Manufacturing Commons^™

Fused Filament Fabrication Additive Manufacturing Of 17-4 Ph Stainless Steel: Process–Structure–Property Relationships In Magnetic Materials, Maanav Patel

Theses and Dissertations

Additive manufacturing (AM) enables the fabrication of complex metallic components through layer-by-layer processing directly from digital models. Among AM techniques, material extrusion–based processes such as fused filament fabrication (FFF) provide an accessible method for producing metal parts using filament feedstocks composed of metal powders and polymer binders. When applied to precipitation-hardening stainless steels such as 17-4 PH, the processing route and heat treatments can influence the resulting microstructure and functional properties. This work investigates the magnetic behavior of 17-4 PH stainless steel fabricated using FFF and evaluates how heat treatment conditions influence measured magnetic properties. Samples were produced and analyzed …

Pin-Plane Electrical Discharge Driven By A Mosfet Dc Current Source, Myles Perry, Sidmar Holoman, Daniel Wozniak, Shirshak Kumar Dhali

Electrical & Computer Engineering Faculty Publications

The generation of atmospheric pressure nonequilibrium plasma using electrical discharges is an active area of research due to its significance in a wide spectrum of applications including medicine, combustion, and manufacturing. In our attempt to create a helium plasma jet in a pin-plane discharge with a constant current source, we observed self-pulsating behavior. We present the results of the electrical, optical, and spectroscopic measurements carried out to characterize the discharge. The duration of the discharge is a few tens of nanoseconds, and the repetition rate is in the few tens of kHz. The effect of the gap distance and gas …

Process Optimization And Quality Control In Manufacturing Of Frp Composites By Vartm, Mohamed Emadeldin Omar Abdelhadi

Graduate Theses, Dissertations, and Problem Reports (ETD)

Railroad tank cars, being one of the most used means of transportation of hazardous material across the country, have not been structurally upgraded for a long time. Thus, the Pipeline and Hazardous Materials Safety Administration (PHMSA), a United States Department of Transportation (USDOT) agency, released a rule for safer transportation of highly hazardous and flammable liquids by railroad to enhance the design specifications of both the new and existing tank cars in May 2015. A multifunctional composite jacket is proposed as a new material to structurally enhance the railroad tank cars to withstand any accidents that could happen en route. …

Processing, Characterization And Performance Of Ceramic Liners For Hydrogen Gas Turbine Engines, Fahim Faysal

Graduate Studies Theses and Dissertations 2026

Advanced ceramics and ceramic matrix composites (CMCs) are known for their endurance at high temperatures. This study investigated the fabrication and testing of two material systems: silicon carbide nitride (SiCN) reinforced with yttria-stabilized zirconia (YSZ) fiber manufactured through polymer infiltration and pyrolysis (PIP), and 3D-printed alumina (Al₂O₃) ceramics. The CMC thermal stability at high temperatures was explored through a hydrogen torch test. The CMC surface could withstand a temperature of 1,400°C for 10 minutes during the torch test. Furthermore, the internal surface of a hydrogen combustion chamber was coated with CMC to assess its applicability as a protective barrier against …

Multi-Criteria Decision Making Methods In The Organisations' Maturity Assessment: Prisma And Delphi Techniques Perspectives, Jailos Mrisho Mzumile, Victoria Mahabi, Ismail W. R. Taifa

Tanzania Journal of Engineering and Technology (TJET)

Researchers often find it challenging to identify the appropriate Multi-Criteria Decision Making Methods (MCDM) to employ in various research areas that involve prioritising conflicting alternatives or criteria. A systematic literature review was conducted using the PRISMA technique to determine the most frequently and commonly employed MCDM methods in assessing organisational maturity across its functional areas. A total of 120 articles were identified for review, and a bibliometric analysis was conducted to map the relationships within the identified articles using VOSviewer 1.6.20 software. Moreover, frequent content analysis was performed to determine the most frequently employed MCDM methods in assessing an organisation’s …

Virtual Process Modeling Of Metal Additive Manufacturing Basedon Direct Energy Deposition In-Situ Failure, Jachin J. Ramirez

2025 Fall Honors Capstones Projects - Archive

This study builds a mesoscale finite element simulation to examine how internal stresses form during additive metal manufacturing using directed energy deposition. The goal is to track how heat and stress develop layer by layer and determine where a failure criterion could appear during the print. The model uses temperature-dependent material properties for Inconel 718 and a moving heat source defined with custom G-code.

