Engineering Science and Materials Commons^™

Charge Induced Enhancement Of Adsorption For Hydrogen Storage Materials, Xiang Sun

Dissertations, Master's Theses and Master's Reports - Open

The rising concerns about environmental pollution and global warming have facilitated research interest in hydrogen energy as an alternative energy source. To apply hydrogen for transportations, several issues have to be solved, within which hydrogen storage is the most critical problem. Lots of materials and devices have been developed; however, none is able to meet the DOE storage target. The primary issue for hydrogen physisorption is a weak interaction between hydrogen and the surface of solid materials, resulting negligible adsorption at room temperature. To solve this issue, there is a need to increase the interaction between the hydrogen molecules and …

New Formic Acid Fuel Cell Orientations To Reduce The Cost Of Cell Components, John Calvin Holtkamp

Browse all Theses and Dissertations

Formic acid fuel cells show the potential of outperforming or replacing direct methanol fuel cells. A number of issues need to be overcome in order for fuel cells, specifically formic acid fuel cells, to be seriously considered for use in small electronic devices. One of the largest issues inhibiting the commercial success of fuel cells is the cost of the components. The catalyst and ion-conducting membrane, key components in a fuel cell, are both expensive. With the current amount of costly materials needed to construct a fuel cell, fuel cells will have limited success in becoming mainstream power sources in …

Interfacial Modification Of Microcellular Carbon: Influence Of Ceramic And Carbon Nanotube Coatings, Anil Kumar Karumuri

Browse all Theses and Dissertations

Microcellular carbon is an emerging ultra lightweight and efficient thermal management material, which also has great potential as a reinforcement material for selected composites. However, these porous materials exhibit relatively low mechanical properties, and are susceptible to degradation in oxidizing environment. The scope of this research is to investigate surface modification approaches that can address these issues. Two specific objectives were: (1) to develop ceramic coatings to improve the survivability of carbon foams in high temperature applications, and (2) to develop and test modifications that can improve cellular composites involving carbon foam. It was seen that a mixed layer of …

Convergence, Adaptive Refinement, And Scaling In 1d Peridynamics, Florin Bobaru Ph.D., Mijia Yabg Ph.D., Leonardo F. Alves M.S., Stewart A. Silling Ph.D., Ebrahim Askari Ph.D., Jifeng Xu Ph.D.

Department of Engineering Mechanics: Faculty Publications

We introduce here adaptive refinement algorithms for the non-local method peridynamics, which was proposed (in J. Mech. Phys. Solids 2000; 48:175–209) as a reformulation of classical elasticity for discontinuities and long-range forces. We use scaling of the micromodulus and horizon and discuss the particular features of adaptivity in peridynamics for which multiscale modeling and grid refinement are closely connected. We discuss three types of numerical convergence for peridynamics and obtain uniform convergence to the classical solutions of static and dynamic elasticity problems in 1D in the limit of the horizon going to zero. Continuous micromoduli lead to optimal rates of …

Comparison Of Fuzzy Clustering Methods And Their Applications To Geophysics Data, David J. Miller, Carl A. Nelson, Molly Boeka Cannon, Kenneth P. Cannon

Department of Mechanical and Materials Engineering: Faculty Publications

Fuzzy clustering algorithms are helpful when there exists a dataset with subgroupings of points having indistinct boundaries and overlap between the clusters. Traditional methods have been extensively studied and used on real-world data, but require users to have some knowledge of the outcome a priori in order to determine howmany clusters to look for. Additionally, iterative algorithms choose the optimal number of clusters based on one of several performance measures. In this study, the authors compare the performance of three algorithms (fuzzy c-means, Gustafson-Kessel, and an iterative version of Gustafson-Kessel) when clustering a traditional data set as well as real-world …

Experimental Investigation Of A Novel Blast Wave Mitigation Device, Zhenbi Su, Wen Peng, Zhaoyan Zhang, George Gogos, Reed Skaggs, Bryan Cheeseman, Chian Fong Yen

