Manufacturing Commons^™

A Strategy For Fabricating Complex Structures Via A Hybrid Manufacturing Process, Tarak A. Amine, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The purpose of this paper is to introduce a strategy for fabricating complex structures via a hybrid manufacturing process. The Laser Aided Manufacturing Process (LAMP) lab at Missouri S&T has developed a hybrid process combining both a direct metal deposition process and a five-axis CNC milling. Accessibility is a difficulty when finish machining internal features. The concept is to pause the deposition process to finish machine an internal feature while it is still visible is one possible solution to this issue. However, this must be done in a manner that will not be spoiled when the deposition process continues. This …

Numerical Simulation Of Ram Extrusion Process For Ceramic Materials, Mingyang Li, Lie Tang, Fei Xue, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The freeze–form extrusion process for aqueous-based ceramic paste is complex due to the non-Newtonian behavior of the paste. In this paper the process is studied numerically using a developed mathematical model. The ceramic paste viscosity is characterized by the Herschel-Bulkley model. The relationship between plunger velocity and extrusion force is computed numerically. The influence of air, which is mixed with the paste during the loading process, is also examined. Due to the compressibility introduced by the trapped air, the plunger force dynamic response is typically dominated by a first order response. It is also shown that the extrusion plunger force …

Process Planning And Control For Functionally Graded Material Fabrication Using Freeze-Form Extrusion Fabrication, Brad Deuser, Lie Tang, Jeff Geldmeier, Robert G. Landers, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using multiple materials in additive manufacturing technologies is critical for building parts with functionally gradient geometries. In order to achieve a desired material gradient, an advanced process planning and control system is required. This paper details the development of a process planning method and control system for functionally graded material fabrication using a triple extruder Freeze-form Extrusion Fabrication (FEF) system including motion code generation, extruder dynamic modeling and control, and composition gradient control. The effect that extruding multiple materials from a single orifice via static mixing has on the time delay of the resulting mixture is taken into account for …

Freeze-Form Extrusion Fabrication Of Composite Structures, Ming-Chuan Leu, Lie Tang, Bradley K. Deuser, Robert G. Landers, Greg Hilmas, Shi C. Zhang, Jeremy Lee Watts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A Freeze-form Extrusion Fabrication (FEF) process capable of making three-dimensional (3D) parts and structures with graded composite materials is presented in this paper. The process development includes the design and manufacture of a gantry machine with a triple-extruder mechanism and the associated electronics hardware and computer software for fabricating functionally graded parts from multiple aqueous pastes. A rheological behavior study with Al₂O₃ paste is performed to identify an efficient binder for transforming the paste into a pseudoplastic with a high yield stress. A green part is first fabricated using the triple-extruder FEF machine in a layer-by-layer manner …

Characterizing And Optimizing The Molten Salt Cleaning, Yangyang Long

Theses and Dissertations - UTB/UTPA

Molten salt cleaning is an important cleaning approach in remanufacturing which can remove a variety of contaminants from metal substrates with high efficiency. Facing the very limited research of this approach in literature, this thesis intends to characterize molten salt cleaning process and optimize its parameters when big parts with complicated shapes are cleaned. Based on the development of molten salt cleaning and studies on contaminations, two experiments are conducted. The first one investigates the influences of the hot salts on three metal substrates and shows the applicable of cleaning carbon steel and grey iron parts with molten salt. The …

Automating The Fret Slotting Process Using A Plc Controlled 1.5 Axis Mill, James Stratton

Purdue Polytechnic Masters Theses

Stratton, James A. M.S., Purdue University, August 2011. Automating the Fret Slotting Process Using a PLC Controlled 1.5 Axis CNC Mill. Major Professor: Richard Mark French.

