Manufacturing Commons^™

An Investigation Into The Challenges Of Contemporary Additive Manufacturing: Insights Into The Metallurgical Response Of Materials And Relevant Solution, Huan Ding

LSU Doctoral Dissertations

Additive Manufacturing (AM) has gained attention in recent years due to its unique capabilities in the fabrication of complex parts. As with any new research, there is still a lack of sufficient understanding in the field of additive manufacturing, and further investigation is needed to solve existing problems. Ultimately, the aim is to enable the widespread use of AM components across various industries.

Chapter One provides a brief introduction to the background and current bottlenecks of additive manufacturing technology. Chapter two focuses on the development of high-strength 7075 aluminum alloy (Al7075) for Fused Deposition Modeling and Sintering (FDMS) technology. Al7075 …

Influence Of Technological Parameters On Chip Formation And Chip Control In Precision Hard Turning Of Ti-6al-4v, Elshaimaa Abdelnasser, Samar El-Sanabary, Ahmed Nassef, Azza Barakat, Ahmed Elkaseer

Mechanical Engineering

This article presents the results of an experimental investigation into the effect of process parameters in the precision hard turning of Ti-6Al-4V on chip morphology at both macro and micro levels. It also reports on the control of chip generation to improve chip evacuation and breakability at the macro level by varying the process parameters, namely, feed rate, cutting speed and depth of cut during turning tests. A scanning electron microscope (SEM) was used to examine the chips produced for a better understanding of chip curling mechanisms at the micro level. Surface roughness of the machined specimens was measured to …

Additive Manufacturing And Characterization Of Auxetic Structures, Jayesh P. Moore, Stephanie R. Ruzicka

College of Engineering Summer Undergraduate Research Program

An auxetic structure is an arrangement of unit cells that under a uniaxial load experiences expansion in both the longitudinal and transverse directions, resulting in a negative Poisson’s ratio (NPR). Research in auxetics has led to new insights into how non-linear mechanical reactions can be applied to various engineering fields. This project utilized stereolithography (SLA) 3D printing to manufacture auxetic test specimens to analyze of geometry-driven NPRs. With the distinctive mechanical properties of auxetic structures and vast applications, the future of product development of these geometries seems promising.

Additive Manufacturing For Medical Education, Michael Noon

College of Engineering Summer Undergraduate Research Program

A growing body of evidence is suggesting that anatomical knowledge, the keystone of many medical specialties, is suffering among new graduates. While a host of reasons are provided, one common thread that many point to is the decline of cadaver dissections in the classroom. Many virtual audio-visual tools are used to address this gap, yet evidence has shown their ineffectiveness. Given this gap, the high degree of flexibility found in additive manufacturing (AM), and the many uses AM has already found in the medical field, we propose its use to fill this gap, allowing for students to learn with touch …

Numerical Study Of Solar Receiver Tube With Modified Surface Roughness For Enhanced And Selective Absorptivity In Concentrated Solar Power Tower, Shawn Hatcher, Mathew Z. Farias, Jianzhi Li, Peiwen Li, Ben Xu

Manufacturing & Industrial Engineering Faculty Publications

Concentrated solar power (CSP) is a reliable renewable energy source that is progressively lowering its cost of energy. However, the heat loss due to reflected and emitted radiation hinders the maximum achievable thermal efficiency for solar receiver tubes on the solar tower. Current solar selective coatings cannot withstand the high temperatures that come with state-of-the-art CSP towers often needing to be recoated soon after initial operation. We intend to use Inconel 718 with different additive manufacturing (AM) practices to construct surfaces that allow for more light-trapping to occur. By adjusting printing parameters, we can tailor a surface to allow for …

Wire Deflection Investigation During Wedm Of Aisi 304 Stainless Steel: An Experimental And Numerical Study, Sara A. El-Bahloul, Mohamed G. Elkhateeb

Mansoura Engineering Journal

Wire electrical discharge machining (WEDM) is a specific form of electrical discharge machining that employs a small diameter wire electrode to cut a narrow kerf in the workpiece. Since the wire deflection has a negative effect on the performed cutting, this research seeks to study the resultant wire deflection during WEDM of AISI 304 stainless steel. This study is performed with the help of three types of modeling; namely, mathematical modeling, experimental modeling, and thermo-mechanical finite element modeling. The mathematical modeling is performed to analyze the stresses and the wire lag, while the experimental modeling is achieved to observe the …

