Navigation, Guidance, Control and Dynamics Commons^™

Design Of Synthetic Jet Actuator For Flight Control Of Small Uav, Priyanka Pagadala

Doctoral Dissertations and Master's Theses

The main idea of this project is to develop a prototype SJA - Synthetic Jet Actuator to embed into a small UAV with modified Glauert wing cross-section for Active Flow Control. Apart from lift enhancement, drag reduction, or separation control, etc; LCO suppression might be possible by modifying the boundary layer through the use of these actuators. For initial investigation, a wing section with span of 12.4 cm and chord of 14 cm was fabricated and tests were conducted in the subsonic wind tunnel at the free stream velocities of 5 and 10 m / s. From these experiments, lift …

Fault-Injection Experiment For The Statistical Characterization Of Faults In Avionics Communication System, Amy M. Yates

Electrical & Computer Engineering Theses & Dissertations

Since flight control systems perform safety-critical functions, it is important to understand the possible effects on the closed-loop dynamical system's performance caused by these faults. The purpose of this project is to design the software and hardware needed to add fault-injection and monitoring capabilities to ROBUS-2, a flight communication system. ROBUS-2 is the current version of the fault-tolerant computer communication system used by the Scalable Processor-Independent Design for Enhanced Reliability (SPIDER), a general-purpose fault-tolerant integrated modular architecture (IMA) developed at the NASA Langley Research Center. The major components of SPIDER include processing elements (PEs) to perform calculations, bus interface units …

An Investigation Into The Feasibility Of Using A Modern Gravity Gradient Instrument For Passive Aircraft Navigation And Terrain Avoidance, Marshall M. Rogers

Theses and Dissertations

Recently, Gravity Gradient Instruments (GGIs) - devices which measure the spatial derivatives of gravity, have improved remarkably due to development of accelerometer technologies. Specialized GGIs are currently flown on aircraft for geological purposes in the mining industries. As such, gravity gradient data is recorded in flight and detailed gradient maps are created after post mission processing. These maps, if stored in a database onboard an aircraft and combined with a GGI, form the basis for a covert navigation system using a map matching process. This system is completely passive and essentially unjammable. To determine feasibility of this method, a GGI …

Multivariable Flight Control Design Tool Incorporating Gain And Phase Root Locus, Yong Ki Yoon

Mechanical & Aerospace Engineering Theses & Dissertations

A challenging problem in flight control system design for highly maneuverable aircraft is the coordinated control of the lateral-directional axes. Design goals are based on desired flying qualities giving an indication of whether the response to pilot inputs will be acceptable. Satisfying these closed-loop design objectives employing a computerized flight control system requires multiple feedback and crossfeed paths which operate in a well coordinated fashion. Contemporary control design tools, which close all loops simultaneously, have addressed this problem for several decades. Concerns associated with these strategies are the complicated mathematical relationships between the designer inputs and resulting closed-loop properties, and …

Development Of A Low-Latency, High Data Rate, Differential Gps Relative Positioning System For Uav Formation Flight Control, Stephen J. Comstock

Theses and Dissertations

In order for Unmanned Aerial Vehicles (UAVs) to be able to fly missions currently performed by manned aircraft, they must be able to conduct in-flight refueling. Additionally, significant fuel savings can be realized if multiple UAV's are able to fly in precise formation and align wingtip vortices. In either case, the precise relative position between the aircraft must be known to an accuracy of only a few centimeters. Previous research at the Air Force Institute of Technology culminated in the development of a relative positioning system for manned aircraft. This thesis presents the development of the next-generation system designed for …

Performance Analysis Of Recoverable Flight Control Systems Subject To Neutron-Induced Upsets Using Hybrid Dynamical Models, Hong Zhang

Electrical & Computer Engineering Theses & Dissertations

It has been observed that atmospheric neutrons can produce single-event upsets in digital flight control hardware. Potentially, they can reduce system performance and introduce a safety hazard. One experimental system-level approach investigated to help mitigate the effects of these upsets is NASA Langley's Recoverable Computer System. It employs rollback error recovery using dual-lock-step processors together with new fault tolerant architectures and communication subsystems.

