Petroleum Engineering Commons^™

Void Fraction Measurements In A Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensors And Pressure Transducers: Effect Of Spargers, Afolabi G. Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

A Critical Review Of Using High Viscosity Friction Reducers As Fracturing Fluids For Hydraulic Fracturing Applications, Mohammed Ba Geri, Abdulmohsin Imqam, Ralph E. Flori

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The primary purpose of using traditional friction reducers in stimulation treatments is to overcome the tubular drag while pumping at high flow rates. Hydraulic fracturing is the main technology used to produce hydrocarbon from extremely low permeability rock. Even though slickwater (water fracturing with few chemical additives) used to be one of the most common fracturing fluids, several concerns are still associated with its use, including usage of freshwater, high-cost operation, and environmental issues. Therefore, current practice in hydraulic fracturing is to use alternative fluid systems that are cost effective and have less environmental impact, such as fluids which utilize …

Investigate The Rheological Behavior Of High Viscosity Friction Reducer Fracture Fluid And Its Impact On Proppant Static Settling Velocity, Mohammed Ba Geri, Abdulmohsin Imqam, Andrey Bogdan, Lingjuan Shen

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The recent and rapid success of using high viscosity friction reducers (HVFRs) in hydraulic fracturing treatments is due to several advantages over other fracture fluids (e.g. linear gel), which include better proppant carrying capability, induce more complex fracture system network with higher fracture length, and overall lower costs due to fewer chemicals and less equipment on location. However, some concerns remain, like how HVFRs rheological properties can have impact on proppant transport into fractures. The objective of this study is to provide a comprehensive understanding of the influence the rheological characterization of HVFRs have on proppant static settling velocity within …

Degradation And Hydrate Phase Equilibria Measurement Methods Of Monoethylene Glycol, Khalid Alef, Stefan Iglauer, Ahmed Barifcani

Research outputs 2014 to 2021

Monoethylene glycol (MEG), a common chemical used for the inhibition of gas hydrate formation may undergo degradation in the regeneration/reclamation process. Limited research exists on the effect of degradation of MEG on hydrate formation, production facilities and equipment especially in the presence of other chemical additives. The proposed method allows for streamlining the process of preparing, degrading and analysis of MEG solutions for hydrate testing and degradation products.

•

Procedure to prepare accurate MEG solutions avoiding oxidative degradation of MEG (i.e., controlling oxygen ingress).

•

Two methods are suggested to mimic field-like degradation of MEG solutions (i.e., degradation by reclamation …

Confirmation Of Data-Driven Reservoir Modeling Using Numerical Reservoir Simulation, Al Hasan Mohamed Al Haifi

Graduate Theses, Dissertations, and Problem Reports (ETD)

Data driven reservoir modeling, also known as Top-Down Model (TDM), is an alternative to the traditional numerical reservoir simulation technique. Data driven reservoir modeling is a new technology that uses artificial intelligence and machine learning to build full-field reservoir models using field measurements (data - facts) instead of mathematical formulations that represent our current understanding of the physics of the fluid flow through porous media. TDM combines all field measurements into a comprehensive reservoir model to predict the production from each well in a field with multiple wells.

There are many opinions, speculations and criticism about not using the physics-based …

Geomechanical Modeling Of Salt Cavern Stability For Carbon Dioxide Storage In The Maha Arakham Formation, Northeastern Thailand, Narumas Pajonpai

Chulalongkorn University Theses and Dissertations (Chula ETD)

In Thailand, CO2 emissions quadrupled over the past three decades since 1989, with the power generation sector as the main contributor by burning fossil fuels to produce electricity. Therefore, the power generating industry has come under scrutiny and been pressed by society to take responsibility. Carbon Capture and Storage (CCS) is one of the many methods to deal with CO2 emissions. Generally, CO2 is captured and stored in geological formations, e.g. rock salt deposits. Salt caverns have been intensively studied regarding their usage for CO2 storage because of their favourable characteristics. In this research, the Finite Element Method (FEM, ANSYS …

การขจัดพอลิไซคลิกแอโรแมติกไฮโดรคาร์บอนในน้ำมันไพโรไลซิสจากยางรถยนต์เหลือทิ้ง, สุรีกาญจน์ กิ่งพุทธพงษ์