Can automation assist small job shops and hobbyists in the production of stringed instruments? This research set out to answer the question using a quantitative approach to determine if an economical CNC machine could be produced in such a fashion as to seamlessly join the workshop as an affordable, yet precise instrument to aid in the production of stringed instruments. The key was to incorporate common industrial automation equipment into the operation of the …

Energy And Exergy Efficient Grate Clinker Cooling System., Muhammad Irfan Shahinuddin

Student Works (2010-2019)

The cement production ranks among the most energy intensive industrial processes, for which energy expenditure alone typically accounts for 30-40% of the production cost. It also contributes towards atmospheric pollution via the emission of major air pollutants such as nitrogen oxides, carbon monoxide and particulate matter, and greenhouse gas carbon dioxide. The goal of this study is to improve the efficiencies of a grate clinker cooling system through the optimization of its operational parameters, which consequently reduces the cost of thermal energy and the emissions of air pollutants and greenhouse gas. The study uses two approaches, i.e. the conventional energy …

The Transfer Of Laser-Machined Micro-Structured Patterns From Silicon To Polymethyl Methacrylate, Warren E. Withrow

Mechanical & Aerospace Engineering Theses & Dissertations

This research project's purpose was transferring a micro-scaled pattern from a silicon wafer to a polymethyl methacrylate (PMMA), or acrylic, substrate through light absorption generated heat. The secondary objective was to determine if the pattern on the silicon wafer could then be transferred to silica (i.e. a microscope glass slide) through light absorption generated heat. Once this pattern-transfer technique is developed for the micro scale, it could be instituted on the nano scale. The experiment was designed to find an alternate method to that currently being used to mass-produce compact discs (CDs). The most popular method employs a stamping process …

The Inside-Out Classroom: A Win-Win Strategy For Teaching With Technology, Daniel J. Waldorf, Lizabeth Schlemer

Industrial and Manufacturing Engineering

As costs of higher education soar and many universities face uncertain funding models, institutional pressures have increased to improve instructor efficiency. At the same time, U.S. industry leaders and leading educators have called for improvements in engineering education based on more interactive, hands-on student learning experiences. Although many efforts have been made to take advantage of technology to either improve student learning or to maintain student learning while increasing instructor efficiency, few approaches have been shown to improve both learning and efficiency. A teaching method is proposed to improve student learning and increase student satisfaction while also addressing the instructors’ …

Evolving A Summer Engineering Camp Through Assessment, Katherine Chen, Lizabeth Schlemer, Heather Scott Smith, Teana Fredeen

Industrial and Manufacturing Engineering

EPIC (Engineering Possibilities in College) is a one-week summer program for high school students (entering 9th-12th grades) to learn about engineering and experience hands-on labs in a university atmosphere. It's an opportunity for students to explore the different types of engineering available at many universities. The aim of EPIC is to expand the College of Engineering mission to K-12 students: "To educate students for careers of service, leadership and distinction in engineering or other fields by using a participatory, learn by doing, ‘hands-on’ approach".

Design Projects With Out-Of-Town Companies, Lizabeth Schlemer

Industrial and Manufacturing Engineering

The capstone design class in the industrial engineering department at California Polytechnic State University, San Luis Obispo (Cal Poly) includes projects with companies. The projects are large ambiguous facilities design problems that allow students to incorporate many aspects of the IE curriculum. For the past 15 years students have been participating in these projects with local companies. Over the past several years, companies from out of town (200 miles to the north in Mountain View or 200 miles to the south in Oxnard) have participated. These out of town companies have presented certain logistical issues, but they have proven to …

Pop-A-Wheelie Design Team, Mackenzie Hill, Thuyen Nguyen, Shaun Van't Hul

Mechanical Engineering

The purpose of this report is to illustrate the Pop-a-Wheelie design team’s progression and implementation of a concept in regards to the project sponsored by Break the Barriers (BTB). The Pop-a-Wheelie design team was tasked to design two devices that will be attached onto wheelchairs. The devices should facilitate the independence of user’s ability to pop-a-wheelie and return to an upright position without any assistance. After a list of specifications was agreed upon, the design process initiated. All customer specifications are listed in Objectives section located in Chapter 1: Introduction. A complete engineering specification table can be found in the …

Cal Poly Human Powered Helicopter, Josiah Auer, Eric Behne, Dave Berry, Rebecca Hennings, James Koch, Ian Marquardt, Josiah Mayfield, Sean Miller

Mechanical Engineering

The following report encompasses the Cal Poly Human Powered Helicopter team’s efforts during the 2010-2011 academic year. The intention of this project is to further the knowledge of human powered helicopter design and to validate an ideal configuration through experimental tests and analysis. 

