control system for Cal Poly's Spacecraft Attitude Dynamics Simulator. This work considers system architecture, empirical modeling, high-fidelity simulation, embedded firmware, hardware integration, and experimental characterization. In discrete-time simulation, it is shown that nonlinear direct model reference adaptive control (NDMRAC) enables a nonlinear, partially known plant with realistic actuator dynamics to track the response of a canonical second-order transfer function, with settling time within 4.67% and percent overshoot within order of magnitude of the second-order response. In hardware, the feasibility of a cascaded reaction wheel control architecture is experimentally demonstrated, achieving …

Development And Test Of An Automatic Mass Balancing System For Cal Poly's Spacecraft Attitude Dynamics Simulator, Cameron B. Zorio

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project to develop an air-bearing platform capable of recreating on-orbit rotational dynamics with near frictionless and torque-free rotations. However, any offset between the platform's center of rotation and its center of mass will introduce a torque due to gravity.

This thesis presents the design, implementation, and experimental evaluation of a low-cost, automatic mass balancing system for the SADS to address this challenge. A new modular sliding mass system was developed that overcomes issues faced in previous iterations of the SADS, providing real-time positional control of the masses and a …

Sparse-Data Orbit Estimation In Low Earth Orbit Using The Markov Chain Monte Carlo Ensemble Gaussian Mixture Filter, Nicholas J. Oden

Master's Theses

The number of space objects (SOs) in low Earth orbit (LEO) continues to increase rapidly, creating challenges for the current ground-based tracking network, which cannot accommodate the projected growth in SOs. Catalog maintenance relies on frequent observations for reliable reacquisition, with Two-Line Element (TLE) sets typically generated daily to mitigate rapid error growth from poor TLE accuracy. This constraint limits the ability to track more objects with existing infrastructure. This work evaluates the Markov Chain Monte Carlo Ensemble Gaussian Mixture Filter (MCMC EnGMF), a nonlinear, non-Gaussian filter well-suited for sparse tracking scenarios where higher post-update accuracy is needed to reduce …

Design And Development Of A Laboratory Star Tracker System, Kevin D. Iverson

Master's Theses

This thesis presents the design, calibration, and validation of a low-cost star tracker system and hardware-in-the-loop testbed intended for small satellite applications. The system is composed entirely of commercial off-the-shelf components and integrates both a custom star tracker and a screen-based star field simulator for controlled, repeatable testing. An analytical modeling approach was used in the early design phase to predict system accuracy based on key optical and geometric parameters, informing the selection and configuration of components and guiding the development of calibration routines.

A simulation environment was developed to validate the star tracker software and assess the impact of …

Hardware-In-The-Loop Testing For The Polysim Adcs Lab, Shealyn P. Miller

Master's Theses

Hardware-in-the-loop, HIL, testing is an important tool for the validation and verification of systems in the aerospace industry. A common subsystem to be tested using HIL testing is the attitude, dynamics, and controls subsystem, ADCS. This is due to HIL tests using realistic simulations of the space environment to control physical hardware. To create a HIL test, a simulation and HIL interface are needed to test and communicate with hardware. Using a Speedgoat Performance Real-Time Target Machine to communicate with a Raspberry Pi and a Simulink model, three tests were conducted to ensure communication was functioning properly. A simulation, in …

Development Of A Reaction Wheel System For Cal Poly’S Spacecraft Attitude Dynamics Simulator, Caleb Nalley

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project to develop a system capable of simulating the attitude dynamics and kinematics of a rigid body in space. Actuations on the SADS are performed by reaction wheels, however the current reaction wheels have various issues that decrease system performance and are not independent of the SADS. The reaction wheel developed as part of this thesis will be designed to improve performance and set out design specifications tailored to the SADS, serve as an independent assembly that can be transferred to other systems, and provide a general outline for …

An Investigation Into The Use Of Amateur Astronomy Equipment For Optical Orbit Determination Using A Mobile Telescope Platform, Johan C. Govaars

Master's Theses

The process of optical orbit determination has long been in the domain of large organizations and stationary observatories with highly specialized scientific equipment. This thesis seeks to determine not only if satellites can be captured regularly using purely commercial-off-the-shelf (COTS) equipment, but also if initial orbit determinations can be made using that data. Moreover, the use of a mobile telescope platform allows users to circumvent the restrictions of fixed observatories such as low horizon viewing restrictions or existing light pollution.

