Manufacturing Commons^™

Increase Of Heat Transfer To Reduce Build Time In Rapid Freeze Prototyping, Ming-Chuan Leu, Sriram Praneeth Isanaka, Von Richards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Reduction of part build time in the Rapid Freeze Prototyping (RFP) process, which fabricates a 3D ice part layer-by-layer by depositing and freezing water droplets, has been achieved by increase of heat transfer. Three mechanisms have been experimentally investigated: 1) cooling the substrate, 2) use of forced convection, and 3) use of a chilling plate. Cooling the substrate is effective for parts of small heights but becomes ineffective with increase in part height. Forced convection produced desirable reduction in part build time but with the undesirable formation of frost on the built ice part. The use of chilling plate to …

Functionally Graded Materials By Laser Metal Deposition, Syamala Rani Pulugurtha, Joseph William Newkirk, Frank W. Liou, Hsin-Nan Chou

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of functionally graded materials (FGMs) by laser metal deposition (LMD) has the potential to offer solutions to key engineering problems over the traditional metal-working techniques. But the issues that need to be addressed while building FGMs are intermixing in the layers and cracking due to the residual stresses. This paper is to present the study of the effect of process parameters (laser power and travel speed) on the degree of dilution between the substrate (or, previous layer) and powder material for few metallurgical systems.

Development Of A Melt Pool Tracking Vision System For Laser Deposition, Todd E. Sparks, Lie Tang, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper chronicles the development of a vision system for tracking melt pool morphology in the laser metal deposition process. This development is to augment an existing temperature feedback control system. Monitoring both the temperature and shape of the melt pool is necessary because of the effects of local geometry on the cooling rate at the melt pool. Temperature feedback alone cannot accommodate this effect without complex process planning. The vision system's hardware, software, and integration into the laser deposition system's controller is detailed in this paper. Preliminary testing and the effects on depositionquality is also discussed.

Evaluation Of Direct Diode Laser Deposited Stainless Steel 316l On 4340 Steel Substrate For Aircraft Landing Gear Application, Tian Fu, Todd E. Sparks, Frank W. Liou, Joseph William Newkirk, Zhiqiang Fan, Syamala Rani Pulugurtha, Jianzhong Ruan, Hsin-Nan Chou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

300M steel is used extensively for aircraft landing gears because of its high strength, ductility and toughness. However, like other high-strength steels, 300M steel is vulnerable to corrosion fatigue and stress corrosion cracking, which can lead to catastrophic consequences in the landing gear. Stainless steels offer a combination of corrosion, wear, and fatigue properties. But for an aircraft landing gear application a higher surface hardness is required. A laser cladding process with fast heating and cooling rates can improve the surface hardness. AISI 4340 steel is used as a lower cost alternative to 300M due to its similar composition. In …

Design And Development Of Rapid Battery Exchange Systems For Electric Vehicles To Be Used As Efficient Student Transportation, Jonathan A. Bevier

Master's Theses

Rapid battery exchange systems were built for an electric van and pedal assist electric bike as a method of eliminating the need to recharge the vehicles batteries in order to increase the feasibility of using electric propulsion as a method of efficient student transportation. After selecting proper materials it was found that the systems would need a protective coating to ensure consistent operation. 1020 cold rolled steel samples coated with multiple thicknesses of vinyl resin paint, epoxy resin paint, and powder coating were subjected to environmental wear tests in order to determine if the type and thickness of common protective …

Drop Impact Reliability Of Edge-Bonded Lead-Free Chip Scale Packages, Andrew Farris, Jianbiao Pan, Albert Liddicoat, Michael Krist, Nicholas Vickers, Brian J. Toleno, Dan Maslyk, Dongkai Shangguan, Jasbir Bath, Dennis Willie, David A. Geiger

Industrial and Manufacturing Engineering

This paper presents the drop test reliability results for edge-bonded 0.5 mm pitch lead-free chip scale packages (CSPs) on a standard JEDEC drop reliability test board. The test boards were subjected to drop tests at several impact pulses, including a peak acceleration of 900 Gs with a pulse duration of 0.7 ms, a peak acceleration of 1500 Gs with a pulse duration of 0.5 ms, and a peak acceleration of 2900 Gs with a pulse duration of 0.3 ms. A high-speed dynamic resistance measurement system was used to monitor the failure of the solder joints. Two edge-bond materials used in …