A. Background

The Sikorsky Prize offered by the American Helicopter Society has been the catalyst for many attempts at Human Powered Helicopter (HPH) flight. The requirement to win the prize is a continuous, human powered flight of more than 60 seconds that stays within a 10 meter square box and reaches an altitude greater than 3 meters …

Power Steering Concept, Anthony N. Escobedo, William Ryan Flores, Russell Haverstock

Mechanical Engineering

This senior project was created in conjunction with Edwards Lifesciences. This project was created under an non-disclosure agreement and will not be submitted to any outside sources. The submitted title page will act as proof of completion.

Peripheral Soldering Of Flip Chip Joints On Passive Rfid Tags, Md Syful Islam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Flip chip is the main component of a RFID tag. It is used in billions each year in electronic packaging industries because of its small size, high performance and reliability as well as low cost. They are used in microprocessors, cell phones, watches and automobiles. RFID tags are applied to or incorporated into a product, animal, or person for identification and tracking using radio waves. Some tags can be read from several meters away or even beyond the line of sight of the reader. Passive RFID tags are the most common type in use that employ external power source to …

Mechatronics Application To Solar Tracking, Danny L. Rodriguez Jr

Purdue Polytechnic Directed Projects

The purpose of this was to design and implement a two-axis solar tracking system utilizing the National Instruments C-Rio real time controller. In order to accomplish this a prototype was modeled in CAD. This prototype used two 12 V DC motors to change a solar panel's rotation and tilt based on feedback data from three cadmium sulfide photoresistors. This configuration was chosen for its ability to create both a left-right rotational and an up/down tilt differential. In Addition this approach uses National Instruments Labview to control a solar tracking system. Using Labview add uniqueness to this project by adding a …

Effect Of Gold Content On The Reliability Of Snagcu Solder Joints, Jianbiao Pan, Julie Silk, Mike Powers, Patrick Hyland

Industrial and Manufacturing Engineering

Electroplated Ni/Au over Cu is a popular metallization for PCB finish as well as for component leads, especially wire-bondable high frequency packages, where the gold thickness requirement for wirebonding is high. The general understanding is that less than 3 wt% of Au is acceptable in SnPb solder joints. However, little is known about the effect of Au content on the reliability of SnAgCu solder joints. The purpose of this study is to determine the acceptable level of Au in SAC305 solder joints. Three different package platforms with different Au thicknesses were assembled on boards with two different Au thicknesses using …

A Study Of The Cause Of Failure Of Rotationally Molded, High-Density Polyethylene, Sodium Hypochlorite Storage Tanks, Dixon Harold Abell

Theses and Dissertations

The topic of chemical oxidative degradation in rotational molded polyethylene (high-density cross-linked) chemical (sodium hypochlorite) storage tanks is an industry problem that ranks at the top of current business issues for manufacturers of chemical storage tanks. The degradation of these tanks not only compromises the physical and mechanical properties of the tank material, but reduces the life expectancy of the tank, eventually resulting in catastrophic tank failure. Premature tank failure comes at a hefty cost. The reputation of the manufacturer is questioned often resulting in immediate loss of customer satisfaction and future business. The leaking of the chemical from the …

High-Resolution, Non-Contact Angular Measurement System For Psa/Rsa, Ronald D. Sloat

