Chemical Engineering Commons^™

Endoscopic Application Of A Compact Compound-Eye Camera, Keiichiro Kagawa, Shoji Kawahito

Makara Journal of Technology

A multi-functional compound-eye endoscope enabling multi-spectral imaging and variable field-of-view is presented, which is based on a compact compound-eye camera called TOMBO (thin observation module by bound optics). Narrow-band filters attached to some lenses provide snap-shot multi-band images. Fixed and movable mirrors are introduced to control the field of view, which realizes several observation modes such as three-dimensional shape measurement, wide field-of-view, and close-up observation.

Lateral Load Resistance Of Laminated Veneer Lumber Sengonwooden Joints With Wooden Dowels, Niken Palaeowati, Ali Awaludin, Suprapto Siswosukarto

Makara Journal of Technology

Analytical models for wooden-doweled joints need to be developed. The objective of this research is to determine whether the strength of wooden-doweled joints can be well predicted by equations developed for steel-doweled joints. In this experiment, various connection parameters, such as dowel diameter, species of the wooden dowel, and angle of joints, are studied. The joint specimens are loaded in a quasi-static state with four replications each. A5% offset diameter method is used to determine the lateral load resistance of the tested joints, while the predictions are evaluated by equations given in Indonesian National Standard (SNI) 7973-2013 and the European …

Processing And Mechanical Testing Of Strontium-Substituted Hydroxyapatite/Glass Composites, Chokchai Yatongchai, Mark R. Towler, Anthony W. Wren

Chemical and Biochemical Engineering Faculty Research & Creative Works

Sr-HA/Glass composites were produced. Phase composition of composites was evaluated. Their physical and mechanical properties were determined. Sintered composites mainly consisted of Sr-HA/β-TCP, or β-TCP/Ca₂ZnSi₂O₇. The composites had porosity up to 4 times those of undoped Sr-HA. Compared to undoped Sr-HA, the Sr-HA/Glass composites had lower biaxial flexural strength and hardness. The Weibull modulus for the composites ranged from 2.77 to 18.74.

Fabrication Of A Thin Silver Nanowire Composite Film And Investigation Of A Patterning Technique., Richard S. Korte 1991-

Electronic Theses and Dissertations

Electrically conductive polymers encompass an exciting field of research for applications in dye-sensitized solar cells (DSSC’s). DSSC’s possess several advantages over other types of solar cells. They offer the potential for high quantum efficiency, solar conversion efficiency approaching that of traditional silicon panels, rapid charge transfer kinetics for photo-excited electrons, mechanical flexibility, and cost efficient manufacturing processes. However, key drawbacks to their large scale production and performance lifetime lie in their reliance on costly indium tin oxide (ITO), fluorinated tin oxide (FTO), and platinum for electrode materials, and the mechanical fragility inherent to a liquid electrolyte layer component. Much of …

Photobioreactor Design For Improved Energy Efficiency Of Microalgae Production, Alexander Burns

Master's Theses

ABSTRACT

Photobioreactor Design for Improved Energy Efficiency of Microalgae Production

Alexander Burns

The objective of this research was to investigate a new photobioreactor (PBR) design for microalgae production that retains the typical advantages of existing tubular PBRs while reducing power consumption by providing simultaneous culture circulation and gas exchange with airlift alone and no centrifugal recirculating pump. Traditional tubular PBR designs feature a compressed air supply and a centrifugal pump for culture circulation and gas exchange. Circulation and gas exchange in a closed-system PBR is necessary to keep the algae suspended and to provide sufficient mass transfer (mainly for the …

Recycling Wastewater For Hydraulic Fracturing By Use Of Nanofiltration Membranes, Haley D. Cleous

Chemical Engineering Undergraduate Honors Theses

Hydraulic fracturing creates large volumes of produced water, contaminated with organics, suspended solids, and dissolved minerals. This water must either be disposed of in injection wells or treated for reuse. One option is to use a combination of ultrafiltration and nanofiltration to treat this water and reuse it in future hydraulic fracturing wells. The object of this study was to test and characterize commercial nanofiltration membranes. The work done for this project will lead to future work in modifying membranes to improve the rejection of desired components.

