Engineering Science and Materials Commons^™

Effect Of Fe2+/Fe3+Interconvertion On Reduction Behavior Of Fe3+ In Acidic Electrolytes, Jian-Xin Qin, Feng Lin, Wen-Ping Liu, Chao Chen, Meng-De Ren

Journal of Electrochemistry

The influences of ferrous/ferric (Fe²⁺/Fe³⁺) interconvertion on electrochemical reduction and electrode reaction of Fe³⁺ were investigated by using linear sweep voltammetry, potentiostatic method and cyclic voltammetry (CV) in acidic electrolytes containing chloride ion (Cl^-) and sulfate ion (SO₄^2-). It was shown that the reduction process of Fe³⁺/Fe²⁺ would take place in two independent stages: (1) the reduction of Fe³⁺ to Fe²⁺ at E=0.35V and (2) the co-precipitation of Fe²⁺ by forming Fe(OH)₂ (E≤-0.3 V) instead of Fe. The major effect of Fe^{2+ …}

Effect Of Calcium On Atmospheric Corrosion Resistance Of Bridge Steel, Dong-Liang Li, Gui-Qin Fu, Miao-Yong Zhu

Journal of Electrochemistry

The corrosion behavior of bridge steel in simulated hot and humid industrial-marine atmosphere was investigated by mass loss analysis, XRD, SEM, electrochemical methods and a wet/dry alternate immersion corrosion test using 0.1 mol•L^-1 NaCl+0.01 mol•L^-1 NaHSO₃ solutions. The corrosion depth (W) of experimental steels before and after calcium treatment versus time (t) curves showed a good agreement with the power function of W=Atⁿ. The corrosion products were mainly composed of amorphous phase and a small amount of crystals including α-FeOOH, β-FeOOH, γ-FeOOH and Fe₃O₄. Trace calcium could promote the formation of …

Characterization Of Structural Dynamics Of The Human Head Using Magnetic Resonance Elastography, Andrew Arun Badachhape

McKelvey School of Engineering Graduate Student Theses & Dissertations

In traumatic brain injury (TBI), the skull-brain interface, composed of three meningeal layers: the dura mater, arachnoid mater, and pia mater, along with cerebrospinal fluid (CSF) between the layers, plays a vital role in transmitting motion from the skull to brain tissue. Magnetic resonance elastography (MRE) is a noninvasive imaging modality capable of providing in vivo estimates of tissue motion and material properties. The objective of this work is to augment human and phantom MRE studies to better characterize the mechanical contributions of the skull-brain interface to improve the parameterization and validation of computational models of TBI. Three specific aims …

Characterization And Modeling Of Asphalt Concrete For Dynamic Properties And Performances, A S M A. Rahman

Civil Engineering ETDs

The recently developed mechanistic-empirical pavement design guide (MEPDG, also known as Pavement M-E design method) uses the nationally calibrated, binder viscosity-based dynamic modulus predictive model for the design and analysis of asphalt pavements. In this study, this model is assessed for its appropriateness for asphalt-aggregate mixtures typically used in New Mexico. In essence, this study investigates the predictability issue of complex modulus of New Mexico mixes. A total of 54 Superpave mixes with different aggregate gradations, air voids, and binder grades were collected from the mixing plants and from the pavement construction sites. The loose asphalt mixtures were then compacted, …

The Inter-Laminar Shearing Effect On Wrinkle Development In Composite Forming Processes, David Sundquist

McKelvey School of Engineering Graduate Student Theses & Dissertations

Composite materials are becoming prevalent in aerospace industries as the uniqueness of the composite structure allows the composite to be tailored specifically for individual applications. Many fabrication techniques produce defects in composite parts such as wrinkles, fiber waviness, fiber misalignment, and porosity. The driving mechanisms behind these defects occurring during forming processes are not fully understood and, thus, characterization formation of these defects in a uncured state is beneficial to optimize composite processing. This work primarily investigated the influence of how uncured pre-impregnated carbon ply properties affect the wrinkling behavior of a composite laminates. Several factors affecting composite ply forming …

Functional Bio-Nano Hybrids Through A Precise Control Of Interfacial Interactions At The Nanoscale, Sirimuvva Tadepalli

McKelvey School of Engineering Graduate Student Theses & Dissertations

During the course of evolution, proteins have evolved to perform exquisite functions including structural support, signal transduction, actuation, sensing, catalysis, trafficking, gating, light-harvesting, charge transfer, molecular recognition, self-assembly, self-organization, or combinations of two or more of these functions. A precise control and manipulation of the structure and function of proteins is conceivable with the advent of nanotechnology, which has facilitated the integration of nanomaterials with functional biomolecules to realize bio-nano hybrids with synergistically enhanced functionalities.