Thermal results are mapped into a mechanical simulation to watch stress accumulate as new layers are added. Different scan paths were tested to determine whether varying heat exposure could reduce the extent of a region exceeding …

Design And Development Of Evacuated Photovoltaic-Thermal Systems For Efficient Cogeneration Of Heat And Electricity, Behnam Roshanzadeh

Mechanical Engineering ETDs

In conventional PV systems, most of the solar energy is dissipated into the environment as heat. Accordingly, hybrid Photovoltaic-thermal systems have been developed to utilize the waste heat from PV cells for various thermal applications. However, most PVT systems suffer from low thermal performance compared to solar thermal collectors, as the absorber plate in PVT systems is partially or fully covered by PV cells. This dissertation focuses on improving the thermal performance of PVT systems by introducing the evacuated PVT systems.

An evacuated-tube PVT system was designed and simulated for domestic hot water supply. The evacuated-tube PVT system demonstrated 40% …

Influence Of Build Plate Location On Tensile Properties And Residual Stresses In Lpbf-Fabricated Stainless Steel 316 Components, Yareli Zelaya Pavón

Honors Program Theses and Research Projects

Additive manufacturing (AM), particularly Laser Powder Bed Fusion (LPBF), enables rapid production of complex metal components with minimal waste. Stainless Steel 316 (SS316) is widely used in engineering applications due to its corrosion resistance and mechanical reliability. This study investigates the influence of build plate location on tensile properties and residual stresses in LPBF-fabricated SS316. Twelve tensile specimens and nine unsupported bridge structures were fabricated at different build plate positions using a “machine model.” Tensile testing provided stress-strain data to evaluate peak stress, elastic modulus, and strain at break, while bridge curvature measurements quantified residual stress through warping. Results indicate …

Detecting Non-Axisymmetric Instabilities In Fluid-Based Manufacturing Via Multi-View Tensor Analysis., Bidusi Khadka

Electronic Theses and Dissertations

Fluid-based manufacturing processes, such as inkjet printing and electrospinning, fabricate micro- and nano-scale structures with high precision, but are prone to complex fluid dynamics exhibiting axisymmetric and non-axisymmetric instabilities. Conventional monitoring often relies on single-camera inputs and symmetry assumptions, limiting the detection of three-dimensional anomalies like jet deflection. This study presents a novel multi-view streaming video-based anomaly detection framework to address this gap. The framework employs a modified Tensor Sequential Sampling (TSS) algorithm with edge-based sampling to capture geometric spatiotemporal features of each camera view using the videos obtained from an orthogonally positioned dual-camera setup. These features are fused with …

Multi-Criteria Decision-Making For Sustainable Design: Stakeholder Prioritization And Methodological Comparison In Solar And E-Bike Applications, Swagath Madhu Gowda

All Theses

This thesis focuses on using Multi-Criteria Decision-Making (MCDM) methods to support sustainable product design by addressing the trade-offs between environmental, economic, and social goals. The research is presented through two studies that demonstrate how both subjective and objective decision-making approaches can guide sustainability evaluations.

