Engineering Science and Materials Commons^™

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

Effect Of Multiple Machine Configurations And Wall Thickness On Microstructure And Microhardness Of Laser Powder Bed Fusion (L-Pbf) Additively Manufactured Heat-Treated Inconel 718 Products, Anannya Doris

Open Access Theses & Dissertations

This research examined thin section prototypes having seven nominal thicknesses ranging from 0.1 to 2.0 mm, composing a series of geometric feature build plates manufactured by multiple laser powder bed fusion (L-PBF) machine configurations. The build plates and thin section feature prototypes underwent a full heat treatment cycle per established standards: anneal at 1066°C, SR+HIP at 1163°C, and fully treat-treated by combining SR+HIP+solution treatment at 1066°C and double aging treatment at 760°C and 680°C, respectively. The fully heat-treated (FHT) Inconel 718 wall specimens were sectioned from 16 distinct geometric feature build plates constructed on 15 different L-PBF machines. The thin …

Ultra Wide Band Gap Oxides For Advanced Optoelectronics And Supercapacitor Applications: A Case Study Of Intrinsic And Doped Germanium Dioxide, Paul Gaurav Nalam

Open Access Theses & Dissertations

Germanium dioxide (GeO2) is a metal oxide semiconductor with multiple polymorphs that has recently garnered a significant amount of scientific attention owing to its novel ultra-wide band gap and pseudo-capacitive properties, which can potentially transcend current power electronic, optoelectronic, and supercapacitor technologies. However, due to the difficulty in the synthesis of stable crystalline phases of individual polymorphs of GeO2 thin films, this material system demands complex and resource-intensive deposition techniques to synthesize. An attempt was made to develop cost-effective and scalable deposition techniques to stabilize specific crystalline phases of GeO2 thin films. These phases were further structurally fine-tuned to state …

Ultrasonic Non-Destructive Evaluation Of Additively Manufactured Polymer-Ceramic Composites, Christian Alexander Ruiz

Open Access Theses & Dissertations

Digital light processing (DLP) is an attractive additive manufacturing technique due to its ability to create ceramic parts with complex geometries. DLP uses ultraviolet light to polymerize a slurry comprised of ceramic powder and photosensitive resin in layers to create solid parts. Printing parameters such as light intensity and exposure time are critical when producing these parts. Improper parameters can lead to over or under-curing, adversely impacting print quality and strength. Samples were printed at varying layer exposure times and then tested using ultrasonics to determine the degree of conversion. Additionally, ultrasonics were used as a non-destructive technique to obtain …

Development Of A 3d Printed Conductive Biopolymer For Cardiac Tissue Engineering, Britanny Lizeth Stark

Open Access Theses & Dissertations

Cardiovascular disease (CVD) is the leading cause of death in the US, with approximately 859,000 deaths each year. The major contributor to CVD is Acute Myocardial Infarction (AMI), which causes the death of approximately 25% of the cardiomyocytes present in the left ventricle of the heart. After AMI, the adult human heart has a very limited regenerative capacity. Moreover, the electrical propagation of the myocardium is severely disrupted, making the heart more susceptible to failure and patient death. However, current pharmacological treatments do not address the loss of cardiomyocytes and the disruption of electrical propagation in the heart. Tissue engineering …

Characterization Of Fcc Al-Cu-Ni-Mn-Ag High Entropy Alloy, Gina Zavala Alvarado

Open Access Theses & Dissertations

The effect of Ag on the microstructure developed in Al-Cu-Ni-Mn alloy has been determined. The modified Al-Cu-Ni-Mn alloy by Ag addition shows the presence of three microconstituents consisting of phases rich in (1) Cu, (2) Ni, and (3) Ag. The foregoing alloys heated for 24 hours from 600 to 1000 °C show excellent oxidation resistance. Oxide formation and microstructural changes of the alloy have been characterized by elemental mapping and X-ray diffraction (XRD). Results show that the elements of Al and Mn preferentially oxidize while Cu and Ni provide oxidation resistance to the alloy. Hardness was taken on the alloy …

Upcyclying Of Polyethylene Terephtalate By Addition Of Thermoplastic Elastomer, Diego Francisco Bermudez

Open Access Theses & Dissertations

Continual overconsumption of single-use plastics has generated challenges of solid waste management across the United States. Common plastic waste management solutions, such as landfill, have caused the migration of contaminants into the environment consequently affecting not only the health of wildlife, but also that of human beings. Alternative strategies for the handling of single-use plastic such as polyethylene terephthalate (PET), used in the food packaging industry, can ultimately help mitigate the noxious consequences of single-use plastics affecting entire ecosystems. This study demonstrates a potential avenue of materials upcycling by studying the effects of coupling PET with the thermoplastic elastomer styrene-ethylene-butylene-styrene …

