Robotics Commons^™

Kinematic Modeling Of An Automated Laser Line Scanning System, Kiran Sunil Deshmukh

Wayne State University Theses

This research work describes the geometric coordinate transformation in an automated laser line scanning system caused by movements required for scanning a component surface. The elements of an automated laser scanning system (robot, laser line scanner, and the component coordinate system) function as a mechanical linkage to obtain a trajectory on a component surface. This methodology solves the forward kinematics, derives the component surface, and uses inverse kinematic equations to characterize the movement of the entire automated scanning system on point trajectory. To reach a point on the component, joint angles of robot have been calculated. As a result, trajectory …

An Evaluation Of Robotics In Nursing Homes To Reduce Adverse Drug Events, Ozell Ueal Jr.

Walden Dissertations and Doctoral Studies

Adverse drug events (ADE) cause many deaths annually in addition to affecting the quality of life of many others. The descriptive mixed methods approach, specifically exploratory case study and experimental design that guided this research utilized the survey and focus group methods to evaluate perceptions about robotic technology (RT) to reduce the rate of ADEs in U.S. nursing homes (NH). There is a lack of scholarly research into whether a conceptual approach rooted in RT can be implemented to assist with drug administrations in NHs. The purpose of this study was twofold. The first purpose was to evaluate the causes …

Localization And Mapping Of Unknown Locations And Tunnels With Unmanned Ground Vehicles, Doris Turnage

Electronic Theses and Dissertations

The main goals of this research were to enhance a commercial off the shelf (COTS) software platform to support unmanned ground vehicles (UGVs) exploring the complex environment of tunnels, to test the platform within a simulation environment, and to validate the architecture through field testing. Developing this platform will enhance the U. S. Army Engineering Research and Development Center’s (ERDC’s) current capabilities and create a safe and efficient autonomous vehicle to perform the following functions within tunnels: (1) localization (e.g., position tracking) and mapping of its environment, (2) traversing varied terrains, (3) sensing the environment for objects of interest, and …

Teaching Robot Kinematics For Engineering Technology Students Using A Created Three-Dimensional Robot And Camera, Cheng Y. Lin, Yuzhong Shen

Engineering Technology Faculty Publications

Teaching robot kinematics is important to engineering technology students in the robot automation. The study can help students not only in the coordinate transformation principles from a joint to its following joint in a robot, but also in relating the coordinate systems between a robot and a machine vision system. While students can utilize math software to compute robot kinematic transformations, they have problems verifying their answers. In this paper, a three dimensional vertically articulated robot is created to help students visualize the location and orientation of the end effector. Students can check their robot kinematic answers based on the …

Robots As Legal Metaphors, Ryan Calo

Articles

This Article looks at the specific role robots play in the judicial imagination. The law and technology literature is replete with examples of how the metaphors and analogies that courts select for emerging technology can be outcome determinative. Privacy law scholar Professor Daniel Solove argues convincingly, for instance, that George Orwell's Big Brother metaphor has come to dominate, and in ways limit, privacy law and policy in the United States. Even at a more specific, practical level, whether a judge sees email as more like a letter or a postcard will dictate the level of Fourth Amendment protection she is …

Robot Fish Do Not Need Sentience, Antonio Chella

Animal Sentience

The target article by Key (2016) discusses the thesis that fish cannot feel pain because of the lack of the necessary neural structure. This commentary suggests the possibility that fish do not need conscious neural processing by taking into account recent results from biomimetic robotics. State-of-the-art biomimetic robot fish are based on a tight interaction between the body and the environment and are typically controlled by behavior-based architectures. Therefore, it can be hypothesized that cognitive architectures are not needed to control a robot fish. This is in line with the thesis proposed by Key: what biomimetic robot fish show is …

How Can We Build A Moral Robot?, Kristen E. Clark

Capstones

Artificial intelligence is already starting to drive our cars and make choices that affect the world economy. One day soon, we’ll have robots that can take care of our sick and elderly, and even rescue us in rescue us in emergencies. But as robots start to make decisions that matter—it’s raising questions that go far beyond engineering. We’re stating to think about ethics.

