Engineering Science and Materials Commons^™

Precious Plastics - Plastic Brick Machine Fabrication, Timothy Ukaobasi Kanu, Evi Paraskevi Troulis

Architectural Engineering

The goal of this research is to determine the structural parameters of the recycled plastic polypropylene when molded into bricks resembling CMU blocks. To accomplish this, three mechanisms had to be assembled: the shredder, the injector, and the 1x1 mold. A tensile and compression test were to be performed on the plastic brick, and the values would be used to compare the tensile and compressive strength of PP plastic bricks, as well as their modulus of elasticity and stress vs. Strain performance. These values would be analyzed to determine whether it would be feasible to build an entire plastic wall. …

Advances And Challenges On Cathode Catalysts For Lithium-Oxygen Batteries, Bo Wen, Zhuo Zhu, Fu-Jun Li

Journal of Electrochemistry

Aprotic lithium-oxygen batteries (LOBs) with high theoretical energy density have received considerable attention over the past years. However, the oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) at cathodes suffer from slow kinetics for large overvoltages in LOBs. Significant advances on catalysts have been achieved to accelerate cathode kinetics, but understanding on the formation/decomposition processes of Li₂O₂ is limited. Herein, this review highlights the fundamental understanding of the correlation between catalysts and formation/decomposition of Li₂O₂. Various types of cathode catalysts are discussed to reveal the mechanism of formation/decomposition of Li₂O₂, …

Recent Advances In Anode Materials Of Solid Oxide Electrolysis Cells, Geng Zou, Wei-Cheng Feng, Yue-Feng Song, Guo-Xiong Wang

Journal of Electrochemistry

Solid oxide electrolysis cell (SOEC) as an electrochemical energy conversion device has attracted increasing attention due to its large current density, high Faradaic efficiency and energy efficiency. Oxygen evolution reaction at the anode, a four-electron transfer process, is an important half-reaction for SOEC, which contributes to the main polarization resistance and consumes most electric energy during the electrolysis process. Hence, designing anode materials with high activity and stability is crucial for the performance improvement and practical application of SOEC. Recently, some advances have been made in the development of high-performance anode. In the current review, the mechanisms for CO_{2 …}

Anodic Electrocatalysis Of Glycerol Oxidation For Hybrid Alkali/Acid Electrolytic Hydrogen Generation, Xin Feng, Bo-Wen Liu, Ke-Xin Guo, Lin-Feng Fan, Gen-Xiang Wang, Su-Qin Ci, Zhen-Hai Wen

Journal of Electrochemistry

Electrolytic hydrogen production is heavily restricted by high-energy consumption majorly due to the relatively high potential of anodic oxygen evolution reaction (OER). Development of OER-alternative reaction at the anode has been recently proposed as a promising pathway to address the associated issues. In this work, we report a hybrid acid/alkali dual-electrolyte electrolyzer by coupling acidic hydrogen evolution reaction (HER) using commercial Pt/C cathode with alkaline Electrocatalytic glycerol oxidation (GOR) which is implemented by developing a nickel foam (NF) supporting Co₃O₄ nanosheets anode that shows low overpotential and high selectivity toward GOR for formate production. The hybrid acid/alkali …

Multifunctional Microgel-Based Cream Hydrogels For Postoperative Abdominal Adhesion Prevention, Bo Liu, Yunfan Kong, Olawale A. Alimi, Mitchell Kuss, Huiyin Tu, Wenfeng Hu, Abu Rafay, Kumar Vikas, Wen Shi, Megan Lerner, William L. Berry, Yulong Li, Mark A. Carlson, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

Postoperative abdominal adhesions are a common problem after surgery and can produce serious complications. Current anti-adhesive strategies focus mostly on physical barriers and are unsatisfactory and inefficient. In this study, we designed and synthesized advanced injectable cream-like hydrogels with multiple functionalities, including rapid gelation, self-healing, anti-oxidation, anti-inflammation, and anti-cellular adhesion. The multifunctional hydrogels were facilely formed by the conjugation reaction of epigallocatechin gallate (EGCG) and hyaluronic acid (HA)-based microgels and polyvinyl alcohol (PVA) based on the dynamic boronic ester bond. The physicochemical properties of the hydrogels including anti-oxidative and anti-inflammatory activities were systematically characterized. A mouse cecum-abdominal wall adhesion model …

