Process Control and Systems Commons^™

Study Of Kinetics Of Hydrocarbon Gas Purification With Composite Absorbents, Oybek Aripdjanov, Shavkat Nurullaev, Shodiyakhon Azimova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the work is to improve the process of natural gas purification from acidic components using a composite absorbent. To study the sorption of acidic components in the gas composition, a chromatographic analysis method was used. The kinetics and rate of corrosion of carbon steel grade st.10 when using composite absorbents MDEA +DEA + AVRP have been studied. The results of the study show that the volume of absorption increased from 0.55 mol/mol to 0.65 mol/mol, and the amount of H₂S in the purified gas decreased from 0.022 g/m³ to 0.014 g/m³. Corrosion …

Study Of Reactive Distillation Equipment For Eterification Process, Abbos Elmanov, Abdulaziz Bakhtiyorov, Adham Norkobilov, Olimjon Maksudov, Zarif Oripov

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of this work is to study the chemical technological processes for eterification processes, and the reactive distillation unit, which carries out the reaction and separation process in one device, was chosen as the object of research. А reаctive distillаtion system is exаmined to produce for the production of Ethyl Acetate (EtAc) viа eterificаtion of acetic acid (HAc) with ethаnol. Optimizаtion methods using sensitivity analysis аre аlso conducted. Cаlculаtion of vаpor liquid equilibrium of the mixture system is done using UNIFАC model. Heat integration from the distillate stream of the column to the acid feed stream and from bottom …

Modeling And Performance Analysis Of Solid Oxide Fuel Cell, Mariya Pecherskaya, Khakimjan Butanov, Suhrob A. Ibodullaev, Olim Ruzimuradov, Shavkat Mamatkulov

CHEMISTRY AND CHEMICAL ENGINEERING

A three-dimensional numerical model of the system configurations of various types of solid oxide fuel cells (SOFCs) is used and the effect of parameters on SOFC performance is numerically investigated using COMSOL Multiphysics. The effect of parameters such as support layer thickness, operating temperature, and electrode porosity are shown in the polarization and power curves for each model. The results of the study showed the advantages of the anode-supported SOFC compared to cathode- and electrolyte-supported SOFC.

Theoretical calculations demonstrate the highest output power density in the anode-supported SOFC at 900 ℃, and reach a value of 0.585 W cm^{-2 …}

Cfd Study On Two-Phase Flow Patterns In A Pipe With 90º Elbow In Different Operating Conditions, Hagar Alm-Eldin Bastawissi, Mohammed Ahmed Khafagy, E. A. El Shenawy Prof. Dr., Ahmed M. Salem Dr

Journal of Engineering Research

Recently, CFD has offered a technological solution for modelling multi-phase flow in which we can make endless simulations with reduced expenses and effort in high accuracy results; we shall also mention that experimental studies have limitations for safety considerations when experimenting with flow in high temperature or pressure values or medium nature as in nuclear or chemical flows.In this paper, we used the ANSYS FLUENT CFD program to simulate the two-phase flow in a pipe to study the effect of attaching a 90-degree elbow fitting to the piping system, seeking to find out the change in the pattern and resulting …

Strategy For Predictive Control Of The Rectification Process Based On A Model Controller With A Given Forecast, Ildar Rafkatovich Sultanov

Chemical Technology, Control and Management

A method is being developed to optimize the generated controls for the multicomponent distillation process with prediction, based on predictive data with a moving horizon. The difference between this method and the classical modeling approach, in which the percentage of the degree of opening of valves installed on the output streams of the column is used as control actions, is that control occurs on the feedback principle. The proposed method is based on the use of a dynamic process model to optimize control actions in real time in order to achieve certain production targets. The essence of the MPC approach …

Identification Of Faults In Highways Using Approximation Methods And Algorithms, Khudayberdiyev Khakkulmirzayevich Mirzaakbar, Anvar Asatilloyevich Ravshanov

Chemical Technology, Control and Management

Many fast Fourier transforms are used to identify defective parts of uneven surfaces on roads and send information to relevant organizations on the road, using the " RAVON YO‘LLAR" application installed on a mobile device during car movement. We determine the uneven parts of the road. Smooth and well-maintained roads reduce the risk of vehicle collisions, skidding and other road-related incidents. Timely measures contribute to overall safety, comfort and economic efficiency.