Initiation Criteria For The Onset Of Geomagnetic Substorms Based On Auroral Observations And Electrojet Current Signatures, Mayowa Michael Kayode-Adeoye

Graduate Theses and Dissertations (2019 - present)

In recent years, several substorm onset criteria have been developed, either from auroral observations (many authors) or from auroral electrojet properties such as those described by (Forsyth et al., 2015; Maimaiti et al., 2019; Newell & Gjerloev, 2011; Partamies et al., 2011) The different criteria are being investigated using a low order physics model of the magnetosphere called WINDMI (Spencer et al., 2009) and inferences are being made in line with the WINDMI model. The model variables will be compared with the criteria for substorm onset proposed by examining the SML index.

The WINDMI model uses solar wind and IMF …

Analyzing The Effects Of Ultrafast Laser Processing On Mechanical Properties Of 3d-Printed Pla Parts, Darshan Pramodbhai Yadav

Theses and Dissertations

Recent advances in additive manufacturing technologies have already led to wide-scale adoption of 3D-printed parts in various industries. The expansion in choice of materials that can be processed, particularly using Fused Deposition Modeling (FDM), and the steady advancements in dimensional accuracy control have extended the range of applications far beyond rapid prototyping. However, additive manufacturing still has considerable limitations compared to traditional and subtractive manufacturing processes. This work addresses limitations associated with the as-deposited surface roughness of 3D-printed parts. The effects of roughness-induced stress concentrations were studied on ultimate tensile strength and fatigue life. The samples were manufactured using a …

Study On Effect Of 3d Printing Parameters On Surface Roughness And Tensile Strength Using Analysis Of Variance, Faqih Fadillah, Heru Suryanto, Suprayitno Suprayitno

Journal of Mechanical Engineering Science and Technology (JMEST)

Fused deposition modeling of 3D printing is the process of making workpieces or parts by adding filaments to each layer. Some indicators of a high-quality product of 3D printing are the precisions dimensions, the surface roughness, and tensile strength. This research aims to find the parameters most affecting surface roughness and tensile strength. The research design used an experimental method with input parameters: (1) print speed (15-35 mm/s), (2) print temperature (200-210C), (3) layer height (0.1 – 0.3 mm), (4) infill line directions (0-90), and dependent variables were surface roughness and tensile strength. The data distribution used the L9 orthogonal …

Mechanical Characterization Of Naoh-Treated Agel Fiber-Cotton Composites, I Gusti Ngurah Nitya Santhiarsa, I Gusti Bagus Wijaya Kusuma, I Gede Artha Negara

Journal of Mechanical Engineering Science and Technology (JMEST)

Composites comprising two or more distinct materials are fabricated to enhance the mechanical properties of the constituent materials. A common approach for generating composites is vacuum infusion. This technique enables the infusion of two materials utilizing a vacuum. In the field of composite science, textile composites have emerged as an important new development. Agel rope, derived from twisting agel fibers, exhibits inferior bending strength and elongation compared to ropes fabricated from synthetic fibers. Moreover, agel rope is susceptible to bacterial decay. This study aims to characterize the mechanical properties of textile composites comprising woven agel rope subjected to NaOH treatment. …

Heat Conduction In Cylindrical Coordinates With Time-Varying Conduction Coefficients: A Practical Engineering Approach, Lulut Alfaris, Ruben Cornelius Siagian, Aldi Cahya Muhammad, Ukta Indra Nyuswantoro, Budiman Nasution

Journal of Mechanical Engineering Science and Technology (JMEST)

This research aims to develop a mathematical method for expressing the Laplace operator in cylindrical coordinates and applying it to solve heat conduction equations in various scenarios. The method commences by transforming Cartesian coordinates into cylindrical coordinates and identifying the necessary substitutions. The result is the expression of the Laplace operator in cylindrical coordinates, which is subsequently employed to address heat conduction equations within cylindrical coordinates. Various cases encompassing different initial and boundary conditions, as well as variations in the conduction coefficient over time, are meticulously considered. In each instance, precise mathematical solutions are determined and subjected to thorough analysis. …

Numerical Study On Resistance Of Stepped Planing Hull, Fajri Ashfi Rayhan, Andika Masrul, Arya Khairullah Akbar, Bima Anugerah Putra

