Engineering Science and Materials Commons^™

Study On Carbon From Pyrolyzing Phenol-Formaldehyde Resin For The Negative Electrode Of Li-Ion Secondary Battery, Zhi-Yuan Tang, Xin-Guo Zhuang, Yu-Mei Zhai, Jian-Gang Li, Jian-Jun Xue, Chun-Yan Liu

Journal of Electrochemistry

Li-ion secondary batteries negative electrodes were prepared by low temperature (<1 000 ℃) pyrolysis of commercial phenol-formaldhyde resin. A thermogravimetric analysis (TGA) and an X-ray diffraction (XRD) studies were peoformed for the pyrolytic carbonaceous materials. The results indicated that these samples are amorphous polyacenic structure materials. With increasing pyrolytic temperature, these materials become structurally order, and the first charge-discharge special capacities reduce. The specific capacities base on pyrolytic temperature, involving lithium storage nanometer cavities.

Preparation And Characteristics Of A Enzyme Electrode Based On Immobilization Of Tyrosinase In Electropolymerized Polypyrrole Film, Liu-Shui Yan, Qia Wei, Cheng-Yi Wang, Rong-Rong Shi, Xiao-Tong Ma

Journal of Electrochemistry

A sensitive and stable amperometric enzyme electrode was constructed, based on the immobilization of tyrosinase in potentiostatically electropolymerized polypyrrole film at a platinum electrode. The influence of pH and potential on immbilization was discussed. SEM micrographs and CV curves of films obtained before and after incorparation of tyrosinase molecular were analyzed and compared each other. The enzyme electrode responds linearly to p-cresol over a concentration range of 5×10 -8 ～1×10^-6 mol/L with an optimum pH of 6.6, It exhibited kinetic characteristics of the typical enzyme-catalyzed reaction with an apparent Michaelis constant of 2.2 ×10^-5 mol/L.

An Investigation On The Corrosion Potential Imaging At The Interface Of Concrete/Reinforcing Bar In Corrosion Media, Rong-Zong Hu, Chang-Jian Lin, Xiang Zhou, Jian-Guang Tan, Xiong-Chao Zhao

Journal of Electrochemistry

The iron array electrode covered with concrete as a new electrochemical technique is applied to map the potential imaging and to investigate on the iron electrode corrosion process under concrete: In Cl^_- solution the corrosion of the iron array electrode covered with concrete had been prevented for a short term since the concrete protection, but the corrosion still occurreed and developed after immersed for a long time. In SO₄^2- solution although the sample had being immersed for a long time and the concrete was possibly broken, the corrosion did not develop. In Cl^_- solution the corrosion …

Template Synthesis And Uv-Vis Absorption Spectra Of The Nanowire Arrays Of Cadmium Chalcogenides, Shi-Min Xu, Kuan-Hong Xue, Jing-Lin Kong, Dong-Mei Sun, Yu-Ying Feng, Hai-Yan Lu, Guang-Hou Wang

Journal of Electrochemistry

The porous alumina membrane formed in the anodic oxidation of highly pure aluminum foil has attracted a great deal of attention in recent years. It can be served as a desired template to prepare nanometer scale materials due to its unique structure of discrete and cylindrical nanopores, paralleled one another, with the homogeneous size and distribution. Chalcogenide semiconductors have promising prospect in the applications of photovoltaic and photoconducting devices and have been extensively exploited for many years. Olbright and his co-workers studied experimentally and theoretically the optical nonlinearties of CdS_xSe_1-x-doped glass; Britt and Ferekides reported that …

Electrochemical Quartz Crystal Microbalance Study On The Promoted Electron Transfer Process At Gold Electrode, Xia-Qin Wu, Zhe-Su Wang, Xiao-Yun Meng, Zong-Rang Zhang

Journal of Electrochemistry

The adsorption behavior of amino acids, such as L-cysteine, histidine and arginine at gold-quartz crystal microbalance (Au-QCM) was investigated. The adsorption quantity of cysteine is more appreciable than others because of the stronger interaction between its thiol group and the gold electrode surface. The electron-transfer process of superoxide dismutase (SOD) in presence of cysteine at Au-QCM has also been studied using the electrochemical quartz crystal microbalance (EQCM) technique which reveals clearly the quasi-reversible electron-transfer process accompanied by the frequency shift cycle. The reversible adsorption and disorption processes are discussed.