Laboratory Glovebox, Jackson T. Tenne, Noah Fitzgerald, Scott Stirling, Danny Ho

Mechanical Engineering

The Laboratory Glovebox project aimed to create an affordable, functional, ready to use, airtight workstation enabling Dr. Ramanan Sritharan to continue his research of the mechanical properties of nanomaterials. When airborne, nanomaterials are a health risk if inhaled, so the design requires a hermetic seal to protect the user. The design was meant to emulate features of the glovebox used by Dr. Sritharan during his PhD research, but was optimized to meet a budget of $3000, much cheaper than comparable alternatives. Key design features included acrylic panels, a transfer chamber, glove mounts, and a main access door, all sealed to …

Optimizing Mn-Al Permanent Magnet Performance Through Control Of The Phase Transformation, Ternary Element Addition, And Advanced Processing, Thomas R. Keller

Dartmouth College Ph.D Dissertations

The growing need for electrical power in machines and vehicles brings with it a growing need for critical materials. The current high-performance permanent magnets (PMs) based on rare-earth (RE) elements Nd and Sm cannot escape the problem of raw material cost, geographic scarcity in the earth’s crust, and lack of circular global supply chains. This poses a problem of industrial ecology: can PMs be made from inexpensive, more abundant materials while still meeting sufficient performance criteria? PMs based on the magnetic τ phase of Mn-Al offer a possible alternative to REPMs. However, years of innovation have not yet achieved real-world …

Effects Of Machining Parameters Of C45 Steel Applying Vegetable Lubricant With Minimum Quantity Cooling Lubrication (Mqcl), Mayur A. Makhesana, Prashant J. Bagga, Kaushik M. Patel, Jaime Taha-Tijerina

Informatics and Engineering Systems Faculty Publications

One of the most significant performance indicators for measuring the machinability of materials is tool wear and surface roughness. Choosing the best combination of cutting parameters can help reduce production costs, which is what the manufacturing industry is interested in. At the same time, industries are always looking for an alternative to conventional flood cooling since its use creates an environmental burden and health concerns for the operators. Therefore, vegetable oil-based minimum quantity cooling lubrication (MQCL) is considered a cutting environment. Sunflower oil is utilized as base fluid in MQCL and applied to the cutting zone through a nozzle. The …

Fatigue And Fracture Of Electron Beam Melting Ti-6al-4v, William A. Grell

Electronic Theses and Dissertations

For applications in the aerospace field, selection of materials for a given design requires an understanding of critical properties, like fatigue and fracture, in addition to static mechanical and physical properties. With the ongoing advancements in metallic additive manufacturing techniques and the interest in applying the process to aerospace applications, there is a clear need to fully characterize properties. Arguably, the most attractive alloy for applications in aerospace is the Ti-6Al-4V alloy. The current dissertation examines the mechanical properties of the alloy, made by the Electron Beam Melting (EBM) Powder Bed Fusion (PBF) method. As illustrated in this work, the …

Life Cycle Energy Assesment Of Advanced Fiber Reinforced Composite Design And Manufacturing Methodologies, Urjit Lad

All Theses

Automotive industry at large is focused on vehicle light-weighting since a 6%-8% increase in fuel efficiency can be achieved with a 10% reduction in vehicle weight [1]. With the growing demand for cost-effective and sustainable light weighting of automobile structures, interest has increased in the application of fiber reinforced plastic (FRP) composites for use in the Body-in-White (BiW), which can account for up to 40% of the total vehicle weight. Traditional FRP composite manufacturing processes like vacuum assisted resin transfer molding, autoclave consolidation or use of automated fiber placement have been successfully used for marine and aerospace applications. However, these …

Laser-Induced Forward Transfer (Lift) Based Bioprinting Of The Collagen I With Retina Photoreceptor Cells, Md Shakil Arman, Ben Xu, Andrew Tsin, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

