Mechanics of Materials Commons^™

Failure Characteristics Of Scs-6/Ti-24al-11nb Composite With A Circular Hole At Room And Elevated Temperatures, Joseph E. Overbeck

Theses and Dissertations

Off-axis loading of eight ply, unidirectional specimens with and without a circular hole determined the ultimate tensile strength of SCS-6/Ti- 24A1-11Nb composite at temperatures of 25°C and 650°C and fiber orientations of 0 degrees, 15 degrees, 45 degrees. Longitudinal moduli of the tested orientations compared closely to the rule of mixtures calculated values, and strengths compared closely to those predicted by the Tsai-Wu failure theory. The small diameter hole does not act as a stress concentrator, but merely reduces the material's strength in proportion to area loss. This result differs from those predicted by linear finite element analysis and orthotropic …

Failure Characterization Of A Fiber Reinforced Ceramic Matrix Composite With Circular Holes, Daniel E. Bullock

Theses and Dissertations

The purpose of this study was to investigate the performance of a fiber reinforced ceramic matrix composite with circular holes. The specific objectives were to (1) determine the relationship between tensile failure stress and the ratio of hole diameter to specimen width, and (2) to examine the initiation and progression of damage. The ceramic matrix composite used was SiC/ 1723, composed of continuous silicon titanium carbide fibers in an aluminosilicate glass ceramic matrix. Uniaxial tensile tests were performed at room temperature on two different layups; unidirectional [0]₈, and [0/90]_2s symmetric. Each layup was tested at three diameter-to-width …

Room Temperature Wear Characteristics Of Al2O3-Particle-Reinforced Aluminum Alloy Composite, A. R. Nesarikar, Surendra N. Tewari, E. E. Graham

Chemical & Biomedical Engineering Faculty Publications

Room temperature dry wear and friction properties of a metal matrix composite sliding against cast iron have been studied in a pin-on-plate reciprocating wear tester. The composite consists of Al₂O₃ particles in an aluminum alloy matrix. Wear is caused by abrasion, interfacial adhesion and ploughing of the softer surface with the asperities of the harder surface and the debris. With increasing load the friction coefficient and wear initially increase and then ecrease. The decreases in wear and friction are caused by increased hardness resulting from re-embedding of the fractured Al₂O₃ particles near the surface …

An Experimental Investigation Of Composite Sensors For Crack Length Measurement, Manickam Ramasamy

Mechanical & Aerospace Engineering Theses & Dissertations

Structural defects such as cracks can cause catastrophic failure in engineering components or structures. There are many techniques to measure the crack growth in materials and are commercially available. In this thesis, bondable crack length measurement gages have been investigated and these gages give electrical signal as the output and measure the crack length continuously. Silver paint, nickel powder impregnated epoxy and carbon powder impregnated polymer composite gages are investigated and tests are conducted by resistance measurement method with simple instrumentation and by potential drop method with a constant current output source. Rectangular shape gages have been investigated and as …

An Experimental Study On Anisotropic Behavior Of Granular Materials, Jong Woon Choi

Civil & Environmental Engineering Theses & Dissertations

Two types of mixtures of glass bead assemblies (large beads and small beads) were used to investigate the source of the anisotropy of granular materials in volume change behaviors during shearing process. Most tests (7 series) were conducted in the conventional triaxial device while a series of the experiments were in the hollow cylinder test device. All the specimens were first isotropically consolidated up to 137.9 kPa and were subjected to shearing in triaxial compression and triaxial extension modes with a constant effective mean normal stress (137.9 kPa). The test results indicated that all the specimens had a strong but …

Automating Tolerance Synthesis: A Framework And Tools, Stephen C.-Y. Lu, Robert G. Wilhelm

Department of Mechanical and Materials Engineering: Faculty Publications

This paper describes CASCADE-T—a new approach to tolerance synthesis that uses a complete representation of the conditional tolerance relations that exist between features of a part under design. Conditional tolerances are automatically determined from functional requirements and shape information. Tolerance primitives based on the virtual boundary requirements approach to tolerance representation are composed to form more complex tolerance relationships. Artificial intelligence techniques, including a constraint network, frame-based system, and dependency tracking are used to support flexible and detailed computation for tolerance analysis and synthesis.

