Navigation, Guidance, Control and Dynamics Commons^™

Cubesat Reaction Wheel Attitude Control Platform System Architecture, Justin Hartland

Beyond: Undergraduate Research Journal

In the classroom, physics behind spacecraft attitude dynamics and controls is abstract and difficult to comprehend. It is common that students struggle to develop the connection between the math they learn and how it can be applied in the real world. The goal of this project is to design and manufacture a 1U, 3U, and 6U CubeSat testbed for autonomous control systems utilizing reaction wheels. The testbed will include three separate reaction wheels each mounted on its own respective axis to control the attitude in 3 degrees of freedom. The end goal of the CubeSat Control Platform is to be …

Increasing The Reliability Of Software Systems On Small Satellites Using Software-Based Simulation Of The Embedded System, Matthew D. Grubb

Graduate Theses, Dissertations, and Problem Reports (ETD)

The utility of Small Satellites (SmallSats) for technology demonstrations and scientific research has been proven over the past few decades by governments, universities, and private companies. While the research and technology demonstration objectives that can be provided by these SmallSats are becoming similar to larger spacecraft, their reliability still falls behind. This is in part due to the reduced cost of SmallSat missions in comparison to large spacecraft, which requires cheaper components, rapid development schedules, and accepted risk. In these missions, the importance of the flight software is often overlooked, and the software is rushed through development and not fully …

Low-Cost Reaction Wheel Design For Cubesat Applications, Nicholas J. Bonafede Jr.

Master's Theses

As science instruments on CubeSats become more sensitive to the attitude of the spacecraft, better methods must be employed to provide the accuracy needed to complete the planned mission. While systems that provide the accuracy required are available commercially, these solutions are not cost-effective, do not allow the design to be tailored to a specific mission, and most importantly, do not give students hand-on experience with attitude control actuators. This thesis documents the design, modeling, and simulation of a low-cost, student-fabricated, reaction wheel system for use in 3U CubeSat satellites. The entire design process for the development of this reaction …

Determining Feasibility Of A Propulsionless Microsatellite Formation Flight Mission, Aaron Levis

Master's Theses

Benefits of developing missions with multiple formation flying spacecraft as an alternative to a traditional monolithic vehicle are becoming apparent. In some cases, these missions can lower cost and increase flexibility among other situational advantages. However, there are various limitations that are imposed by these missions that are centered on the concept of maintaining the necessary formation. One such limitation is that of the propulsion system required for each spacecraft. To mitigate the complexity and mass of the onboard propulsion, the pairing of electromagnetic actuators and differential drag to replace the functionality of a propulsive system is investigated. By using …

Active Permanent Magnet Attitude Control For Cubesats Using Mu-Metal Shielding, Maxwell Martin

Mechanical Engineering Undergraduate Honors Theses

Cube-Satellites (CubeSats) are nanosatellites composed of cube shaped units, each nominally 10cm to a side and around 1kg in mass. Due to their inherent size and weight limitations, it is often impractical to use conventional attitude, or rotational, control methods such as thrusters on these small satellites. Several methods, including magnetorquer rods and small reaction wheels, are often used instead of traditional methods to work around the size and weight limitations. As a new alternative to these methods, a permanent magnet mounted on a rotatable shaft could be used to achieve attitude control. In much the same way that a …

Polysat Helmholtz Cage, Alex Nichols, Nicolas Le Renard, Jordan Skaro, Louie Thiros, Madeline Tran

Mechanical Engineering

The MagCal5 Helmholtz cage project is an interdisciplinary approach to provide the PolySat/CubeSat research lab with a magnetic testing environment for the calibration of magnetic components and verification of various control laws. The Cal Poly CubeSat organization is the home of the CubeSat Specification, and acts as a testing and integration facility for CubeSats built by universities across the world. The PolySat organization is a CubeSat developer that works with numerous industry partners to design, manufacture, and operate CubeSats to further scientific advancement. The addition of a magnetic test stand to the lab will allow CubeSat to extend to the …

Evaluation Of Verification Approaches Applied To A Nonlinear Control System, Kerianne H. Gross