Chulalongkorn University Theses and Dissertations (Chula ETD)

น้ำมันที่ได้จากการไพโรไลซิสยางรถยนต์เหลือทิ้ง (waste tire pyrolysis oil, WTPO) ประกอบไปด้วยสารประกอบพอลิไซคลิกแอโรมาติกส์ไฮโดรคาร์บอน (polycyclic aromatic hydrocarbon, PAHs) ประมาณ 10% โดยน้ำหนักเมื่อเทียบกับปริมาณ WTPO โดย PAHs ที่พบมากที่สุด คือ แนฟทาลีน ซึ่งมีความเป็นพิษต่อมนุษย์และสิ่งแวดล้อม นี่จึงเป็นข้อจำกัดที่ทำให้ไม่สามารถนำ WTPO ไปใช้ในเครื่องยนต์ได้ ในงานวิจัยนี้จึงศึกษาการกำจัดแนฟทาลีนซึ่งเป็นแบบจำลองของ PAHs ผ่านกระบวนการไฮโดรจิเนชัน โดยใช้ตัวเร่งปฏิกิริยานิกเกิลบนตัวรองรับแกมมาอะลูมินา (Ni/γ-Al2O3) ที่มีและไม่มีตัวสนับสนุนโมลิบดินัม (Mo) ทังเสตน (W) หรือ แพลตินัม (Pt) สำหรับภาวะที่ศึกษาในการไฮโดรจิเนชัน ได้แก่ ความดันแก๊สไฮโดรเจนเริ่มต้น (10-40 บาร์) อุณหภูมิ (250-400 องศาเซลเซียส) และระยะเวลาในการทำปฏิกิริยา (2-8 ชม.) ก่อนทำปฏิกิริยาตัวเร่งปฏิกิริยาถูกรีดักชัน (reduction) แบบอิน-ซิทู (in-situ) ที่ความดันแก๊สไฮโดรเจนเริ่มต้น 30 บาร์ อุณหภูมิ 400 องศาเซลเซียส เป็นเวลา 2 ชม. ในกรณีที่ไม่มีตัวสนับสนุน Ni ปริมาณ 1-30% โดยน้ำหนักเมื่อเทียบกับตัวรองรับถูกเตรียมลงบน γ-Al2O3 ที่ถูกเตรียมด้วยวิธีไฮโดรเทอร์มัล และค่าการเปลี่ยนแปลงแนฟทาลีนถูกวิเคราะห์ด้วยแก๊สโครมาโทกราฟี ตัวตรวจวัดชนิดเฟลมไอออไนเซชัน (GC-FID) พบว่าเมื่อใช้ตัวเร่งปฏิกิริยาที่มีปริมาณ Ni 20% โดยน้ำหนักเมื่อเทียบกับตัวรองรับให้ค่าการเปลี่ยนแปลงแนฟทาลีนสูงสุดที่ 29.5% โดยภาวะที่ใช้ คือความดันไฮโดรเจนเริ่มต้น 30 บาร์ อุณหภูมิ 350 องศาเซลเซียส นาน 4 ชั่วโมง ในกรณีมีตัวสนับสนุน ตัวเร่งปฏิกิริยา NiMo NiW และ NiPt ให้ค่าการเปลี่ยนแปลงแนฟทาลีนสูงสุดที่ 44.7 46.4 และ 55.8% เมื่ออัตราส่วนเชิงอะตอมของตัวสนับสนุนเป็น 0.27 0.05 และ …

Investigating The Use Of Different Types Of Sealant Materials For Cement Remedial Applications, Murad Mohammedahmed Abdulfarraj

Doctoral Dissertations

"The overall objective is to investigate the ability of several material to mitigate cement failures such as channels, fractures, and micro-annuli in oil and gas wells. The sealant material that can also be used in the wells that are used for geologic storage of carbon dioxide CO₂. Evaluating the sealant material is critical to improve the zonal isolation of the wells, which would lead to safer operations. The approach of this dissertation is to utilize particles gel that has been used successfully in conformance control application, and epoxy resin systems, that have superior seal characteristics compared to conventional …