Journal of Mechanical Engineering Science and Technology (JMEST)

A stepped planing hull, also known as a step hull, is a hull modification that reduces the wetted surface area. Although this type of hull has proven effective in several ships, it is still rarely used. The step hull possesses numerous advantages that make it ideal for activities involving small and fast boats. However, regrettably, its full potential remains untapped at present. The purpose of this study was to identify the effect of variations in the angle of the step hull on resistance or drag. The study utilized the CFD method, and three hull configuration models were used at each …

Analyzing Transition Metallic Catalytic Converter Impact On Four-Stroke Motorcycle Fuel Consumption, Sudirman Rizki Ariyanto, Ata Syifa’ Nugraha, Wahyu Robby Cahyadi, Yelma Dianastiti, Muhammad Yandi Pratama

Journal of Mechanical Engineering Science and Technology (JMEST)

Increased exhaust emissions from motor vehicles have become a major concern in efforts to reduce air pollution. One developed solution is the use of transition metallic catalytic converter (TMCC) technology in vehicle exhaust systems. This study aims to compare the fuel consumption efficiency of three types of exhaust systems, namely standard exhaust without a catalyst (STD WC), the standard exhaust with Original Equipment Manufacturer catalyst (STD OEM), and an exhaust system equipped with a Copper-Coated Chrome Metallic Catalytic Converter (TMCC CuCr). The data analysis method employed a quantitative approach by collecting fuel consumption data at each rpm and analyzing the …

Effect Of The Homogenization Process On Titanium Oxide-Reinforced Nanocellulose Composite Membranes, Taufiq Mahsuli, Aisyah Larasati, Aminnudin Aminnudin, Jibril Maulana

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesian pineapple production can reach 200 tons per day; however, pineapples generate a significant amount of waste. Pineapple peel waste can be used to make membranes. Composite membranes containing TiO2 have dense properties, low porosity, and increase the mechanical strength of the cellulose sheet. This research uses various ultrasonic homogenizers to homogenize the distribution of nanocellulose and TiO2 (50% and 100% power with 30, 60, and 90 minutes). The casting method is used to shape the membrane. The SEM test shows that the higher the power used and the longer the sonication time, the less agglomeration of about 1.63%/ cm2 …

Effect Of Heating Temperature, Holding Time And Stabilization Temperature On The Al-Foam Properties, Dewi Puspitasari, Poppy Puspitasari, Mazli Mustapha, Turnad Lenggo Ginta

Journal of Mechanical Engineering Science and Technology (JMEST)

The interest in metallic foam is increasing since their cellular structures have a unique combination of properties such as high stiffness, low density, lightweight, high specific strength, and thermal insulation. Commonly, the performance of metallic foam can be improved by the heat treatment process. However, the previous heat treatment methods still present the brittle crack path and the research on heat treatments of the metal foam properties is very limited. In this study, individual parameters in stress relieving treatment that contribute to Al-Foam properties were investigated. The stress-relieving process of the samples was performed using a vacuum furnace. The composition …

Vertical Shaft Kinetic Turbine Performance Using A Cup-Shape Blade, Kennie A. Lempoy, Nita C. V. Monintja, Arwanto M. A. Lakat

Journal of Mechanical Engineering Science and Technology (JMEST)

The abundant availability of alternative energy sources forms the fundamental foundation for rural energy development. In particular, renewable energy sources are indispensable in rural areas due to their ecofriendly nature and widespread accessibility, which helps preserve the environment by avoiding pollution. Indonesia, a country blessed with vast water resources, especially its rivers, holds enormous potential for harnessing kinetic energy derived from fast-flowing river waters. Effective utilization of this kinetic energy has the potential to address energy shortages in the country. In this context, there is a pressing need to enhance the efficiency of kinetic turbines designed to function as electricity …

Photocatalytic Scheme With External Magnetic Field On Coffee Waste In Hydrogen Production, Abid Fahreza Alphanoda, Eko Prasetyo, Wisnu Broto

Journal of Mechanical Engineering Science and Technology (JMEST)

Photocatalytic is considered a deadlock-breaking technology for renewable energy and lowering environmental pollutants. Photocatalytic efficiency efforts are improved by activating the photocatalyst to introduce an external magnetic field. This review highlights recent breakthroughs by comparing original coffee waste, activation of coffee waste with the addition of catalysts, and manipulation of spin electrons by applying external magnets. Characterization was done with FTIR to look at chemical bonds, UV-Vis with Tauc's Relation approach to measure bandgap, and material morphology using SEM EDX. The increase in photocatalyst activation aligns with the decrease in bandgap value. The rate of decline in bandgap is in …