Effects Of Temperature On The Proton Diffusion Of Doped Ni(Oh)2, Jian-Hua Liu, Jing-Wu Yang, Zhi-Yuan Tang

Journal of Electrochemistry

The Chronoamperometry of powder spherical Ni(OH)₂ microelectrode was used to study the proton diffusion coefficients of Ni(OH)₂. The proton diffusion coeefficients and the apparent diffusion active energy in anode and cathode processes at different temperature were obtained. Compared with pure Ni(OH)₂, the apparent diffusion active energy (E_a) of Ni(OH)₂ doped with Co and Co + Zn was decreased and the diffusion constant (D_o) was increased in the anode and the cathode processes, respectively, the effect of Co was greater. In contrast, for Ni(OH)₂ doped with Zn, its E_{a …}

A Comparison Of Quasi-Static Indentation Testing To Low Velocity Impact Testing, Michael J. Douglas

Mechanical & Aerospace Engineering Theses & Dissertations

A static test method for modeling low-velocity foreign object impact events to composites would prove to be very beneficial to researchers since much more data can be obtained from a static test than from an impact test. In order to examine if this is feasible, a series of static indentation and low velocity impact tests were carried out and compared. Square specimens of many sizes and thicknesses were utilized to cover the array of types of low velocity impact events. Laminates with a rt/4 stacking sequence were employed since this is by far the most common type of engineering laminate. …

Finite Element Analysis Of A Composite Cylindrical Shell With A Cutout Under A Fatigue Load, Joshua T. Boatwright

Theses and Dissertations

A higher-order shell theory is used to analyze compressive and tensile loads on a graphite/epoxy laminated cylinder containing a square cutout. The Hashin failure criterion is used to determine failure in the fiber, matrix, or lamination. Once failure occurs, the appropriate stiffness terms are reduced. This failure causes a redistribution of stress, leading to further failure. In order to account for the loss of residual strength due to cyclic loading, the stiffness matrix is further reduced at each new increment of load or displacement. The objective is not to determine the S-N curve for the material, but rather to determine …

Mechanics Of A Functionally-Graded Titanium Matrix Composite, G. Brandt Miller

Theses and Dissertations

Functionally-graded Titanium Matrix Composites, (F/G TMCs) combine the ideal properties of titanium matrix composites with the more practical machining qualities of monolithic (unreinforced) alloy. This material shows great promise in application to aerospace structural components - even in parts whose design requirements have defied the use of composite materials in the past. Successful implementation of such a material would lead to enhanced aircraft performance. However, the basic properties of a functionally-graded titanium matrix composite need to be investigated. The composite/alloy transition region, or joint area, may be less strong than its constituents and therefore determine the overall performance of the …

Cathodic Indirect Electro-Oxidation——Organic Electro-Synthesis Dimethyl Sulfone, Deng-Ping Gu, Rui-Zhi Wang, Hong-Kun Zhang, Xue-Ying Zhang, Wei Li, Bao-Qiu Cui

Journal of Electrochemistry

A cathodic indirect electro-oxidation system was established for indirect electro-oxidize dimethyl sulfoxide to dimethyl sulfone with electro-eduction generated H₂O₂ catalyzed by the pertungstate/tungstate (WO₅^2-/WO₄^2-) redox mediator. Influences of current density, pH, temperature, and the current efficiencies etc. On the cathodic indirect electro-oxidation of dimethyl sulfone were investigated for determining optimum reaction conditions. The current efficiency reached more than 70%. Mother-liquid could be recycled to use without pollution.

Effect Of Different Species Of Cobalt Additive On Performance Of Nickel Hydroxide Electrode, Xian-Xia Yuan, Yin-Dong Wang, Feng Zhan

Journal of Electrochemistry

Performances of nickel electrodes when adding or without adding Cobalt in different forms were studied, the results were interpreted by cyclic voltammetry(CV) and electrochemical impedance spectroscope (EIS). It was demonstrated that the additions of Co, CoO, CoO+Co by mechanically mixing with Ni(OH)₂ all can improve the performance of nickel electrode to some extent, and when Co is added in the form of CoO the best performance can be obtained. This can be mainly attributed to the fact that three kinds of Co additives all improved the structure of nickel hydroxide and the ability of H⁺ in electrolyte transporting …

Studies Of Abnormal Infrared Effects Of Nanometer Thin Films Of Transition Metals And Alloys In Acid Solutions, Shi-Gang Sun, Ming-Sen Zheng, Guo-Qiang Lu, Li-Rong Cai, Sheng-Pei Cehn, Xiao-Yin Xiao