At the genesis of bionanotechnology, a paucity in the fundamental understanding of the bio-nano interfaces is a grave impediment to the progress of the field. …

Wireless Power Transfer Roadway Integration, Trevor Gardner

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Electric vehicles represent a major accomplishment in the energy and transportation industry. Unfortunately, they are restricted to a small travel range because of limited battery life. Successful integration of wireless power transfer (WPT) systems into the infrastructure would remove the range restrictions of EVs. To successfully integrate this technology, several requirements must be met. First, the embedment process cannot interfere with the electrical performance of the inductive power transfer (IPT) system. Second, the presence of the IPT system in the pavement structure cannot negatively affect the roadway’s lifespan.

Several systems were directly embedded in roadway materials. The electrical properties of …

Optical Flow Method For Blood Flow Velocimetry Based On Digital X-Ray Subtraction Angiography: A Brief Review, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

Detailed blood flow information has been recognized as the key information for diagnosis of vascular diseases, such as vascular stenosis and aneurysms. Optical flow method (OFM) is an emergent technique as a tool to analyze the digital x-ray subtraction angiographic images of blood vessels to obtain the detailed blood flow distribution in vascular systems. A brief review isconstructed to discuss the status, applicability, accuracy and future direction of the optical flow technique in the physical study of vascular flow.

Controlled Electrochemical Reduction Of Gold And Palladium Metal Precursors In Polyaniline, Nicole Goodwin

UNLV Theses, Dissertations, Professional Papers, and Capstones

Polyaniline (PANI) has been extensively studied due to its unique electrochemical properties. The conjugated polymer is conductive with high chemical stability below 100°C, mechanical strength, and large surface area. The applications of PANI have included chemical sensing, corrosion inhibition coatings, light emitting diode and as a substrate for metal composite catalysts. Both chemical and electrochemical methods have been developed and utilized in the synthesis of PANI/metal composites. The simultaneous reduction of aniline and metal precursor produces a composite of PANI encapsulated metal, reducing the active surface area available for catalysis. Alternatively, chemical reduction of the metal precursor into preformed PANI …

Surface And Interface Characterization Of Solution-Processed Metal Oxides And Pedot:Pss Using Photoelectron Spectroscopy, Lynette M. Kogler

UNLV Theses, Dissertations, Professional Papers, and Capstones

Solution-processed materials are appealing for use in printable electronics as a means to lower production costs, but precise control of the process is crucial for achieving the desired properties in the final materials and their interfaces. Electronic interface properties depend on both the involved materials and their fabrication processes, impacting the development and commercialization of these materials. Analyzing the chemical and electronic structure of these materials, particularly at the surfaces and interfaces, is important not only for insuring that the materials have the desired properties, but also for understanding the effects of the fabrication process and how to modify properties …

Synthesis Of Magnetic Carbon Supported Manganese Catalysts For Phenol Oxidation By Activation Of Peroxymonosulfate, Yuxian Wang, Yongbing Xie, Chunmao Chen, Xiaoguang Duan, Hongqi Sun, Shaobin Wang

Research outputs 2014 to 2021

Magnetic core/shell nanospheres (MCS) were synthesized by a novel and facile one-step hydrothermal method. Supported manganese oxide nanoparticles (Fe₃O₄/C/Mn) were obtained from various methods (including redox, hydrothermal and impregnation) using MCS as the support material and potassium permanganate as the precursor of manganese oxide. The Mn/MCS catalysts were characterized by a variety of characterization techniques and the catalytic performances of Fe₃O₄/C/Mn nanoparticles were tested in activation of peroxymonosulfate to produce reactive radicals for phenol degradation in aqueous solutions. It was found that Fe₃O₄/C/Mn catalysts can be well dispersed …

The Role Of Soil Stiffness In Reverse Fault Rupture Propagation, Moises I. Buelna

