Engineering Science and Materials Commons^™

Minimizing Surface Run-Off, Improving Underground Water Recharging, And On-Site Rain Harvesting In The Kathmandu Valley, Ambika P. Adhikari, Keshav Bhattarai

Himalayan Research Papers Archive

Nepal's political institutions and administrative units were thoroughly restructured in 2015 with the promulgation of the new Constitution. Several rural areas were combined to meet the definition of urban threshold criteria to classify rural areas into urban categories. Accordingly, over 3,900 local political and administrative units were amalgamated into 753 units, of which, 293 units are classified as urban. Within these newly defined urban areas, many natural environments have been converted into impervious surfaces such as paved roads, sidewalks, and building roofs. These impervious surfaces have drastically increased the amount of surface run-offs-often termed as "urban floods"--under increasing precipitation caused …

Spatially Guided Construction Of Multilayered Epidermal Models Recapturing Structural Hierarchy And Cell–Cell Junctions, Haiwei Zhai, Xiaowei Jin, Grayson Minnick, Jordan Rosenbohm, Mohammed Abdul Haleem Hafiz, Ruiguo Yang, Fanben Meng

Department of Mechanical and Materials Engineering: Faculty Publications

A current challenge in 3D bioprinting of skin equivalents is to recreate the distinct basal and suprabasal layers and promote their direct interactions. Such a structural arrangement is essential to establish 3D stratified epidermis disease models, such as for the autoimmune skin disease pemphigus vulgaris (PV), which targets the cell– cell junctions at the interface of the basal and suprabasal layers. Inspired by epithelial regeneration in wound healing, a method that combines 3D bioprinting and spatially guided self-reorganization of keratinocytes is developed to recapture the fine structural hierarchy that lies in the deep layers of the epidermis.Herein, keratinocyteladen fibrin hydrogels …

Influence Of Defects On In-Plane Dynamic Properties Of Hexagonal Ligament Chiral Structures, Ning An, Xunwen Su, Dongmei Zhu, Mileta M. Tomovic

Engineering Technology Faculty Publications

Although the six-ligament chiral structure has many unique properties, due to its special structure, the stress concentration is prone to defects. In addition, additive manufacturing is also prone to defects. This paper studies the effect of defects, which is helpful for the better application of the six-ligament chiral structure. Several new six-ligament chiral structures with random and concentrated defects were designed to explore the effects of the defects on the in-plane dynamic properties. The structures were studied with the finite element ANSYS/LSDYNA numerical simulation and experimental methods. According to the defect-free six-ligament chiral structures exhibiting different deformation modes at different …

Biofilms: Formation, Research Models, Potential Targets, And Methods For Prevention And Treatment, Yajuan Su, Jaime T. Yrastorza, Mitchell Matis, Jenna Cusick, Siwei Zhao, Guangshun Wang, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Due to the continuous rise in biofilm-related infections, biofilms seriously threaten human health. The formation of biofilms makes conventional antibiotics ineffective and dampens immune clearance. Therefore, it is important to understand the mechanisms of biofilm formation and develop novel strategies to treat biofilms more effectively. This review article begins with an introduction to biofilm formation in various clinical scenarios and their corresponding therapy. Established biofilm models used in research are then summarized. The potential targets which may assist in the development of new strategies for combating biofilms are further discussed. The novel technologies developed recently for the prevention and treatment …

Quantitative Lithium Composite As 3d Lithium Foam Anode For Lithium Metal Battery, Hu-Dong Li, Wei-Shang Jia, Xin-Xiu Yan, Yao-Yue Yang

Journal of Electrochemistry

Lithium (Li) metal as an anode material for batteries has extremely high specific capacity and extremely low redox potential, which can significantly improve the energy density of the battery. However, the main problems faced by the use of Li metal anodes are Li dendrite growth, interfacial side reaction and volumetric change of electrode. Herein, a strategy to prepare the three-dimensional (3D) Li foam by combining 3D scaffold with quantitative Li was proposed to suppress Li dendrites growth and alleviate electrode volumetric change. The 3D Li foam facilitated the efficient utilization of Li metal by suppressing the Li dendrite growth, mitigating …

Low-Crystallinity And Heterostructured Aupt-Ru@Cnts As Highly Efficient Multifunctional Electrocatalyst, Tuan-Jie Gan, Jian-Ping Wu, Shi Liu, Wen-Jun Ou, Ling Bin, Xiong-Wu Kang