This study focuses on the 3D bioprinting of retina photoreceptor cells using a laser-induced forward transfer (LIFT) based bioprinting system. Bioprinting has a great potential to mimic and regenerate the human organoid system, and the LIFT technique has emerged as an efficient method for high-resolution micropatterning and microfabrication of biomaterials and cells due to its capability of creating precise, controlled microdroplets. In this study, the parameters for an effective femtosecond laser-based LIFT process for 3D bioprinting of collagen biomaterial were studied. Different concentrations of collagen I solutions were tested and 0.75 mg/ml to 1 mg/ml collagen Ⅰ was identified as …

The Influence Of Diversity Dimensions On Student’S Collaboration Success: What It Means For Workforce Development In Manufacturing, Oyinkansola Adeite

All Theses

Manufacturing productivity is measured by labor productivity which is the hourly output of the manufacturing economy. The recent reduction in productivity numbers by the United States Bureau of Labor Statistics emphasizes the need for workforce development. With globalization and technological advancements, diversity has emerged as a critical aspect for the workplace. By encompassing dimensions such as education, race, and age, diversity creates a tapestry of unique perspectives and experiences. This study’s aim is to figure out the effect of a diversity dimension on team performance using intelligent systems, and in addition, if extra dimensions of diversity further impact team performance. …

Developing Control System For Manufacturing Processes, Md Shahriar Forhad

Theses and Dissertations

Process control has been a critical component in today's manufacturing industry. Industrialists nowadays want reliable control to assure precision manufacturing. Modern control systems must be more dynamic, so that any needed modifications may be made quickly to accomplish the desired product change. For innovative research and development, system customization is critical to ensure freedom for experimental works. In addition, full control of manufacturing systems is necessary to realize and implement Industry 4.0. Often, it is difficult to achieve such control due to limited access to proprietary equipment. To this end, this thesis focuses on developing a custom control platform for …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

A Hybrid Metaheuristic And Computer Vision Approach To Closed-Loop Calibration Of Fused Deposition Modeling 3d Printers, Graig S. Ganitano, Shay V. Wallace, Benji Maruyama, Gilbert L. Peterson

Faculty Publications

Fused deposition modeling (FDM) is one of the most popular additive manufacturing (AM) technologies for reasons including its low cost and versatility. However, like many AM technologies, the FDM process is sensitive to changes in the feedstock material. Utilizing a new feedstock requires a time-consuming trial-and-error process to identify optimal settings for a large number of process parameters. The experience required to efficiently calibrate a printer to a new feedstock acts as a barrier to entry. To enable greater accessibility to non-expert users, this paper presents the first system for autonomous calibration of low-cost FDM 3D printers that demonstrates optimizing …

Estudio Termoquímico Asistido Por Computadora De Los Polifenoles Presentes En La Fresa [Thermochemical Computer Assisted Study Of Polyphenols Presented In Strawberry], Federico Lopez, Jeimmy Rocio Bonilla Méndez, Luis Ricárdez Sandoval, Hiram Moya, Daniela Mainardi, Arturo González Quiroga, Jeffrey Leon-Pulido

Manufacturing & Industrial Engineering Faculty Publications

Las fresas son un alimento importante en Latinoamérica debido a sus componentes químicos, puesto que son una considerable fuente de calorías y polifenoles. Estos elementos son útiles por su capacidad antioxidante y otras propiedades beneficiosas para la salud. Sin embargo, la presión y la temperatura pueden llegar a afectar la integridad molecular de estos componentes, por lo tanto, en el proceso de producción de diferentes productos basados en fresas, se requiere estudiar las propiedades termoquímicas de los diferentes polifenoles presentes en esta fruta. Para ello, se extrajeron datos de las principales familias de polifenoles, antocianinas, flavanoles, flavonoles, ácidos hidroxibenzoicos y …

Optimization Of Alti Pld Coating By Increasing Ti Content, N2 And Annealing Which Used For Skd61 Pins In Aluminum Die Casting, Rusman Kosasih, Maria Margaretha Suliyanti Prof, Dedi Priadi, Wisnu Usni