Design, Construction And Evaluation Of A Multi Layered Solar Distillation Prototype, Arlen A. Flanagan

BioResource and Agricultural Engineering

Water is arguably the most important resource to any individual; especially in areas of deserts and open oceans where drinkable water suppliers are scarce. The prototype Solar Desalination Unit allows normally undrinkable water to be distilled into a potable source with minimal inputs. The unit’s main power source is focused sunlight to thermally heat water inducing evaporation which is then condensed and collected. While solar desalination has been around for many years, lately more complex designs have been investigated in order to increase yields and efficiency. This paper focuses on the design, construction and testing of a Multi-Plate Solar Desalination …

Teaming Multi-Level Classes On Industry Projects, Lizabeth Schlemer, Jose Macedo

Industrial and Manufacturing Engineering

For the past few years we experimented with teaming students from a sophomore-level class and a senior-level class to work on industry projects. The classes are “work design” and “facilities design.” Projects are selected to require the application of knowledge from both disciplines. In addition, the projects are selected from small local companies. The intent of this paper is to describe the benefits and difficulties associated with this methodology. While specific classes in this experience are typical of an industrial engineering curriculum, the lessons learned and benefits could translate to other disciplines.

Optimization Of Engineering Tolerance Design Using Revised Loss Functions, Jeh-Nan Pan, Jianbiao Pan

Industrial and Manufacturing Engineering

Engineering tolerance design plays an important role in modern manufacturing. Both symmetric and asymmetric tolerances are common in many manufacturing processes. Recently, various revised loss functions have been proposed for overcoming the drawbacks of Taguchi's loss function. In this article, Kapur's economic tolerance design model is modified and the economic specification limits for both symmetric and asymmetric losses are established. Three different loss functions are compared in the optimal symmetric and asymmetric tolerance design: a revised Taguchi quadratic loss function, an inverted normal loss function and a revised inverted normal loss function. The relationships among the three loss functions and …

Finding And Optimising The Key Factors For The Multiple-Response Manufacturing Process, Jeh-Nan Pan, Jianbiao Pan, Chun-Yi Lee

Industrial and Manufacturing Engineering

With the advent of modern technology, manufacturing processes became so sophisticated that a single quality characteristic cannot reflect the true product quality. Thus, it is essential to perform the key factor analysis for the manufacturing process with multiple-input (factors) and multiple-output (responses). In this paper, an integrated approach of using the desirability function in conjunction with the Mahalanobis-Taguchi-Gram Schmit (MTGS) system is proposed in order to find and optimise the key factors for a multiple-response manufacturing process. The aim of using the MTGS method is to standardise and orthogonalise the multiple responses so that the Mahalanobis distance for each run …

Effects Of Reflow Profile And Thermal Conditioning On Intermetallic Compound Thickness For Snagcu Soldered Joints, Jianbiao Pan, Tzu-Chien Chou, Jasbir Bath, Dennis Willie, Brian J. Toleno

Industrial and Manufacturing Engineering

Purpose – The purpose of this paper is to investigate the effects of reflow time, reflow peak temperature, thermal shock and thermal aging on the intermetallic compound (IMC) thickness for Sn3.0Ag0.5Cu (SAC305) soldered joints.
Design/methodology/approach – A four-factor factorial design with three replications is selected in the experiment. The input variables are the peak temperature, the duration of time above solder liquidus temperature (TAL), solder alloy and thermal shock. The peak temperature has three levels, 12, 22 and 32°C above solder liquidus temperatures (or 230, 240 and 250°C for SAC305 and 195, 205, and 215°C for SnPb). The TAL has …

The Effect Of Ultrasonic Frequency On Gold Wire Bondability And Reliability, Jianbiao Pan, Minh-Nhat Le, Cuong Van Pham