Journal of Electrochemistry

The catalytic activity of the catalysts is strongly dependent on the structure of the catalysts, and the exploration of their correlation and structure-controlled synthesis of the high-performance catalysts are always at the central. Currently, platinum (Pt) is the optimum catalyst for hydrogen evolution reaction (HER), oxygen reduction reaction (ORR) and alcohol oxidation reaction, while ruthenium (Ru) behaves as the champion catalyst for oxygen evolution reaction (OER) during water splitting. Preparing alloy catalysts with these precious metals can modulate the catalytic activity of these catalysts from the perspective of strain effect, ensemble effect and ligand effect. Here, we developed a strategy …

Optimized Electrochemical Performance Of Si@C Prepared By Hydrothermal Reaction And Glucose Carbon Source, Si Chen, Song-Sheng Zheng, Lei-Ming Zheng, Ye-Han Zhang, Zhao-Lin Wang

Journal of Electrochemistry

Silicon (Si) has been considered as the potential material for the next-generation lithium-ion batteries (LIBs) for its high capacity (4200 mAh·g^-1, Li₂₂Si₅) and suitable working voltage (about 0.25 V vs. Li/Li⁺). However, the cycling stability and electrochemical performance of Si anode become significant challenges because of low intrinsic conductivity and huge volume variation (about 400%) during cycling processes. In addition, the repeated formation and destruction of surface solid electrolyte interphase (SEI) film will continuously consume the electrolyte and cause damage to LIBs. Carbon (C) materials, such as graphite, carbon spheres and tubes, …

Facile One-Step Solid-State Synthesis Of Ni-Rich Layered Oxide Cathodes For Lithium-Ion Batteries, Jing-Yue Wang, Rui Wang, Shi-Qi Wang, Li-Fan Wang, Chun Zhan

Journal of Electrochemistry

Nickel-rich layered oxide is one of the dominate cathode materials in the lithium ion batteries, due to its high specific energy density meeting the range requirement of the electric vehicles. Typically, the commercial Ni-rich layered oxides are synthesized from co-precipitated precursors, while precision control is required in the co-precipitation process to ensure the atomic level mixing of the cations such as Ni, Co and Mn, et.al. In this work, a one-step solid-state method was successfully applied to synthesize the Ni-rich layered oxide materials with ultra-high Ni content. By choosing the nickel hydroxides as the precursor with layered structure similar to …

Waste Plastic Direct Extrusion Hangprinter, Aliaksei Petsiuk, Bharath Lavu, Rachel Dick, Joshua M. Pearce

Michigan Tech Publications, Part 1

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel, open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression-screw-based end-effector that allows for the direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste …

Comparative Study Of Tapered Versus Conventional Cylindrical Balloon For Stent Implantation In Stenotic Tapered Artery, Xiang Shen, Jiabao Jiang, Hongfei Zhu, Kaikai Lu, Pengfei Dong, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The natural tapering of coronary arteries often creates a dilemma for optimal balloon sizing during stenting. The influence of different balloon types, namely, a tapered balloon and a conventional cylindrical balloon, on the mechanical performance of the stent as well as arterial mechanics was investigated via the finite element method. Stent free-expansion and stent deployment in a stenotic tapered artery were investigated numerically. The biomechanical behavior of the two balloon types was compared in terms of stent foreshortening, stent deformation, stent stress distribution, and arterial wall stress distribution. Results indicate that balloon types affect the transient behavior of the stent …

Three-Dimensional Printed Abdominal Imaging Windows For In Vivo Imaging Of Deep-Lying Tissues, Mitchell Kuss, Ayrianne J. Crawford, Olawale A. Alimi, Michael A. Hollingsworth, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

The ability to microscopically image diseased or damaged tissue throughout a longitudinal study in living mice would provide more insight into disease progression than having just a couple of time points to study. In vivo disease development and monitoring provides more insight than in vitro studies as well. In this study, we developed permanent 3D-printed, surgically implantable abdominal imaging windows (AIWs) to allow for longitudinal imaging of deep-lying tissues or organs in the abdominal cavity of living mice. They are designed to prevent organ movement while allowing the animal to behave normally throughout longitudinal studies. The AIW also acts as …

Modeling The Effects Of Mechanical Loading On Hypertrophic Cardiomyopathy Pathogenesis In Human Induced Pluripotent Stem Cell Derived Micro Heart Muscle, Jingxuan Guo