A completely COTS setup was utilized that included an 8-inch Celestron NextStar 8SE telescope with an f/6.3 focal reducer and …

Automatic Mass Balancing Of A Spacecraft Attitude Dynamics Simulator With Six Sliding Masses, Amelia J. Gilman

Master's Theses

The goal of this thesis is to investigate automatic mass balancing methods for spacecraft attitude dynamics simulators, create a hardware design for a mass balancing system, and assemble the hardware on the Cal Poly Spacecraft Attitude Dynamics Simulator (SADS). Spacecraft attitude dynamics simulators replicate the torque-free environment of space with ground-based hardware. The SADS is mounted on a spherical air bearing, and includes a pyramid of four reaction wheels. The air bearing allows frictionless, unbounded rotation about the vertical axis, and 30 degrees about the horizontal axes. The torque-free configuration of the SADS can be used to test spacecraft attitude …

Exploring The Feasibility Of The Resonance Corridor Method For Post Mission Disposal Of High-Leo Constellations, Payton G. Porter

Master's Theses

In the upcoming decade, the proliferation of high-LEO constellations is expected to exceed 20,000 objects, yet comprehensive Post Mission Disposal (PMD) strategies for these constellations are currently lacking. With the inherent challenges of efficiently deorbiting satellites from High-LEO orbits, there arises an urgent need to explore innovative approaches. Building upon insights garnered from the ReDSHIFT project and anticipating the proliferation of high-LEO constellations such as OneWeb, TeleSat, and GuoWang, this thesis delves into the potential viability of the Resonance Corridor Method for PMD. The investigation encompasses key metrics, including deorbit timelines and $\Delta v$ requirements to meet regulatory standards or …

A Hardware-In-The-Loop Star Tracker Test Bed, Ashley Haraguchi

Master's Theses

As the use of small satellites for advanced space missions continues to grow, the importance of low mass and cost three-axis attitude stabilization systems increases as well, with these systems requiring high accuracy attitude knowledge. Star trackers provide the most accurate attitude knowledge of any type of attitude sensor, but the high cost, size, and weight of commercial star trackers can be prohibitive to small satellite missions. Many simple star trackers have been developed using commercial off-the-shelf camera sensors and processing hardware, but the challenge remains in testing and characterizing these devices. A common solution is night sky tests, in …

Gyroless Nanosatellite Attitude Determination Using An Array Of Spatially Distributed Accelerometers, Kory J. Haydon

Master's Theses

The low size and budget of typical nanosatellite missions limit the available sensors for attitude estimation. Relatively high noise MEMS gyroscopes often must be employed when accurate knowledge of the spacecraft’s angular velocity is necessary for attitude determination and control. This thesis derived and tested in simulation the “Virtual Gyroscope” algorithm, which replaced a standard gyroscope with an array of spatially distributed accelerometers for a 1U CubeSat mission. A MEMS accelerometer model was developed and validated using Root Allan Variance, and the Virtual Gyroscope was tested both in the open loop configuration and as a replacement for a gyroscope in …

Autonomous Attitude Consensus For Nanosatellite Formations In Leo, Laird J. Mendelson

Master's Theses

Consensus strategies are examined as a possible approach to achieving attitude alignment for a large, close-proximity formation of nanosatellites in low earth orbit (LEO). An attitude-only distributed consensus approach is selected for further consideration due to its comparatively low data transmission requirements. The convergence of a connected network of satellites to the attitude agreement subspace under this control law is shown using a Lyapunov stability approach with a set of idealizing assumptions. A moderate-fidelity simulation demonstrates the performance of the control law under realistic conditions that violate those assumptions. Particular emphasis is placed on the conditions that arise from the …

Distributed Control Of Servicing Satellite Fleet Using Horizon Simulation Framework, Scott Plantenga

Master's Theses

On-orbit satellite servicing is critical to maximizing space utilization and sustainability and is of growing interest for commercial, civil, and defense applications. Reliance on astronauts or anchored robotic arms for the servicing of next-generation large, complex space structures operating beyond Low Earth Orbit is impractical. Substantial literature has investigated the mission design and analysis of robotic servicing missions that utilize a single servicing satellite to approach and service a single target satellite. This motivates the present research to investigate a fleet of servicing satellites performing several operations for a large, central space structure.