The Fourth Industrial Revolution: Opportunities And Challenges To The Future Of Mechanical Engineering, Ulingeta O.L. Mbamba

Tanzania Journal of Engineering and Technology (TJET)

This paper provides a conceptual overview of the developments of the Fourth Industrial Revolution (4IR) and derives challenges and opportunities for the future of the mechanical engineering profession. The paper broadly defines 4IR as the fusion of technologies and interaction across physical, digital and biological aspects, while defining mechanical engineering as "a multi-faceted discipline that encompasses the teaching, practice and guidance of others in the development and application of scientific principles to mechanical systems". The paper looks specifically at developments in the Internet of Things (IoT), blockchain technology, robotics, Big Data analytics, biotechnology, nanotechnology, 3D printing and artificial intelligence and …

Designing And Manufacturing Of Vegetable Slicing Machine, Juma Nuhu Msuya

Tanzania Journal of Engineering and Technology (TJET)

Agro-processing industry is faced with a challenge of slicing of vegetables for immediate consumption. This stems from the fact that the traditional slicing methods use bare hands, and knives. This method is faced with shortcomings of inefficiency, poor hygiene, and significant dangers to injury. If vegetables are not sliced, their drying takes longer, may possibly be spoiled, and cannot be stored for future uses. Therefore, this paper strives to design a vegetable slicing machine to increase the efficiency of the drying process as a post-processing step. The study employed a Pugh’s design model to design the machine and manufacture it. …

Preface To Special Issue On Electrocatalysis And Electrosynthesis, Fang-Yi Cheng, Shuang-Yin Wang, Tian-Hua Zhou

Journal of Electrochemistry

No abstract provided.

Highly Dispersed Pt Nanoparticles Root In Single-Atom Fe Sites In Ldhs Toward Efficient Methanol Oxidation, Qing-Cheng Meng, Lin-Bo Jin, Meng-Ze Ma, Xue-Qing Gao, Ai-Bing Chen, Dao-Jin Zhou, Xiao-Ming Sun

Journal of Electrochemistry

Active and durable electrocatalysts for methanol oxidation reaction are of critical importance to the commercial viability of direct methanol fuel cell, which has already attracted growing popularities. However, current methanol oxidation electrocatalysts fall far short of expectations and suffer from excessive use of noble metal, mediocre activity, and rapid decay. Here we report the Pt anchored on NiFe-LDHs surface hybrid for stable methanol oxidation in alkaline media. Based on the high intrinsic methanol oxidation activity of Pt nanoparticles, the substrates NiFe-LDHs further enhanced anti-poisoning ability and maintained unaffected stability after 200,000 s cycle test compared to commercial Pt/C catalyst. The …

Hemodynamic Investigations In Intracranial Aneurysms: A Commentary, Hang Yi, Mark Johnson, Luke Bramlage, Zifeng Yang, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

Intracranial aneurysms (IAs) are abnormal bulges in a blood vessel in the brain that have a potential to rupture and even causing a stroke, which can lead to lasting brain damage, long-term disability, or even loss of life. It has been widely acknowledged that hemodynamic factors, e.g., instantaneous wall shear stress, time-averaged wall shear stress, wall shear stress gradient, gradient oscillatory number, oscillatory shear index, pulsatile blood flow waveform (flow rate magnitude and shape, physical flow period), relative residence time/turnover time, blood pressure, and vortex (i.e., size, location, and numbers), have a close relationship with the pathobiology (i.e., initiation, growth, …

Influence Of Processed Natural Black Sand Vs. Natural White Sand And Silica Flour As Additives To Oil-Well Cementing Applications, Ramy Abuel Maaty