Industrial and Manufacturing Engineering

This paper presents a systematic study on the effect of 120 KHz ultrasonic frequency on the bondability and reliability of fine pitch gold wire bonding to pads over an organic substrate with gold metallizations. The study was carried out on a thermosonic ball bonder that is allowed to easily switch between ultrasonic frequencies of 60 KHz and 120 KHz by changing the ultrasonic transducer and the ultrasonic generator. Bonding parameters were optimized through the design of experimental methodology for four different cases: 25.4 mm wire at 60 kHz, 25.4 mm wire at 120 kHz, 17.8 mm wire at 60 kHz, …

Development Of Extrusion On Demand For Ceramic Freeze-Form Extrusion Fabrication Processes, Parimal Sanjay Kulkarni

Masters Theses

"Freeze-form Extrusion Fabrication (FEF) is a Solid Freeform Fabrication method. It involves the deposition of a ceramic paste in a layer by layer manner to construct a three dimensional structure. The ceramic paste used in this process consists of a high solids loading of ceramic powder mixed with water and a nominal amount of an aqueous organic binder. These characteristics make the process environmentally friendly. Also the absence of dies or molds in the process makes it suitable for fabrication of materials like ceramics. In the past, parts have been fabricated with continuous extrusion of a ceramic paste. In FEF, …

Investigation Of Selective Laser Sintering Of Zirconium Diboride Parts, Shashwatashish Pattnaik

Masters Theses

"This research investigates the fabrication of three-dimensional parts from ZrB₂, an ultra high temperature ceramic (UHTC), using the selective laser sintering (SLS) process. Based on an experimental investigation, optimum values for the SLS parameters (scan speed, laser power, energy density, scan spacing and layer thickness), used on a DTM Sinterstation 2000, were determined to build green ZrB₂ parts with high integrity and sharp geometrical features. This was done by melting the polymer binder used to bond the ceramic particles layer-by-layer according to the cross-section of a CAD model. The use of a sacrificial plate to eliminate cracks in the bottom …

The Future Of The Irish Manufacturing Industry In Relation To Global Competitiveness, Joceley Martins Wilson

Theses

This study is an examination of the challenges faced by the manufacturing sector in Ireland. As the speed of globalization intensifies, new demands are constantly being levied on the manufacturing sector. In order to maintain this very important sector in Ireland, the manufacturing industry must promote constant innovation, automation and specialization, specifically in niche areas where there is a requirement for specific specialized skills, and where the labor cost is not a prohibitive or fundamental issue.

Innovation has been a key success factor for the manufactures to date, and will continue to be an ai'ea of focus as competitive forces …

Analysis Of Possible Use Of Identification Technologies In Disassembly, Vukica Jovanović, Sreten Filipović, Gordana Ostojić, Stevan Stankovski, Milovan Lazarević

Engineering Technology Faculty Publications

The barcodes and Radio Frequency Identification tags that are being used during manufacturing, assembly, warehousing, and distribution could also be reused at the end of the product lifecycle for an identification of the correct disassembly process that would result in recycling of its components. The barcodes or RFID tags can be helpful in identifying objects in terms of sustainable development, regarding disassembly, recycling and reuse. In this paper, the analysis of the current applications of RFID Technology in the final phase of the product lifecycle will be presented. The simulation of the disassembly process supported by both barcode and RFID-enabled …

Therapeutic Ultrasound Angioplasty: The Risk Of Arterial Perforation. An In Vitro Study, Mark Wylie, Garrett Mcguinness, Graham Gavin

Conference Papers

The use of therapeutic ultrasound delivered via small diameter wire waveguides may represent an emerging minimally invasive approach in the treatment of chronic total occlusions (CTOs), calcified and fibrous plaques. The distal-tip mechanical vibrations (typically 0-210 μm peak-to-peak) have been reported to debulk rigid calcified and fibrous tissues while healthy elastic arterial tissue remains largely unaffected. The risk of arterial (healthy tissue) perforation with energized waveguides is not fully understood. An ultrasonic apparatus capable of delivering a range of wire waveguide distal-tip displacements, up to 80 μm peak-to-peak (p-p), at an operational frequency of 22.5 KHz (+/- 6%) has been …

Ultrasonic Angioplasty: Assessing The Risk Of Arterial Perforation, Mark Wylie, Garrett Mcguinness, Graham Gavin