Artificial Neural Network-Based Modeling Of Performance Spark Ignition Engine Fuelled With Bioethanol And Gasoline, Susi Marianingsih, Farhanna Mar’I, Hendry Y. Nanlohy

Journal of Mechanical Engineering Science and Technology (JMEST)

Machine learning technology can distinguish the relationship between engine characteristics and performances. Therefore, the goal of the present work is to predict the performance parameters of a singlecylinder 4-stroke gasoline engine at different ignition timings using a blended mixture of gasoline and bioethanol by an artificial neural network (ANN). Experimental data for training and testing in the proposed ANN was obtained at a dynamic speed and full load condition. An ANN model was developed based on standard Back-Propagation algorithm for the spark ignition engine. Multi-layer perception network (MLP) was used for non-linear mapping between the input and output parameters. An …

The Effect Of Adding Aluminium On The Performance Of Zno Nrs/Pani In Their Application As Photoelectrochemical Water Splitting, Eprilia Trikusuma Sari, Nandang Mufti, Anissa Chairani Alfin Nadhira, Hari Wisodo, Markus Diantoro

Journal of Mechanical Engineering Science and Technology (JMEST)

Photoelectrochemical (PEC) is a new renewable energy technology that converts H2O into hydrogen and oxygen gas with the help of sunlight. A photoelectrochemical cell device consists of three main components, one of which is the photoanode. One of the materials that can be used as a photoanode is ZnO which has good electrical properties and is non-toxic. Nanorods-structured ZnO has the advantage of being able to increase light absorption due to its high surface area. However, the resulting performance is still quite low. So it is necessary to make modifications to the photoanode, one of which is by adding aluminium …

Preparation And Lithium Storage Properties Of Carbon Confined Li3Vo4 Nano Materials, Jia-Qi Fan, Huan-Qiao Song, Jia-Ying An, Amantai A-Yi-Da-Na, Mo Chen

Journal of Electrochemistry

Li₃VO₄, as a promising anode material for lithium ion batteries, has been widely studied because of its low and safe voltage, and large capacity. However, its poor electronic conductivity impedes the practical application of Li₃VO₄ particularly at high rates. In this paper, carbon confined Li₃VO₄ nano materials (Li₃VO₄/C) were synthesized by hydrothermal and solid-phase method, and for comparison, the Li₃VO₄ (N) nano materials without carbon confinement and Li₃VO₄ (B) materials were also synthesized by pure solid-phase method. The composition, structure, …

Peg-Water Electrolyte For High-Performance Zinc Iodine Dual-Ion Batteries, Xiao-Feng Qu, Yu-Ting Tang, Xin-Cheng He, Jia-Sheng Zhou, Zi-Heng Tang, Wen-Hua Feng, Jun Liu

Journal of Electrochemistry

Thanks to abundant resource and rapid redox reaction kinetics, iodine is regarded as promising positive materials inthe batteries. However, the shuttling effect due to the high solubility of iodine in the electrolyte makes the performance of battery poor. In this paper, polyethylene glycol (PEG400) and potassium iodide were added into zinc-ion aqueous electrolyte. PEG400 could complex with iodine to reduce the dissolution of iodine, therefore alleviating the formation of soluble triiodide (I₃^–) from iodine and iodide ions. Furthermore, this electrolyte was used in the battery with double carbon cloths as the current collectors, double separators and zinc …

Lif-Sn Composite Modification Layer To Modify Garnet/Lithium Metal Interface, Wu Yang, Xue-Fan Zheng, Yu-Qi Wu, Zheng-Liang Gong

Journal of Electrochemistry

The growing demands for electric vehicles and consumer electronics; as well as the expanding renewable energy storage market; have promoted extensive research on energy storage technologies with low costhigh energy density and safety. Lithium (Li) metal and solid-state electrolytes are considered as important components for next-generation batteries because of their great potential for improvements in energy density and safety performance. Inorganic garnet-type solid electrolytes with high Li-ion conductivity (about 10^-3 S·cm^-1) and high shear modulus (55 GPa) are considered to be ideal solid-state electrolytes; however; the issue of Li dendrite growth still obstructs their practical application. Herein; …

Constructing Carbon-Encapsulated Nifev-Based Electrocatalysts By Alkoxide-Based Self-Template Method For Oxygen Evolution Reaction, En-Hui Ma, Xu-Po Liu, Tao Shen, De-Li Wang