A Neural Network Model For Monitoring And Forecasting The Process Of Storing Oilseeds, N.A. Kabulov

Chemical Technology, Control and Management

The paper presents the results of research on the control, forecasting and management of the storage process of oilseeds. Vegetable oil production and energy consumption are two important factors of oilseed storage systems. The first ones should meet the needs of the population quantitatively and qualitatively. As a result, in order to properly control these two important aspects, it is necessary to maintain an appropriate microclimatic environment using a computational decision support system (DSS) that is able to adapt to changes in environmental characteristics. The multilayer perceptron neural network (MLP-NN) was developed to simulate the temperature and relative humidity profiles …

Synthesize A Neural Network Parameter Optimizer For An Adaptive Pid Controller, Nashvandova Gulruxsor Murot Qizi

Chemical Technology, Control and Management

Wide application of proportional-integral-differential (PID)-regulator in industry requires constant improvement of methods of its parameters superstructuring. In the paper, the questions of optimization of PID-regulator parameters with application of methods of neural network technology are considered. A methodology for selecting the architecture of neural network optimizer designed to determine the tuned parameters of PID regulator is proposed. The algorithm of training of the neural network, with the set on the basis of the method of inverse gradient propagation is offered. The proposed improved PID-neural regulator allowed to provide stabilization of neural network operation and its trainability in the control loop …

Development Of A Criterion Assessing The Level Of Relationship Of Multiple Identified Characteristics For Classification, Mirzoyan Mirzaaxmedovich Kamilov, Oybek Zokirovich Koraboshev, Bobomurod Mamitjonovich Tojiboev

Chemical Technology, Control and Management

This article discusses an optimized version of the standard design developed by Yu.I.Zhuravlev, an optimization procedure through an algebraic approach based on precedent algorithms that solves the problem of pattern identification. The formation of the convex hull of the recognition operator and corrective procedures of information models by mutual compensation of each other was also studied. In addition, the functional connection of recognition operators and the definition of idempotent connection of operators are analyzed.

Analytical-Critical Review Of Widely Used Industrial Devices For Drying Mineral Fertilizers, Djalolitdin Paxritdinovich Mukhitdinov, Aleksey Viktorovich Schulz

Chemical Technology, Control and Management

The article is devoted to the review of the modern state of research in the mineral fertilizers drying field, critical analysis and comparison of widely used drying apparatuses. There are procedures of preliminary equipment selection for soluble fertilizers industrial drying on the basis of such criteria as productivity, efficiency, energy saving, environmental impact degree, indicating the possible advantages and disadvantages of different application variants.

Calculation Of Hydraulic Resistance Of A Tubular-Gridse Nozzle With Spiral Turbulizers, Nurmukhamedov Habibulla Sagdullaevich, Mavlonov Elbek Tulkinovich, S.Kh. Nishonova, Kh.S. Nurmukhamedov

Chemical Technology, Control and Management

The article presents the results of an experimental study on the hydraulic resistance of a tubular-grid nozzle made of smooth pipes and pipes with spiral turbulators. Experiments were carried out with nozzles made of smooth pipes and pipes with turbulators. Spiral turbulators are placed discretely with a step t/d=0,3125-0,9375 and installed on a tube sheet in a checkerboard pattern with a step s/d=1,15-10. Experimental studies were carried out with air flow in the transition region.

It has been established that with increasing numerical values of the dimensionless parameter s/d, the resistance of the pipe package decreases from 1,3 to 1,8 …

Chromatographic Analysis Of The Chemical Composition Of Pyrolysis Distillate, Sh.T. Juraev, B.F. Muxiddinov, U.T. Tailakov

Chemical Technology, Control and Management

The paper presents the results of a study of the physico-chemical characteristics of the liquid fraction of products of thermal oxidative pyrolysis of worn tires. The mass fraction of the volatile gas compounds, the optimal boiling points of the obtained condensates and the flashpoint of pyrolysis liquids, together with the mass composition of cracking products of rubber products at high-temperature pyrolysis at a temperature of 800-900 °C, were determined. Chromatographic analysis allowed us to determine the composition, mainly the mass composition of pyrolysis products, which consisted of carbon (42.8%), higher aliphatic and aromatic hydrocarbons (17.0%), methane (10.2%), benzene (4.2%) and …

Development Of A Mathematical Model Of Magnetic Field Distribution In Magnetic Conductors Of A Wide-Range Current Transformer, Abdurauf Safarov

Chemical Technology, Control and Management

The article is devoted to the analysis of the distribution of the magnetic field in the magnetic conductors of a wide-range current transformer for the development of a mathematical model that can be used as the basis for calculating its static characteristics and error. The design, replacement circuits and design model of a current transformer are given. The relations of magnetic induction and tension from the coordinate of the position of the primary winding are obtained. It is shown that the conversion range can be adjusted depending on the different positions of the bus with current, as a result of …