Theses and Dissertations

As the demand for increasingly complex and autonomous systems grows, designers may consider computational and artificial intelligence methods for more advanced, re- active control. While the performance gained by such increasingly intelligent systems may be superior to traditional control techniques, the lack of transparency in the systems and opportunity for emergent behavior limits their application in the field. New verification and validation methods must be developed to ensure the output of such controllers do not put the system or any people interacting with it in danger. This challenge was highlighted by the former Air Force Chief Scientist in his 2010 …

Attitude Determination & Control System Design And Implementation For A 6u Cubesat Proximity Operations Mission, Francisco J. Franquiz

Doctoral Dissertations and Master's Theses

The purpose of this work is to discuss the attitude determination and control system (ADCS) design process and implementation for a 12 kg, 6U (36.6 cm x 23.9 cm x 27.97 cm) CubeSat class nano-satellite. The design is based on the requirements and capabilities of the Application for Resident Space Object Proximity Analysis and IMAging (ARAPAIMA) proximity operations mission. The satellite is equipped with a cold gas propulsion system capable of exerting 2.5 mN m torques in both directions about each body axis. The attitude sensors include an angular rate gyro and star tracker (STR), supplemented by the payload optical …

A Gravity Gradient, Momentum-Biased Attitude Control System For A Cubesat, Ryan J. Sellers

Master's Theses

ExoCube is the latest National Science Foundation (NSF) funded space weather CubeSat and is a collaboration between PolySat, Scientific Solutions Inc. (SSI), the University of Wisconsin, NASA Goddard and SRI International. The 3U will carry a mass spectrometer sensor suite, EXOS, in to low earth orbit (LEO) to measure neutral and ionized particles in the exosphere and thermosphere. Measurements of neutral and ion particles are directly impacted by the angle at which they enter EXOS and which leads to pointing requirements. A combination of a gravity gradient system with a momentum bias wheel is proposed to meet pointing requirements while …

An Attitude Determination System With Mems Gyroscope Drift Compensation For Small Satellites, Maxwell Bezold

Theses and Dissertations--Electrical and Computer Engineering

This thesis presents the design of an attitude determination system for small satellites that automatically corrects for attitude drift. Existing attitude determination systems suffer from attitude drift due to the integration of noisy rate gyro sensors used to measure the change in attitude. This attitude drift leads to a gradual loss in attitude knowledge, as error between the estimated attitude and the actual attitude increases.

In this thesis a Kalman filter is used to complete sensor fusion which combines sensor observations with a projected attitude based on the dynamics of the satellite. The system proposed in this thesis also utilizes …

An Analysis Of Stabilizing 3u Cubesats Using Gravity Gradient Techniques And A Low Power Reaction Wheel, Erich Bender

Aerospace Engineering

The purpose of this paper is to determine the feasibility of gravity gradient stabilizing a 3U CubeSat and then using a miniature reaction wheel to further increase stability characteristics. This paper also serves as a guide to understanding and utilizing quaternions in attitude control analysis. The analytical results show that using 33 centimeter booms and 400 gram tip masses, a 3U CubeSat will experience a maximum of 6 degrees of angular displacement in yaw and pitch, and less than .5 degrees of angular displacement in the nadir axis. A .120 kilogram miniature reaction wheel developed by Sinclair Interplanetary was introduced …

Boom Stability Control Final Project Report, Michael Barnes, Justin Carnahan, Daniel Fluitt, Alicia Johnstone

Mechanical Engineering

The BOOMStiC Gravity Gradient Boom and Turnstile Antenna project was developed to provide a passive attitude control system and better communications for future CubeSat satellites developed by California Polytechnic State University. The system utilizes the energy from a coilable metal spring to deploy a tip mass to a length of one meter from the side of the satellite. Calculations show the resulting gravity gradient torque causes to the satellite to settle two degrees from normal to the earth’s surface.

On-Board Orbit Determination And 3-Axis Attitude Determination For Picosatellite Applications, John Arthur Bowen

Master's Theses

This thesis outlines an orbit determination and 3-axis attitude determination system for use on orbit as applicable to 1U CubeSats and other picosatellites. The constraints imposed by the CubeSat form factor led to the need for a simple configuration and relaxed accuracy requirements. To design a system within the tight mass, volume, and power constraints inherent to CubeSats, a balance between hardware complexity, software complexity and accuracy is sought. The proposed solution consists of a simple orbit propagator, magnetometers with a magnetic field look-up table, Sun sensors with an analytic Sun direction model, and the TRIAD method to combine vector …