Power and Energy Commons^™

Development, Characterization, & Implementation Of Phase-Change Material Cold Plates For Hybrid-Electric Vehicle Battery Systems, Kevin Cwiok

Doctoral Dissertations and Master's Theses

Due to the regulations on internal combustion engine vehicles, there is a large demand of hybrid and electric vehicles with large battery packs as Energy Storage Systems (ESS) capable of long ranges and decreased emissions. These battery packs output large heat loads during charge-depletion mode and currently require active cooling to keep the batteries within operating conditions. The current systems relied onto achieve this are the air and liquid cooled thermal managements systems. A recent alternative approach to current cooling for ESS thermal management is the use of phase-change materials (PCMs). PCMs regulate the temperature of the ESS by leveraging …

Power Distribution:Protection Analysis, Avneet S. Samra

Electrical Engineering

The objective of this project is to build a radial distribution system that operates on a lower voltage. The system consists of a transmission line protected by a SEL-351 Relay, a three- phase transformer protected by a SEL-587 Relay, and a three-phase induction motor protected by a Cooper Form 6 Controller. The SEL-351, SEL-587, and the Cooper Form 6 Controller are microprocessor-based relays that are used to provide protection under faulted conditions. When a fault is detected in the system, the closest upstream relay sends a trip signal to its assigned local breaker. The SEL-351 provides overcurrent protection for the …

Designing A Power Distribution System For The Arce 257 Revit Structural Model, Reid Wilhelm

Electrical Engineering

The construction industry needs engineers. Mechanical, electrical, and plumbing engineers, better known as MEPs, comprise a large number of employees who design and assist in the building of commercial structures. In particular, electrical engineers design power distribution systems for these buildings, including the power, lighting, low voltage, and fire protection subsystems.

Here at Cal Poly, architectural engineers enrolled in ARCE 257 create authentic structural plans for a fictitious two-story structure. This senior project transforms these structural plans into an architectural model and creates a power distribution system for the entire building. This is done through a building information modeling (BIM) …

Single Carrier Frequency Domain Equalization And Energy Efficiency Optimization For Mimo Cognitive Radio., Xiaohui Zhang

Electronic Theses and Dissertations

This dissertation studies two separate topics in wireless communication systems. One topic focuses on the Single Carrier Frequency Domain Equalization (SC-FDE), which is a promising technique to mitigate the multipath effect in the broadband wireless communication. Another topic targets on the energy efficiency optimization in a multiple input multiple output (MIMO) cognitive radio network. For SC-FDE, the conventional linear receivers suffer from the noise amplification in deep fading channel. To overcome this, a fractional spaced frequency domain (FSFD) receiver based on frequency domain oversampling (FDO) is proposed for SC-FDE to improve the performance of the linear receiver under deep fading …

Optimal Sensing And Transmission In Energy Harvesting Sensor Networks, Xianwen Wu

Graduate Theses and Dissertations

Sensor networks equipped with energy harvesting (EH) devices have attracted great attentions recently. Compared with conventional sensor networks powered by batteries, the energy harvesting abilities of the sensor nodes make sustainable and environment-friendly sensor networks possible. However, the random, scarce and non-uniform energy supply features also necessitate a completely different approach to energy management.

A typical EH wireless sensor node consists of an EH module that converts ambient energy to electrical energy, which is stored in a rechargeable battery, and will be used to power the sensing and transmission operations of the sensor. Therefore, both sensing and transmission are subject …

Quantum Dot Band Gap Investigations, John Ryan Peterson

Student Works

Improving solar panel efficiency has become increasingly important as the world searches for cheap renewable energy. Recent developments in the industry have focused on multi-layer cells, some of which use semiconducting dyes to absorb light in place of crystalline solids. In this paper, I characterize various dyes recently synthesized for use in solar panels. These dyes contain semiconducting nanoparticles enclosed primarily by the protein ferritin to limit particle size. The band gaps were measured using either optical absorption spectroscopy or measuring the photoluminescence spectrum, depending on the type of semiconductor. The results indicate that both manganese oxide and lead sulfide …

Optimized Sizing And Placing Of Distributed Energy Resources (Ders) In An Island Microgrid Using Der-Cam, Bhuwan B. Bastola

Electrical and Computer Engineering ETDs

The electric grid at La Gomera, an island in the Canary archipelago, has been the subject of interest in optimized integration of Distributed Energy Resources (DERs) primarily because of high distribution losses and concerns about complying with emission regulations. Consequently, the utility that operates the island power system wishes to mitigate the problem with installation of renewable and distributed energy sources like PV and battery, which is the focus of this research.