McKelvey School of Engineering Graduate Student Theses & Dissertations

Sudden cardiac death in the young is devastating. Advances in genetics have associated mutations in the contractile sarcomere apparatus of cardiomyocytes with hypertrophic cardiomyopathy, the most frequent cause of sudden cardiac death in the young. Currently, it is challenging to predict genotype-phenotype relationships in hypertrophic cardiomyopathy due to its incomplete disease penetrance. For example, different patients from the same family with identical genomic variants develop different symptoms. Non-genetic, environmental factors such as blood pressure are critical in heart function and disease. Therefore, understanding how mechanical factors contribute to phenotypes in diseases like hypertrophic cardiomyopathy is critical for developing effective therapeutics. …

Synthesis And Consolidation Of Metal Oxide Nanocrystals Via Nonthermal Plasma, Austin Cendejas

McKelvey School of Engineering Graduate Student Theses & Dissertations

Nonthermal plasmas offer a unique nonequilibrium environment that has been leveraged in a wide variety of applications in the fields of material processing, lighting, and waste management to name a few. In all of these cases, the plasma serves as a source of high energy electrons, ions, reactive gas species, and radicals that interact in several ways with surfaces brought into contact with the plasma. Specifically, nonthermal plasmas have been shown to be very successful in achieving continuous, high-throughput, monodisperse nanocrystals of a wide variety of materials. The crystallinity of nanoparticles synthesized in nonthermal plasmas can be attributed to the …

Plasmonic Nanomaterials-Based Point-Of-Care Biosensors, Rohit Gupta

McKelvey School of Engineering Graduate Student Theses & Dissertations

Point-of-care (POC) biosensors, although rapid and easy-to-use, are orders magnitude less sensitive than laboratory-based tests. Further they are plagued by poor stability of recognition element thus limiting its widespread applicability in resource-limited settings. Therefore, there is a critical need for realizing stable POC biosensors with sensitivity comparable to gold-standard laboratory-based tests. This challenge constitutes the fundamental basis of this dissertation work– to expand access to quality and accurate biodiagnostic tools. At the heart of these solutions lies plasmonic nanoparticles which exhibit unique optical properties which are attractive for label-free and labelled biosensors.Firstly, we improve the stability and applicability of label-free …

Soft Electronics And Sensors For Wearable Healthcare Applications, Li-Wei Lo

McKelvey School of Engineering Graduate Student Theses & Dissertations

Wearable electronics are becoming increasingly essential to personalized medicine by collecting and analyzing massive amounts of biological signals from internal organs, muscles, and blood vessels. Conventional rigid electronics may lead to motion artifacts and errors in collected data due to the mismatches in mechanical properties between human skin. Instead, soft wearable electronics provide a better platform and interface that can form intimate contact and conformably adapt to human skin. In this respect, this thesis focuses on new materials formulation, fabrication, characterization of low-cost, high sensitivity and reliable sensors for wearable health monitoring applications.

More specifically, we have studied the silver …

Design Of Multi-Principal Element Materials Using A Combination Of First-Principles Calculations And Machine Learning, Zhaohan Zhang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Multiple-principal element materials, including alloys (MPEAs), oxides and other compounds combine several elements on a sub-lattice, which increases the configurational entropy and contributes to their thermodynamic stability. The vast combinatorial design space of multi-principal element materials gives rise to diverse microstructures and unprecedent combination of properties. It also poses a challenge—how to rapidly screen MPEAs with stability and properties for targeted applications. Furthermore, fundamental composition-structure-property relationships in MPEAs are currently missing. In this dissertation, I have used MPEAs as a representative system and investigated the role of chemical composition on their phase-stability and mechanical properties. With a combination of first-principles …

The Generation And Transport Of Charged Aerosols: Fundamental Study And Applications In Medicine And Energy Conversion, Hao Zhou

McKelvey School of Engineering Graduate Student Theses & Dissertations

Charged aerosols have significant implications in the field of functional material synthesis, pharmaceutical coating, and drug delivery. Electrospray systems are an effective methodology for generating highly charged monodispersed droplets in the size range from nanometer to micrometer. The prediction of surface charge, size and morphology of nanoparticles resulting from charged droplets are highly required for the precise control of nanoparticle properties and their effective utilization. However, the evolution of charged droplet is not well understood due to the existence of coulombic fission and ion evaporation processes. Thus, the goal of this dissertation is to elucidate how the precursor properties and …