In this dissertation, a class of stochastic hybrid dynamical models, which consists of a jump-linear system and a stochastic finite-state automaton, is used to describe the performance of a Boeing 737 aircraft system in closed-loop with a …

Formation Flight Control For Aerial Refueling, Steven M. Ross

Theses and Dissertations

A controller is designed for an aircraft to autonomously fly formation during aerial refueling. Requirements for a refueling autopilot are stated. A six-degree-of-freedom model is developed for an F-16 lead aircraft and a Learjet LJ-25 wing aircraft. Bare airframe stability of both aircraft is investigated, and stability augmentation is performed. A Matlab Simulink® simulation is built to reproduce the sensor inputs that will be available to the wing aircraft in flight, including disturbances. Control frames are investigated to determine the optimum presentation of the error vector for control during the task of air refueling. Control laws are developed from the …

Contemporary-Classical Sequential Loop Design With Parameter Uncertainty, Donghyuk Jeong

Mechanical & Aerospace Engineering Theses & Dissertations

Standard sequential loop closure design based on Evans root migration concepts is a well accepted, insightful and effective technique for meeting nominal performance objectives and traditional gain-phase stability margin requirements. Unfortunately, assessment of closed-loop variations resulting from parameter error is a post-process, implying an undesirable design-assess-redesign procedure is necessary if variations are found unacceptable. Further, the modem parameter uncertainty assessment framework is often inconsistent, both quantitatively and qualitatively, with the redesign task. Specifically, the parameter uncertainty assessment variables are not readily apparent in the sequential loop design framework, and these variables provide little guidance for the redesign strategy. Therefore, enhancing …

Nonlinear Regression Methods For Estimation, Eric B. Nelson

Theses and Dissertations

Regression techniques are developed for batch estimation and applied to three specific areas, namely, ballistic trajectory launch point estimation, adaptive flight control, and radio-frequency target triangulation. Specifically, linear regression with an intercept is considered in detail. An augmentation formulation is developed. Extensions of theory are applied to nonlinear regression as well. The intercept parameter estimate within the linear regression is used to identify the effects of trim change that are associated with the occurrence of a control surface failure. These estimates are used to adjust the inner loop control gains via a feed-forward command, hence providing an automatic reconfigurable retrim …

Characterization Of A Rotary Flat Tail As A Spoiler And Parametric Analysis Of Improving Directional Stability In A Portable Uav, Troy A. Leveron

Theses and Dissertations

The United States Air Force Research Lab, Munitions Directorate, Flight Vehicles, Integration Branch (AFRL/MNAV), has developed a flexible wing micro air vehicle (MAV) to be used with special tactics groups. In keeping with the requirement that this MAV be compact, previous research developed a rotatable tail mechanism which resulted in tail movement similar to that of a bird's tail. In this study the design of this tail was modified to produce a more storable vehicle. The redesign also allowed the tail to deflect upward to large angles, enabling the tail to be used as a spoiler. The aerodynamic effects of …

Full Capability Formation Flight Control, Ryan K. Osteroos

Theses and Dissertations

The subject of automatic formation flight control is of current interest to the development of Unmanned Aerial Vehicles (UAV). Previous control approaches have been refined in this work to allow more robust maneuvering and to include a fourth control parameter. The equations of motion for each aircraft as a point mass, expressed in a wind-axis coordinate system, are coupled into differential equations that model the two aircraft system dynamics. Control laws are developed that include proportional and integral action. Gains are determined based on formation performance. Lead maneuvers are simulated and the controller is gauged on its ability to maintain …

Outside Loop Control In Asymmetrical Trimmed Flight Conditions, Gary D. Miller

Theses and Dissertations

Traditionally flight control systems have used linearized equations of motion solved around a single trim point. This thesis proposes a nested-loop controller directly solved from the equations of motion. The control equations were developed as a solution to asymmetrically trimmed flight conditions. A two-loop design was proposed for the controller. The outer loop modeled the aircraft as a point mass and all forces were balanced to find the aircraft states. The equations input the control variables and output the aircraft states. The inner-loop utilizes the six-degree of freedom model of the aircraft to solve the moment equations. With the input …

A Comparison Of Nonlinear Algorithms To Prevent Pilot-Induced Oscillations Caused By Actuator Rate Limiting, James G. Hanley

Theses and Dissertations

The objective of this study was to compare the ability of the Feedback-with-Bypass (FWB) and the Derivative-Switching (DS) flight control system filters to prevent PIO during actuator rate limiting, and the filters' effects on aircraft handling qualities. This comparison was conducted in three steps: computer simulation, ground simulation in the Large Amplitude Multimode Aerospace Research Simulator (LAMARS), and flight tests conducted in the Variable Stability In-flight Simulator Test Aircraft (VISTA). During computer simulation, the FWB filter better reduced the phase lag and prevented sustained or divergent oscillations during the closed-loop analysis. During both ground simulation and flight tests, the FWB …