Specifically, the focus of this thesis is to use Distributed Energy Resource - Customer Adoption Model (DER-CAM) to optimize the installation of PV and battery in terms of …

"Feasibility Of Efficient Photovoltaics In Eastern Kentucky" / "Developing A 3-D Printed Solar Vehicle With Computational Fluid Dynamics (Cfd) Simulator", Adam N. Stanley, Matthew R. Hezseltine

Posters-at-the-Capitol

Abstract 1

Feasibility of Efficient Photovoltaics in Eastern Kentucky

Photovoltaics (PV-also called solar photovoltaic devices) are used to harness the power of the sun via the electronic process that occurs within semiconductor cells. The solar energy is absorbed by the cells, which causes the electrons to break away from their atoms, allowing them to flow within the material to produce electricity. This electricity will become the renewable energy for Kentucky, as the generation of coal will but come to a stop within the near future. Like Denmark who is running on 100% renewable generation we must stride to become fully …

Modeling Of A Multi-Megawatt Grid Connected Pv System With Integrated Batteries, Vandana Rallabandi, Oluwaseun M. Akeyo, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The multi-megawatt grid connected photovoltaic (PV) system studied in the paper includes parallel arrays and power electronic units, each with their own DC-DC and DC-AC converters. In one configuration, the DC-AC converters of adjacent parallel sections are connected in cascade, in order to effectively operate as a multilevel inverter, thereby reducing the filtering requirements. Grid voltage oriented control is employed for inverters and a battery is incorporated for energy storage and performance improvement. Modeling is performed with the PSCAD/EMTDC software, such that both the power electronics components, controls and subsystem aspects, and the electric grid power system issues, can be …

Benchmarking Approach For Empirical Comparison Of Pricing Models In Drms, Seif Azghandi, Kenneth M. Hopkinson, Kennard R. Laviers

Faculty Publications

emand response management systems often involve the use of pricing schemes to motivate the efficient use of electrical power. Achieving this efficiency requires the detection of electrical power patterns. The detection of these patterns normally involves use of non-linear, quasi-non-linear, and at times linear data pattern detection models. The behavioural disparities of these models and specifically when used for a specific set of data make it hard to select the most efficient model. The contribution of this study is devising an empirical benchmark (reference) ( perfect ) control pricing (PCP) model through which various models are compared in order to …

Advances And Prospects Of Lithium-Sulfur Batteries, Shou-Yi Yuan, Ying Pang, Li-Na Wang, Yong-Gang Wang, Yong-Yao Xia

Journal of Electrochemistry

Lithium-sulfur batteries have recently attracted worldwide attention due to the high specific theoretical energy density of sulfur cathode (2600 Wh⋅kg^-1), low cost and wide availability of sulfur. However, the practical application of lithium-sulfur batteries has been hindered by several challenges, such as the shuttling of polysulfide intermediates, the large volume expansion of sulfur during charge/discharge and the dendrites formation on lithium anode. Foremost among these is the shuttling effect arising from the dissolution of lithium polysulfides intermediate into the electrolyte from the cathode reaction and their diffusion to the anode where they react with metal lithium to form …

Research Progress In Cycle Stability Of Silicon Based Li-Ion Battery Anodes, Ze-Liang Guo, Hui Wu

Journal of Electrochemistry

Silicon(Si), with the highest specific capacity currently known, is a promising anode material for Li-ion battery. However, in the charging and discharging process, with Li atoms inserting into and breaking out of the Si crystal lattices, the Si anode undergoes enormous volume expansion and contraction, ending in pulverization. The fact that the specific capacity of bulk Si anodes drop quickly is a challenging problem. In this review, we summarize recent progresses in Si anode. We concern about the nanostructure of silicon, cooperation of silicon with other additives and macrostructure design of anodes. We discuss strengths and shortcomings of different methods, …

Effects Of Lithium Salts On The Properties Of Hyperbrandched/Comb-Like Composite Polymer Electrolytes, Xian-Lei Hu, Xiao-Xu Liang, Ming-Qiu Zhang, Ruo-Xin Zhang, Li-Ping Zhang, Wen-Hong Ruan

Journal of Electrochemistry

Based on the chemical characteristics of the hydroxyl group of PVA side-chain, the hyperbrandched poly(amine-ester) (HBPAE) was used to hypergraftingly pretreated nano-silica (SiO₂) and polyving akohol (PVA). And different lithium salts were added to fabricate the SiO₂-g-HBPAE/PVA-g-HBPAE hyperbrandched/comb-like composite polymer electrolytes (CPEs). The dispersion of nanoparticles in matrix was observed by SEM. The effects of different lithium salts on the properties of CPEs were studied by DSC, tensile test and dielectric spectra. The results showed that the hypergrafting method improved the interphase compatibility between SiO₂ and matrix. Sulfonic acid type lithium salts accelerated self-plasticizing with …

The Study Of Dynamical Electrochemical Impedance Spectroscopy For Oxygen Reduction Reaction On Pt/C Catalyst, Kun-Ming Shi, Jian-Wei Guo, Jia Wang

Journal of Electrochemistry

With joint techniques of rotating disc electrode(RDE) and electrochemical impedance spectroscopy(EIS), and further establishment on equivalent circuit model, this paper studied oxygen reduction reaction(ORR) on commercial Pt/C catalyst in acid medium. Our results found that the dynamical interface on Pt/C consists of two independent processes: 1) the PtO reduction from Pt surface, 2) the new PtO formation from ORR, thus providing key clues for catalyst stability and activity. This also implied that the dynamical interface facilitates reconstruction for porous electrode, and matches with mass transfer. One important issue is discovered that at high overpotential, the high reaction rate for ORR …