Journal of Electrochemistry

The adsorption of CO on electrodes of nanometer thin films of transition metals (Pt, Pd, Rh, Ru) and alloys (PtPd, PtRu) prepared under cyclic voltammetric conditions has been studied by in situ FTIR spectroscopy. The abnormal infrared effects (AIREs) have been explored as a novel and general phenomenon. The AIREs consist mainly in the inversion of the direction of IR band and the significant enhancement of IR absorption by adsorbed CO species. It was revealed that the enhanced IR absoroption of adsorbed species in AIREs depends strongly on the nature of metal or alloy, and on the structure and the …

Investigations Of Lithium Ion Battery Electrolyte Solution, Jing-Li Han, Qing-Guo Liu

Journal of Electrochemistry

Synthesis and electrochemical investigations of {LiB[(SO₃)C₆H₃(O)(COO)]OC₆H₅} in EC/DMC or DMSO/PC mixtures are presented.

The Study On Fabricating Thin Electrodes For Polymer Electrolyte Membrane Fuel Cells (Pemfc), Yong-Sheng Yang, Jing-Hua Liu, Chang-Peng Liu, Gong-Quan Sun, Chang-Zhi Li, Tian-Hong Lu

Journal of Electrochemistry

To lower platinum loading in electrodes for polymer electrolyte membrane fuel cell, a new thin electrode fabrication technique (TEFT) was developed in this work. A series of low Pt loading electrodes with smooth and uniformed surface were fabricated by the TEFT. As a result, the maximum power density of the cell with platinum loading of 1 mg/cm² and Nafion 117 membrane as electrolyte was up to 0.3 W.cm^-2. Moreover, the effects of PTFE and Nafion content in cathodes on the performance of PEMFC with low Pt loading electrodes (1 mg Pt/cm²) were examined systematically.

Sprayed And Thermally Evaporated Carbon Films As Anodes For Lithium Ion Batteries, Shu-Gao Zhang, M.Schleich Donald

Journal of Electrochemistry

Carbon films were made using spray-thermal evaporation from a kind of pyrolytic carbon powder. The films obtained with graphite structure were both potentio-statically and galvanostaically tested. Cycling patterns indicated a reduction peak on the first cycle corresponding to the formation of solid electrolyte interface, and the capacity values and x values were quite acceptable compared to theoretical ones when charging-discharging current density was suitable. Based on the experimental results, the obtained carbon films could be used as anode materials for relatively determining the electrochemical performances of cathode materials.

Studies On Electrochemical Synthesis Of 4,5-Disubstituted-1,2- Benzoquinones And The Reaction Mechanism, Xian-Zhang Bu, Gui-Wu Xiao, Lin Ma, Xing-Chum He, Ling-Quan Gu

Journal of Electrochemistry

The oxidation peak potentials (E_p) of alinine derivates and catechol in 0.1 mol/L KCl+15% alcohol solution were measured by cyclic voltammograms technique. The electrochemical oxidation condition was set according to the E_p. Three derivates of 4,5-disubstituted -1,2-benzoquinones were prepared via electrochemical oxidation-Michael addition reaction. The possible mechanism of electrochemical oxidation-Michael addition reaction is presented.

Study On Preparation Of Coarse And Fine γ-Lialo2 Mixed Powder Used For Mcfc Matrix, Hua-Xin Lin, Bao-Lian Yi, Lian-Ying Kong, En-Jun Zhang, Li Zhou, Feng-Xia Wang

Journal of Electrochemistry

Coarse α-LiALO₂ powder was transferred completely to γ-LiAlO₂ at 900 ℃ for ten hours. Fine γ-LiALO₂ powder was prepared by “chloride” synthesis. MCFC matrix was fabricated by mixing the coarse and fine γ-LiALO₂ powder and by tape cast. The out'put voltage of the cell assembled with the matrix was 0.85 and 0.75 V respectively at 200 and 300 mA/cm ², and power density was about 250 mW/cm². The performance of the matrix fabricated with the mixed powder was obviously more advanced than that of the matrix fabricated with only coarse γ-LiALO₂ powder.

