Materials Chemistry Commons^™

A Spin-Coated Tiox/Pt Nanolayered Anodic Catalyst For The Direct Formic Acid Fuel Cells, Islam M. Al-Akraa, Ahmad M. Mohammad Prof

Chemical Engineering

The CO poisoning of the platinum anodic catalyst which typically functions the catalytic deterioration of the direct formic acid fuel cells could be minimized with a simple modification for Pt with titanium oxide. The fabrication scheme involved the spin-coating of a Ti precursor onto a Pt thin layer that was physically sputtered onto a Si substrate. The whole assembly was subjected to a post-annealing processing to produce the TiOx layer (60 nm) in a porous structure (mostly Anatase) atop of the Pt surface. The porous nature of the TiOx layer permitted the participation of Pt in the electrocatalysis of the …

Development Of Supported Pd-Based Catalysts For Carbon-Carbon Cross-Coupling And Oxidation Reactions, Mrinmoy Das

Theses and Dissertations

Heterogeneous catalysts are a crucial part of chemistry used for various chemical synthesis stages, pharmaceutical, and environmental applications. The use of nanoparticles or rather nanocatalysts enhances the heterogeneous catalytic applications. Both chemical and physical methods can be used to synthesize nanocatalysts. Chemical synthesis methods require comparatively fewer instruments and can easily synthesize a large amount of nanocatalysts. Nevertheless, chemical synthesis methods require reducing agents and solvents that can be toxic or harmful materials. They often need harsh reaction conditions as well, like high temperature and pressure. On the other hand, physical synthesis methods often require complex instrument setup, but their …

Tetrathiafulvalene: A Gate To The Mechanochemical Mechanisms Of Electron Transfer Reactions, Richard Chen, Mehmet Kerem Gokus, Silvina Pagola

Chemistry & Biochemistry Faculty Publications

This report describes aspects of our previous studies of the mechanochemical synthesis of charge transfer complexes of the electron donor tetrathiafulvalene, which are relevant to the use of laboratory X-ray powder diffraction for ex situ monitoring of mechanochemical reactions toward investigating their mechanisms. In particular, the reaction of tetrathiafulvalene and chloranil was studied under neat mechanochemical conditions and liquid-assisted grinding with diethyl ether (1 μL/mg). The product in both cases is the green tetrathiafulvalene chloranil polymorph and the mechanism of the redox reaction is presumably the same. However, while the kinetic profile of the neat mechanochemical synthesis was fitted with …

Correlating The Physicochemical Properties Of Magnesium Stearate With Tablet Dissolution And Lubrication, Julie L. Calahan

Theses and Dissertations--Pharmacy

Magnesium stearate (MgSt) is the most commonly used pharmaceutical excipient and is present in over half the tablet formulations on the market. In spite of its popularity as an effective lubricant, it has been repeatedly recognized that there is significant variability between MgSt samples, which can cause inconsistent lubrication between batches of MgSt. The hypothesis of this research is that the batch-to-batch variability in tablet lubrication and dissolution observed in tablet formulations containing different MgSt samples can be correlated with differences in MgSt physicochemical properties (fatty acid salt composition, crystal hydrate form, particle size and surface area). Developing correlations between …

Carbon Oxidation At The Atomic Level: A Computational Study On Oxidative Graphene Etching And Pitting Of Graphitic Carbon Surfaces, Simon Schmitt

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to understand the oxidation of solid carbon materials by oxygen-containing gases, carbon oxidation has to be studied on the atomic level where the surface reactions occur. Graphene and graphite are etched by oxygen to form characteristic pits that are scattered across the material surface, and pitting in turn leads to microstructural changes that determine the macroscopic oxidation behavior. While this is a well-documented phenomenon, it is heretofore poorly understood due to the notorious difficulty of experiments and a lack of comprehensive computational studies. The main objective of the present work is the development of a computational framework from …