Asphaltene Stability In Crude Oil During Carbon Dioxide Injection And Its Impact On Oil Recovery: A Review, Data Analysis, And Experimental Study, Sherif M. Fakher

Masters Theses

"Crude oils are usually associated with many compounds, some of which are favorable and others, which are not. One of the most unfavorable components of crude oil that pose severe operational problems and decreases oil production significantly are asphaltenes. These compounds are solids that are homogenized in the crude oil at room temperature but tend to separate from solution when agitated. They can deposit in the reservoir pores, wellbore, and transportation pipelines thus causing severe operational problems and oil recovery reduction.

Even though researchers have been studying asphaltenes for more than 100 years, there is still an ambiguity concerning asphaltene …

Investigating The Use Of Class C Flyash-Based Geopolymer Cement As A Potential Alternative To Portland Cement To Seal Co₂ Storage Wells, Priyesh Parimal Jani

Masters Theses

"Capturing emitted carbon dioxide from the source of emission and storing it underground is one effective way to reduce the amount of CO₂ in the atmosphere and is called carbon capture and storage (CCS). For the successful CCS project, it is necessary to ensure long term storage of injected CO₂ inside these selected reservoirs. Portland cement used to cast wells in these reservoirs degrade in CO₂ environment and can create migration path for leakage of CO₂. The aim of this study was to provide a comprehensive review about the problem, to propose a new geopolymer …

Computational Fluid Dynamics Modeling Of Proppant Static Settling Velocity In High Viscosity Friction Reducers, Chen Yuan

Masters Theses

"In the current petroleum fracturing industry, it is necessary to understand the downhole migration and settling velocity of the proppant. If we can master this information well, it will be a great help to obtain effective propped fracture conductivity. In order to study the transport of proppants in the well, we used laboratory experiments and computer numerical simulations to compare the results to get a meaningful conclusion. We spent a lot of time building models on a powerful computer and comparing the experimental conclusions. We finally decided to use computational fluid dynamics (CFD) as the simulation platform, discrete phase method …

Modeling Overpressure Development During Shale Rock Compaction Coupling Poroelasticity And Permeability Evolution Above 3km Depth, Wenyu Zhao

Masters Theses

"The evolution of pore pressure including overpressure during sedimentation is an important process to consider when analyzing whether high pore pressure causes rock failure. High pore pressure is caused by under-compaction due to the rapid burial of low-permeability sediments, and as a result, porosity decreases less rapidly with depth than in normally compacted sediments where porosity decreases exponentially with depth. While under-compaction related pore pressure magnitudes have been determined empirically, in most numerical modeling approaches, the pore pressure is either applied as a static magnitude or coupled to a fluid flow simulator. This study simulates the pore pressure evolution during …

Gel Composition And Brine Concentration Effect On Hydrogel Dehydration Subjected To Uniaxial Compression, Xinrui Zhao

Masters Theses

"Gel treatment is a process that injects the gel into a reservoir to control the conformance and improve the sweep efficiency of injection fluids. At a certain pressure gradient, the gel dehydrates in a reservoir due to mechanical forces. This work evaluates the effects of the gel composition and brine concentration on gel dehydration under uniaxial compression. A sodium acrylate-co-acrylamide based gel cross-linked with N, N'-Methylenebisacrylamide (MBAA) was used for the study. The compression test is performed with a rheometer with a plate-plate geometry. The gel dehydration under pressure was measured to see how gel dehydration would be impacted by …

Breaker Evaluation And Formation Damage Remediation Of Re-Crosslinkable Preformed Particle Gel (Rppg), Enze Zhou

Masters Theses

"Re-crosslinkable preformed particle gel (RPPG) is a newly developed preformed particle gel for improving sweep efficiency and oil recovery by blocking or reducing the conductivity of fractures and fracture-like channels or conduits. However, RPPG has the potential to plug the facilities or damage the formation if a treatment is not properly conducted.