Theses and Dissertations

Cementing is a crucial and fundamental step in the process of drilling wells to extract oil from its reservoirs. Cementing main functions are to achieve zonal isolation and provide mechanical support to the casing. Impermeable and powerful cement is strongly desired to withstand high pressures and temperatures during the lifetime of the producing wells. Various additives to cement, such as silica flour, fly ash, Nano-additives and other advanced materials have been used and tested to attain improved cement of higher quality and enhanced properties such as permeability, porosity, mechanical and rheological properties. Very few researches have discussed the uses of …

Surface Characterization Of Particulate Dust Subjected To Dew-Induced Cementation, Mohamed Adawi

Student Theses and Dissertations

Accumulation of soils and other particulate matter on the front cover glass of solar photovoltaic (PV) modules results in transmission losses that detrimentally affect the power output of PV installations. Cementation reactions occur due to interactions between the dust and the glass surface in the presence of temperature, humidity, and ph. In this study, accelerated soiling and cementation tests on glass coupons were performed using a custom instrumented soiling chamber and several standardized soils (Arizona Test Dust, Aramco Test Dust, and China Test Dust) to assess soil adhesion and cementation behaviors. Water contact angle (WCA) and X-ray photoelectron spectroscopy (XPS) …

Me-Em Enewsbrief, December 2022, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Electromagnetic Theory And Applications, Nicholas Madamopoulos, George Kliros

Open Educational Resources

This book intends to provide both the fundamentals of Electromagnetics but also some practical applications of the concepts covered. Having taught electromagnetics for several years, the authors feel that many times the field of electromagnetics comes as “old” and often times students do not appreciate the concepts and their importance in everyday applications. The authors intend to accompany the EM concepts with life applications. Hence, students may see the direct impact of the knowledge they acquire through the study of the field of electromagnetics and better appreciate the field.

Recent Advances In Exploring Highly Active & Durable Pgm-Free Oxygen Reduction Catalysts, Yuan Li, Miao-Ying Chen, Bang-An Lu, Jia-Nan Zhang

Journal of Electrochemistry

In order to reduce the considerable usage of expensive but scarce platinum at the cathode in proton exchange membrane fuel cells (PEMFCs), it is necessary to pursue alternatives to platinum. The most promising platinum group metal (PGM)-free catalysts for oxygen reduction reaction (ORR) are atomically dispersed, and nitrogen-coordinated metal site catalysts denoted as M-N-C (M = Fe, Co, or Mn, etc.). Over the last few decades, there have been great advances in these catalysts with high ORR activity and promising initial fuel cell performance approaching traditional Pt/C catalysts. However, the stability of these highly active Fe-N-C catalysts under practical fuel …

Preface To Special Issue: Electrocatalysis And Electrosynthesis, Fang-Yi Cheng, Shuang-Yin Wang, Tian-Hua Zhou

Journal of Electrochemistry

No abstract provided.

Electrochemical Oxidation Of Ethylene On Palladium Electrode, Wei-Xing Wu, Ying Wang

Journal of Electrochemistry

The electrochemical oxidation of C₂H₄ is attracting increasing attention due to its vast potential market. The current electrochemical methods rely on the use of redox mediators, which may produce corrosive intermediates, while direct oxidation is still limited by its low activity and selectivity. Herein, we conducted electrochemical studies to obtain mechanistic insights into the benchmark Pd catalyst. The generated Pd(II) could be the active site for C₂H₄ oxidation. By designing the pulse sequence, we found the ratio of strongly and weakly adsorbed C₂H₄ on Pd to be 0.3:1. The result we …

Supperlattice-Like Structure: Ordered Mass Transfer Endowing High Quality Output Of Fuel Cell, Jian Wang, Wen-Hui Xuan, Qian He, Jing-Xia Jiang, Yuan-Yuan Zhou, Yao Nie, Qiang Liao, Min-Hua Shao, Wei Ding, Zi-Dong Wei

Journal of Electrochemistry

The current or voltage fluctuation in fuel cell operation is harmful to the fuel cell system and power application equipment. Here, we report a technique to eliminate such a fluctuation by the aid of new type of catalysts, superlattice-like mesoporous PtCo catalysts. The current fluctuation in fuel cells catalyzed by two invented catalysts are fixed at as low as 25 mA·cm⁻² with a power of 0.75 W·cm⁻² or 120 mA·cm⁻² with a power of 1.01 W·cm⁻², and no noticeable current decay was detected over 100 h. By contrast, a …