Department of Mechanical and Materials Engineering: Faculty Publications

A novel blast wave mitigation device was investigated experimentally in this paper. The device consists of a pistoncylinder assembly. A shock wave is induced within the cylinder when a blast wave impacts on the piston. The shock wave propagates inside the device and is reflected repeatedly. The shock wave propagation process inside the device lengthens the duration of the force on the base of the device to several orders of magnitude of the duration of the blast wave, while it decreases the maximum pressure over an order of magnitude. Two types of experiments were carried out to study the blast …

Me-Em 2009 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Energy Systems
• Health Systems
• Faculty & Staff
• Students
• Alumni
• Resources
• Graduates
• Publications
• ME-EM Community

Helical Force Flow: A New Engineering Mechanics Model For Biological Materials, Jeffery S. Thomas

Doctoral Dissertations

"The author has long speculated that the prevalence of helical structures in botany and zoology hints to an optimized pathway for force and/or energy transfer. His goal has been to realize an alternative approach to the standard stress analysis used in engineering in order to more efficiently and accurately deal with biological materials. Improved tools for these natural materials should in turn aid the design and analysis of engineered materials. Following the role of a navigator in leaf C. Levesque's book "Breakthrough Creativity", the author typically searches for ideas in a variety of places, including physics, materials science, biomimetics, dimensional …

Electronic And Structural Properties Of Molybdenum Thin Films As Determined By Real Time Spectroscopic Ellipsometry, J. D. Walker, H. Khatri, V. Ranjan, Jian Li, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Walker, J.D., Khatri, H., Ranjan, V., Li, J., Collins, R.W., & Marsillac, S. (2009). Electronic and structural properties of molybdenum thin films as determined by real-time spectroscopic ellipsometry. Applied Physics Letters, 94(14). doi: 10.1063/1.3117222

Failure Analysis And Materials Characterization Of Hip Implants, Amanda Marie Bastidos

Open Access Theses & Dissertations

This research focused on the microstructural characterization and failure analysis of hip implant components. The main hip components analyzed were the femoral heads and the ultra-high molecular weight polyethylene (UHMWPE) liners. Previous research has shown that hip implants tend to fail by the PE liners due to adhesive and abrasive wear, delamination, and third body particles (metals, ceramics, and PE). The methods and procedures for analyzing the said failures consisted of non-destructive and destructive evaluations. Non-destructive evaluations included of techniques such as visual characterization and dye penetrant inspection (DPI)-which displayed macroscopic surface details and presented initial clues as to the …

Art In A New Light: Design And Assessment Of Illuminants To Reduce Photochemical Degradation Of Works Of Art, Monica Fabiola Delgado

Open Access Theses & Dissertations

The purpose of this research is to design the best lighting that will minimize long term photochemical degradation of Old Master Drawings and/or other works of art, while maintaining the patron's appreciation of the object's color and detail. The present approach is a technological refinement to the basic underlying earlier work on fluorescent lighting by W. A. Thornton, W.A. at General Electric1. Thin-film dielectric, multi-coating technology is used to create filters that eliminate ultraviolet light, near infrared light and significant unnecessary parts from the visible spectrum, thus maximizing the reduction in photochemical degradation, while maintaining optimal color rendering. Three interference …

Additive Layer Manufacturing Of Ti-6al-4v By Electron Beam Melting From Powder Particles: Solid, Mesh And Foam Components Study, Sara M. Gaytan

Open Access Theses & Dissertations

Additive Manufacturing by Electron Beam Melting Rapid Manufacturing is a technology that consists of the fabrication of a CAD design by melting powder particles in a layer by layer fashion. In this study, Ti-6Al-4V has been utilized to fabricate solid, mesh and foam components by EBM technologies. Powder analysis of Ti-6Al-4V was performed to obtain a better understanding of the porosity obtained by the system. After proper optimization of the machine, and porosity control, microstructural analysis was performed to the components already mentioned and correlated by transmission electron microscopy. Besides the microstructural analysis, tensile and hardness testing was performed to …

Assessing Repeatability Of Four-Point Bending Method For Estimating Fatigue Cracking Of Hot Mix Asphalt, Sara -. Montazeri

Open Access Theses & Dissertations

The objective of this thesis was to assess the repeatability of four-point bending method for estimating fatigue cracking of hot mix asphalt. This experimental research examined the influence of mix proportions, specifically asphalt and air void contents, on fatigue behavior of asphalt beam specimens in the laboratory tested with four-point bending method of loading. Following the relevant specifications, the strain-controlled mode of loading was selected. Fatigue failure is expected to occur at the cycle which the flexural stiffness of asphalt specimen reduced to 50% of initial amount. Up to a 1,000,000 cycles of loading were applied to each specimen.