This work presents the performance of selected oxidizing breakers on the degradation of RPPG. The influence of a few factors on the degradation process was investigated, including breaker type, breaker concentration, temperature, gel concentration, gel aging time, and gel size. Results indicate that breaker type, concentration, and temperature …

Review And Data Analysis Of Low Salinity Water Effect Through Induced Fine Migration, Dawei Xu

Masters Theses

"Low salinity water flooding (LSWF) is well proved to be an effective EOR technology both in laboratory and field tests, however, the conditions for LSWF to work and EOR mechanism is still debatable. Up till now, many mechanisms have been proposed to explain the incremental oil recovery in sandstone by LSWF, for instance, fine migration, ionic exchange, wettability alteration and pH increase.

In this study, we only focus on low salinity water flooding effect through induced fine migration mechanism. The objective of this study is to conduct a comprehensive analysis using statistical analysis methods and explaining the mechanism of fine …

Gas Hold-Up Measurements In 0.3 M Diameter Bubble Column: Effect Of Electrolytes, Heber Blanco De Brand

Dissertations and Theses

The present work reports the axial, radial and temporal gas hold-up profiles in a 0.3 m diameter batch bubble column using a pair of Wire Mesh Sensors and six pressure transducers.

The Mixed Integer Non-Linear Programming For Combined Heat And Mass Exchanger Network Synthesis With The Effect Of Emcd And Emat On Economic Analysis, Eleonora Amelia

Chulalongkorn University Theses and Dissertations (Chula ETD)

The Combined Heat and Mass Exchanger Network Synthesis (CHAMENS) which comprised a win-win strategy simultaneously diminishing the emission alongside maximizing the profits of the whole systems has been accomplished in this work. The novelty comes from the development of the original stage-wise superstructure (SWS) to be able to overcome the problems including detailed cost considerations by using more accurate formularies to determine the exchanger configurations, initializations, favorable boundaries to solve the complexities, eradicate the number of the heat and mass exchangers, and decrease the TAC. The purpose of this work is generate the new applicable method which is noticeable and …

Pre-Feasibility Study Of Improving Quality Of Low-Grade Fluorite. A Case Study At Phanomthuan Deposit, Kanchanaburi, Thailand, Keosaychai Souvannavong

Chulalongkorn University Theses and Dissertations (Chula ETD)

In this study was presented the pre-feasibility study of improving quality of low-grade fluorite from Phanomthuan deposit, Kanchanaburi province, Thailand. The purpose of this study aims to explore the optimal condition in order to remove the impurities which contained high SiO2, CaCO3 and other minerals, also evaluate the project in term of economic. Therefore, the improvement quality of fluorite by using froth flotation techniques was reach the ceramic grade. The raw material characterization contains CaF2 = 29.4 Wt.%, SiO2 = 43.9 Wt.% and CaCO3 = 6.9 Wt.%. After flotation process the optimal condition result which contains CaF2 = 96.46 Wt.%, …

Transient Multiphase Flow Simulation For Unloading Of Frac Hit Gas Wells, Miguel Angel Cedeno Moreno

Doctoral Dissertations

"This work seeks to develop a fully step-by-step transient multiphase flow simulation valid for unloading gas wells using nitrogen. It studies the behavior of nitrogen for unloading horizontal gas wells with gas injection in the annulus. The work investigates unloading non-Newtonian fluids such as those which invade offset wells when a frac hit occurs during hydraulic fracturing operations in unconventional wells. The effect of varying tubing depth and injection pressure are included in the study.

Results show that as the plastic viscosity increases, the nitrogen volume and time to unload will be increased. As tubing depth increases, the nitrogen volume …

Plugging Performance Of Preformed Particle Gels In Fractures And Its Influencing Factors, Ze Wang

Doctoral Dissertations

"Preformed particle gels (PPG) has been successfully applied to combat the water channeling caused by fractures or fracture-like channels. Understanding the placement and plugging of PPG in fractures is crucial for gel treatment design. The objective of the dissertation is to explore the plugging performance of three PPG products in two types of fracture models, the partially and fully open fractures. The following studies has been conducted and conclusions have been drawn based on the results and analysis. First, the placement and plugging performance of conventional PPG was investigated using core flooding experiments conducted partially open fractures. The plugging efficiency …