Bertram Malle and Matthias Scheutz are part of a team funded by the department of defense. It's their job to answer a question that seems straight out of a sci-fi novel: How can we build a moral …

A Lidar Based Semi-Autonomous Collision Avoidance System And The Development Of A Hardware-In-The-Loop Simulator To Aid In Algorithm Development And Human Studies, Thomas F. Stevens

Master's Theses

In this paper, the architecture and implementation of an embedded controller for a steering based semi-autonomous collision avoidance system on a 1/10^th scale model is presented. In addition, the development of a 2D hardware-in-the-loop simulator with vehicle dynamics based on the bicycle model is described. The semi-autonomous collision avoidance software is fully contained onboard a single-board computer running embedded GNU/Linux. To eliminate any wired tethers that limit the system’s abilities, the driver operates the vehicle at a user-control-station through a wireless Bluetooth interface. The user-control-station is outfitted with a game-controller that provides standard steering wheel and pedal controls along …

Kinematic Control Of Redundant Mobile Manipulators, Mustafa Mashali

USF Tampa Graduate Theses and Dissertations

A mobile manipulator is a robotic arm mounted on a robotic mobile platform. In such a system, the degrees of freedom of the mobile platform are combined with that of the manipulator. As a result, the workspace of the manipulator is substantially extended. A mobile manipulator has two trajectories: the end-effector trajectory and the mobile platform trajectory. Typically, the mobile platform trajectory is not defined and is determined through inverse kinematics. But in some applications it is important to follow a specified mobile platform trajectory. The main focus of this work is to determine the inverse kinematics of a mobile …

Optimal Control Of Dc Motors Using Pso Algorithm For Tuning Pid Controller, Arnisa Myrtellari, Petrika Marango, Margarita Gjonaj

UBT International Conference

The DC motors are widely used in the mechanisms that require control of speed. Different speed can be obtained by changing the field voltage and the armature voltage. The classic PID controllers are widely used in industrial process for speed control. But they aren’t suitable for high performance cases, because of the low robustness of PID controller. So many researchers have been studying various new control techniques in order to improve the system performance and tuning PID controllers. This paper presents particle swarm optimization (PSO) method for determining the optimal PID controller parameters to find the optimal parameters of DC …

Database For Online Accreditation Process In Directorate For Accreditation Of Kosovo (Dak-Mis), Ibush Luzha

UBT International Conference

Directorate for Accreditation of Kosovo (DAK) is only National Accreditation Body in Republic of Kosovo, recognized by Government, which in accordance with international standards, assesses technical competences of the Conformity Assessment Bodies (CAB)s that deal with activities such as: testing, calibration, certification and inspection both in public and private sector. Till now application for accreditation and all other procedures for accreditation of CABs are carried out so that all the documents of the application and the receipt of the certificate of accreditation are conducted in the offices of DAK. By Management Information System (MIS), database of DAK (DAK-MIS), customers will …

Noise Reduction In Quadcopter Accelerometer And Gyroscope Measurements Based On Kalman Filter, Bertan Karahoda, Xhemajl Mehmeti, Uran Cabra

UBT International Conference

The Accelerometer and Gyroscope modules used for measuring the orientation of the quadcopter usually generate noisy signals which directly affect the control strategies. The high speed motors used in quadcopters cause high noise levels which makes the real time control almost impossible. In this work the Kalman filter is applied to the noisy measurements obtained from accelerometer and gyroscope modules. The measurements are conducted for two cases: Motors stopped, and Motors activated at high speed. The Kalman filtering is applied separately for each measurement and the obtained results show noticeable improvement in noise level for two cases. The joint implementation …

“New” Subjects In Mechatronics Management Education, Peter Kopacek

UBT International Conference

Process – and manufacturing automation as well as robotics are currently one of the fast growing fields in automation. Advanced process control, cyber-physical systems, industry 4.0 and “advanced robots” are no longer a headline. They are in realization. As a consequence of these developments new social, ethical and human questions appear. Therefore this contribution is a first report about the continuous “modernization” of the Mechatronics Management BSc and MSc programs which are successful running at UBT. Both programs were developed in the framework of two TEMPUS projects from an international consortium from 2006 to 2009. Since that time new “buzzwords” …

Planning, Development And Application Of Mechatronics Systems As Students Work, Muzafer Shala, Valmir Hoxha

UBT International Conference

In Kosovo universities in general there is a lack of students practical work, this fact is one of the reasons why in Kosovo are no sufficient number of professionals to fill the market needs. The aim of this work is to go through the steps of conceptualisation, development and application of a Mechatronics Systems with students. Also in this project students work on all the phases of the work which we consider to be of great benefit. The work was organised as it would be on a real life company, students were split on groups and the groups worked in …

Real-Time Topic And Sentiment Analysis In Human-Robot Conversation, Elise Russell