Different …

High Temperature Oxidation Characteristics Of Nb-10w-Xcr Alloys, Maria Del Pilar Moricca

Open Access Theses & Dissertations

The use of refractory metals in high temperature applications has been attractive for several years. Systems based on niobium represent a potential new generation of refractory materials systems because of their low density, high melting points, and strength at elevated temperatures. Despite these desirable characteristics, the widespread use of niobium-based alloys is limited because its oxidation resistance is still inadequate for structural applications. Understanding the oxidation kinetics of Nb-based alloys and the role of the different phases in the oxidation process is of crucial importance to improve the oxidation resistance of these materials.

The effect of Cr content on the …

Microstructural Characterization Of Overaged Gtd-111 Hp Turbine Buckets, Oscar Quintero

Open Access Theses & Dissertations

Superalloys are metallic materials that exhibit excellent mechanical strength and creep resistance at high temperatures. They have good surface stability and are corrosion resistant. Superalloys are mostly used in the aerospace industry, gas turbine engines and blades (hot zones of gas turbines), and where extreme heat is encountered. The focus of this research was on the GTD-111 Ni-base superalloy, which is a General Electric (GE) proprietary superalloy mostly used in gas turbine blades with the form of high pressure or first stage buckets. This alloys features better mechanical properties, creep resistance, and a higher stress rupture temperature than the commonly …

Impacting Testing Of High Temperature Ceramics Through The Use Of A Vitiated Heater For Hot And Cold Fire Collisions, Adrian Trejo

Open Access Theses & Dissertations

Material testing is a crucial step during the design process as particular materials serve as safety and life saving conditions. In this study, a MoSi2 is chosen as the target specimen to undergo impact under high temperatures. An impact apparatus is designed and constructed for the purpose of propelling alumina particles at high velocities. A nozzle using compressed nitrogen gas is used to fire the particle at the desired velocities. Due to the possibility of thermal shock occurring at higher temperatures, a separate nozzle utilizing vitiation heating is designed to fire the particle at equally higher temperatures to prove the …

Observed Superspin-Glass Behavior In Ni0.5zn0.5fe2o4 Nanoparticles, Antony Adair

Open Access Theses & Dissertations

In this investigation we seek to identify the magnetic behavior of Ni0.5Zn0.5Fe2O4 nanoparticles though AC-susceptibility and DC-magnetization measurements. Powder x-ray diffraction was performed to determine the purity and average diameter ( ~ 9nm) of the particles. Aditionally, structure was confirmed by comparison through the International Centre for Diffraction Data's Powder Diffraction File [52] (PDF # 08-0234).

Zero-field cooled and field cooled DC magnetization measurements (bifurcation and blocking temperature), as well as M(H) hysteresis (below and above the blocking temperature) lead us to initially suggest that the material may in fact be superparamagnetic. However, further investigation of the real AC susceptibility …

Temperature-Induced Phenomena In Systems Of Magnetic Nanoparticles, Abdul Wazed Bhuiya

Open Access Theses & Dissertations

Magnetic nanoparticle ensembles have received a lot of attention, stemming in part from their current and potential applications in biomedicine and in the development of high-density magnetic storage media. Key to the functionality of these systems are microscopic structures and mechanisms that make them exhibit unique properties and behave differently from their bulk counterparts.