Substrate Concentration Influences Effective Radial Diffusion Coefficient In Canine Cortical Bone, Kurt Farrell, Daniel O’Conor, Mariela Gonzalez, Caroline Androjna, Ronald J. Midura, Surendra N. Tewari, Joanne M. Belovich

Chemical & Biomedical Engineering Faculty Publications

Transport of nutrients and waste across osseous tissue is dependent on the dynamic micro and macrostructure of the tissue; however little quantitative data exists examining how this transport occurs across the entire tissue. Here we investigate in vitro radial diffusion across a section of canine tissue, at dimensions of several hundred microns to millimeters, specifically between several osteons connected through a porous microstructure of Volkmann's canals and canaliculi. The effective diffusion coefficient is measured by a "sample immersion" technique presented here, in which the tissue sample was immersed in solution for 18-30 h, image analysis software was used to quantify …

Microanalysis Of Polymer Chain Diffusion In Heat Seals, Russell Cooper

All Theses

Heat sealing is an integral method for the closure and protection of packaging. Previous work has shown that seal strength is developed by the interdiffusion of polymer chains within heat seals. Heat seals were made between two dissimilar materials. Poly(ethylene-co-acrylic acid) (EAA) was heat sealed to ionomer. Diffusion within the EAA-ionomer heat seals was estimated. The diffusion estimates were then related to resulting seal strength in the EAA-ionomer sealant system. Heated tooling sealing was utilized to make heat seals at 40 psi (275.79 kPa), 0.5 seconds, and a range of temperatures between 180˚F (82.22˚C) and 300˚F (148.89˚C). Scanning electron microscopy …

Designing Magnetically Responsive Ultrafiltration Membranes, Robert William Dong

Graduate Theses and Dissertations

Ultrafiltration (UF) membranes developed out of a need for protein separation processes. Currently, they are used in a variety of industries ranging from food manufacturing to pharmaceuticals for two main purposes: concentration, separation, and buffer exchange. UF membrane processes in product streams undergo frequent use and like all membrane processes experience a gradual decline in performance due to fouling phenomena both irreversible and reversible. Ultimately, performance declines to a point where the UF membrane needs to be replaced. Frequent replacement of UF membranes is detrimental to major industries that require high product throughput using UF processes. Thus, it is important …

Printing Functional Electronic Circuits And Components, Ahmed Tausif Aijazi

Dissertations

The purpose of this study was to investigate the challenges in printing reliable multilayer flexible circuits, devices and components. Gravure was used as the primary printing process for this work, but due to some limitations of gravure, other printing methods were also investigated. At first a systematic study was done to determine the optimum parameters for the gravure printing of sub 50 micron lines. Commercially available silver nanoparticle inks were printed on a lab scale gravure printer, Accupress®. The highest resolution line that was electrically conductive was 36μm wide. The 9μm, 18μm and 27μm lines were printed but were not …

Kinetic Experimental And Modeling Studies On Iron-Based Catalysts Promoted With Lanthana For The High-Temperature Water-Gas Shift Reaction Characterized With Operando Uv-Visible Spectroscopy And For The Fischer-Tropsch Synthesis, Basseem Bishara Hallac