Master's Theses

A non-contact angular measurement system for Pitch Static Attitude (PSA) and Roll Static Attitude (RSA) of hard disk drive sliders is designed and built. Real-time sampling at over 15 KHz is achieved with accuracy of +/- 0.05 degrees over a range of approximately 2-3 degrees. Measuring the PSA and RSA is critical for hard drive manufacturers to control and improve the quality and reliability of hard drives. Although the hard drive industry is able to measure the PSA and RSA at the subassembly level at this time, there is no system available that is able to measure PSA/RSA at the …

Intelligibility Of Electrolarynx Speech Using A Novel Hands-Free Actuator, Brian Madden, Mark Nolan, Ted Burke, James Condron, Eugene Coyle

Conference Papers

During voiced speech, the larynx provides quasi-periodic acoustic excitation of the vocal tract. In most electrolarynxes, mechanical vibrations are produced by a linear electromechanical actuator, the armature of which percusses against a metal or plastic plate at a frequency within the range of glottal excitation. In this paper, the intelligibility of speech produced using a novel hands-free actuator is compared to speech produced using a conventional electrolarynx. Two able-bodied speakers (one male, one female) performed a closed response test containing 28 monosyllabic words, once using a conventional electrolarynx and a second time using the novel design. The resulting audio recordings …

A Study Of Yield Quantity Discrepancy Reduction In Semi-Conductor Back-End Process., Allina Abdullah

Student Works (2010-2019)

The ultimate objective of manufacturing industries today is to increase productivity through system simplification, organizational potential and incremental improvements by using modern techniques like Kaizen. Competition and continuously increasing standards of customer satisfaction has proven to be the endless driver of organizations performance improvement. Kaizen refers to continuous improvement in performance, cost and quality. Kaizen strives to empower the workers, increase worker satisfaction, facilitates a sense of accomplishment, thereby creating a pride of work. It not only ensures that manufacturing processes become leaner and fitter, but eliminate waste where value is added. Kaizen by now is a widely discussed and …

Self Assembly In Additive Manufacturing: Opportunities And Obstacles, Nathan B. Crane, J. Tuckerman, G. N. Nielson

Faculty Publications

Purpose

Additive manufacturing offers substantial flexibility in shape, but much less flexibility in materials and functionality—particularly at small size scales. A system for automatically incorporating microscale components would enable the fabrication of objects with more functionality. This paper considers the potential of self assembly to serve as an automated programmable integration method. In particular, it addresses the ability of random self assembly processes to successfully assemble objects with high performance despite the possibility of assembly errors.

Methodology

A self-assembled thermoelectric system is taken as a sample system. The performance expectations for these systems are then predicted using modified one-dimensional models …

Perspectives On Quality Coordination And Assurance In Global Supply Chains, Ling Li, John N. Warfield

Information Technology & Decision Sciences Faculty Publications

The 2007 recall of Berko Electric Toe-Space Heaters made in the US, the recall of backpack blowers made in Japan, the recalls of toys and pet food produced in China have exposed the potential of global supply chain disruptions. This product recall storm leads to the issue of quality assurance in global supply chain management. Product recalls indicate that manufacturing companies are particularly vulnerable to ensure quality when they source via a global supply chain with poor visibility. Obviously, a supply chain cannot afford this kind of sourcing and supply structure that threatens the supply-chain integrity. This special issue on …

Innovative Air Breathing Design And Output Control For Portable Proton Exchange Membrane Fuel Cell, Amar Bala Sridhar

Masters Theses

"Proton Exchange Membrane (PEM) Fuel Cell Technology is an energy source that can provide several times more energy per unit volume than current lithium ion batteries that are available in the market today. The barriers that exist that prevent the fuel cell from entering the world of portable applications are mainly system architecture integration. The idea is to have a fully functioning fuel cell with optimum power output using an innovative chimney design. Tests were conducted to quantify the advantage of using a chimney with the fuel cell. Further research was done to shed light on how different chimney designs …