We studied microscopic structures and processes that dictate macroscopic properties, behavior and functionality of magnetic nanoparticle ensembles. As the temperature T strongly influences the magnetic behavior of these systems, we studied temperature dependent magnetic properties using AC-susceptibility and DC-magnetization measurements carried out over a broad range …

Microstructural Characterization And Heat Treatment Of A-286 Turbine Buckets, Christopher Michael Bradley

Open Access Theses & Dissertations

A-286 is an iron-based superalloy used extensively in land-based gas turbines for 2nd stage (low pressure) buckets and 1st and 2nd stage wheels. Although A-286 may appear to some as just another austenitic stainless steel, its elevated temperature properties are attributed to ' precipitate structures, effective distributions of alloy carbides in the forms of M23C6, M6C and MC, and solid solution strengthening. Unfortunately over the course of these components service lives microstructural degradation develops in the form of η-phase formation. The presence of η-phase, especially in large quantities, can have a negative effect on stress rupture properties. Resistance to creep …

Spectroscopic Characterizations Of Organic/Inorganic Nanocomposites, Jayesh Rasikalal Govani

Open Access Theses & Dissertations

Inorganic potassium dihydrogen phosphate (KDP) is widely known for its value as a nonlinear optical material. In this study, pure and l-arginine-doped KDP single crystals were grown by the slow solvent evaporation technique and further subjected to infrared absorption and Raman studies for the confirmation of chemical group functionalization and possible bonding between the organic and inorganic materials. The appearance in the infrared absorption spectra of additional vibrational lines, which mostly originate from disturbed N-H, C-H, and C-N bonds of the l-arginine-doped salt, confirm the interaction between KDP and the organic material. This affirmation is supported by more evidence from …

Effects Of Build Orientation, Aging, And Pre-Conditioning On Mechanical Properties For Stereolithography-Manufactured Astm Type I Specimens Using A Design Of Experiments Approach, Karina Puebla

Open Access Theses & Dissertations

With industry's growing focus on the rapid manufacturing (RM) of end-use products, rapid prototyping (RP) or layered manufacturing (LM) machines that were originally designed to build prototypes may now be required to build functional end-use products. To successfully accomplish the transition, the available materials utilized in RP must provide the performance required for RM. The specific technology used must also be capable of producing repeatable and reproducible parts in regards to mechanical and dimensional properties.

A design of experiments approach was performed to determine the effects of build orientation, aging, and pre-conditioning on the mechanical properties. To perform the investigations, …

Computational Modeling Studies Of The Structures And Properties Of Organotin(Iv) And Stannyl-Thioether Systems With Comparisons To X-Ray Crystallography, Michelle R. Stem Joseph

Open Access Theses & Dissertations

Controlling the toxic effects of organotin(IV) compounds involves engineering the structure of the molecules to optimize their properties. Molecular engineering, coupled with improved capabilities to generate reliable computational optimization models (COMs), will enable researchers to have greater success at harnessing the highly specific cytotoxicity of organotins. For example, as the thio_n ligand phenyl groups were replaced with Cl atoms, the S-Sn intramolecularity was strengthened, the bond distance decreased, and the stannyl tetrahedral structure was deformed from its triphenyl conformation. With each substitution, conformation deformations lowered the damaging bioactivity levels of thio_n. Bonding various ligands to organotin(IV) compounds …

Experimental Study Of The Response Of Semiconductor Detectors For Edxrf Analysis., Sunil Kumar Valaparla

Open Access Theses & Dissertations

This present work relates to the study and characterization of the response function of an energy-dispersive x-ray spectrometer. The problems of energy, efficiency and resolution calibration of the system operating in the energy (5-60 keV) range are discussed. We present the operation characteristics of the portable pyro-electric x-ray generator (COOL-X) and the application of the calibrated response spectrum in the elemental analysis using X-ray Fluorescence (XRF).

We study the response of the Si(Li)-Pin XR-100CR semiconductor detector to low energy photons. The photopeak efficiency was determined experimentally by using radioisotopes and compared against a theoretical efficiency curve. The efficiency for gamma …

High Temperature Oxidation Behavior Of Nb-20mo-15si-5b-20cr Alloy, Julieta Angelica Ventura

Open Access Theses & Dissertations

Materials for high temperature applications, such as jet engines, gas turbines and turbine blades, require a balanced combination of physical and chemical properties to withstand the aggressive environments in which they are utilized. Some of the properties required are high strength, low density, high melting point and good oxidation resistance at elevated temperatures [1-3]. For this reason, the microstructure and oxidation behavior of the Nb-20Mo-15Si-5B-20Cr alloy (at.%) has been studied as a potential candidate to replace Nickel-based alloys currently used in the aerospace industry.