Conference Papers

Atherosclerosis is a cardiovascular disease that effects large and medium muscular arteries (such as coronary and iliac) and also large elastic arteries (such as aorta) [1]. It causes thickening of the arterial wall and over time can result in a completely blocked artery or chronic total occlusion (CTO). While the majority of atherosclerotic lesions can be attempted by typical Percutaneous Transluminal Coronary Angioplasty (PTCA) such as balloon and stent implantation, calcified CTOs are often problematic as they do not lend themselves to be accessed by the guidewire which is required to implant the balloon and stent. Excessive guidewire pushing force …

An Algorithm To Solve The Associative Parallel Machine Scheduling Problem, Mohannad Abdelrahman Shuaib

University of Kentucky Master's Theses

Effective production scheduling is essential for improved performance. Scheduling strategies for various shop configurations and performance criteria have been widely studied. Scheduling in parallel machines (PM) is one among the many scheduling problems that has received considerable attention in the literature. An even more complex scheduling problem arises when there are several PM families and jobs are capable of being processed in more than one such family. This research addresses such a situation, which is defined as an Associative Parallel Machine scheduling (APMS) problem. This research presents the SAPT-II algorithm that solves a highly constrained APMS problem with the objective …

Manufacture, Characterization, And Application Of Multiwall Carbon Nanotube Composite Crylonitrile-Butadiene-Styrene, Daniel Ray Bortz

University of Kentucky Master's Theses

Carbon nanotubes have been studied for nearly two decades and their amazing properties continue to spur intense investigation in the area of polymer composites. In terms of potential commercialization, mutiwall carbon nanotubes (MWCNTs) are currently the most prevalent and economically viable form of nanotubes. Uncovering innovative means to take full advantage of their properties remains a fundamental issue. In this thesis, viability of their use to reinforce polymeric systems is reported. Acrylonitrilebutadiene- styrene (ABS) was used as the host matrix. MWCNTs were introduced to the ABS matrix via melt compounding. The resulting composite was thoroughly rheologically, thermally, and mechanically characterized. …

The Effect Of Liquid Hot Filling Temperature On Blow-Molded Hdpe Bottle Properties, Benjamin S. Hudson

Theses and Dissertations

The occurrence of deformation in plastic bottles is a common problem in the bottling industry where bottles are blow molded, hot filled at high temperatures and sealed. Plastics have unique properties that make it difficult to predict when and why such changes may occur. The root cause of such deformation is unknown by many bottle producers and recent attempts have been made to minimize the occurrence of such defects. The purpose of this research is to determine which variables involved in the bottle production process influence bottle shape. Earlier variables that were tested included both blow molding resin and total …

Lean Six Sigma As A Source Of Competitive Advantage, Alessandro Giorgio Cavallini

Theses and Dissertations

Anecdotal data affirms that companies applying Lean Six Sigma in their operations not only deliver higher quality products and services, but also obtain superior financial results. The goal of this research was to empirically verify anecdotal data. The study proposed to analyze a group of publicly traded manufacturing companies with the intent of verifying if a correlation exists between companies being lean and the attainment of superior returns on investments. The researcher performed a series of statistical tests comparing key Financial Performance Indicators (FPI) extracted from annual reports (10-K) from a large pool of companies. The outcome of this study …

Drop Impact Dynamic Response Study Of Jedec Jesd22-B111 Test Board, Michael Krist, Jianbiao Pan, Andrew Farris, Nicolas Vickers

Industrial and Manufacturing Engineering

Mobile and handheld electronic devices are prone to being dropped. This drop event may result in failure of solder joints inside these devices. The need for RoHS compliant boards coupled with the demand for reliable electronics has resulted in the development of the JEDEC Standard JESD22-B111 to standardize the method of drop testing surface mount electronic components. However, there has been little study on the effects of additional mass on the board and rigidity of the board on drop test reliability. This paper examines the drop impact dynamic responses of the JEDEC JESD22-B111 board. Of interest are the effects of …

The Effect Of Ultrasonic Frequency On Gold Wire Bondability And Reliability, Jianbiao Pan, Minh-Nhat Le, Cuong Van Pham