Singlet Fission In A Hexacene Dimer: Energetics Dictate Dynamics, Samuel N. Sanders, Elango Kumarasamy, Kealan J. Fallon, Matthew Y. Sfeir, Luis M. Campos

Publications and Research

Singlet fission (SF) is an exciton multiplication process with the potential to raise the efficiency limit of single junction solar cells from 33% to up to 45%. Most chromophores generally undergo SF as solid-state crystals. However, when such molecules are covalently coupled, the dimers can be used as model systems to study fundamental photophysical dynamics where a singlet exciton splits into two triplet excitons within individual molecules. Here we report the synthesis and photophysical characterization of singlet fission of a hexacene dimer. Comparing the hexacene dimer to analogous tetracene and pentacene dimers reveals that excess exoergicity slows down singlet fission, …

Gravity-Drawing Flexible Silicone Filaments As Fiber Optics And Model Foldamers, Katherine Snell

CMC Senior Theses

Here, we present a method of gravity-drawing polydimethylsiloxane (PDMS) silicone fibers with application as fiber optics and as model foldamers. Beginning as a viscous liquid, PDMS is cured using heat until its measured viscosity reaches 4000 mPa•s. The semi-cured elastomer is then extruded through a tube furnace to produce thin (diameters on the order of hundred micrometers) filaments with scalable lengths. PDMS is biocompatible, gas-permeable, flexible, and hydrophobic. Additionally, the PDMS surface hydrophobicity can be modified via UV exposure, O2 plasma, and corona discharge. We demonstrate the patternibility (i.e patterns of hydrophobicity) of PDMS fibers, adding complexity to potential foldamer …

Fabrication Of A 3d Printed Porous Junction For Ag|Agcl|Gel-Kcl Reference Electrode, Sarah May Sibug-Torres, Lance P. Go, Erwin Enriquez

Chemistry Faculty Publications

Fused filament fabrication (FFF) is a 3D printing method that is attracting increased interest in the development of miniaturized electrochemical sensor systems due to its versatility, low cost, reproducibility, and capability for rapid prototyping. A key component of miniaturized electrochemical systems is the reference electrode (RE). However, reports of the fabrication of a true 3D-printed RE that exhibits stability to variations in the sample matrix remain limited. In this work, we report the development and characterization of a 3D-printed Ag|AgCl|gel-KCl reference electrode (3D-RE). The RE was constructed using a Ag|AgCl wire and agar-KCl layer housed in a watertight 3D-printed acrylonitrile …

Cu(Ii) Phenanthroline-Phenazine Complexes Dysregulate Mitochondrial Function And Stimulate Apoptosis, Garret Rochford, Zara Molphy, Kevin Kavanagh, Malachy Mccann, Michael Devereux, Andrew Kellett, Orla L. Howe

Articles

Herein we report an in-depth study on the cytotoxic mechanism of action of four developmental cytotoxic copper(II) complexes: [Cu(phen)2]2+ (Cu-Phen); [Cu(DPQ)(Phen)]2+ (Cu-DPQ-Phen); [Cu(DPPZ)(Phen)]2+; and [Cu(DPPN)(Phen)]2+ (where Phen = 1,10-phenanthroline, DPQ = dipyrido[3,2-f:20,30-h]quinoxaline, DPPZ = dipyrido[3,2-a:20,30-c]phenazine, and DPPN = benzo[i]dipyrido[3,2-a:20,30-c]phenazine). This complex class is known for its DNA intercalative properties and recent evidence—derived from an in vivo proteomic study—supports the potential targeting of mitochondrial function. Therefore, we focused on mitochondrial-mediated apoptosis related to cytotoxic activity and the potential impact these agents have on mitochondrial function. The Cu(II) complexes demonstrated superior activity regardless of aromatic extension within the phenazine ligand to the …

Synthesis Of Graphene Using Plasma Etching And Atmospheric Pressure Annealing: Process And Sensor Development, Andrew Robert Graves

Graduate Theses, Dissertations, and Problem Reports (ETD)

