Process Control and Systems Commons^™

The Algorithm For The Design Of Fine Granular Substances’ Smart-Type Heat And Moisture Converters Based On Their Accuracy And Speed Criteria, Erkin Uljaev, Ali Abduakhatovich Abduraxmanov

Chemical Technology, Control and Management

The paper describes a technique and algorithm allowing to perform parametric design of smart-type heat and moisture converters (hereinafter SHMC) of fine-grained dispersive materials based on their criteria of accuracy and speed. The proposed algorithm optimizes the process of design of smart-type switches and ensure optimal performance of the switches. The method of calculation and selection of optimal parameters of smart-type heat and moisture converters intended to be used in the measurement of parameters such as heat and humidity of fine dispersive substances are aimed at boosting two parameters, i.e., the accuracy and speed. Also, the design stages have been …

Synthesis Problem Of Adaptive Control Systems For Multi-Channel And Multi-Mode Objects, Jasur Usmonovich Sevinov, Abdishukurov Maqsud O'G'Li Shavkat Mr, Nasriddin Xasanovich Bobomurodov

Chemical Technology, Control and Management

The issue of synthesis of an adaptive control system for multi-channel and multi-mode objects is considered. Development that of effective adaptive control algorithms for nonlinear dynamic systems ensure quality indicators of processes. In technological processes, it is necessary to control several parameters or several systems at the same time. For such a process control system, an adaptive control system is created. Work has been carried out on structural projects for the installation of adaptive systems. The stable requirements for the correction of adaptive control systems are seen. A review of several parametric deviation detections, based on the reference model and …

Study Of Technological Multi-Stage Modes Of Refining Vegetable Oils, Elyor Erkinovich Samadov

Chemical Technology, Control and Management

The work reflects the current state of the technology for obtaining refined vegetable oils and identifies trends in their improvement and further development in the environment of industrial automation using modern methods of distributed monitoring, building control, and management systems for technological processes of refining vegetable oils. The influence of technological modes of refining vegetable oils on the efficiency of diffusion extraction of free fatty acids (FFA) has been studied and the indirect pH-metric measurement of FFA concentration has been substantiated.

Algorithm For The Functioning Of The Robot's Mechatronic System, Nodira Batirdjanovna Alimova, Bekmurod Bayotovich Yusupov

Chemical Technology, Control and Management

Currently, the introduction of mechatronics and robotics into modern technologies, including rural industry, which are based on different types of mechatronic modules, is relevant. The article discusses the functioning algorithm of the electro-pneumatic multi-position mechatronic system of an intelligent robot. The mechatronic system under consideration is an integrated complex of electro-pneumatic elements, electronic elements and computer technology, with constant dynamic changes in energy and information between them, united by a common automatic control system. The main distinctive feature of this mechatronic system is increased positioning accuracy and high traction forces.

Trends In The Development And Improvement Of Glass Furnaces And Monitoring And Control Systems, N.R Yusupbekov, O'Tkir U. Xolmanov

Chemical Technology, Control and Management

The theory and practice of establishing industrial automation systems for glass furnaces and installations as they are right now are taken into consideration. Comparative analysis is based on publications over the last 20 years in the field being studied. On the basis of an analysis of the review materials, generalizations are made that form the basis for proposals aimed at modernizing and improving the technology and instrumentation of fuel combustion processes in gas-burning furnaces and installations, as well as monitoring and control systems for technological processes occurring in glass furnaces and installations.

Assessment Of Spatial Variability Of Groundwater Potential Using Remote Sensing And Gis-Based-Criteria Evaluation For Dar Es Salaam, Tanzania, Augustina Alexander

Tanzania Journal of Engineering and Technology (TJET)

Groundwater is an important resource for the continuous provision of water supply in both urban and rural areas. Lack of enough knowledge about the spatial variability of groundwater potential zones (GWPZS) has a negative impact on groundwater extraction development and management and may result into over exploitation. In this study, analytic hierarchy approach (AHP)-coupled with multi criteria decision analysis (MCDA) and GIS techniques were employed to integrate hydrogeological, geological as well as topographical data to assess spatial variability of groundwater potential zones of Dar es Salaam city. Seven thematic layers such as lithology, slope, land-use, lineament, drainage, soil, and rainfall …

Designing A Cylindrical Capacitive Based Sensor For Monitoring The Table Salt’S Moisture Content During Iodization, Mwajuma Lungo

Tanzania Journal of Engineering and Technology (TJET)

Coaxial cylinder capacitive moisture sensor for determination of moisture content of table salts has been fabricated. The CMS method for determination of moisture content of table salts overcomes the effect of evaporation of iodine in table salt which results from heating in the oven drying method. The CMS overcomes the polarization effect result from the resistive methods of moisture content determination and it is non expensive to construct and it has high accuracy since measurements involves programming system in interpretation of the results. In this research, moisture content sensor based on capacitive principal created using two coaxial cylinders with height …