Theses and Dissertations

The structural and functional roles of lanthana in unsupported iron-based catalysts for the high-temperature water-gas shift reaction and Fischer-Tropsch synthesis were investigated. The performance of the catalysts with varying lanthana contents was based on their activity, selectivity, and stability. With regard to the former reaction, extent of reduction of the iron in Fe2O3/Cr2O3/CuO/La2O3 water-gas shift catalysts is a key parameter that was characterized using UV-visible spectroscopy. Minor addition of lanthana (<0.5 wt%) produces more active and stable catalysts apparently because it stabilizes the iron-chromium spinel, increases the surface area of the reduced catalysts, enhances the reduction of hematite to the magnetite active phase, and facilitates the adsorption of CO on the surface of the catalyst modeled by an adsorptive Langmuir-Hinshelwood mechanism. Statistical 95% confidence contour plots of the adsorption equilibrium constants show that water adsorbs more strongly than CO, which inhibits the reaction rate. A calibration curve that correlates the oxidation state of surface iron domains to normalized absorbance of visible light was successfully generated and applied to the water-gas shift catalysts. UV-visible studies indicated higher extent of reduction for surface Fe domains for the catalysts promoted with 1 wt% of lanthana and showed potential to be a more convenient technique for surface chemistry studies than X-ray absorption near edge spectroscopy (XANES). Lanthana addition to iron-based Fischer-Tropsch catalysts enhances the olefin-to-paraffin ratio, but decreases their activity, stability, and selectivity to liquid hydrocarbons. Adding lanthana at the expense of potassium reduces the water-gas shift selectivity and enhances the activity and stability of the catalysts. Finally, a model that simulates heat and mass transfer limitations on the particle scale for the Fischer-Tropsch reaction applicable at lab-scale suggests optimal operating and design conditions of 256°C, 30 bar, and 80 mirons are recommended for higher selectivity to liquid hydrocarbons. The model considers pressure drop, deactivation, pore diffusion, film heat transfer, and internal heat transfer when solving for the optimal conditions, and maps them as functions of design variables. This model can be up-scaled to provide guidance for optimal design of commercial-size reactors.

Lntegration Of Conventional Lithography And Printing Processes As A Key Enabling Technology For Printed And Flexible Sensing Systems, Binu Baby Narakathu

Dissertations

Sensors, which are used ubiquitously in a wide variety of applications, are revolutionizing the already ever-changing world we live in by providing real-time information about our surroundings. This dissertation focuses on the integration of conventional photolithography and printing processes as a key enabling technology for printed and flexible sensing systems.

Initially, an efficient opto-electrochemical sensing system, for the dual detection of heavy metal compounds was successfully developed. A novel microfluidic flow cell, with a reservoir volume of 25 μl, was designed and fabricated using acrylic. An electrochemical sensor with gold (Au) interdigitated electrodes (IDE) on a glass substrate was photolithographically …

Using Greet To Analyze Natural Gas Usage In Municipal Fleets, Bradley E. Gibson

Honors Theses

GREET was used to calculate energy consumption and pollutants emitted from specific fuel/vehicle types when given a specific set of parameters. In this case, the parameters were the type of fuel mix from TVA, the selected vehicle year of 2015, the vehicle weight specified in the heavy-duty vehicle range, and type of simulation technique, which was the Hammersely Sequence Sampling. These inputs, along with seventeen fuel/vehicles mixes, specific pollutants, and cost considerations, were used to investigate the environmental impact of the transition from petrol diesel to natural gas in the municipal fleets of Chattanooga, Tennessee. The energy consumption included coal, …

Water System For Developing Countries / Disaster Relief Made With Local Materials, Shumon Hasan

Chemistry & Biochemistry Undergraduate Honors Theses

The objective of this project was to design a water purification system that can be constructed from easily available materials, common to the particular country, and is capable of the complete water purification process.

Optimized Photogrammetric Network Design With Flight Path Planner For Uav-Based Terrain Surveillance, Ivan Yair Rojas

Theses and Dissertations

This work demonstrates the use of genetic algorithms as a stochastic optimization technique for developing a camera network design and the flight path for photogrammetricapplications using Small Unmanned Aerial Vehicles. This study develops a Virtual Optimizer for Aerial Routes (VOAR) as a new photogrammetric mapping tool for acquisition of images to be used in 3D reconstruction. 3D point cloud models provide detailed information on infrastructure from places where human access may be difficult. This algorithm allows optimized flight paths to monitor infrastructure using GPS coordinates and optimized camera poses ensuring that the set of images captured is improved for 3D …