Industrial and Manufacturing Engineering

This paper presents a systematic study on the effect of 120KHz ultrasonic frequency on the bondability and reliability of fine pitch gold wire bonding. The study was carried out on a thermosonic ball bonder that is allowed to easily switch between ultrasonic frequency of 60KHz and 120 KHz by changing the ultrasonic transducer and the ultrasonic generator. Bonding parameters were optimized through design of experiment methodology for four different cases: 25.4 μm wire at 60 kHz, 25.4 μm wire at 120 kHz, 17.8 μm wire at 60 kHz, and 17.8 μm wire at 120 kHz. The integrity of wire bonds …

Board Level Failure Analysis Of Chip Scale Package Drop Test Assemblies, Nicholas Vickers, Kyle Rauen, Andrew Farris, Jianbiao Pan

Industrial and Manufacturing Engineering

This paper presents the failure analysis results of board level drop tests. In this study, the test vehicle was designed according to the requirements of the Joint Electron Device Engineering Council (JEDEC) drop test board. The test vehicle was assembled with 15 chip scale packages (CSPs) each having 228 daisy-chained 0.5 mm pitch solder joints using Sn-3.0 wt% Ag-0.5 wt% Cu (SAC305) lead free solder. Assemblies were drop tested using three different peak accelerations of 900 G, 1500 G, 2900 G, with 0.7 ms, 0.5 ms, and 0.3 ms pulse durations, respectively. Scanning electron microscopy (SEM) with energy dispersive spectroscopy …

Work In Progress - Enhancing Student-Learning Through State-Of-The-Art Systems Level Design And Implementation, Albert A. Liddicoat, Jianbiao Pan, James G. Harris, Dominic J. Dal Bello, Lynne A. Slivovsky

Industrial and Manufacturing Engineering

The curriculum for undergraduate engineering programs is often partitioned into several courses that are taught in isolation followed by a single culminating senior design or capstone project experience. In the senior design class students being to synthesize the knowledge and skills that they acquired through the engineering curriculum. This paper presents lower and upper division course and curricular changes made to accommodate learning objectives that better prepare students for project-based learning. These learning experiences and skills include: systems level design, experience with state-of-the-art Computer Aided Design (CAD) tools, printed circuit board (PBC) design, design for manufacturability, electronics assembly, project management, …

Alternative Binder Carbide Tools For Machining Superalloys, Daniel J. Waldorf, Michael Stender, Scott Liu, Daniel Norgan

Industrial and Manufacturing Engineering

This study examines the performance of a new class of wear-resistant but economical cutting tools produced by varying the binder composition of standard cemented carbide composites. By replacing some or all of the cobalt binder with rhenium and nickel-based superalloy, a stronger composite tool results, potentially capable of machining heat-resistant superalloys at significantly higher cutting speeds. Sample tools with alternative binder were produced and compared to standard tools bound with cobalt only. Turning experiments on Inconel 718 were run to evaluate wear resistance and tool life for several grades. The experimentation also examined the effects of varying the relative proportions …

Development Of Comprehensive Agility Measurement Tool, Ameya Surendra Erande

Mechanical & Aerospace Engineering Theses & Dissertations

This research focuses on the development of Comprehensive Agility Measurement Tool. Industry independent use of such a tool would help enterprises benchmark their success in achieving agility.

Continuous improvement and modernization of manufacturing techniques around the globe have brought many mutations in manufacturing industry. Customer expectations and demands are behind the introduction of new paradigms such as mass production, lean, mass customization, agile and now internet-based manufacturing. Though lean was first coined with respect to manufacturing industry, soon it became applicable in all the industries based on its waste reduction and productivity improvement techniques. Lacking international competitiveness of US manufacturing …

The Development Research On Zhoushan Shipbuilding And Ship Repair Industry, Jing Zhou

World Maritime University Dissertations

No abstract provided.

Modeling And Experimental Results Of Concentration With Support Material In Rapid Freeze Prototyping, Frances D. Bryant, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Ice structures with complex geometries and overhung areas are created by the Rapid Freeze Prototyping (RFP) process in a sufficiently cool environment by freezing water into ice as the main material in conjunction with a eutectic dextrose-water solution as the sacrificial support material. The supported areas in an ice structure are removed via an increase in temperature in a separate environment after the structure is completely fabricated. To understand to what extent these two materials mix during fabrication, two methods of modeling the concentration changes that occur near the interface of the main and support materials have been developed. The …