This research leverages a distributed control approach, …

Developing A Light Curve Simulation Tool For Ground And Space-Based Observations Of Spacecraft And Debris, Andrew T. Ochoa

Master's Theses

A light curve is a plot of brightness versus time of an object. Light curves are dependent on orbit, attitude, surface area, size, and shape of the observed object. Using light curve data, several analysis methods have been developed to derive these parameters. These parameters can be used for tracking orbital debris, monitoring satellite health, and determining the mission of an unknown spacecraft.

This paper discusses the development, verification, and utilization of a tool that simulates light curve data. This tool models ground-based observations, space-based observations, self-shadowing geometry, tumbling debris, and controlled spacecraft. The main output from the tool is …

Interior Point Optimization Of Low-Thrust Spacecraft Trajectories, Jordan D. Frederiksen

Master's Theses

Low-thrust interplanetary spacecraft trajectory optimization poses a uniquely difficult problem to solve because of the inherent nonlinearities of the dynamics and constraints as well as the large size of the search space of possible solutions. Tools currently exist that optimize low-thrust interplanetary trajectories, but these tools are rarely openly available to the public, and when they are available they require multiple interfaces between multiple different packages. The goal of this work is to present a new piece of low-thrust interplanetary spacecraft trajectory optimization software that is open-source and entirely self-contained so that more people can have access to the ability …

Simulation Of A Configurable Hybrid Aircraft, Brandon Bartlett

Master's Theses

As the demand for air transportation is projected to increase, the environmental impacts produced by air travel will also increase. In order to counter the environmental impacts while also meeting the demand for air travel, there are goals and research initiatives that aim to develop more efficient aircraft. An emerging technology that supports these goals is the application of hybrid propulsion to aircraft, but there is a challenge in effectively exploring the performance of hybrid aircraft due to the time and money required for safe flight testing and due to the diverse design space of hybrid architectures and components. Therefore, …

Passive Disposal Of Launch Vehicle Stages In Geostationary Transfer Orbits Leveraging Small Satellite Technologies, Marc Alexander Galles

Master's Theses

Once a satellite has completed its operational period, it must be removed responsibly in order to reduce the risk of impacting other missions. Geostationary Transfer Orbits (GTOs) offer unique challenges when considering disposal of spacecraft, as high eccentricity and orbital energy give rise to unique challenges for spacecraft designers. By leveraging small satellite research and integration techniques, a deployable drag sail module was analyzed that can shorten the expected orbit time of launch vehicle stages in GTO. A tool was developed to efficiently model spacecraft trajectories over long periods of time, which allowed for analysis of an object’s expected lifetime …

Low-Cost Reaction Wheel Design For Cubesat Applications, Nicholas J. Bonafede Jr.

Master's Theses

As science instruments on CubeSats become more sensitive to the attitude of the spacecraft, better methods must be employed to provide the accuracy needed to complete the planned mission. While systems that provide the accuracy required are available commercially, these solutions are not cost-effective, do not allow the design to be tailored to a specific mission, and most importantly, do not give students hand-on experience with attitude control actuators. This thesis documents the design, modeling, and simulation of a low-cost, student-fabricated, reaction wheel system for use in 3U CubeSat satellites. The entire design process for the development of this reaction …

Three Axis Attitude Control System Design And Analysis Tool Development For The Cal Poly Cubesat Laboratory, Liam T. Bruno

Master's Theses

The Cal Poly CubeSat Laboratory (CPCL) is currently facing unprecedented engineering challenges—both technically and programmatically—due to the increasing cost and complexity of CubeSat flight missions. In responding to recent RFPs, the CPCL has been forced to find commercially available solutions to entire mission critical spacecraft subsystems such as propulsion and attitude determination & control, because currently no in-house options exist for consideration. The commercially available solutions for these subsystems are often extremely expensive and sometimes provide excessively good performance with respect to mission requirements. Furthermore, use of entire commercial subsystems detracts from the hands-on learning objectives of the CPCL by …