Investigation Of Fatigue Damage Mechanisms In A Metal Matrix Composite Under Elevated Temperature, Barry D. Portner

Theses and Dissertations

This study investigated the fatigue damage initiation and progression in SCS-6/Ti-15-3 under an environment of fatigue loading at isothermal temperature. This program included two parts. First, an 808 Ultimate Tensile Strength system was set up to accommodate testing at two frequencies of 2.0 and 0.0208 cps at a constant temperature of 427° C. Second, at intervals during the load cycle process, the test specimens were characterized by establishing damage parameters based on changing modulus of elasticity, average strain, strain range, and ultimate tensile strength. Damage progression was documented in the form of failure of the fiber-matrix interface, matrix cracking, fiber …

Failure Mechanisms In A Quasi-Isotropic Ceramic Composite Laminate Under Tensile Fatigue Loading, Gregory D. Tracy

Theses and Dissertations

A study was conducted to experimentally investigate the tensile fatigue damage mechanisms in a quasi-isotropic ceramic matrix composite (Corning's Nicalon/CASIII). The goals of this study were to (1) develop a grip fixture for a servo-hydraulic MTS test machine and (2) conduct a series of tests with (0/±45/90)s specimens subjected to tensile fatigue loading to study their fatigue damage growth mechanisms. Results showed that when the material was subjected to stresses below 90 MPa, it lasted over 1000000 cycles but when stressed at or above 90 MPa, it failed in less than 1000 cycles.

Investigation Of Damage Mechanisms In A Cross-Ply Metal Matrix Composite Under Thermo-Mechanical Loading, Joel J. Schubbe

Theses and Dissertations

Metal matrix composites (MMCs) are rapidly becoming strong candidates for high temperature and high stiffness structural applications such as the Advanced Tactical Fighter (ATF). This study systematically investigated the failure modes and associated damage in a cross-ply, [0/90]_2s SCS6/Ti-15-3 metal matrix composite under in-phase and out-of-phase thermomechanic fatigue. Initiation and progression of fatigue damage were recorded and correlated to changes in Young's Modulus of the composite material. Experimental results show an internal stabilization of reaction zone size but degradation and separation from constituent materials under extended cyclic thermal loading. Critical to damage were transverse cracks initiating in the 90° …

The Effectiveness Of Viscoelastic Damping Treatments On A Flexible Manipulator Subjected To Torsional Loads, Leah L. Remias

Mechanical & Aerospace Engineering Theses & Dissertations

The advent of new technology has led to an increasing number of missions in space. The space shuttle Remote Manipulator System (RMS) is a lightweight flexible manipulator currently used in NASA space missions. The future role of the RMS and similar flexible manipulators may include in-space construction and assembly tasks. Because these tasks require precise motion and short settling time of the end-point oscillations, effective vibration control schemes are being investigated.

Passive damping techniques have shown to provide a considerable amount of damping in controlling flexural vibrations. In this research passive damping via constrained viscoelastic damping treatments is explored as …

Nondestructive Detection Of An Undeserable Metallic Phase, T1, During Processing Of Alumnum-L Thumalloys, Otto Buck, David J. Bracci, David C. Jiles, Lisa J.H. Brasche, Jeffrey E. Shield, Leonard S. Chumbley

Department of Mechanical and Materials Engineering: Faculty Publications

A method is disclosed for detecting the T1 phase in aluminum-lithium alloys through simultaneous measurement of conductivity and hardness. In employing eddy current to measure conductivity, when the eddy current decreases with aging of the alloy, while the hardness of the material continues to increase, the presence of the T1 phase may be detected.

Determinations Of Molecular Weight And Molecular Weight Distribution Of High Polymers By The Rheological Properties, Joan Y. Z. Huang

Mechanical & Aerospace Engineering Theses & Dissertations

Several methods are reviewed by which the molecular weight (MW) and molecular weight distribution (MWD) of polymeric material were determined from the rheological properties. A poly (arylene ether) polymer with six different molecular weights was used in this investigation. Experimentally measured MW and MWD were conducted by GPC/LALLS (Gel Permeation Chromatography/Low Angle Laser Light Scattering), and the rheological properties of the melts were measured by a Rheometric System Four rheometer. It was found that qualitative information of the MW and MWD of these polymers could be derived from the viscoelastic properties, with the methods proposed by Zeichner and Pate1, and …

Stability Design Of A Slender Column With Curved Longitudinal Stiffeners, Mark S. Lake