Master's Theses

A nonlinear Mohr-Coulomb constitutive model with a strain dependent yield surface and non-associated flow was employed to study the plastic soil properties which affect the rate of surface fault rupture propagation in reverse events. These numerical simulations show a trend for soils with higher stiffness to have a higher rate of rupture propagation. Additionally the study shows the effects of strain softening and hardening on the rate of rupture propagation. Soils which strain harden exhibiting ductile behavior typically require more basal offset to rupture to the surface than soils which strain soften exhibiting brittle behavior. These results agree with our …

Me-Em Enewsbrief, July-December 2017, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

A Comparison Study Of Composite Laminated Plates With Holes Under Tension, Joun S. Kim

Master's Theses

A Comparison Study of Composite Laminated Plates with Holes under Tension

A study was conducted to quantify the accuracy of numerical approximations to deem sufficiency in validating structural composite design, thus minimizing, or even eliminating the need for experimental test. Error values for stress and strain were compared between Finite Element Analysis (FEA) and analytical (Classical Laminated Plate Theory), and FEA and experimental tensile test for two composite plate designs under tension: a cross-ply composite plate design of [(0/90)4]s, and a quasi-isotropic layup design of [02/+45/-45/902]s, each with a single, centered hole of 1/8” diameter, and 1/4" diameter (four sets …

Blanking Clearance And Punch Velocity Effects On The Sheared Edge Characteristic In Micro-Blanking Of Commercially Pure Copper Sheet, Didin Zakariya Lubis, Ichsan Ristiawan

Journal of Mechanical Engineering Science and Technology (JMEST)

This study aims to identify the influences between clearance and punch velocity on the part edge quality of blanked parts. Experiments have been conducted using material copper, punch-die clearance and punch velocity variations. In order to determine the reachable punch-die clearance and punch velocity required for blanking. The quality of the part-edge characteristics shows that higher punch velocity and decreases clearance value can improve the part-edge quality, resulting in smaller burr height and rollover, and a larger shear zone. Furthermore, it could be observed that the part-edge quality improvement when blanking with high punch velocity is much more distinct for …

Formula Of Moulding Sand, Bentonite And Portland Cement To Improve The Quality Of Al-Si Cast Alloy, Andoko Andoko, Poppy Puspitasari, Avita Ayu Permanasari, Didin Zakaria Lubis

Journal of Mechanical Engineering Science and Technology (JMEST)

A binder is any material used to strengthen the bonding of moulding sand grains. The primary function of the binder is to hold the moulding sand and other materialstogether to produce high-quality casts. In this study, there were four binder compositions being tested, i.e. 5% bentonite + 5% Portland cement, 4% bentonite + 6% Portland cement, 6% bentonite + 4% Portland cement, and 7% bentonite + 3% Portland cement. Each specimen was measured for its compressive strength, shear strength, tensile strength and permeability. The highest compressive strength was obtained fromthe specimen composed of 6% bentonite+ 4% Portland cement. The highest …

Modeling Of Antenna For Deep Target Hydrocarbon Exploration, Nadeem Nasir, Noorhana Yahya, Hasnah Mohd Zaid, Afza Shafie, Norhisham Hamid

Journal of Mechanical Engineering Science and Technology (JMEST)

Nowadays control source electromagnetic method is used for offshore hydrocarbon exploration. Hydrocarbon detection in sea bed logging (SBL) is a very challenging task for deep target hydrocarbon reservoir. Response of electromagnetic (EM) field from marine environment is very low and it is very difficult to predict deep target reservoir below 2km from the sea floor. This work premise deals with modeling of new antenna for deep water deep target hydrocarbon exploration. Conventional and new EM antennas at 0.125Hz frequency are used in modeling for the detection of deep target hydrocarbon reservoir. The proposed area of the seabed model (40km ´ …

Properties Of Brass Under Different Pouring Temperatures In Sand Casting Process, Poppy Puspitasari, Avita Ayu Permanasari, Andoko Andoko, Bayu Angga Pratama

Journal of Mechanical Engineering Science and Technology (JMEST)

This study aimed to determine the toughness of casts produced by the sand casting process at various temperatures against brass, and to investigate the structure contained in the cast madeusing abrass metal mould. This study was experimental research that observed the results of a treatment applied to a specimen group. This pre-experimental study usedthe one-shot case study model in which a group of samples was given treatment. The results showed that the specimen poured at 900°C exhibiteda microstructure consisting ofgood Cu-Zn content, while that at 700°Chad the least Cu content. It indicates that the higher the temperature used for metal …