Dynamic Influence Diagram-Based Deep Reinforcement Learning Framework And Application For Decision Support For Operators In Control Rooms, Joseph Mietkiewicz, Ammar N. Abbas, Chidera W. Amazu, Anders L. Madsen, Gabriele Baldissone

Articles

In today’s complex industrial environment, operators are often faced with challenging situations that require quick and accurate decision-making. The human-machine interface (HMI) can display too much information, leading to information overload and potentially compromising the operator’s ability to respond effectively. To address this challenge, decision support models are needed to assist operators in identifying and responding to potential safety incidents. In this paper, we present an experiment to evaluate the effectiveness of a recommendation system in addressing the challenge of information overload. The case study focuses on a formaldehyde production simulator and examines the performance of an improved Human-Machine Interface …

Use Of Neural Networks In Intelligent Measurement Tools, N.R Yusupbekov, Y.Sh. Avazov, Umidjon Ruziev Phd

Chemical Technology, Control and Management

The paper presents algorithms for processing the measurement signal with the possibilities of adaptation, learning and decision making. A comparative analysis of the methods of intellectual processing of measurement data is carried out. A model of a measuring instrument for determining the structure of a neural network has been developed. The problem of error reduction due to measurement noise filtering with the use of neural networks is considered. The structure of the neural network has been developed for intelligent processing of the measurement signal and ensuring the implementation of the functions of reconfiguration, calibration, self-diagnosis and self-control. A neural network …

Algorithms For Synthesis Of Adaptive Control Systems Based On The Neural Network Approach, Jasur Sevinov, Oxunjon Boborayimov, Sh.M. Abdishukurov

Chemical Technology, Control and Management

Here are algorithms for the synthesis of adaptive control systems based on the neural network approach presented. The issues of choice of architectures of neural networks that produce parametric identification of the object regulation. Adaptative neural networks that reproduce the optimal parameters of implemented controllers, methods of forming training samples for their training are considered. The other question of using the theory of artificial neural networks for approximating the functional of the controller's tuning parameters are determined. Structures of synthesized neural networks of parametric identification of objects with self-alignment in an open loop ACS are proposed. Algorithms made it possible …

Results Of The Study Of The Pumpkin Drying Process, Jasur Esirgapovich Safarov, Shahnoza Abduvakhitovna Sultanova, Andrey Svyatoslavovich Ponasenko, Gani Toshkhujaevich Dadaev

Chemical Technology, Control and Management

The article presents the results of the study of the pumpkin drying process, comparisons with different drying models are carried out. A mathematical model for numerical analysis has been developed. Pumpkin drying rates are calculated and various drying models are investigated. 5 different drying models were used to verify the accuracy of experimental data and search for the most suitable model. The experimental data obtained for the drying air temperature of 45 °C, 55 °C and 65 °C were applied to various drying models.

Systematic Analysis Of Methods Of Control Of Dynamic Objects In Conditions Of Non-Measurable Disturbances, Mamirov Farkhodovich Uktam, Buronov Mamurjon Ugli Bunyod

Chemical Technology, Control and Management

The article presents a systematic analysis of control methods of dynamic objects under non-measurable disturbances. It is important to study all the factors affecting the control object in order to increase the efficiency of the control system. Due to the immeasurable nature of disturbances affecting control objects, it is shown that they cause negative effects and increase the complexity of control systems in this case. In the control of dynamic objects of this type, the possibilities of control by indirect measurement of disturbances or by estimation of object position and disturbances have been explored. The use cases, shortcomings and achievements …

Development Of The Computer Model Of The Waste Water Treatment Process Using Ion-Exchange Resins In The Matlab Program, Jaloliddin Abdurazzakovich Eshbobaev, Bakhodir Tajiddinovich Khamidov, Adham Tilovovich Norkobilov, Orifjon Sharipovich Kodirov

Chemical Technology, Control and Management

In this work, a mathematical model of industrial wastewater treatment technology was formed. First, wastewater treatment technologies were analyzed and the technology of ion-exchange resin treatment was selected. A water purification device using ion-exchange resins was made, and tested on the Kungrad soda plant and the results were obtained. According to these results, it was determined that the cleaning coefficient of the device is up to 98-99%. In this article, a mathematical model of a wastewater treatment device using ion-exchange resins was developed using the stoichiometric matrix method. After the mathematical model of the process was found, a graph of …

The Morphology Analysis Of Soil In Remote Sensing Image Processing, Mirzayan Mirzaaxmedovich Kamilov, Mirzaakbar Xakkulmirzayevich Hudayberdiev, Bobomurod Mamitjonovich Tojiboev

Chemical Technology, Control and Management

This article analyzed various techniques used in satellite image processing to analyze soil morphology. Analysis of soil morphology using satellite imagery plays a crucial role in soil science research, Land Management, and environmental monitoring. It provides an economical and efficient means of studying large-scale soil variability, providing information on land sustainable use, resource management and soil conservation decisions.