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents the results of a stability design study of a slender column with curved longitudinal stiffeners for large space structure applications. The stiffened column concept is attractive because it allows the buckling load of a slender column to be increased at a fairly low cost in increased mass, and at no change in the column packaged size. Linear stability analyses are performed using a "linked-plate" representation of the stiffeners to determine stiffener local buckling stresses. Results from a set of parametric analyses are used to determine an approximate explicit expression for stiffener local buckling in terms of its …

Development Of Load Carrying Thermoplastic Components For An Automotive Emergency Braking System, Joseph Gerard Sikora

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis describes a classical approach to plastic parts' design leading to the development of load carrying fiber reinforced thermoplastic components for use in an automotive emergency braking system. The control arms that are the focus of this study are designed to withstand the static loads characteristic of the loads experienced by an automotive emergency braking system. The present study is particularly significant as a case study because the design involves development of load carrying components for use in the harsh automotive environment.

Beginning with a fundamental concept for the control arms, basic design criteria, and a limited insight into …

Optimal Cure Cycle Design Of A Resin-Fiber Composite Laminate, Jeenson Sheen

Mechanical & Aerospace Engineering Theses & Dissertations

High performance polymeric composites have been experiencing increasing usage in the aerospace and automobile industries. Such materials are commonly composed of long or chopped fibers embedded in the thermosetting resin matrix. Changes in physical and chemical properties of such composite materials during the cure process are rather complex. Thus, it is not a trivial task to properly design a cure cycle (temperature and pressure profiles) for a cure process. The material should be cured uniformly and completely with the lowest void content; the temperature inside the laminate must not exceed some maximum value; and the cure process should be completed …

Microcomputer Based Digital Image Processing System Developed To Count And Size Laser-Generated Small Particle Images, K. D. Ahlers, D. R. Alexander

Department of Mechanical and Materials Engineering: Faculty Publications

A microcomputer-based digital image processing system has been developed to count and size laser-generated small particle images. Processing rates of 5 to 600 frames per minute were achieved by utilizing a real-time digital image processor. Particles from 7 to 700 µm in the plane of focus were counted and sized. A major emphasis in this work was to determine the basic problems and limitations involved with using a digital image processing scheme to accurately size particles. Areas that were investigated include the effect of the threshold level on measured particle size, particle boundary diffraction gray-level gradients, and geometric nonlinearities introduced …

An Experimental And Analytical Investigation Of The Iosipescu Shear Test For Composite Materials, Barry Stuart Spigel

Mechanical & Aerospace Engineering Theses & Dissertations

Mechanical properties of composite materials under shear loading are difficult to determine. The Iosipescu Shear test, originally proposed for metals, has in recent years been applied to composites. It has the advantages of small specimen size, simple loading and a reasonably uniform shear stress in the test section.

The purpose of this work is to study the validity of the Iosipescu test method for measuring the shear modulus and shear strength of composites. Finite element analyses indicate that optimum specimen geometry and load locations depend upon the degree of orthotropy of the composite. Test results for a quasi-isotropic graphite/epoxy laminate …

Photoelastic Investigation Of Load Transfer In Eccentrically Loaded Single Lap Joints, Stephen Antrim Hann

Mechanical & Aerospace Engineering Theses & Dissertations

Photoelastic models of three eccentrically loaded single lap joints were analyzed. The adherends of each joint were identical and the bondlines differed in thickness and material properties. The adherends were analyzed for both cylindrical plate behavior and geometrical nonlinearity and the load transfer efficiency was examined. For all three models it was found that over 98% of the shank behaves as a cylindrical plate and that a geometrically nonlinear analysis yields bending stresses substantially lower than a linear analysis and that a relatively thick, low modulus bondline can increase load transfer efficiency.

Studies Of Fracture And Deformed Surfaces Of High Strength Aluminum Alloys By X-Ray Diffraction, Tamma K. Kumar

Mechanical & Aerospace Engineering Theses & Dissertations

X-ray observations of fatigue fracture and deformed surfaces of 7075-T6 aluminum were conducted in this study. The (111) and (222) diffraction peaks were obtained from the fractured and deformed surfaces. It was observed that in comparison with the base metal, the fracture exhibited line broadening similar to that due to cold working. The broadening is indicative of plastic deformation in the vicinity of the advancing crack tip during the fracture process. Also the different regions of fracture exhibited varying degrees of line broadening. With respect to the fatigue crack, the slow crack growth region showed a greater broadening, and, hence, …