Development Of A Ferrite-Based Electromagnetic Wave Detector, Muhammad Hanis Bin Zakariah, Poppy Puspitasari, Nur Azliza Ahmad

Journal of Mechanical Engineering Science and Technology (JMEST)

Direct detection of hydrocarbon by an active source using electromagnetic (EM) wave termed Sea Bed Logging (SBL) has shown very promising results. However, currently available electromagnetic wave technology has a number of challenges including sensitivity and lapsed time. Our initial response to this issue is to develop a ferrite-based EM wave detector for Sea Bed Logging (SBL). Ferrite bar and copper rings in various diameters were used as detector 1 (D1). For Detector 2 (D2), toroid added with copper wires in different lengths at the centre of it were used. The first experiment is to determine the inductance and resistance …

Thermogravimetric And Kinetic Analysis Of Cassava Starch Based Bioplastic, Nanang Eko Wahyuningtiyas, Heru Suryanto, Eddy Rudiyanto, Sukarni Sukarni, Poppy Puspitasari

Journal of Mechanical Engineering Science and Technology (JMEST)

Cassava starch based bioplasticfor packaging application has great potency because of the various starchproducing plants in Indonesia.Bioplasticcan contribute to reduce the dependence on fossil fuels andpetroleumthat can solve the environmentalproblem.Thepurpose of this research is to find out the thermal decomposition and the activation energy of cassava starch based bioplastic. The methods weresynthesis bioplastic with cassava starch as main component and glycerol as plasticizer. The thermogravimetry analysis was conducted to obtain the decomposition process mechanism of bioplastic and the heating valueof bioplasticwas measured using theadiabatic bomb calorimetric. Data analysis was conducted using a fitting model approach with an acikalin method to …

Compositional And Structural Evolution During Ball Milling Of Ti-Based Metallic Glass Powder, Yanuar Rohmat Aji Pradana

Journal of Mechanical Engineering Science and Technology (JMEST)

Ti42Zr40Ta3Si7.5Sn7.5metallic glass powder prepared for subsequent consolidation by hot pressing were produced by high energy ball milling from amorphous ribbon and both of the compositional and structural evolution on milled powders were studied using XRD and DSC analyses. By using WC vial and balls, the abrasion of milling media occurred causing WC contamination on < 105 µm milled powder after 2 cycles of milling. Based on DSC analysis, the contamination clearly reduced theΔTxof the alloy up to 48%. On the other hand, the contamination were overcome after milling using SS vial and balls, proved by no crystal peak observed on XRD pattern of all milling cycle levels. However, the thermal stability was noticed to be decreased implying the presence of nanocrystals on the amorphous powder after ball milling and the nanocrystal amount tend to be higher when more milling cycles were applied.

Synthesis Of Graphene And Graphene-Based Composite Membrane, Yuanjun Fan

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Vibration membrane equipped for earphone requires high performance in both mechanical properties and electronic properties. With extraordinary properties on both, graphene and graphene-based composite materials appear as a promising candidate for this application. Chemical vapor deposition (CVD) is believed to be the most convenient way to synthesize a large area (on scale of square centimeters) as well as a homogeneous thickness for the membrane. The thesis focuses on applying control variable experiment method to analyze different effects on mechanical property of the two CVD setting parameters: cooling rate, and hydrocarbon precursor. For isolating the specimens efficiently, a modified electrochemical method …

Method For Single Crystal Growth Of Photovoltaic Perovskite Material And Devices, Jinsong Huang, Qingfeng Dong

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for perovskite single crystal growth include using a low temperature solution process that employs a temperature gradient in a perovskite solution in a container , also including at least one small perovskite single crystal , and a substrate in the solution upon which substrate a perovskite crystal nucleates and grows , in part due to the temperature gradient in the solution and in part due to a temperature gradient in the substrate . For example , a top portion of the substrate external to the solution may be cooled .