Master's Theses (2009 -)

Socially interactive robots, especially those designed for entertainment and companionship, must be able to hold conversations with users that feel natural and engaging for humans. Two important components of such conversations include adherence to the topic of conversation and inclusion of affective expressions. Most previous approaches have concentrated on topic detection or sentiment analysis alone, and approaches that attempt to address both are limited by domain and by type of reply. This thesis presents a new approach, implemented on a humanoid robot interface, that detects the topic and sentiment of a user’s utterances from text-transcribed speech. It also generates domain-independent, …

Using Eye And Head Movements As A Control Mechanism For Tele-Operating A Ground-Based Robot And Its Payload, Kathryn C. Hicks

Computational Modeling & Simulation Engineering Theses & Dissertations

To date, eye and head tracking has been used to indicate users' attention patterns while performing a task or as an aid for disabled persons, to allow hands-free interaction with a computer. The increasing accuracy and the reduced cost of eye- and head-tracking equipment make utilizing this technology feasible for explicit control tasks, especially in cases where there is confluence between the visual task and control.

The goal of this research was to investigate the use of eye-tracking as a more natural interface for the control of a camera-equipped, remotely operated robot in tasks that require the operator to simultaneously …

3d Scene Reconstruction With Micro-Aerial Vehicles And Mobile Devices, Ivan Dryanovski

Dissertations, Theses, and Capstone Projects

Scene reconstruction is the process of building an accurate geometric model of one's environment from sensor data. We explore the problem of real-time, large-scale 3D scene reconstruction in indoor environments using small laser range-finders and low-cost RGB-D (color plus depth) cameras. We focus on computationally-constrained platforms such as micro-aerial vehicles (MAVs) and mobile devices. These platforms present a set of fundamental challenges - estimating the state and trajectory of the device as it moves within its environment and utilizing lightweight, dynamic data structures to hold the representation of the reconstructed scene. The system needs to be computationally and memory-efficient, so …

Dual 7-Degree-Of-Freedom Robotic Arm Remote Teleoperation Using Haptic Devices, Yu-Cheng Wang

USF Tampa Graduate Theses and Dissertations

A teleoperated system of dual redundant manipulator will be controlled in this thesis. The robot used with the dual redundant manipulator in this thesis is Baxter. Baxter’s redundant robot arms are 7-degree-of-freedom arms. The problem that will be solved in this thesis is optimization of the 7-degree-of-freedom robot arms. The control algorithm of the 7-degree-of-freedom robot arms will be discussed and built. A simulation program will be built to test the control algorithm. Based on the control algorithm, a teleoperation system will be created for Baxter. The controller used is Omni, which is a six-joint haptic device. Omni will also …

The Design And Implementation Of An Adaptive Chess Game, Mehdi Peiravi

Electronic Theses, Projects, and Dissertations

In recent years, computer games have become a common form of entertainment. Fast advancement in computer technology and internet speed have helped entertainment software developers to create graphical games that keep a variety of players’ interest. The emergence of artificial intelligence systems has evolved computer gaming technology in new and profound ways. Artificial intelligence provides the illusion of intelligence in the behavior of NPCs (Non-Playable-Characters). NPCs are able to use the increased CPU, GPU, RAM, Storage and other bandwidth related capabilities, resulting in very difficult game play for the end user. In many cases, computer abilities must be toned down …

Novelty Wins, “Straight Toward Objective” Loses! Or Book Review: Why Greatness Cannot Be Planned: The Myth Of The Objective, By Kenneth O. Stanley And Joel Lehman, Reuben Hersh

Journal of Humanistic Mathematics

Experiments in evolutionary artificial intelligence demonstrate that progress toward an important, difficult goal is not best achieved by attempting to go directly toward that goal, but rather, by rewarding novelty.

Roborodentia Robot, Jordan Dykstra, Anibal Hernandez, Robert Prosser

Computer Engineering

This report provides details on the design and implementation of a robot for the Spring 2015 Roborodentia competition. The system is described from a software perspective, a hardware perspective, and a mechanical design perspective.

Printed Circuit Board For Introductory Animatronics Course, Preston Brown

Computer Engineering

For many years, freshmen Computer Engineering students at California Polytechnic State University have taken a course that introduces them to the “processes of electronics manufacturing. They are lectured on concepts such as CAD/CAM design, Design for Manufacture (DFM), documentation requirements, prototyping and production planning”. The laboratory portion of the course allows students to “use hands-on techniques to solidify knowledge of project planning, soldering, automation, hand tool usage and production methods” by manufacturing their own power supply, starting with aluminum sheets, a bag of components, and and an unassembled printed circuit board (PCB).