A Methodology Towards Comprehensive Evaluation Of Shape Memory Alloy Actuators For Prosthetic Finger Design, Kevin O'Toole

Doctoral

Presently, DC motors are the actuator of choice within intelligent upper limb prostheses. However, the weight and dimensions associated with suitable DC motors are not always compatible with the geometric restrictions of a prosthetic hand; reducing available degrees of freedom and ultimately rendering the prosthesis uncomfortable for the end-user. As a result, the search is on-going to find a more appropriate actuation solution that is lightweight, noiseless, strong and cheap. Shape memory alloy (SMA) actuators offer the potential to meet these requirements. To date, no viable upper limb prosthesis using SMA actuators has been developed. The primary reasons lie in …

Estimating Industrial Building Energy Savings Using Inverse Simulation, Franc Server, J. Kelly Kissock, Dan Brown, Steve Mulqueen

Mechanical and Aerospace Engineering Faculty Publications

Estimating energy savings from retrofitting existing building systems is traditionally a time intensive process, accomplished by developing a detailed building simulation model, running the model with actual weather data, calibrating the model to actual energy use data, modifying the model to include the proposed changes, then running the base and proposed models with typical weather data to estimate typical energy savings. This paper describes a less time-intensive method of estimating energy savings in industrial buildings using actual monthly energy consumption and weather data. The method begins by developing a multivariate three-parameter changepoint regression model of facility energy use. Next, the …

Development Of Virtual Engineering Simulation For Lean Education, Akalpit Kiran Gadre

Masters Theses

"Global competition and customer demands are pressing modern industry operations to become leaner. The race among the global corporations to "go lean" demands engineers with an in-depth understanding of lean philosophies. An overview of current methods for teaching lean shows that they include small scale hands-on projects, presentations, and guest lectures. There is a need to incorporate a more immersive virtual simulation to further inspire students. Many lean simulation games are available in the market; however, they lack simplicity, ability to store the results, and modeling power.

The goal of this research is to develop a virtual simulation platform, enabling …

Use Of Collaborative Learning Technology To Support Cross-Faculty Group Learning, Colm O'Kane, Jennifer Mcdonnell

Conference Papers

The scope of applications of computer supported collaborative learning (CSCL) has grown exponentially in recent years. This group of techniques has been found to be extremely effective as a collaborative tool to inspire scaffolding between students. It is also useful when several academic supervisors wish to view the same project work.

This paper describes the process and the motivation behind the first implementation of a campus pack-based project in Year 3 of Technological University Dublin's (DIT) BSc. in Product Design programme. Issues have been encountered in previous years with this cross-faculty managed project, but this work shows the potential that …

A Shock Tube Technique For Blast Wave Simulation And Studies Of Flow Structure Interactions In Shock Tube Blast Experiments, Nicholas N. Kleinschmit

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Improvised explosive devices (IED’s) are widely used against US and allied forces fighting in Iraq and Afghanistan. Exposure to IED blast may cause blast-induced traumatic brain injury (bTBI). The injury mechanisms are however not well understood. A critical need in bTBI-related research is the ability to replicate the loading conditions of IED blast waves in a laboratory environment. In this work, experimental studies have been carried out to explore the use of the shock tube technique for generating air shock waves that mimic the temporal and spatial characteristics of free-field blast waves and to investigate the blast wave-test sample interactions …

Development Of Lower Cost Imaging Systems For Laser Metal Deposition Process, Shyam Barua

Masters Theses

"Laser Metal Deposition (LMD) has been used as an additive manufacturing process in industries such as aerospace and die castings. LMD is especially useful in repair applications involving die repair. However, it is still not used widely in industry due to variations in the quality of parts. There are multiple interactions between various factors which influence the quality of deposit.

There exists a need for defect detection systems to detect any changes in the deposition quality during deposition. On demand detection enables adjustment in process parameters and minimization of rework cost.

Vision systems have been used extensively in the industry …