Journal of Materials Exploration and Findings

The Alumunium Titanium Nitrogen (AlTiN) coating is known as one of the best coating materials for protective coating, while Pulsed Laser Deposition (PLD) is a laser coating process used for electric layer and superconductor applications, producing thin films up to 20 µm in thickness. The combination of these two matters has already been researched and is still in progress. One major challenge in the aluminium casting industry is to minimize the damage caused to tool steel pins made from SKD61, when aluminium material sticks to the pin, and halting production. Therefore, research on effective coatings for tool steels and testing …

The Effect Of Current Density And Hard Chrome Coating Duration On The Mechanical And Tribological Properties Of Aisi D2 Steel, Indah Uswatun Hasanah, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The effect of hard chromium coating on AISI D2's mechanical properties and wear resistance has been investigated using the electrolysis technique with varying current and coating duration. The variations of current used are 0.8 A, 1.2 A, and 1.6 A, while the coating duration used are 300, 600 and 900 seconds. Characterization of the films was conducted using SEM-EDS, and XRD. It can be observed from SEM characterization that the chrome grains resulted from the electroplating process are fine. The XRD identify chrome compund on the surface coating. The highest hardness value was 520.6 HV on a sample with a …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

Enhancement Of Interlaminar Shear Strength Of Carbon Fiber Reinforced Polymer Composites With Freeform 3d Printing Using Magnetic Compaction & Zt-Cfrp Technologies, Mohammad Rakibul Islam

Graduate Theses and Dissertations (2019 - present)

Carbon Fiber Reinforced Polymer (CFRP) laminates often exhibit matrix-sensitive weaknesses and flaws when produced via conventional additive manufacturing (AM) techniques due to the introduction of voids and defects during the AM process. This thesis employs a new approach called Magnetic Compaction Force Assisted-Additive Manufacturing (MCFA-AM) to fabricate Carbon Nanofibers (CNF)Z-threaded CFRP (i.e., ZR-CFRP) composite laminates. This novel method utilized a magnetic force to simultaneously levitate, deposit, and compact Continuous Carbon Fiber Reinforced Polymer (C-CFRP) composites in free space and rapidly solidifies the CFRP part without any mold; and effectively reduces the voids. Previous studies have demonstrated that the incorporation of …

Modeling, Control, And Hardware Development Of A Thrust-Vector Coaxial Uav, Andrew North

Doctoral Dissertations and Master's Theses

This thesis introduces a unique thrust vector coaxial unmanned aerial vehicle (UAV) configuration and presents a comprehensive investigation encompassing dynamics modeling, hardware design, and controller development. Using the Newton-Euler method, a dynamic model for the UAV is derived to gain in-depth insights into its fundamental flight characteristics. A simple thrust model is formulated and modified by comparing it with data obtained from vehicle testing. The feasibility of manufacturing such a vehicle is assessed through the development of a hardware prototype. Finally, a linear state feedback controller is designed and evaluated using the non-linear dynamics model. The results demonstrate successful validation …

Image Segmentation With Human-In-The-Loop In Automated De-Caking Process For Powder Bed Additive Manufacturing, Vincent Opare Addo Asare-Manu

Theses and Dissertations

Additive manufacturing (AM) becomes a critical technology that increases the speed and flexibility of production and reduces the lead time for high-mix, low-volume manufacturing. One of the major bottlenecks in further increasing its productivity lies around its post-processing procedures. This work focuses on tackling a critical and inevitable step in powder-bed additive manufacturing processes, i.e., powder cleaning or de-caking. Pressing concerns can be raised with human involvement when performing this task manually. Therefore, a robot-driven automatic powder cleaning system could be an alternative to reducing time consumption and increasing safety for AM operators. However, since the color and surface texture …

The Potential Of The Implementation Of Offline Robotic Programming Into Automation-Related Pedagogy, Max Rios Carballo, Xavier Brown

Publications and Research

In this study, the offline programming tool RoboDK is used to program industrial robots for the automation sector. The study explores the feasibility of using this non-disruptive robot programming software for classroom use; assesses how well RoboDK can be used to program various robots used in the industry; creates and tests various applications; and pinpoints technical obstacles that prevent a smooth link between offline programming and actual robots. Initial results indicate that RoboDK is an effective tool for deploying its offline programming code to a Universal Robot, UR3e. There are many potential for advanced applications. The goal of the project …