The first study applies the Analytic Hierarchy Process (AHP) to assess residential solar panels by incorporating stakeholder perspectives from sustainability experts, end users, and industry professionals. Using Life Cycle Sustainability Assessment (LCSA) data, this study identifies how different stakeholder groups prioritize sustainability criteria and applies Aggregation of Individual Priorities (AIP) to combine their judgments. A one-at-a-time …

Experimental And Numerical Study On The Influence Of Carbon Fiber Reinforcement On The In-Plane Compressive Properties Of 3d Printed Hexagonal Honeycomb Core Structures, Deon Wallace

All Theses

There is difficulty with numerically replicating the behavior of composite honeycomb core structures numerically due to the trouble of gathering material properties from a hollow structure. Also, complex part geometries and carbon fiber reinforcement strategies can lead to unwanted structural weaknesses and variance in material properties that may not be reflected in numerical analysis when the part is additively manufactured. In this study, edgewise compressive testing is used to characterize the mechanical behavior and performance characteristics of these structures. The experimental results indicate an increase in the Young’s moduli of the honeycomb core structures as carbon fiber concentration increases. However, …

Origami-Inspired Pneumatic Soft Robotic Gripper, Conor J. Schott

Master's Theses

This thesis presents the design and evaluation of a vacuum-actuated, origami-based soft robotic gripper. A custom Sea Urchin crease pattern forms a lightweight folding skeleton that collapses radially under vacuum. The system emphasizes low cost and accessibility through laser cutting, 3D printing, and silicone molding. The Sea Urchin geometry was selected after digital and physical screening of candidate crease patterns for smooth folding, low strain concentration, and uniform inward motion. The folding skeleton is laser cut from 4 mil drafting film and folded into a compliant core. Four membrane configurations were developed: an origami gripper with a 36-inch balloon (Design …

Full Factorial Design Of Carbon Content And Heating Temperature On Height Reduction In Bonnell Springs, Yurida Ekawati, Cendana Anggun Sasmitha, Mochamad Syamsul Ma’Arif

Journal of Mechanical Engineering Science and Technology (JMEST)

The durability of Bonnell springs, which are widely used in the manufacture of spring beds, is often compromised by height reduction during use, which negatively impacts product comfort and quality. This study aims to minimize spring height reduction by investigating the effects of heating temperature and carbon content in the spring steel. A full factorial experimental design was applied using two factors: heating temperature (250°C, 260°C, and 270°C) and carbon content (0.72%, 0.73%, and 0.74%). Nine treatment combinations were tested, with five replicates each, and the height reduction values were measured after 100 compression cycles. The data were analyzed using …

Experiential Learning And The Revitalization Of Manufacturing Education At The University Of Dayton, Sean Cahill

Research and Reflection on Learning and Teaching in Higher Education

This perspective paper explores the role of experiential learning in preparing future-ready manufacturing engineers at the University of Dayton, set against the backdrop of Dayton’s legacy as an industrial innovator and the broader national movement to revitalize domestic manufacturing. As automation, cyber-physical systems, and Industry 4.0 technologies reshape the manufacturing landscape, there is a growing need for engineers who possess both technical fluency and systems-thinking capabilities. To meet this need, the manufacturing engineering technology department implemented hands-on, integrated lab-and-lecture modules through support from the Experiential Learning Innovation Fund for Faculty (ELIFF). Grounded in Kolb’s Experiential Learning Theory and constructivist learning …

Intelligent Real-Time Flotation Froth Stability Monitoring Using Embedded Computer Vision: Lead (Pb) Processing Case Study, Ahmed Bendaouia, Taha Ismaili, Ismail Najib, Oussama Hasidi, Intissar Benzakour, Jianzhi Li, El Hassan Abdelwahed

Manufacturing & Industrial Engineering Faculty Publications

Froth stability in flotation refers to the ability of the froth layer to remain intact and avoid collapsing during the flotation process. A stable froth layer is crucial to maximizing mineral recovery and ensuring the efficient operation of flotation cells. Several factors influence the stability of the froth, including the depth of the froth, the crowding, the size of the bubbles, and the rate of movement of the froth. In this study, our main objective is to analyze and evaluate froth stability in real time, since it plays a critical role in process optimization for flotation-based mineral processing. We propose …