Testing Oxygenated Microbubbles Via Intraperitoneal And Intrathoracic Routes On A Large Pig Model Of Lps-Induced Acute Respiratory Distress Syndrome, Riaz Ur Rehman Mohammed, Nathaniel T. Zollinger, Andrea R. Mccain, Roser Romaguera-Matas, Seth P. Harris, Keely L. Buesing, Mark A. Borden, Benjamin S. Terry

Department of Mechanical and Materials Engineering: Faculty Publications

With a mortality rate of 46% before the onset of COVID-19, acute respiratory distress syndrome (ARDS) affected 200,000 people in the US, causing 75,000 deaths. Mortality rates in COVID-19 ARDS patients are currently at 39%. Extrapulmonary support for ARDS aims to supplement mechanical ventilation by providing life-sustaining oxygen to the patient. A new rapid-onset, human-sized pig ARDS model in a porcine intensive care unit (ICU) was developed. The pigs were nebulized intratracheally with a high dose (4 mg/kg) of the endotoxin lipopolysaccharide (LPS) over a 2 h duration to induce rapid-onset moderate-to- severe ARDS. They were then catheterized to monitor …

Vibrating Flexoelectric Micro-Beams As Angular Rate Sensors, Yilin Qu, Feng Jin, Jiashi S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied flexoelectrically excited/detected bending vibrations in perpendicular directions of a micro-beam spinning about its axis. A set of one-dimensional equations was derived and used in a theoretical analysis. It is shown that the Coriolis effect associated with the spin produces an electrical output proportional to the angular rate of the spin when it is small. Thus, the beam can be used as a gyroscope for angular rate sensing. Compared to conventional piezoelectric beam gyroscopes, the flexoelectric beam proposed and analyzed has a simpler structure.

Vibrating Flexoelectric Micro-Beams As Angular Rate Sensors, Yilin Qu, Feng Jin, Jiashi S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied flexoelectrically excited/detected bending vibrations in perpendicular directions of a micro-beam spinning about its axis. A set of one-dimensional equations was derived and used in a theoretical analysis. It is shown that the Coriolis effect associated with the spin produces an electrical output proportional to the angular rate of the spin when it is small. Thus, the beam can be used as a gyroscope for angular rate sensing. Compared to conventional piezoelectric beam gyroscopes, the flexoelectric beam proposed and analyzed has a simpler structure.

Geometric Analysis Of Insect Wing Vein Network, Jacob White, Ying Hu, Sangjin Ryu, Seunghee Kim, Haipeng Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

An insect wing consists of a thin membrane supported by a system of veins, and flow of blood through the system of veins is critical for maintaining healthy insect wings. Better understanding of the insect wing vein circulation requires to know how the efficiency of blood flow in an insect wing relates to the geometric shape of the vein. Our investigation of the wing vein network of a dragonfly Anax junius follows the idea of Murray’s law, which is established in the study of efficiency of the vein network and the geometric shape of the vein. Instead of using the …

Pressure-Induced Phase Transition And Electronic Structure Changes In Equiatomic Fev, Homero Reyes Pulido

Open Access Theses & Dissertations

Classical molecular dynamics methods can accurately describe a broad set of many-atomssystems. Although more economical, the results given by this framework lack the precision capable of density functional theory (DFT). Therefore, the structural stability of the B2 phase of a body-centered-cubic iron-vanadium (FeV) alloy using DFT on the electronic structure level is analyzed to verify and further explain classical results obtained by our group in this same alloy. Using Quantum Espresso and Phonopy for the computational simulations, the plotted band structure, electronic density of states (eDOS), phonon dispersions, charge density, and Fermi surfaces for various compressed unit cells are presented. …

Characterization Of 3d Stereolithography (Sla) Printed Polymer For Autonomous-Flow Microfluidic Devices, Michelle Gamboa

Open Access Theses & Dissertations

3D Stereolithography (SLA) printing is a high-throughput, precise and reproducible manufacturing platform which makes it a desirable technique to develop microfluidic devices for bioanalytical applications. However, limited information exists regarding the physical, chemical, and biological properties of the polymer resins used in 3D SLA printing. This project demonstrates the characterization of a commercially available 3D SLA printed resin polymer used to develop an autonomous-flow (self-driven) microfluidic device. In this investigation, time-dependent materials characterization was done on the Formlabs clear V4 resin to observe changes in mechanical and surface properties. The clear, printed polymer was analyzed with attenuated total reflectance (ATR), …