Analysis Of Error Recovery Effects On Digital Flight Control Systems, Arturo Tejada Ruiz

Electrical & Computer Engineering Theses & Dissertations

Life-critical, real-time applications like flight-by-wire aircraft, rely on closed-loop digital control systems and fault-tolerant computer systems to reliably achieve the desired operation. The computer systems, however, may be affected by random hardware/software faults induced mainly by environmental conditions such as high intensity radiated fields (HIRF) and lightning. These harsh electromagnetic environments are known to induce common­ mode faults (CMF) in aircraft electronic systems, which disrupt fault-tolerant provisions and possibly affect the operation of the digital control system. Current flight-by-wire aircraft have computer systems that can neither detect CMF nor recover from them. New systems are under investigation that can recover …

Flight Control Failure Detection And Control Redistribution Using Multiple Model Adaptive Estimation With Filter Spawning, Michael L. Torres Jr.

Theses and Dissertations

In the current research, the MMAE with Filter Spawning and Control Redistribution (MMAE/FS/CR) are used together to identify failures and apply appropriate corrections. This effort explores the performance of the MMAE/FS/CR in different regions of the flight envelope using model and gain scheduling. The MMAE/FS/CR is able to detect complete and partial actuator/surface failures, as well as complete sensor failures. Once the actuator/surface failure is identified and the effectiveness is determined in the case of partial failures, proper control is applied in order to accomplish the desired pilot command. Improvements in the algorithm are required in order to enhance the …

Optimal Aeroelastic Vehicle Sensor Placement For Root Migration Flight Control Applications, Abdul Ghafoor Al-Shenhabi

Mechanical & Aerospace Engineering Theses & Dissertations

An important step in control design for elastic systems is the determination of the number and location of control system components, namely sensors. The number and placement of sensors can be critical to the robust functioning of active control systems, especially when the system of interest is a large high-speed aeroelastic vehicle. The position of the sensors affects not only system stability, but also the performance of the closed-loop system. In this dissertation, a new approach for sensor placement in the integrated rigid and vibrational control of flexible aircraft structures is developed. Traditional rigid-body augmentation objectives are addressed indirectly through …

Three Dimensional Formation Flight Control, James K. Hall

Theses and Dissertations

Automating the control of an aircraft flying in formation necessitates the extension of the theory of formation flight control to allow for three dimensional maneuvers. The formation was modeled as a two-aircraft, leader and wingspan, formation. Both aircraft has its own three dimensional, rotating and translating, Cartesian axes system, with special attention being given to the motion of the leader in relation to the wingspan. The controller operated using the equations of motion expressed in the rotating reference frame of the wing aircraft. The control system has seven states, three inputs and three disturbance signals to model the dynamics of …

Design Of Flight Control Laws For Aircraft With Flexible Wings Using Quantitative Feedback Theory, Christina L. Osmon

Theses and Dissertations

Aircraft composed of lightweight composite materials are extremely enticing since their structural weight is greatly reduced. However, the control of these aircraft is complicated by the resultant flexibility of the wings. Two avenues of approach are possible; stiffen the wings thus losing some of the weight reduction benefits, or design the lateral/directional flight control system cognizant of the wing's flexibility. In this thesis the second approach is taken. The design of three lateral/directional flight control systems for the sub-sonic flight envelope of the F-18 is presented. The Quantitative Feedback Theory (QFT) robust control design technique is used. These designs incorporate …

Automation Of Formation Flight Control, Vincent P. Reyna

Theses and Dissertations

The research contained in this thesis explores the concepts of Automated Formation Flight Control documented in three previous AFIT theses. The generic formation analyzed consists of a Leader and Wingman, with the Wingman referencing its maneuvers off of Leader maneuvers. Specifically, planar formation flight control concerning only heading and velocity changes is considered. Next, the vertical separation constraint is relaxed to allow wing maneuvers outside of the flight plane of the lead in order to minimize the energy expended by the wing in a maneuver. Analysis of the two forms of formation flight control investigated in this thesis reveals the …

Evaluation Of Moderate Angle Of Attack Roll Of A Dual Engine, Thrust Vectoring Aircraft Using Quantitative Feedback Theory, Kevin E. Boyum