Bending Fatigue In Additively Manufactured Metals: A Review Of Current Research And Future Directions, Md Bahar Uddin, Sriram Praneeth Isanaka, Frank Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Metal additive manufacturing (MAM), also referred to as 3D printing, has proven remarkable in the fabrication of complex metal components in multiple sectors. However, the assessment of this revolutionary process through bending fatigue is frequently impeded due to concerns about mechanical and physical conditions of the printed components. The unique layer-by-layer production process results in varied microstructures, anisotropy, and intrinsic defects that considerably differ from traditionally manufactured wrought metals. This review article aims to integrate and evaluate historical and contemporary research on the bending fatigue of additively manufactured materials. More specifically, the impact of process parameters, build orientation, surface conditions, …

Process-Driven Manufacturability Constraints In Design For Wire Arc Additive Manufacturing, Monsuru Ramoni, Sampson Gholston, Albert E. Patterson

Manufacturing & Industrial Engineering Faculty Publications

Wire arc additive manufacturing (WAAM) has emerged as a useful option for large-scale metal additive manufacturing. It has gained widespread use in the aerospace industry and other applications that require large and complex custom parts. The process is a combination of a precise control system and a welding process, typically GTAW or MIG welding. It is a member of the directed energy deposition (DED) family of AM processes. Compared with many metal AM processes, it is relatively simple and cost-effective but almost always requires a significant amount of postprocessing before parts can be used. The AM-based nature of the process …

Characterizing Surface Waviness Of Aluminum Alloy: An Approach To Minimize Post-Processing In Wire Arc Additive Manufacturing (Waam) Production, Shammas Mahmood Shafi, Anis Fatima, Nicholas V. Hendrickson

Michigan Tech Publications

Wire Arc Additive Manufacturing (WAAM) offers high deposition rates and cost-effective production of large metal components but suffers from poor surface quality, particularly surface waviness, which increases post-processing requirements and limits industrial adoption. Since waviness directly impacts structural integrity, resource efficiency, and industrial applicability, understanding how process parameters govern this feature is critical for reducing post-processing requirement. This study systematically investigated the influence of voltage, travel speed, and wire feed speed on surface waviness in aluminum alloy walls fabricated by WAAM. A two-level factorial design with 16 experiments was conducted, and surface waviness was quantified using height gauge measurements relative …

Hydrogen Embrittlement In Shot-Peened Steel, Jia-Huei Tien, David R. Johnson, David Bahr

15th International Conference on Shot Peening

This work investigates the role of shot peening on hydrogen embrittlement resistance in quenched and tempered 1070 steel. Thermal desorption spectroscopy results revealed that shot-peened specimens contained nearly twice the hydrogen (H) content of unpeened samples when charged under the same electrochemical conditions, suggesting the introduction of additional trapping sites occur during peening. The mechanism underlying this behavior can be associated with increased dislocation density and is more consistent with the HELP mechanism. Residual stress measurements show a significant relaxation of compressive stresses in shot-peened specimen after H charging, indicating H enhanced dislocation rearrangement. Both unpeened and peened specimens exhibited …

Anisotropic Residual Stress Measurements In Additively Manufactured 316 Stainless Steel Parts, Rajeshree Varma, Donovan Stumpf, Paul R. Mort

15th International Conference on Shot Peening

Additive manufacturing (AM) using laser powder bed fusion (L-PBF) is increasingly used to produce complex parts for industries like aerospace and medical devices. The intrinsic characteristics of AM – layer-wise deposition and rapid thermal cycling – generate significant, anisotropic, residual stresses that can compromise part quality and performance. Recent studies highlight how these stresses are strongly influenced by process parameters and build orientation. X-ray diffraction (XRD) techniques, including sin²ψ and advanced two-dimensional approaches, have become the preferred methods for non-destructive, directionally resolved measurement of residual stress in AM metals. This review surveys advancements in XRD residual stress methods with a …