Empowering Student Success: Unlocking The Potential Of Project-Based Steel Design Education, Aly Mousaad Aly

Faculty Publications

In the pursuit of student success, it is essential to acknowledge that a singular teaching style does not universally cater to all students. The educator's crucial role lies in creating an optimal learning environment that fosters students' endeavors to excel. This endeavor transcends mere classroom success or employment prospects, encompassing a broader impact on societal well-being. An experiential learning approach, where students actively engage in practical tasks, emerges as the most effective mode of instruction. Integrating project-based learning activities into the curriculum holds immense potential for enhancing student learning. Additionally, the utilization of analysis software tools like FTool and STAAD …

Consumer 3d Printing For Remote Control Aircraft Wings: Development Of Novel Wingbox Structure, Ian Clark

University Honors Theses

Remote control aircraft construction and can be a very expensive and time-consuming hobby. With 3D printer consumer adoption rates skyrocketing, there is a gap between demand for RC aircraft and suitable well-designed models available to creators and hobbyists. By creating and testing two iterations of wingbox geometries, this research aims to help close that gap by producing an easily printable wing structure. While there are improvements that can be made on this work, this research has been effective in generating a novel wingbox structure for FFF 3D printing that has distinct advantages over other designs currently available.

Additive Manufacturing Of Stretchable Strain Sensors: Fabrication, Optimization And Application, John Nady Shihat Bastawrous

Theses and Dissertations

In this project, a novel strain sensor design is fabricated employing different additive manufacturing techniques. The spring sensor's primary material is PLA-Like resin with a nanocomposite encapsulation layer as the functional material. The main principle of Straining the sensors results in a change in resistivity as the distances among the conductive carbon particles change according to the strain applied.

Sensor fabrication consists of two parts: spring manufacturing and development of nanocomposite encapsulation The nanocomposite matrix is developed through the dispersion of Graphene and Carbon nanotubes in Thermoplastic Polyurethane through sonication and magnetic hotplate stirring. While the spring itself is manufactured …

Comparative Cutting Fluid Study On Optimum Grinding Parameters Of Ti-6al-4v Alloy Using Flood, Minimum Quantity Lubrication (Mql), And Nanofluid Mql (Nmql), Jaime Taha-Tijerina, Immanuel A. Edinbarough

Informatics and Engineering Systems Faculty Publications

Titanium alloys have been of paramount interest to the aerospace industry due to their attractive characteristics. However, these alloys are difficult to machine and require grinding post-processes for quality assurance of the products. Conventional grinding takes a long time and uses a flood coolant-lubrication technique, which is not cost effective nor environmentally friendly. Several studies have been performed to prove the viability and benefit of using Minimum Quantity Lubrication (MQL) with vegetable or synthetic-ester fluids. This work aims to find the optimum grinding parameters of creep feed grinding Ti-6Al-4V with a green silicon carbide wheel, using a flood lubrication system …

Fungi In Flux | Designing Regenerative Materials And Products With Mycelium, Arvind Bhallamudi

Masters Theses

As the world grapples with the escalating crisis of climate threats and environmental degradation, this research delves into the synergistic potential of design and biology, developing safe and sustainable materials for applications in prototyping, furniture and interior design. Harnessing the power of a unique organism - fungi, the study proposes an accessible, efficient, and resilient material resource system. It utilizes local waste streams and mycelium (the vegetative part of fungi) to grow functional structures. An experimental and small-scale protocol is modeled by testing bio-fabrication and bio-printing methods. The composites' performance qualities and characteristics are evaluated through mechanical testing and a …

Recor-Diy, Maxwell W. Ferrer

Industrial and Manufacturing Engineering

RecorDIY is an affordable alternative to ordering Vinyl Records from a manufacturer in the form of an at-home record-cutting lathe. This report will cover the record cutting process from audio to physical, at home record lathes that are currently available, and the possible improvements that I plan to implement in order to make these devices a more viable alternative for small artists. Current models can only create low fidelity records, specifically they struggle with lots of “noise”, extra sounds such as static that make it harder to hear the actual audio. Another issue is record size, as current models can …