First-Principles Molecular Dynamics Study Of Liquid Iron-Rich Alloys Under Conditions Of The Earth’S Core, Dipendra Banjara

LSU Doctoral Dissertations

In this dissertation, we report the results of the first-principles molecular dynamics (FPMD) simulations and data analysis on the thermodynamic, structural, and transport properties of iron-rich metallic liquids considering several light and heavy elements under wide ranges of pressure and temperature that are relevant to the earth’s core. Our simulations of pure liquid iron cover the pressure range from 0 GPa at 2000 K to 380 GPa at 7000 K perhaps representing the most extensive computational study to date. We studied four molten iron-rich alloys corresponding to 2.67 atom% of Ni, Co, Mo, and W at pressures up to 380 …

Neutralization Of Fuel Tankering Emissions For Environmental Sustainability, Peter O'Reilly, Maria Petrescu, Fabricio Sulzbacher, Diogo Coutinho

National Training Aircraft Symposium (NTAS)

As aviation has been one of the fastest-growing sources of emissions, this paper explores sustainable solutions in the equation of the economic savings from the fuel tankering practice, in a way it could represent gains of credibility for this industry (Boussauw & Vanoutrive, 2019). The fuel expenses in Brazil have been responsible for the highest operational cost for the airlines and, as a result, there has been an ongoing pursuit of the highest level of efficiency (ANAC, 2019). In this context, this study has been focused on the emerging Brazilian aviation market, and uses primary data collected from three major …

Interfaces In Dynamic Brittle Fracture Of Pmma: A Peridynamic Analysis, Longzhen Wang, Javad Mehrmashhadi, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

Recent experiments in bonded PMMA layers have shown dramatic changes in dynamic crack growth characteristics depending on the interface location and toughness. In this paper we present a peridynamic (PD) analysis of this phenomenon and determine three elements that are essential in a model reproducing the observed fracture behavior: (1) softening near the crack tip to account for changes in PMMA due to heat-generation induced by the high strain rates reached around the crack tip in dynamic fracture; (2) independent extension (mode I) and shear (mode II) modes of fracture; (3) a two-parameter fracture model, which matches both strength and …

Effect Of Blank Moisture Content On Forming Behaviour And Mechanical Properties Of Paperboard Tray Packages, Arvo Niini, Lena Berthold, Tobias Müller, Panu Tanninen, Jens-Peter Majschak, Juha Varis, Ville Leminen

Journal of Applied Packaging Research

Tray blanks were moisturised to study the effect of different blank moisture content levels on forming behaviour and mechanical properties of paperboard tray packages. The blank moisturisation was done by spraying water to the blanks before their three-dimensional (3D) forming. The trays were 3D formed by press forming or deep drawing. Visual quality and punch force values were used as indicators to evaluate the forming behaviour of the trays. The mechanical properties of the trays were investigated with compression, torsion, and storing tests. A high blank moisture content reduced the punch force, and the elevated blank moisture was connected to …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …

Locally Resonant Metasurface For Low-Frequency Transmissive Underwater Acoustic Waves, Zhong Chen, Shenghong Guan, Qiang Xie, Zheng Li, Zhongmei Gao, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Acoustic metasurfaces for underwater wave manipulation have great potential use, but the strong solid-fluid interaction caused by impedance closeness between the structure and water brings design difficulty, especially in the low-frequency range.