Research Progress Of Si-Based Anode Materials For Lithium-Ion Batteries, Ding-Qiong Chen, Yang Yang, Qiu-Li Li, Jin-Bao Zhao

Journal of Electrochemistry

Owing to its high theoretical specific capacity (4200 mAh·g^-1), silicon is a promising candidate to replace graphite as the anode in lithium ion batteries (LIBs). However, low intrinsic electric conductivity and dramatic volume change (~ 300%) during the process of lithiation and delithiation result in electrode pulverization and capacity loss with cycling, accordingly, the application of silicon as an anode in LIBs has been severely hindered. We will discuss the structure of silicon electrode including synthesis of Si-based composites,the selection of binder for silicon and the fabrication of binder-free Si-based electrode, as well as the electrolyte additive to …

Research And Application Of Key Materials For Sodium-Ion Batteries, Yong-Chang Liu, Cheng-Cheng Chen, Ning Zhang, Liu-Bin Wang, Xing-De Xiang, Jun Chen

Journal of Electrochemistry

Sodium-ion batteries (SIBs) have been considered as a potential large-scale energy storage technology owing to the abundance, wide distribution, and low price of sodium resources. However, the larger and heavier sodium ion as compared to lithium ion makes it difficult to identify appropriate electrode materials with the capability for fast and stable sodium-ion insertion/extraction. Furthermore, the optimization of electrolyte, the matching of cathode and anode materials, and the construction of sodium-ion full batteries with high-performance, high-safety, and low-cost are urgently needed in order to make SIBs commercially available. This review summarizes the up-to-date research progresses in key materials (including cathode, …

Micro/Nano-Structured Electrode Materials For Sodium-Ion Batteries, Shuang Yuan, Yun-Hai Zhu, Sai Wang, Tao Sun, Xin-Bo Zhang, Qiang Wang

Journal of Electrochemistry

Sodium has similar physics and chemical properties to lithium, alternatively, sodium (Na)-ion batteries have again aroused a great deal of interest recently, particularly for large-scale stationary energy storage applications due to the practically infinite sodium resources and low cost. However, the technics and materials for Na-ion batteries are immature. Therefore, development of advanced anode and cathode materials for Na-ion batteries is urgently desired but remains a great challenge. This paper briefly reviews some recent progresses in this field, addressing the morphology effects, as well as functions of carbon composite materials toward Na-ion batteries. Several electrode materials with micro/nano-structures based on …

Template-Assisted Hydrothermal Synthesis Of Nio@Co3O4 Hollow Spheres With Hierarchical Porous Surfaces For Supercapacitor Applications, Wen Zhou, Xue-Feng Lu, Ming-Mei Wu, Gao-Ren Li

Journal of Electrochemistry

Hollow structures have shown great potentials in a variety of important applications, such as energy conversion and storage. In order to further enhance the performance, the rational design of hollow structures with higher complexity in terms of composition and structure is highly desirable and still remains a great challenge. In this work, an efficient strategy was established for the fabrication of novel NiO@Co₃O₄ hollow spheres (HSs) with hierarchical porous surfaces by silica spheres template-assisted hydrothermal synthesis. The as-fabricated NiO@Co₃O₄ HSs showed high specific surface area of 219.68 m²·g^-1, and significant …

Electrochemical Performance Of Crystalline Li12Si7 As Anode Material For Lithium Ion Battery, Ya-Xiong Yang, Rui-Jun Ma, Ming-Xia Gao, Hong-Ge Pan, Yong-Feng Liu

Journal of Electrochemistry

Crystalline Li₁₂Si₇ is successfully synthesized by heating the mixture of LiH and Si with a molar ratio of 12:7, which avoids the huge difference of the melting points between Li and Si. The electrochemical performance and lithium storage mechanism of the as-prepared Li12Si7 are studied in this work. It is found that only a change in cell volume takes place without a phase change during the lithiation/delithiation of Li₁₂Si₇ at a voltage range of 0.02 ~ 0.6 V, exhibiting a solid-solution lithium storage mechanism. Such a lithium storage process effectively retards the volume effect …

Continuous Synthesis And Condition Exploration Of Precursor Ni1/3Co1/3Mn1/3(Oh)2 Ternary Cathode Material, Zhi-Jun Jiang, Ya-Li Zhang, Qian Wang, Hui Zhang

Journal of Electrochemistry

Commercial LiNi_1/3Co_1/3Mn_1/3(OH)₂ ternary material is generally prepared by a combination of co-precipitation and solid state reaction method. The particle size distribution and morphology of Ni_1/3Co_1/3Mn_1/3(OH)₂ precursor have a great impact on the electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂. In this work, the precursor Ni_1/3Co_1/3Mn_1/3(OH)₂ ternary cathode material was prepared by co-precipitation method with MnSO₄, NiSO₄, and CoSO₄ as raw materials, NaOH as a precipitating agent and NH_{3 …}