Electrochemical Characterization Of Ir-Ta-Ti Metal Oxide Coated Titanium Anodes, Ting-Yong Wang, Li-Kun Xu, Guang-Zhang Chen

Journal of Electrochemistry

Ir-Ta-Ti metal oxide coated titanium anodes of variable composition were prepared by thermal decomposition. Their micro morphorogies and electrochemical properties were characterized by scanning electron microscope, open circuit potential, cyclic voltammetry, consumption rate measurements and accelerated life test. The SEM results indicated that all coatings were of a porous and cracked-mud microstructure influenced greatly by the composition of coatings. The electrochemical measurements showed that the Ir-Ta-Ti ternary oxide-coated anodes exhibited excellent electrochemical activity and electrochemical stability in both acidic media and seawater which were affected by the composition and microstructure of the coatings. Owing to good corrosion resistance and low …

Fabrication And Examination Of Reduced Temperatrue Solid Oxide Fuel Cell Using A Supported Thin Ysz Electrolyte Substrate, Yi-Huang Zhang, Yong-Lei Dong, Yi Jiang, Zhi-Gui Lu, Jing-Wang Yan

Journal of Electrochemistry

By using a cost-effective wet process,dense yttria stabilized zirconia (YSZ) films on Ni-YSZ anode substrates have been prepared successfully. The YSZ film was characterized to be around 10 μm in thickness, sufficiently dense, uniform and crack free. A single solid oxide fuel cell fabricated from the supported YSZ film electrolyte on the anode substrate and a LSM cathode prepared on the YSZ film was tested. The power density reached to 0.1 W/cm² at 800 ℃, showing a reasonable performance. Further analysis on both electrodes shows that the anodic overpotential was much larger than IR drop (including YSZ resistance and …

An Eis Study On The Synergetic Filming Between Cathodic Protection And The Corrosion Inhibitor, Yong-Tao Zhao, Jian-Hua Wu, Jian-Hua Qian, Hui Yu

Journal of Electrochemistry

The electrochemical impedance spectroscope (EIS) of 907A steel in seawater was investigated to study the film formation and destruction. The corrosion protection mechanism of the synergy interaction between cathodic protection and YKI-5 corrosion inhibitor (a mixture of polyhydric alcohol phosphate ester, phosphate and polyphosphate) is discused. Typical EIS spectral changes were clearly observed during the film formation and destruction processes. EIS results indicated that the film seemed to formed a multi-layered structure which consist of an inner layer (this may be an inhibitor-metal complex layer) and many outer layers of calcareous deposits. The film possesses of good persistency under the …

Electro-Oxidation Of Glyoxal To Glyoxalic Acid, Yin-Sheng Chen, Xin-Sheng Zhang, Jun Hu, Ying-Chun Dai

Journal of Electrochemistry

An investigation has been made to obtain the glyoxalic acid by the electrochemical oxidation of glyoxal solution with hydrochloric acid under various experimental conditions.The cell used consists of a lead cathode, a DSA anode and a cation-exchange membrane of model CM001. The current efficiency and yield for glyoxalic acid generation were 80.0% and 91.1% respectively, under optimal operating conditions: velocity of electrolyte flow 1.4 m·s^-1 ,current density 450 A·m^-2, temperature 30～40 ℃, initial concentration of glyoxal and hydrochloric acid 9.1%～16.0%, 4%～6%, respectively.

Studies Of The Preparation Of Electrodes From Lead Carbonate For Lead-Acid Battery Ⅱ. The Preparation Of Paste Electrodes, Zhong-Xu Dai, Di-Hua Wang, Hao-Hao Ke, Jin-Yun Zou, Yun-Hong Zhou

Journal of Electrochemistry

The positive and negative pastes were prepared by mixing PbCO₃ and H₂SO₄ solution as well as relative additives, respectively. The effects of the various formation methods and the charge/discharge conditions on discharge capacity and active material utilization of both electrodes were examined. The results indicate that the performance of the positive electrode formed at 2.0 mA/cm² is better than that formed at higher current density under the same charge/discharge condition, the PAM utilization reaches 74.4 % under discharging at 2.0 mA/cm²; and the property of the negative electrode formed by unsymmetrical square wave …

Application Of Wavelets And Principal Component Analysis In Image Query And Mammography, Sol Neeman Ph.D.