From Strain To Stress: Stress Map Testing Of Almen Strips, Donovan Stumpf, Rajeshree Varma, Paul R. Mort

15th International Conference on Shot Peening

Almen strips have long been used to evaluate shot peening intensity, with arc height serving as a proxy for compressive residual stress. Stress mapping tests (SMT) in this work involve the controlled flattening of an Almen test strip onto a spatial pressure sensor, acting as an inferential measurement for the net bending moment caused by the relaxation of the peened strip. This work explores how stress mapping tests add insight into the stress state of Almen strips, potentially offering a fast and practical alternative to residual stress depth profiling. SMT data analysis provides a framework for relating Almen gauge height …

Fourier Analyses Of Optical Profilometry As An Inferential Measurement For Impact Coverage., Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A critical consideration in peening process design is achieving sufficient impact coverage. Conventional methods for assessing coverage rely on manual inspection, which is time-consuming and poorly suited for automated control. In this work, we investigate the use of frequency-domain analysis to quantify surface modification in peened samples using optical profilometry (OP) data. Three-dimensional surface maps of Almen strips were acquired using a high-resolution OP system and analyzed via fast Fourier transform (FFT) to compute spatial power spectral densities (PSDs). PSD maps and radially averaged profiles reveal consistent amplification of harmonic components similar to the nominal particle size, with increasing intensity …

Comparison Of Peening Effect Between Additive Manufacutred And Drawing Titanium Alloy, Hitoshi Soyama

15th International Conference on Shot Peening

Although additively manufactured (AM) metals are attractive materials, their remarkable weak fatigue properties are an obstacle to their practical application. Thus, post-processing to improve their fatigue properties is required. In the present study, powder bed fusion using laser sintering titanium alloy, i.e., PBF-LS/Ti6Al4V was treated by shot peening (SP), submerged laser peening (SLP), cavitation peening (CP), and fine particle bombarding (FPB), then the fatigue properties were investigated by a torsional fatigue test, comparing with drawing Ti6Al4V. It was revealed that the fatigue strength at 10⁷ was 446 ± 5 MPa for PBF-LS/Ti6Al4V treated by FPB+CP, 359 ± 9 MPa …

Reduced Order Approach For Peening Stress Field Variability, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A common goal in shot peening research is to connect operational parameters to resultant residual stress fields, providing a means to control and optimize the effectiveness of surface treatment. In practice, experimental measurements of residual stresses are often averaged values over regions that are large in comparison to an impact dimple. In fact, the stochastic nature of impact locations leads to residual stress fields that are distributed. Finite element peening simulations confirm this observation. The goal of this report is to connect operational parameters to localized fluctuations in residual stress through probabilistic reasoning (Figure 1). In particular, the development of …

Investigations On The Fatigue Strength Of Threads Produced By Different Fabrication Techniques, Philippe Du Maire, Jürgen Hoffmeister, Andreas Öchsner, Michael Johlitz

15th International Conference on Shot Peening

The increasing importance of sustainability in engineering demands the development of long-lasting, high-performance components that reduce material and energy consumption over time. This study investigates how different thread manufacturing processes, i.e., cutting, rolling, and deep rolling, affect the fatigue strength of bolts made from 42CrMo4+QT steel. Cylindrical specimens with M12 threads were subjected to cyclic tensile loading with constant mean stress. Fatigue strength was evaluated using the staircase method, and supporting analyses included X-ray diffraction for residual stress, and full width half maximum examination and Vickers microhardness measurements. Results show that thread rolling significantly improves fatigue strength, achieving 113.8 MPa …

Effect Of Fine Particle Peening Induced Material Transfer On The Initial Deposition Behavior Of Nickel Electroplating On Aluminum Substrate, Kazuki Iijima, Yutaka Kameyama, Hideaki Sato, Shuhei Kodama