Conceptual Design Of A South Pole Carrier Pigeon Uav, Kendrick M. Dlima

Master's Theses

Currently, the South Pole has a large data problem. It is estimated that 1.2 TB of data is being produced every day, but less than 500 GB of that data is being uploaded via aging satellites to researchers in other parts of the world. This requires those at the South Pole to analyze the data and carefully select the parts to send, possibly missing out on vital scientific information. The South Pole Carrier Pigeon will look to bridge this data gap.

The Carrier Pigeon will be a small unmanned aerial vehicle that will carry a 30 TB solid-state hard drive …

Navigational Feasibility Of Flyby / Impact Missions To Interstellar Objects, Declan Moore Mages

Master's Theses

In October 2017, the first interstellar object, designated 1I/2017 U1 and more commonly referred to as Oumuamua, was detected passing through our solar system by the Pan-STARRS telescope, followed recently by the detection of 2I/Borisov in August 2019. These detections came much sooner than thought possible, and have redefined our understanding of the population of interstellar objects. With the construction of the next generation of powerful observatories, future detections are estimated to occur as frequently as two per year, and while there is significant scientific understanding to be gained from observing these objects remotely, a spacecraft sent to intercept one …

Generating Exploration Mission-3 Trajectories To A 9:2 Nrho Using Machine Learning, Esteban Guzman

Master's Theses

The purpose of this thesis is to design a machine learning algorithm platform that provides expanded knowledge of mission availability through a launch season by improving trajectory resolution and introducing launch mission forecasting. The specific scenario addressed in this paper is one in which data is provided for four deterministic translational maneuvers through a mission to a Near Rectilinear Halo Orbit (NRHO) with a 9:2 synodic frequency. Current launch availability knowledge under NASA’s Orion Orbit Performance Team is established by altering optimization variables associated to given reference launch epochs. This current method can be an abstract task and relies on …

Orbital Constellation Design And Analysis Using Spherical Trigonometry And Genetic Algorithms: A Mission Level Design Tool For Single Point Coverage On Any Planet, Joseph R. Gagliano

Master's Theses

Recent interest surrounding large scale satellite constellations has increased analysis efforts to create the most efficient designs. Multiple studies have successfully optimized constellation patterns using equations of motion propagation methods and genetic algorithms to arrive at optimal solutions. However, these approaches are computationally expensive for large scale constellations, making them impractical for quick iterative design analysis. Therefore, a minimalist algorithm and efficient computational method could be used to improve solution times. This thesis will provide a tool for single target constellation optimization using spherical trigonometry propagation, and an evolutionary genetic algorithm based on a multi-objective optimization function. Each constellation will …

Determining Feasibility Of A Propulsionless Microsatellite Formation Flight Mission, Aaron Levis

Master's Theses

Benefits of developing missions with multiple formation flying spacecraft as an alternative to a traditional monolithic vehicle are becoming apparent. In some cases, these missions can lower cost and increase flexibility among other situational advantages. However, there are various limitations that are imposed by these missions that are centered on the concept of maintaining the necessary formation. One such limitation is that of the propulsion system required for each spacecraft. To mitigate the complexity and mass of the onboard propulsion, the pairing of electromagnetic actuators and differential drag to replace the functionality of a propulsive system is investigated. By using …

Modeling And Simulation Of A Sounding Rocket Active Stabilization System, Steven M. Maclean

Master's Theses

The Horizon Simulation Framework is a modeling and simulation framework developed to verify system level requirements. In this thesis, the framework is extended to include the Dynamic position type that existed in the early development phase of the framework. The Dynamic position type is tested through the modeling and simulation of a sounding rocket. An active control system based on linear-quadratic regulator (LQR) control theory is implemented and tested in the simulation to determine the overall effect on altitude. A first order aerodynamics and aeroprediction model are created within the framework to allow for rapid changes early in the design …