Solar Brine Concentrator, Aric Gregory Fisher

Chemical Engineering Undergraduate Honors Theses

In arid regions of the United States potable water is a valuable resource and is sometimes produced using energy intensive processes by removing salts from brackish water. Task 4 provides a solar option for producing potable water from brackish water; in competing in Task 4, H2OGS has developed a simple, cost effective solar desalination process to provide these regions with necessary, potable water. H2OGS’ design takes into account WERC requirements, including cost, energy usage, worker safety, and easily obtained materials. U.S. government regulatory requirements are also taken into account as the proposed location for this process is Alamogordo, New Mexico. …

Werc: Solar Brine Concentrator, Sarah K. Haley

Chemical Engineering Undergraduate Honors Theses

In arid regions of the United States potable water is a valuable resource and is sometimes produced using energy intensive processes by removing salts from brackish water. Task 4 provides a solar option for producing potable water from brackish water; in competing in Task 4, H2OGS has developed a simple, cost effective solar desalination process to provide these regions with necessary, potable water. H2OGS’ design takes into account WERC requirements, including cost, energy usage, worker safety, and easily obtained materials. U.S. government regulatory requirements are also taken into account as the proposed location for this process is Alamogordo, New Mexico. …

Simultaneous Conversion Of All Cell Wall Components By Oleaginous Fungus Without Chemi-Physical Pretreatment, Shangxian Xie, Xin Qin, Yanbing Cheng, Dhrubojyoti Laskar, Weichuan Qiao, Su Sun, Luis Reyes, Xin Wang, Susan Dai, Scott Sattler, Katy Kao, Bin Yang, Xiaoyu Zhang, Joshua Yuan

Faculty Publications

Lignin utilization during biomass conversion has been a major challenge for lignocellulosic biofuel. In particular, the conversion of lignin along with carbohydrate for fungible fuels and chemicals will both improve the overall carbon efficiency and reduce the need for chemical pretreatments. However, few biomass-converting microorganisms have the capacity to degrade all cell wall components including lignin, cellulose, and hemicellulose. We hereby evaluated a unique oleaginous fungus strain, Cunninghamella echinulata FR3, for its capacity to degrade lignin during biomass conversion to lipid, and the potential to carry out consolidated fermentation without chemical pretreatment, especially when combined with sorghum (Sorghum bicolor) bmr …

Low Molecular Weight Glucosamine/L-Lactide Copolymers As Potential Carriers For The Development Of A Sustained Rifampicin Release System: Mycobacterium Smegmatis As A Tuberculosis Model, Jorge Ragusa

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

Tuberculosis, a highly contagious disease, ranks as the second leading cause of death from an infectious disease, and remains a major global health problem. In 2013, 9 million new cases were diagnosed and 1.5 million people died worldwide from tuberculosis. This dissertation aims at developing a new, ultrafine particle-based efficient antibiotic delivery system for the treatment of tuberculosis. The carrier material to make the rifampicin (RIF)-loaded particles is a low molecular weight star-shaped polymer produced from glucosamine (molecular core building unit) and L-lactide (GluN-LLA). Stable particles with a very high 50% drug loading capacity were made via electrohydrodynamic atomization. Prolonged …

Phase Transformation Studies Of Metal Oxides To Dichalcogenides In 1-D Structures., Dustin Ray Cummins 1987-

Electronic Theses and Dissertations

Recently, the use of materials with nanoscale morphologies has expanded, particularly with applications in energy conversion, catalysis, and energy storage. One drawback to single crystalline nanomaterials, especially 1D nanowires, is the difficulty in synthesizing these compounds, as the material chemistry becomes more complicated. Metal oxide nanowires can be synthesized easily and can be produced in relatively large quantities. However, more complex materials, such as metal chalcogenides, cannot typically be synthesized using facile methods, and currently very few techniques involve scalable methods. Phase transformation of metal oxides nanowires to form metal sulfides and selenides by gas-solid reactions is one viable route …