Oct-Based Three Dimensional Modeling Of Stent Deployment, Pengfei Dong, David Prabhu, David L. Wilson, Hiram G. Bezerra, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Stent deployment has been widely used to treat narrowed coronary artery. Its acute outcome in terms of stent under expansion and malapposition depends on the extent and shape of calcifications. However, no clear understanding as to how to quantify or categorize the impact of calcification. We have conducted ex vivo stenting characterized by the optical coherence tomography (OCT). The goal of this work is to capture the ex vivo stent deployment and quantify the effect of calcium morphology on the stenting. A three dimensional model of calcified plaque was reconstructed from ex vivo OCT images. The crimping, balloon expansion and …

Special Issue On Supercapacitors, Xiao-Gang Zhang

Journal of Electrochemistry

/

Strategies To Enhance Energy Density For Supercapacitors, Jun-Wei Lang, Xu Zhang, Ru-Tao Wang, Xing-Bin Yan

Journal of Electrochemistry

The biggest advantage of supercapacitor lies in not only the excellent pulse and fast charging-discharging performance, but also the characteristics of long cycle life and wide operating temperature window with no pollution. However, the energy density of supercapacitor is low. In this paper, the working principle, the development status, defects and improvement method of supercapacitors are introduced. Based on the research workes of the supercapacitors with high energy density in our group, combined with the literature reports in recent years, the strategies to promote the energy density of supercarpacitors will be focused. The strategies for the enhancement of energy density …

Porous Carbon Materials Produced By Koh Activation For Supercapacitor Electrodes, Jiang-Lin Ye, Yan-Wu Zhu

Journal of Electrochemistry

Porous carbon materials with high specific surface area and excellent conductivity have wide applications in supercapacitor electrodes. Much effort has been made to synthesize and tailor the microstructures of porous carbon materials via various activation procedures (physical and chemical activations). In particular, the chemical activation using potassium hydroxide (KOH) as an activating reagent is promising because of the well-defined micropore size distribution and ultrahigh specific surface area up to 3000 m²·g^-1 of the resulting porous carbons. Based mainly on the previous works taken by the authors and collaborators in the field, we have summarized the activation mechanism …

Recent Advances On Carbon And Transition Metallic Compound Electrodes For High-Performance Supercapacitors, Dun Lin, Xi-Yue Zhang, Yin-Xiang Zeng, Ming-Hao Yu, Xi-Hong Lu, Ye-Xiang Tong

Journal of Electrochemistry

Supercapacitors (SCs) have stimulated intensive interests for their promising applications in electric vehicles and portable electronics, etc. Electrode material is the most important key component of SCs, which vastly determines the performance of SCs. Carbon and transition metallic compound materials have attracted considerable attention and been widely explored as electrode materials. However, the insufficient capacitance of carbon materials and unsatisfactory conductivity and cyclic stability of transition metallic compounds severely limit their implementation as robust SC electrodes. Herein, we highlight our recent efforts to boost the capacitive performance of carbon and metal oxide/nitride electrodes by rationally structural and componential design. The …

Lithium Ion Hybrid Capacitor With High Energy Density, Xian-Zhong Sun, Xiong Zhang, Kai Wang, Yan-Wei Ma

Journal of Electrochemistry

Lithium ion hybrid capacitors are electrochemical energy storage devices combining the advantages of both Li-ion battery and electrochemical capacitor. They can be extensively used in many fields. However, the commercialization of lithium ion hybrid capacitor has been encountered several problems, e.g., the device structure design, the screening of materials, the pre-lithiation process, and the interface between electrolyte and electrode, etc. This review summarizes the recent research advances in lithium ion hybrid capacitor with high energy density, including the selection of the active materials in cathode/anode and the separator, the pre-lithiation method using the three-electrode structure, the high- and low-temperature performances, …

Template Induced Fabrication Of Nitrogen Doped Carbon Sheets As Electrode Materials In Supercapacitors, Tao Huang, Guang-Zhi Tao, Chong-Qing Yang, Deng Lu, Lie Ma, Dong-Qing Wu

Journal of Electrochemistry

Due to the good electrical conductivity, high specific surface area, and excellent chemical/mechanical stability, carbon nanomaterials with two-dimensional morphology have gradually become the hot topic of the research on supercapacitors. Herein, we report for the first time the fabrication of nitrogen doped carbon sheets (NCSs). In our approach, the sheet-like magnisum aluminum (MgAl) layered double hydroxide was used as the hard template, which was mixed with o-phenylene diamine and iron chloride. The following thermal treatment could render the polymerization and carbonization of o-phenylene diamine. The NCSs with ordered hexagonal architectures were formed by final etching process of the thermally treated …