Methods: Here a locally resonant metasurface for transmissive underwater acoustic waves is proposed using finite element method for which each metasurface unit consists of one channel and three subunits. Each subunit has one plate and two rubber spacers to form a resonator. By changing the height ratio of the plate over the subunit, arbitrary phase shifts within the full 2π coverage can be obtained at …

Rc Baja Suspension And Steering, Garrett Bailey

All Undergraduate Projects

The RC Baja team set out to engineer and construct a working remote-control device that can compete in the ASME Baja Competition. The students have a focus on either suspension and steering or drivetrain and chassis. This report is centered on the suspension and steering. First, multiple analyses were completed using engineering methods such as mechanical design, statics, strengths of materials, and dynamics for parts of the device. The calculations found in the analysis are then used to create designs for the parts so that they will meet the requirements and be successful in the competition. After the parts are …

Survey Data: Optimising Retrofitted Insulation For Irish Residential Building Walls, Rakshit D. Muddu, Aimee Byrne, Anthony Robinson Dr.

Datasets

A survey was conducted to determine the preferred set point temperature and heating pattern among Irish households. The survey was sent to 237 people living across Ireland, out of which 32 respondents skipped the survey and 9 surveys were found to be incomplete. Amongst the counties in Ireland 71.1% respondents were from Dublin, 6.34% from Kildare, 5% from Meath, 5% from Wicklow and in all the remaining counties response rate was below 2%. Part 1: This section of the survey recorded information regarding characteristics of the building such as house type, wall type, insulation type, period the house was built. …

Internal Structure And Breakage Behavior Of Biogenic Carbonate Sand Grains, Elieh Mohtashami, C. Guney Olgun, Chenglin Wu, Tara Selly

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Study Investigates the Mechanical Behavior of Biogenic Carbonate Sands from Puerto Rico at Grain-Scale Level. Micro-Computed Tomography Has Also Been Used to Get Insights on the Internal Structure of These Particles Before and after Loading. the Crushing Strength of These Particles Are Smaller Comparing to the Values Reported for Silica Sands. It Has Also Been Shown that These Particles Have Complex Internal Structure Including a Network of Pores Connected with Channels. This Study Also Demonstrates the Effect of Intragrain Structure of Biogenic Carbonate Sands and Shows How Internal Grain Structure Plays a Role on Particle Fracture.

Direct Ink Write Processing Of Signal Crossovers Using Aerosol Jet Printing Method, Lucas A. Clark

Browse all Theses and Dissertations

Electronics in different applications, such as in medical imaging devices, radar systems, communication transmitters, and optical drives, often require various power and signal lines to be integrated at board level. In such cases, different lines may cross over one another in three-dimensional space for efficient electronic integration. Crossovers are usually achieved by adding additional layers to a PCB. However, these additional layers increase the cost, weight, and complexity of the component. By creating a process and structure to offer board-level heterogenous integration, these factors may be reduced. RF-DC crossovers were designed and additively manufactured using an aerosol jet printer. Benzocyclobutene …

An Efficient And Low-Cost Method To Create High-Density Nitrogen-Vacancy Centers In Cvd Diamond For Sensing Applications., Prem Bahadur Karki, Rupak Timalsina, Mohammadjavad Dowran, Ayodimeji E. Aregbesola, Abdelghani Laraoui, Kapildeb Ambal

Department of Mechanical and Materials Engineering: Faculty Publications

The negatively charged Nitrogen-Vacancy (NV^-) center in diamond is one of the most versatile and robust quantum sensors suitable for quantum technologies, including magnetic field and temperature sensors. For precision sensing applications, densely packed NV^- centers within a small volume are preferable due to benefiting from 1/√𝑁 sensitivity enhancement (N is the number of sensing NV centers) and efficient excitation of NV centers. However, methods for quickly and efficiently forming high concentrations of NV^- centers are in development stage. We report an efficient, low-cost method for creating high-density NV^- centers production from a relatively …

Correction: Nanoscale Imaging Of Antiferromagnetic Domains In Epitaxial Films Of Cr2o3 Via Scanning Diamond Magnetic Probe Microscopy, Adam Erickson, Syed Qamar Abbas Shah, Ather Mahmood, Ilja Fescenko, Rupak Timalsina, Christian H. Binek, Abdelghani Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

Correction for ‘Nanoscale imaging of antiferromagnetic domains in epitaxial films of Cr2O3 via scanning diamond magnetic probe microscopy’ by Adam Erickson et al., RSC Adv., 2023, 13, 178–185, https:// doi.org/10.1039/D2RA06440E