Short term oxidation (STO) and long term oxidation (LTO) studies have been performed in air for …

Exploring Poly(Ethylene Glycol) As A Suitable Material For Peripheral Nerve Regeneration Scaffolds Manufactured By Stereolithography, Nubia Zuverza

Open Access Theses & Dissertations

One of the challenges in tissue engineering is to have spatial and temporal control over the biological elements within a scaffold used to guide regeneration for example of transected nerves. Some of the physical and chemical characteristics to regulate include incorporation of bioactive domains and release of chemical signals. This study presents the use of stereolithography (SL) to incorporate localized domains for cell adhesion in addition to include releasable nerve growth factor (NGF) in the process of building poly(ethylene glycol)diacrylate (PEGda) hydrogel scaffolds. Besides providing sites for cell attachment, an ideal nerve guidance conduit (NGC) should be able to release …

Independent Torque Distribution Management Systems For Vehicle Stability Control, Indrasen Karogal

All Theses

Vehicle Dynamics Control (VDC) systems, also called Electronic Stability Control (ESC) systems, are active on-board safety systems intended to stabilize the dynamics of vehicle lateral motion. In so doing, these systems reduce the possibility of the driver's loss of control of the vehicle in some critical or aggressive maneuvers. One approach to vehicle dynamics control is the use of appropriate drive torque distribution to the wheels of the vehicle. This thesis focuses on particular torque distribution management systems suitable for vehicles with independently driven wheels.
In conducting this study, a non-linear seven degree-of-freedom vehicle model incorporating a non-linear tire model …

Modeling, Analysis And Control Of Flexible Solid-State Hysteretic Actuators, Kushan Vora

All Theses

A distributed parameters modeling and control framework for flexible solid-state hysteretic actuator is presented in this work. For the simplicity of analysis, the actuator dynamic behavior is decoupled and treated separately from the hysteresis nonlinearity. To include the effects of widely-used flexural mechanisms, a mass-spring-damper boundary condition is considered for system. Moreover, the effect of electromechanical actuation is included as a concentrate force at the boundary. The problem is then divided into two parts: first part deals with free motion analysis of system in order to obtain eigenvalues and eigenfunctions using the expansion theorem and a standard eigenvalue problem procedure. …

An Investigation On Spot-Weld Modeling Complexity For Crash Simulation, Srinivasan Vimalanathan

All Theses

In order to design car body structures which are safe during crash, modern automotive manufacturers perform both full-scale experimental crash tests and computer simulation of vehicle crash events using commercially available Finite Element Analysis (FEA) packages such as ABAQUS or LS-DYNA. Use of crash simulations significantly reduces the number of real time crash experiments needed and reduces the time required for design changes. However, in order to capture accurately crash behavior during high-speed impact, a large amount of detailed FEA modeling features such as number and types of elements, mesh element size, number of components, different types of connectors, material …

Computational Analysis Of Input-Shaping Control Of Microelectromechanical Mirrors, Thomas Starling

All Theses

Advances in micromachining technology have enabled the design and development of high performance microelectromechanical systems (MEMS). There is a pressing need for control techniques that can be used to improve the dynamic behavior of MEMS such as the response speed and precision. In MEMS applications, open-loop control is attractive as it computes a priori the required system input to achieve desired dynamic behavior without using feedback, thus eliminating the problems associated with closed-loop MEMS control. While the input-shaping control is attractive due to its simplicity, the effectiveness of this control approach depends on the accuracy of the model that is …

Nonlinear Finite Element Analysis Of Tweel Geometric Parameter Modifications On Spoke Dynamics During High Speed Rolling, Maya Ramachandran

All Theses

The acoustic signature and noise produced by non-pnuematic wheels such as the Michelin TWEELTM is a critical design criteria for automotive and other mobility applications. The TWEELTM structure consists of three basic parts: (1) a circular deformable 'shear beam', (2) collapsible spokes and (3) a rigid hub. During high speed rolling the TWEELTM produces acoustic noise which is hypothesized to be due to resonant vibration of the TWEELTM spokes as they enter the contact region, buckle and then snap back into a state of tension. In order to identify and help understand the causes of acoustic noise for a rolling …