While the project is popular among students, department …

Roborodentia Robot 2015, Travis Stuever

Computer Engineering

The Roborodentia 2015 competition was a ring based challenge that had participants move PVC rings from one side of a course to another all within 3 minutes. In order to succeed in this competition there needs to be a good robotic design, thought out use cases, and good solid software.

Universal Uav Payload Interface, Nolan Reker, David Troy Jr, Drew Troxell

Computer Engineering

Unmanned Aerial Vehicle (UAV) technology is becoming increasingly accessible for civilian use. Both open-source and commercial-purpose UAVs can be obtained affordably or even built. However, the platforms available are very segmented in their customization to a specific application (i.e. land surveying, payload delivery). This project aims to create a Universal Payload Interface (UPI) mounted to the underside of multi-rotors or other UAVs to enable the attachment of customizable sensor payloads. These payloads allow a single UAV to be rapidly reconfigured to perform a multitude of tasks.

The Universal Payload Interface facilitates communication between the payload, onboard flight controller, and operator …

Pl-X (Roborodentia), Kelly Leung, William Luo, Jeffrey Tang

Computer Engineering

Pl-x is the name of the robot that will be competing in Roborodentia, an annual autonomous robot competition. This year the competition involves moving rings from one end of a course to the opposite end of the course.

Innovative Connectivity Ensuring Education (I.-C.E.E.), Luke Cole, Andrew Ma, Nicholas Ross, Daniel Williams

Electrical Engineering

This is the critical design review for the Telepresence/Telerobotic Technology for Children with Disabilities Project by team I.- C.E.E. (Innovative Connectivity Ensuring Education). This report details our telepresence system design for our client (Nathan Stilts) including design choices/justification, testing verification and procedures, and chosen components for implementation. There are seven chapters in total starting with introductory/background information followed by hardware and software design, verification, and testing and concludes with the current status of the project and what future work may need to be included.

Telepresence: Design, Implementation And Study Of An Hmd-Controlled Avatar With A Mechatronic Approach, Darren Michael Chan

Master's Theses

Telepresence describes technologies that allow users to remotely experience the sensation of being present at an event without being physically present. An avatar exists to represent the user whilst in a remote location and is tasked to collect stimuli from its immediate surroundings to be delivered to the user for consumption. With the advent of recent developments in Virtual Reality technology, viz., head-mounted displays (HMDs), new possibilities have been enabled in the field of Telepresence. The main focus of this thesis is to develop a solution for visual Telepresence, where an HMD is used to control the direction of a …

Motion In The Field: A Study Of Movement In Computer Science, Catherine Martin

Renée Crown University Honors Thesis Projects - All

In this project, I use a system that combines the use of a motion controller to obtain information about physical motion of a user with the transmission of outputs to a quadcopter that interacts with the physical environment. In the manual mode, the user sends commands to the quadcopter using hand controls. I utilized an existing system but increased usability to prevent accidental flight and created commands that are more intuitive for the user. In the automatic mode, the user gives a single command to the motion controller and it runs the A* path planning algorithm over a representation of …

Object Tracking Through The Use Of Color Hue Image Processing, Zachary R. Sabey

Electrical Engineering Undergraduate Honors Theses

Many industrial and commercial applications today are beginning to use autonomous systems to increase productivity and cut costs in production and manpower. Most of these applications are only semi autonomous; they still need assistance from a human to either start up or receive continual instructions. With the improvement of image processing techniques, camera processing capabilities and more efficient vehicles, a new wave of fully autonomous vehicles can be implemented. A simple system that uses a dedicated image processor connected to an RC vehicle can be developed to provide an example for the new techniques currently available. The Pixycam, a dedicated …

Formal Specification And Refinement Of The Navigation Tasks Of Autonomous Robots, Eman Rabiah

Theses

Autonomous robots are hybrid systems whose role in our daily life is becoming increasingly critical. They are tasked with various activities requiring reliability, safety, and correctness of their software-controlled behavior. Formal methods have been proved effective in addressing development issues associated with these software qualities. However, even though autonomous robot navigation is a primordial function, there is no research dealing with enhancing reliability of the navigation algorithms. Thus, our focus is to investigate this type of algorithms, and specifically path planning, a fundamental and critical functionality supporting autonomy. We formally address the issue of enhancing reliability of the widely-used A* …