15th International Conference on Shot Peening

Plating on aluminum requires a complex zincate pretreatment. Fine Particle Peening (FPP), using particles ≤200 µm, has gained attention as an alternative due to its ability to transfer particle components onto the surface, potentially improving deposition and adhesion. Previous studies showed enhanced plating on aluminum treated with steel particles. This study investigates the effectiveness of FPP as a pretreatment for nickel electroplating by examining initial deposition behavior. A1050-H24 aluminum was treated using FPP with either steel or glass particles, compared to an untreated specimen. Steel particle FPP created a lamellar microstructure with alternating iron and aluminum phases. EBSD revealed that …

The Effect Of Surface Treatment On The Fatigue Strength Of Sus316l Additive Manufactured Products, Hitoshi Nishijima, Yuji Kobayashi, Toshiya Tsuji, Kiyotaka Masaki

15th International Conference on Shot Peening

Rotating bending fatigue tests were conducted to investigate the effect of shot peening and barrel finishing on fatigue properties of SUS316L made by laser PBF which was one of additive manufacturing processes. Surface roughness, residual stress, and fatigue strength were investigated for each specimen. As a result, the fatigue strength of the barrel finished specimens was almost same or better than that of the shot peened specimens. Barrel finished specimens increased 4.1 times higher fatigue strength than as-built specimens. The surface roughness of the specimens after barrel finishing was reduced by up to 96% compared to the as-built specimens. On …

Expansion Of Laser Peening Application With A High-Power Microchip Laser On A Robotic Arm, Yuji Sano, Yoshio Mizuta, Satoshi Tamaki, Tomonao Hosokai, Tomoharu Kato, Yoshihiro Sakino, Volker Schneidau, Sebastian Holz, Jörg Behler

15th International Conference on Shot Peening

Laser peening (LP) introduces compressive residual stress (RS) onto the surface of metallic materials using nanosecond laser pulses irradiated through a water layer, thereby effectively suppressing fatigue crack initiation. However, conventional LP systems require large, stationary setups, restricting their use to indoor environments. To overcome this limitation, a portable LP device featuring a finger-sized microchip laser mounted on a collaborative robot arm has been developed. Equipped with a compact power supply and a water circulation/recovery system, the device can operate on-site with minimal setup. Successful processing across various materials has confirmed both compressive RS induction and fatigue life extension. Notably, …

Effects Of Laser Peening On Fatigue Properties Of Welded Aluminum Thin Plates, Kiyotaka Masaki, Yoshio Mizuta, Satoshi Tamaki, Yuji Sano

15th International Conference on Shot Peening

To improve the fatigue properties of welded aluminum alloy thin plates used in transportation machinery, handheld laser peening (HH-LP) was applied to 2 mm-thick A5083-O specimens prepared by bead-on TIG welding. Conventional laser peening often causes warping in thin plates, but the HH-LP treatment using low-energy laser pulses avoids this problem. The HH-LP treatment introduced compressive residual stresses of over 200 MPa on the heat-affected zone (HAZ) of the welded specimens. Fatigue tests under plane bending conditions revealed that the HH-LP treatment significantly improved the fatigue strength of the welded specimens, achieving a level comparable to that of the base …

Evaluation Of Peening Intensity With Nozzle-Mounted Sensor During Processing, Akinori Matsui, Shuji Hayashida, Yuji Kobayashi

15th International Conference on Shot Peening

In recent years, digital technologies have been increasingly applied in manufacturing, including visualization and anomaly detection in production equipment. In shot peening, Peening Intensity is a key process control indicator, but its measurement requires significant manual effort. This study aims to evaluate the possibility of using an AE-sensor-mounted nozzle to estimate Peening Intensity. We conducted experiments comparing sensor outputs with experimented Intensity under controlled conditions. A strong correlation (R² ≥ 0.95) was observed, suggesting that Peening Intensity can be estimated via AE sensing. This approach may contribute to labor-saving and automation in shot peening processes.