Design Of Active Pharmaceutical Ingredients Solid States In Crystallization Processes, Weizhong Gong

Electronic Thesis and Dissertation Repository

Crystallization is an important technique to obtain solid-state drugs from solutions. Physicochemical properties of the active pharmaceutical ingredients (APIs) are determined by crystallization. More than half of the active pharmaceutical ingredients exhibit polymorphism, the phenomenon of chemical species showing more than one unit-cell structure in the solid state. Controlling polymorphism is one of the most important goals during pharmaceutical manufacturing. Nevertheless, the control of polymorphism is sometimes not enough to realize the targeted physicochemical properties. Suitable additives (coformers/salt formers) are explored to generate new multi-component solid phases of poorly soluble/bioavailable active pharmaceutical ingredients (APIs). The design of pharmaceutical cocrystals and …

Study Of The Application Of Blender For Simulation Of A Closed-Loop Image-Based Greenhouse Supplemental Lighting Control, Kip Nieman, Helen Durand

Chemical Engineering and Materials Science Faculty Research Publications

Image-based control and sensing has been applied in a wide variety of next generation manufacturing fields. Utilizing methods of simulating closed-loop image-based control may be advantageous for improving control performance and design without the need for an experimental setup. One software capable of these simulations is the open-source 3D modeling software Blender, which has many capabilities aided by a Python API. This work explores the use of Blender as an image-based control test bed, where both the process and the controller are simulated, in the context of a greenhouse supplemental lighting control system.

Safety With Non-Deterministic Control Action Selection Using Quantum Devices, Kip Nieman, Helen Durand

Chemical Engineering and Materials Science Faculty Research Publications

Recent increasing interest in quantum computers has spurred research into practical engineering applications for quantum algorithms. One potential application is process control. The unique quantum phenomena involved with quantum computing brings up interesting considerations for control. This work focuses on non-determinism, first through a motivating simulation utilizing a continuous stirred-tank reactor. Following this, two methods of potentially ensuring system stability in the presence of non-determinism are discussed. The first involves including an additional gate to the modified Grover’s algorithm presented in our previous work, which is designed to prevent a qubit state corresponding to an undesired control input from being …

The Use Of Ultraviolet Radiation As A Means Of Destroying Microorganisms In Cherries, Jasur Safarov, Shaxnoza Sultanova, Pulatov M. Murodjon

Chemical Technology, Control and Management

The article discusses methods for extending the shelf life of cherries, having previously treated it with an ultraviolet ray. The article also presents the results obtained, which prove that the shelf life of cherries exposed to ultraviolet increases. At the same time, the article describes in detail the processing technique and presents the results of research.

Study Of Dynamic Characteristics Of The Mechanical Circuit Of The Developed Induction Inertial Vibration Transducer, Sulton Fayzullayevich Amirov, Asror Abdunabiyevich Shoimkulov

Chemical Technology, Control and Management

The article examines the dynamic characteristics of the mechanical circuit of the developed induction vibration transducer. It is found that in the investigated transducers forced oscillations occur with the frequency of the input disturbing force, the amplitude of forced oscillations does not depend on the initial conditions and time, and in forced oscillations with damping there is always a shift of the oscillation phase compared to the phase of the input disturbing force. It is shown that the induction vibration transducer reproduces the measured vibrations with small distortions only in a relatively narrow frequency region at frequencies of the input …

Mathematical Models And Calculation Of Parameters Of Optoelectronic Angular Displacement Converters, Yuriy Gennadyevich Shipulin, Azimjon Khusanov

Chemical Technology, Control and Management

The article discusses promising optoelectronic converters (OP) for wide application of angular movements. A methodology and diagram for calculating OP with the transverse movement of a moving element is presented; in order to simplify the calculation, the weight range of angular movements is conventionally divided into three sub ranges. A graph is given of the dependence of the area of the photosensitive surface of a photo resistor made from a single crystal of high-resistivity p-type silicon.

Improvement Of Calorimetric Quality Analyzers For Substances, Makhfuza Azimovna Radjabova

Chemical Technology, Control and Management

It is noted that the development of intelligent means of measuring qualitative indices is of topical importance. Since the quality of many substances is determined by optical methods, an algorithm for spectrophotometric data processing has been developed, which consists of primary data processing (stage I) and determination of qualitative indices of liquid products (stage II). Since the task of numerical determination of colour characteristics of transmittance coefficients of liquid samples is incorrectly set, it is recommended to use regularization methods of A.N.Tikhonov to improve metrological characteristics of the device. On the basis of regularization methods for solving incorrect problems, algorithms …