Journal of Electrochemistry

The development of green and sustainable water-splitting hydrogen production technology is beneficial to reducing the over-reliance on fossil fuels and realizing the strategic goal of "carbon neutral". As one of the half reactions for water splitting, oxygen evolution reaction has suffered the problems of sluggish four-electron transfer process and relatively slow reaction kinetics. Therefore, exploring efficient and stable catalysts for oxygen evolution reaction is of critical importance for water-splitting technology. Metal alkoxides are a series of compounds formed by the coordination function of metal ions with alcohol molecules. Metal alkoxides possess the double advantages of organic materials and inorganic materials, …

What Does It Mean To Be “Prepared For Work”? Perceptions Of New Engineers, Jessica R. Deters, Marie C. Paretti, Logan A. Perry, Robin Ott

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Engineering education seeks to prepare students for engineering practice, but the concept of preparedness is often ill-defined. Moreover, findings from studies of different populations or in different contexts vary regarding how well new graduates are prepared. These variations, coupled with the lack of clarity, suggest the need to better understand what it means to be prepared for engineering work.

Purpose: This study contributes to research on workplace preparation by exploring how new graduates describe being prepared for engineering work.

Method: Applying secondary analysis to data from the multi-institution Capstone To Work (C2W) project, we used thematic …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

Meta-Analysis Of Insulated Concrete Wall Panel Design Methods For Shear And Flexure Behavior, Maryam Al-Bayati

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Insulated Concrete wall panels have been designed and constructed since the early 1950s with various shear ties, dimensions, and methods; nonetheless, thermal bridging and rational design are still a concern. Many companies have recently developed plastic connectors that have gradually replaced solid concrete sections and steel connectors due to their superior thermal efficiency and strength. However, there is no generally accepted method for predicting the behavior of sandwich wall panels in structural engineering practice or codes, but many methods have been used since the early 1920. This study aims to evaluate the accuracy of current methods for predicting the flexural …

Impact Of Silicon Ion Irradiation On Aluminum Nitride-Transduced Microelectromechanical Resonators, David D. Lynes, Joshua Young, Eric Lang, Hengky Chandrahalim

Faculty Publications

Microelectromechanical systems (MEMS) resonators use is widespread, from electronic filters and oscillators to physical sensors such as accelerometers and gyroscopes. These devices' ubiquity, small size, and low power consumption make them ideal for use in systems such as CubeSats, micro aerial vehicles, autonomous underwater vehicles, and micro-robots operating in radiation environments. Radiation's interaction with materials manifests as atomic displacement and ionization, resulting in mechanical and electronic property changes, photocurrents, and charge buildup. This study examines silicon (Si) ion irradiation's interaction with piezoelectrically transduced MEMS resonators. Furthermore, the effect of adding a dielectric silicon oxide (SiO₂) thin film is …

A Review On The Coalescence Of Confined Drops With A Focus On Scaling Laws For The Growth Of The Liquid Bridge, Sangjin Ryu, Haipeng Zhang, Udochukwu John Anuta

Department of Mechanical and Materials Engineering: Faculty Publications

The surface–tension-driven coalescence of drops has been extensively studied because of the omnipresence of the phenomenon and its significance in various natural and engineering systems. When two drops come into contact, a liquid bridge is formed between them and then grows in its lateral dimensions. As a result, the two drops merge to become a bigger drop. The growth dynamics of the bridge are governed by a balance between the driving force and the viscous and inertial resistances of involved liquids, and it is usually represented by power–law scaling relations on the temporal evolution of the bridge dimension. Such scaling …

Revealing Interface-Assisted Plastic Anisotropy Via In Situ Transmission Electron Microscopy Tension Of Lamellar Tial, Zhixiang Qi, Qi Zhu, Jian Wang, Yuede Cao, Fengrui Chen, Jiangwei Wang, Yang Chen, Gong Zheng, Guang Chen

Department of Mechanical and Materials Engineering: Faculty Publications

Assembling functional units into specific orientation organizations based on functional unit and organization (FUO) paradigm can maximize utilizing mechanical property anisotropy of lamellar-structured materials. However, the origin of their anisotropic deformation behaviors has not been clearly understood. Taking the fully lamellar γ-TiAl/ α₂-Ti₃Al dual-phase single crystal as an example, we decouple the interface functional units governed anisotropic plastic deformation through in situ transmission electron microscopy tensile testing and multiscale microstructural characterizations. The orientation organization-dependent slip continuity across the γ/α₂ interface and interface strength play a determinant role in plastic anisotropy beyond intrinsic dislocation activities within …