Having been theorized in 1947, it was not until 2004 that graphene was first isolated. In the years since its isolation, graphene has been the subject of intense, world-wide study due to its incredibly diverse array of useful properties. Even though many billions of dollars have been spent on its development, graphene has yet to break out of the laboratory and penetrate mainstream industrial applications markets. This is because graphene faces a ‘grand challenge.’ Simply put, there is currently no method of manufacturing high-quality graphene on the industrial scale. This grand challenge looms particularly large for electronic applications where the …

Design Of Pigments For Use In “Cool” Coatings, Tyler Laughorn

Williams Honors College, Honors Research Projects

This project was focused on the development and testing of several novel pigments that exhibit high NIR-reflectance and therefore show potential for use in “cool” coatings. A “cool” coating will reflect more solar radiation than other standard coatings, and so a coated structure would require less energy to keep cool. Four sets of pigments were synthesized: Co_1-xMg_xCr₂O₄ (teal), Co_0.25Mg_0.75Cr_2-yAl_yO₄ (blue), Ti_1-x-yNi_xSb_yO₂ (yellow), and Cr_2-xFe_xO₃ (black). NIR and TSR values were then measured …

Filtration Apparatus Design For Oil-Water Separation Using Membranes And Sponges, Alec Jerger

Williams Honors College, Honors Research Projects

It can be difficult to separate water and oil emulsions through traditional filtration. Therefore, investigations of filtering using thermo-responsive (TR) polymers, in this case poly(vinyl methyl ether) (PVME), was conducted. It’s hypothesized that below its lower critical solution temperature (LCST), PVME has an affinity for water while oil substances do not. Above the LCST the opposite will be true. To verify this hypothesis, iterations of filtration designs were created to provide optimum control over the parameters to measure flow. The final optimized experimental apparatus was a Chromaflex glass column which was air tight and controlled all parameters besides fluid flow. …

Sugar-Derived Oleogels In Cosmetics And Food Applications: A Case Study Of Trehalose- And Mannitol-Based Gelators, Polina Tsupko

Dissertations and Theses

Gels represent an indispensable part of our everyday lives with direct applications in food, medicine, cosmetics and other industries. Amphiphilic molecules have been shown to act as low molecular weight gelators (LMWGs) and are becoming the main focus of several research groups. Their ability to self-assemble into various morphologies from micelles to bilayer sheets, and remain stable due to noncovalent forces responsible for the formation of the 3D network—Self-Assembled Fibrillar Network (SAFiNs)—is in the core of their ability to produce molecular gels. Those amphiphilic molecules capable of adsorbing at the interface and behaving as surface active agents are known as …

Metal-Oxide Nanostructures Fabricated From Reactive Laser Ablation In Liquid, Mallory G. John

Theses and Dissertations

The development of metal-oxide nanostructures is a growing area due to their applications in diverse fields spanning energy conversion and storage, chemical manufacturing, and en- vironmental technology. This interest in catalytically active nanomaterials has prompted the synthesis and investigation of highly functionalized nanoparticles (NPs), including core- shell, silicate-stabilized, and bi- and multi-metallic nanocomposites. While wet-chemical synthesis methods of metal-oxide nanostructures have led to several morphologies, compositions, and shapes, these syntheses often require high temperatures, toxic solvents or reducing agents, and long reaction times.