Computer Training Systems For Training Engineering Personnel For Control Industrial Enterprises, Yusuf Shodiyevich Avazov, Kamola Rustamovna Abdullaeva

Chemical Technology, Control and Management

A principle has been proposed for constructing computer simulators for improving the qualifications of process control operators at industrial enterprises and for training students of higher educational institutions. The capabilities of a computer simulator that can be used as a digital assistant are revealed. Their architecture for building digital simulators is proposed. From the architecture it is clear that the computer simulator consists of two systems. The training process management system and the server of the computerized simulator are combined into a digital simulator. Simulators in this category provide student operators with the opportunity to develop skills in self-control of …

Obtaining Sweet Molasses By The Method Of Hydromechanical And Enzymatic Processing Of Grain, Sadritdin Maxamatdinovich Turabdjanov, Kamoliddin Ahmadjonovich Mahmudov, Bexzod Alisherovich Kasimov, Kasun Dissanayake Kumara

Chemical Technology, Control and Management

Methods of hydrolysis of grains to starch under the influence of hydrodynamic and enzymatic processes are logically based. Polysaccharides derived from starchy grains are known and popular in the food industry for their thickening and stabilizing properties. To date, studies that allow for a deeper understanding of the mechanism of interaction of polysaccharide-containing products with their main components, the effect on the set of rheological, organoleptic, physico-chemical properties of food products that determine their functions are relevant.

Mathematical Model Of An Industrial Robot Built On The Basis Of Linear Motion Mechatron Modules, Matyokubov Nurbek Rustamovich, Rakhimov Temurbek Omonboyevich

Chemical Technology, Control and Management

The use of Industry 4.0 technologies in modern production serves to increase production efficiency. Robots and robotic complexes with innovative intelligent control are widely used in industrial production. However, studying their mechanical part, linear motion mechatronic modules and control system is a complex object. The variety and complexity of control methods and operating modes negatively affects the operator's working time and production productivity. In such cases, it is necessary to improve control methods and develop technologies used in industry, including robots and robotic manipulators, which allow to perform short movements with high accuracy and speed. In the article, the mathematical …

Application Of Evolutionary Algorithms For Optimization Of Operation Modes Of Regional Electric Power Systems, Isamiddin Khakimovich Siddikov, Oksana Vitalevna Porubay

Chemical Technology, Control and Management

The paper presents the possibilities of using evolutionary algorithms to solve the problem of optimizing the operation modes of electric power facilities in the presence of constraints in the form of inequalities and equalities. The limits of constraints have a variable character, depending on the generated and consumed energy. Existing methods used for the optimization of modes are based on general principles and approaches to optimization, which usually adapt to the specifics of the problem. In electric power facilities, optimization problems have some peculiarities, among which is the presence of multiple constraints applied to both independent and dependent variables. Many …

Addition Of Process Control Experiment To Unit Operations Ii Laboratory., Bradley Esselman

Electronic Theses and Dissertations

Process control is an essential aspect of manufacturing, contributing to improved process safety, efficiency, product consistency, and energy optimization. Chemical engineers are often responsible for ensuring the safe, efficient, and cost-effective operation of industrial processes, and process control plays a pivotal role in accomplishing this.

Chemical engineering students at the University of Louisville complete the course, Elements of Process Control, during the second semester of their fourth year. This lecture-based course offers limited hands-on, practical experience. To supplement the lack of hands-on experience in the classroom, a new process control experiment was designed and implemented into the Unit Operations …

Improving Lignin Recovery From Paper Mill And Biorefinery Waste Streams Via Liquid-Phase Splitting, Carter Fitzgerald

All Dissertations

Lignin is an abundant biopolymer with significant promise due to its aromaticity. It has been targeted as a replacement for a number of petroleum-based products including adhesives, coatings, polyurethane foams, activated carbon, and carbon fibers. However, commercially available bulk lignins are too polydisperse, and contain too many residual metals from the pulping process that are detrimental to the properties of the final product.

The Sequential Liquid-lignin Recovery and Purification (SLRP) process was developed by Michael Lake and John Blackburn, in collaboration with Clemson, with the intention of creating a continuous method for recovering lignin from paper-mill black liquors. Thies and …