Engineering Studies Faculty Publications and Creative Works

Breast cancer is currently one of the major causes of death for women in the U.S. Mammography is currently the most effective method for detection of breast cancer and early detection has proven to be an efficient tool to reduce the number of deaths. Mammography is the most demanding of all clinical imaging applications as it requires high contrast, high signal to noise ratio and resolution with minimal x-radiation. According to studies [36], 10% to 30% of women having breast cancer and undergoing mammography, have negative mammograms, i.e. are misdiagnosed. Furthermore, only 20%-40% of the women who undergo biopsy, have …

Modeling The Effect Of Plasticizer On The Viscoelastic Response Of Crosslinked Polymers Using The Tube-Junction Model, P. P. Simon, Harry J. Ploehn

Faculty Publications

Plasticizers modify the mechanical properties of polymericmaterials. The effects of plasticizers on glass transition temperatures can be most clearly observed in isochronal temperature sweep profiles of viscoelastic dynamic moduli. However, no simple mathematical models of plasticization are available to those who wish to design and employ plasticized materials in specific applications. We extend a phenomenological, molecular-level model (known as the tube–junction model) for crosslinked polymers to describe the effect of plasticizers on dynamic moduli. We show that the increase in free volume fraction due to the presence of the plasticizer can account for the shift in the glass transition in …

Evaluation Of Moisture Barriers For Fire Fighting Turnout Gear Assessment Of Product Failure And Test Method Development Predicting Failure Modes, Chastity Danielle Newsome

Theses and Dissertations--Retailing and Tourism Management

The purpose of this study was to investigate the failures seen in the moisture barrier of fire fighting turnout gear. Moisture barriers taken from garments in field were evaluated to establish a baseline for comparison. Moisture barriers were exposed as part of a three-piece ensemble and as a single layer moisture barrier to instrumental light exposure in a Carbon Arc Fade-ometer and natural sunlight exposure according to AATCC and ASTM test methods. After exposure, moisture barriers were visually examined using stereo and compound microscopes. A performance measurement was conducted on the exposed moisture barriers using a modified NFPA Hydrostatic Water …

Matrix Structural Analysis, 2nd Edition, William Mcguire, Richard H. Gallagher, Ronald D. Ziemian

Faculty Books

The aims of the first edition of Matrix Structural Analysis were to place proper emphasis on the methods of matrix structural analysis used in practice and to lay the groundwork for more advanced subject matter. This extensively revised Second Edition accounts for changes in practice that have taken place in the intervening twenty years. It incorporates advances in the science and art of analysis that are suitable for application now, and will be of increasing importance in the years ahead. It is written to meet the needs of both the present and the coming generation of structural engineers.

KEY FEATURES …

Textured Mos 2 Thin Films Obtained On Tungsten: Electrical Properties Of The W/Mos 2 Contact, E. Gourmelon, J. C. Bernède, J. Pouzet, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Textured films of molybdenum disulfide have been obtained by solid state reaction between the constituents in thin films form when a (200) oriented tungsten sheet is used as substrate. The crystallites have their c axis perpendicular to the plane of the substrate. The annealing conditions are T=1073K and t=30 min. The films are stoichoimetric and p type. Such highly textured films are achieved without foreign atom addition (Ni, Co...). It appears, as shown by x-ray photoelectron spectroscopy, that a thin WS₂ layer is present at the interface W/MoS₂. The crystallization process is discussed by a …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

The Electrochemical Behaviors Of Superoxide Dismutase At Promoter Modified Gold Electrode, Xia-Qin Wu, Xiao-Yun Meng, Zhe-Su Wang, Zong-Rang Zhang

Journal of Electrochemistry

The electron-transfer process of superoxide dismutase was investigated by cyclic voltammetry at the 4,4'-dithiodipyridine, L-cysteine, histidine and arginine modified gold wire electrodes repectively. The quasi-reversible behavior was observed at L-cysteine modified gold electrode. An irreversible electrochemical behavior has been observed at hisdinine modified gold wire electrode.

Electro-Oxidation Of Phenol On Sno2/Ti Electrodes Prepared By Thermal Oxidation, Qing-Song Zhang, Hui-Huang Wu

Journal of Electrochemistry

A SnO₂/Ti electrode prepared by thermal oxidation was used as the anode for galvanostatic electrolysis in acidic solution containing phenol, the time-dependances of phenol concentration, chemical oxygen demand in solution(COD) and instantaneous current efficiency were determined during electrolysis. The results show that with the SnO₂/Ti anode instead of Pt, the COD significantly decreases at the same charge passage, and average current efficiency of oxidation increases by three times. The mechanism for phenol oxidation at two electrodes was discussed.