Laser synthesis and processing of colloids (LSPC) encompasses both ‘top down’ and ‘bottom up’ approaches to synthesize …

Redox-Active Porous Organic Materials For Electrochemical Energy Storage Applications, K. Shamara Weeraratne

Theses and Dissertations

As the demand for renewable energy technologies grows, so does the need for cheaper, more efficient rechargeable batteries to store the energy. While lithium-ion battery (LIBs) technology is well established, it suffers from limited lithium supplies. Furthermore, the highly toxic transition metals used in the electrodes places a huge burden on the environment. Therefore, replacing lithium with more economical sodium metal in rechargeable batteries (i.e. sodium-ion batteries, SIBs) has garnered considerable attention. Despite the fact that sodium and lithium share similar electrochemical properties, which may cause the transition from lithium to sodium easier, the larger ionic radius of Na^{+ …}

Electrocatalytic Cathodes For Advanced Lithium–Sulfur Batteries, Ahmed Abdelkader

Theses and Dissertations

Energy demands are anticipated to increase in the next decades with the consumption of fossil fuels predicted to grow from the current levels. This will place an enormous burden on the non–renewable reserves of our energy sources and add to the preexisting environmental crisis with the emission of greenhouse gases like carbon dioxide (CO₂). Electrical energy storage (EES) is considered one of the most crucial needs of modern society to circumvent this crisis and potential applications include electric vehicles and devices, as well as storage systems for solar and wind sources.Lithium–ion batteries (LIBs) have proven to be …

Synthesis Of Supported Metal Nanoparticles On High Surface Area Supports For Application In Energy Conversion And Heterogeneous Catalysis, Nazgol Norouzi

Theses and Dissertations

Precise control of metal nanoparticles’ size, composition, and dispersity over high surface area supports are highly desirable to address current challenges in energy storage and conversion as well as catalytic processes involving precious metals. Therefore, developing viable synthetic routes that enable new catalytic systems derived from inexpensive transition metals or limited use of precious metals is vital for clean energy applications such as fuel cells and rechargeable batteries or affordable drugs in the pharmaceuticals arena. In addition to metal components of heterogeneous catalysts, the catalyst support is an integral part of catalyst design as it can impart both physical stability …

Structure, Morphology And Composition-Property Elucidation Of Ni–Mo And Ni−Mo−P Nanocrystals For Water Splitting Reactions And Group Iv Alloy And Silicate Nanocrystals For Visible To Near Ir Optoelectronics, Ebtesam Hassan Abuelenein Eladgham

Theses and Dissertations

Abstract

Structure, Morphology and Composition-Property Elucidation of Ni–Mo and Ni−Mo−P Nanocrystals for Water Splitting Reactions and Group IV Alloy and Silicate Nanocrystals for Visible to Near IR Optoelectronics

by

Ebtesam Hassan Abuelenein Eladgham

A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy at Virginia Commonwealth University.

Advisor: Indika U Arachchige

Associate Professor, Department of Chemistry

Nanomaterials have gained a great attention because of their unique physical properties with size intermediate between molecular materials and extended solids. They have a large surface to volume ratio and display size tunable physical properties that was not …

Semiempirical Molecular Modeling Analyses For Graphene/Nickel Oxide Nanocomposite, Islam Gomaa, Medhat A. Ibrahim, Hanan Elhaes

Nanotechnology Research Centre

Graphene metal oxide composite show applications in many areas according to their excellent electronic properties. Accordingly, graphene was subjected to interaction with NiO as adsorbing and a complex state. Semiempirical quantum mechanical calculations at PM6 was used to study the total energy, the final heat of formation, ionization energy, total dipole moment as well the charge distribution of the surface of graphene metal oxide composite. Calculated data indicated that graphene symmetry is changed into the C1 point group, forming stable composites with NiO that the complex composites were more stable compared with adsorb state composites. The change in the partial …

Derivatization Of Stable, Soluble Redox-Active Organic Materials For Non-Aqueous Redox Flow Batteries, Thilini Malsha Suduwella

Theses and Dissertations--Chemistry

In screening active materials for redox flow batteries (RFBs) – in which solubility is important to raise the volumetric energy density – scientists are slave to trial and error, modifying organic molecules in an attempt to optimize (increase) solubility without compromising other important properties such as stability and redox potential. A trained chemist can often predict the trends of solubility with the structural modifications in the neutral state of the materials, but when it’s come to the charged state of the materials, it doesn’t follow the same trend as the neutral species and relative values are hard to predict. The …