Theses and Dissertations

This thesis develops an innovative approach to the design of a flight control system for performing the large-amplitude velocity vector roll maneuver at high angles of attack AOAs. A six degree of freedom aircraft model is developed from the fundamental nine-state equations of motion using a modified linearization technique. The MIMO multiple-input multiple-output Quantitative Feedback Theory QFT robust control design technique is then used to jointly address the system nonlinearities present in this maneuver and the changes in the system parameters due to changes in flight condition, treating them as structured uncertainty in the design of a three-axis rate-commanded control …

Neural Networks For Dynamic Flight Control, Ronald E. Setzer

Theses and Dissertations

This thesis examines the application of artificial neural networks (NNs) to the problem of dynamic flight control. The specific application is the control of a flying model helicopter. The control interface is provided through a hardware and software test bed called the Fast Adaptive Maneuvering Experiment (FAME). The NN design approach uses two NNs: one trained as an emulator of the plant and the other trained to control the emulator. The emulator neural network is designed to reproduce the flight dynamics of the experimental plant. The controller is then designed to produce the appropriate control inputs to drive the emulator …

Design Of A Subsonic Envelope Flight Control System For The Vista F-16 Using Quantitative Feedback Theory, Odell R. Reynolds

Theses and Dissertations

A controlled plant's characteristics can vary widely throughout its operational envelope. This is a major problem in nominal plant-based control system design. Hence, gain scheduling is often used for full envelop design. In this paper, it is proposed to address the plant's variability using robust control design concepts. In particular, the frequency domain based Quantitative Feedback Theory Multiple-Input Multiple-Output robust control design method is employed for the synthesis of a full envelop flight control system for an F-16 derivative. Compensators for the aircraft's pitch and lateral directional channels are designed, and the designs are validated using linear simulations.

Development Of An Air-To-Air Refueling Automatic Flight Control System Using Quantitative Feedback Theory, Dennis W. Trosen

Theses and Dissertations

Quantitative Feedback Theory and the improved method Quantitative Feedback Theory are enhanced to include the rejection of disturbance at the system output. The enhanced Quantitative Feedback Theory and improved method Quantitative Feedback Theory processes are applied to the design of an automatic flight control system to regulate position of the C-135B fuel receiving aircraft relative to the tanker during air-to-air refueling. A simple feedback control system is developed that will achieve stable position regulation. State-space aircraft models &re generated. An inner loop autopilot is designed to reduce the plant cutoff frequency and provide the system inputs for the Quantitative Feedback …

Development Of High Angle Of Attack Control Laws For An Unstable, Non- Minimum Phase Aircraft Using Variations Of The Quantitative Feedback Technique, Mark A. Mcclure

Theses and Dissertations

This thesis discusses the application of variations of the quantitative feedback technique to a control problem with unstable, non-minimum phase plants. The X-29A research aircraft is used as the basis for developing a set of representative linearized aircraft dynamics models, which are modified to allow for the use of differential canard control inputs for enhanced maneuverability at extreme angles of attack. A specialized design approach is presented to develop frequency dependent weighting matrices, and the shortcomings of traditional methods are discussed. Four independent longitudinal compensators are developed by first designing loop transmission functions. Discussion is provided that addresses the limitations …

Model Identification And Control System Design For The Lambda Unmanned Research Vehicle, Gerald A. Swift

Theses and Dissertations

Research for this thesis centered on the Lambda Unmanned Research Vehicle (URV), an asset of the Flight Dynamics Directorate, Wright Laboratory Patterson AFB. The following tasks were accomplished: (1) a linear, state-space, small perturbation model was developed for both the longitudinal and lateral directional dynamics of the vehicles, and (2) pitch rate roll rate, and yaw rate flight controllers were designed using classical and multivariable feedback methods. The parameters of the linear, state space, small perturbation model were estimated from actual flight test data. Digital Datcom was first used to estimate stability and control derivatives from the vehicle's geometry. Maximum …

An Approach For Including Reliability In Control System Designs, Ime Isaac Akpan

Mechanical & Aerospace Engineering Theses & Dissertations

An approach is developed for non-catastrophic control component failure accommodation for large space structures. Reliability is considered for both the control configuration (i.e., selecting actuator locations over an admissible set) and the ultimate operation of the system. The approach presented is to construct a measure of performance that indicates the absolute goal of the system, and for a given structural design, to determine the lowest achievable cost conditional upon the failure states of the system (i.e., which actuators are operational). These costs are then weighted and summed to provide an overall system performance measure. This expected performance measure is then …