Reflectance Spectral Characterization And Taxonomy Applications Of Spacecraft Materials To Aid Space Situational Awareness, Jacqueline Andrea Reyes

Open Access Theses & Dissertations

The increasing number of space missions involving successfully deployed spacecraft have resulted in an augmented density of artificial objects positioned in orbital domains near Earth. With this steady accumulation of objects in space, it has become increasingly imperative to characterize spacecraft materials, which may ultimately be contributors to the orbital debris population. In an effort to identify unique material-specific spectroscopic markers, a variety of spacecraft materials frequently utilized in the aerospace industry to construct typical spacecraft were analyzed using reflectance spectroscopy as a characterization technique for assessment on material type according to optical features. This is significant in providing information …

Additive Manufacturing Of Aluminum Alloy By Metal Fused Filament Fabrication (Mf3)., Luke J. Malone

Electronic Theses and Dissertations

This research studies metal-fused filament fabrication (MF3) for manufacturing aluminum alloy parts. An aluminum alloy powder-based feedstock with a polymer-binder system was extruded via capillary rheometry to form a filament. The filament was used to print green parts that were involved in a two-step debinding process combining solvent and thermal extraction of the polymer binder, then sintered in a partial vacuum. Resulting grain structure, sintered density, and mechanical properties will be characterized and compared to metal injection molded (MIM) specimens. The main objective is to gain an understanding of the MF3 process characteristics and the ensuing material properties and microstructure …

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

Study Of Thermoelectric And Lattice Dynamics Properties Of 2d Layered Mx (M = Sn, Pb; X = S, Se, Te) And Zrs2 Compounds Using First-Principles Approach, Abhiyan Pandit

Graduate Theses and Dissertations

The aim of this dissertation is the investigation of thermoelectric and lattice dynamics properties of two-dimensional (2D) MX (M = Sn, Pb; X = S, Se, Te) and ZrS2 compounds based on the first-principles density functional theory. The dimensionality reduction (e.g., using 2D structure) of bulk materials is found to have enhanced thermoelectric efficiency. This enhancement is attributed to the increase of the Seebeck coefficient as a result of higher electronic density of states near the Fermi level in low-dimensional materials. In addition, lowering the dimensionality increases phonon scattering near interfaces and surfaces in 2D materials, which leads to a …

Etching Process Development For Sic Cmos, Weston Reed Renfrow

Graduate Theses and Dissertations

Silicon Carbide (SiC) is an exciting material that is growing in popularity for having qualities that make it a helpful semiconductor in extreme environments where silicon devices fail. The development of a SiC CMOS is in its infancy. There are many improvements that need to be made to develop this technology further. Photolithography is the most significant bottleneck in the etching process; it was studied and improved upon. Etching SiC can be a challenge with its reinforced crystal structure. Chlorine-based inductively coupled plasma (ICP) etching of intrinsic SiC and doped SiC, SiO2, and Silicon has been studied. A baseline chlorine …

Passive Prosthetic Ankle Design Based On Indonesian Anthropometry, Wahyu Dwi Lestari

Journal of Mechanical Engineering Science and Technology (JMEST)

Foot prosthesis is a replacement for the foot to overcome activity limitations due to disease, birth defects, accidents, or amputations. Many foot prosthetics have been developed in recent years to treat patients. However, prostheses on the market today have drawbacks, including their high price, lack of comfort, stiff ankles, and low durability. The main objective of this study is to develop an existing ankle-foot prosthesis design that approximates the resemblance of a human foot according to the anthropometry of Asians, especially Indonesians. This study contains the design of a prosthetic foot with a skin design model and a support core. …

Surface Quality Of Fe, Ni And Cr Added Hyper-Eutectic Al-Si Automotive Alloys Under Up-Milling And Down-Milling Operation, Akib Abdullah Khan, Mashiur Rahman Shoummo, Mohammad Salim Kaiser

Journal of Mechanical Engineering Science and Technology (JMEST)

Effect of the elements Fe, Ni, and Cr on the surface quality under machining of hyper-eutectic aluminiumbased Al-Si automotive alloys has been carried out as the elements improve the properties of this alloy. Machining is done on a horizontal type milling machine using a high-speed steel slab milling cutter in dry condition. Only the cutting speed varies throughout the experiment, while the machining feed and depth of cut remain fixed. The experimental results show that the addition of these alloying elements increases the roughness and hardness specially due to formation of Fe-rich intermetallic ��-����5��������. However, the needle-like ��-����5�������� has been …