Temperature And Time Dependent Viscosity Of An Elastomer Modified Epoxy Resin, Woodrow Williard Wagner Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Temperature effects on the viiscosity of an epoxy resin (diglycidyl ether of bisphenol A - DGEBA), an elastomer (carboxy terminated butadiene acrylonitrile - CTBN), and two blends containing nominally 10 percent elastomer were examined from strain rates of 0.1 sec^-1 to 10,000 sec-¹ over a temperature range from 300K to 450K. All results indicated the greatest drop in viscosity occurred for each of the materials over the temperature range of 300K to 350K. In addition, the materials exhibited Newtonian responses over the entire strain rate range, Adding small amounts of elastomer to the I epoxy only moderately effected …

Low Cost Fencing, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

Fences with more wire and posts are not necessarily stronger.

Design using high tensile wire can save on materials and reduce costs.

Some Aspects Of Reliability Theory And Life Testing, Danny Laforrest Dunham

All Master's Theses

This paper explores the properties of the mean life of an item when an exponential density is assumed for the item's life length. Two different tests are discussed, one where the items are allowed to fail while on test without replacement, and the second test where the items are replaced as they fail. Finally the efficiency of the two tests is explored with respect to the number of items that are allowed to fail versus the length of the test.

Studies Of Bistable Fluid Devices For Particle Flow Control, Gerald H. Hogland

Dissertations and Theses

This study was directed toward the development of a bistable wall attachment Flip-Flop device which was capable of directionally controlling particle flow. The particles were transported by a fluid stream which under the influence of wall attachment. The dominant criteria in the development of the device was the achievement of the highest recovery of particles at the active output, without destroying the wall attachment of the fluid stream The experiment was conducted in several distinct stages; each of which was concerned with at least one aspect of wa1l attachment or particle flow. Results derived from one test were used to …

Comparative Study Of Lightweight And Normal Weight Concrete In Flexure, Mohammad Zareh

Dissertations and Theses

This investigation represents a comparative study of the flexural behavior of lightweight and normal weight concrete. Both theoretical and experimental moment-curvature characteristics of the tested specimens were used to study the flexural behavior.

A generalized computer program to determine the moment-curvature relationships of a singly reinforced rectangular concrete beam was developed.

For this limited study it was observed that lightweight concrete beams when compared to normal concrete beams achieve comparable moment capacity (about 92% of normal weight concrete) but exhibit higher deflections (about 40% more than normal weight concrete).

Concrete In Dairies, D Roger Buchanan

Journal of the Department of Agriculture, Western Australia, Series 4

PRIME requirements for exposed concrete surfaces in dairies are that they should be easily cleansed and should not deteriorate in contact with milk and milk products.

In milking stalls, animal races and on loading platforms hardwearing surfaces which offer good foothold are also necessary.

Controlled Environment Broiler Houses In Western Australia, D F. Hessels

Journal of the Department of Agriculture, Western Australia, Series 4

The three main features which contribute to the better returns from controlled environment broiler housing are higher density, better conversion and a reduction in labour.

The higher initial cost of housing and higher running costs are more than covered by these three advantages.

Siphon Tubes For Furrow Irrigation In The Kimberleys, K S. Cole

Journal of the Department of Agriculture, Western Australia, Series 4

Irrigation soils in the Ord River area have a high clay content and erode easily under the influence of running water.

To overcome the problem of erosion in cuts between the head channels and irrigation furrows polythene siphon tubes have been found the most satisfactory.

In this article K. S. Cole, B.Sc. (Agric), Agricultural Adviser, Kununurra, describes the use of siphon tubes for furrow irrigation in the Kimberleys.

Plan For Quality In Silage, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

SILAGE making time is fast approaching in the South-West.

Last minute preparations before harvesting will help avoid delays at the time of making this valuable fodder, thereby reducing the amount of costly spoilage caused by hold-ups.

Its Shearing Time, Department Of Agriculture, Western Australia

Journal of the Department of Agriculture, Western Australia, Series 4

SHEARING will soon be taking place on your property. For a smooth annual wool harvest, remember:—

Blasting. Part 1. Explosives And The Farmer, G A. Greaves

Journal of the Department of Agriculture, Western Australia, Series 4

ABOUT 3,000 tons of commercial blasting explosives of various types are used every year in Western Australia of which approximately two thirds is utilised by mining industries and the remainder goes mainly to quarrying and public works.

The farmer and orchardist actually use only very small amounts but nevertheless explosives are a very useful working tool for the primary producer.