Digital Commons Network^™

An Explicit, Dynamic Finite Element Model For The Local Failure Of Cold-Formed Trapezoidal Sheeting, Hèrm Hofmeyer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Trapezoidal sheeting, made of cold-formed, thin-walled steel, is widely used for the construction of cladding and roofs. At an interior support, the sheeting is subject to bending moments and a concentrated load, which leads to possible failure followed by two post-failure modes: the yield-arc and yield-eye modes. Until recently, it was not fully understood why a specific post-failure mode occurs and it was suggested that mode-jumping of the compressed sheeting flange may influence the mode occurring. This paper presents new research, in which both the compressed flange in isolation and the sheeting are modeled by using an explicit, dynamic finite …

The Role Of Transport Phenomena In The Direct Oxidation Of Solid Fuels, Charles J. Banas

Master's Theses

Direct carbon fuel cells have shown promise for stationary power generation by utilizing the direct oxidation of a solid carbon fuel source at the anode. In laboratory settings, researchers have reported up to 300mA/cm2 of current density from these cells types which suffer from mass transport losses. This paper studies the surface properties of the solid fuel source, and describes the process of CO2 evolution through an analogy to pool boiling. In nucleate boiling (a subset of pool boiling) vapor bubbles grow from nucleation sites where gas are trapped in micro-cavities on the surface. Carbon surfaces possess these same features, …

Faculty And Staff Breakfast Remarks, Richard F. Wilson

Remarks and Messages

No abstract provided.

Guitar Program At Iwu, Sherry Wallace

News and Events (Discontinued Series)

No abstract provided.

Academic Calendar | School Of Professional Development For 2012, Fall [Extended Session] | Class Schedule, Office Of The Registrar, Stony Brook University

Calendars

No abstract provided.

New Faculty And Staff Join Iwu, Sherry Wallace

News and Events (Discontinued Series)

No abstract provided.

Effects Of Cold-Formed Steel Framed Gypsum Partition Walls On The Seismic Response Of A Medical Facility, Ryan Davies, Rodrigo Retamales, Gilberto Mosqueda, Andre Filiatrault, Don Allen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The first experimental phase of the NEES Nonstructural Grand Challenge Project: “Simulation of the Seismic Performance of Nonstructural Systems” investigated the in-plane hysteretic behaviors of thirty-six full-scale cold-formed steel framed gypsum partition walls. Results of quasi-static reverse cyclic and dynamic testing on sixteen wall configurations including walls with commercial and institutional construction details and innovative connection techniques are first briefly reviewed. Thereafter, six tri-linear hysteretic models of partition walls with pinching behavior and strength and stiffness degradation are developed based on the experimental data for use in a finite element analysis platform. The partition wall models, represented by shear spring …

Characterizaiton Of Cold-Formed Steel Shear Wall Behavior Under Cyclic Loading For The Cfs-Nees Building, P. Liu, K. D. Peterman, C. Yu, B. W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The objective of this paper is to provide a full hysteretic characterization of OSB sheathed cold-formed steel (CFS) shear walls designed for use in the National Science Foundation funded Network for Earthquake Engineering Simulation (NEES) project: CFS-NEES (www.ce.jhu.edu/cfsnees). The shear walls were designed for a two-story ledger-framed building (i.e., the CFS-NEES building) that will undergo full-scale shake table testing at the University of Buffalo NEES site. Shear walls in real construction, such as the CFS-NEES building, have details that differ from the shear walls tested and provided for strength prediction in standards such as AISI-S213-07. Differences include: (a) ledger (rim …

Design Capacity Determination Assisted By Testing Based On Lrfd Method, Y. Q. Li, L. P. Wang, Z. Y. Shen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In some special circumstances of structural design, adequate calculation models are not available in current specifications or they cannot be used directly for new materials or structural configurations. In these cases, tests of the prototype units may be accepted as an alternative to calculation. If this alternative procedure is adopted, corresponding requirements and evaluation of test results should apply. In this paper, a complete procedure of determining the design capacity of the test specimens based on statistical analysis and Load and resistance factor design (LRFD) method was presented: characteristic value of experimental resistance was obtained from the minimum value of …

Critical Elastic Shear Buckling Stress Hand Solution For C- And Z-Sections Including Cross-Section Connectivity, Kevin Aswegan, Cristopher D. Moen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper presents an approximate solution for the critical elastic buckling stress of cold-formed steel C- and Z-section members including cross-section connectivity. The elastic buckling solution is developed to support the extension of the Direct Strength Method to the shear ultimate limit state, where the cross sectional critical elastic shear buckling stress (load) is employed to predict shear capacity. The shear buckling stress and buckled half-wavelength are calculated with a classical energy solution for a thin plate with edges rotationally restrained. Rotational stiffness expressions in the AISI S100-07 specification, originally derived for distortional buckling of C- and Z-sections, are used …

Load Distribution In Floor To Wall Connections, D. M. Fox, D. R. Knill, R. M. Schuster

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Presented in this paper is a cold formed steel load distribution system developed by iSPAN Systems LP that enables the installation of floor joists without the need to align them with the supporting wall studs. The floor joists are supported by a shear connection attached to a cold formed steel perimeter distribution member. In addition to the load distribution aspect, the system results in a simplified lateral design approach. An experimental verification study was carried out to establish the load distribution capability of the system, resulting in a simplified procedure to determine the connection requirements and load transfer characteristics to …

2012-08-24 University Graduate Committee Meeting Minutes, Morehead State University. Faculty Senate.

Faculty Senate Records

University Graduate Committee Meeting Minutes for August 24, 2012.

Business Innovation Group (Big) News, Georgia Southern University

Business Innovation Group: News & Publications

• Next ATDC/Creative Coast Seminar on Customer Value

First Recorded Introduction Of The Milliped Order Stemmiulida (Eugnatha: Nematophora): Potential Establishment In Florida, Usa, And New Records From Mexico; Northward Range Extension Into Southern Tamaulipas, Rowland M. Shelley, G. B. Edwards, Arthur E. Bogan

Insecta Mundi

Based on two “uni-ocellate” females, the world’s first introductions of the milliped order Stemmiulida are recorded from Florida, United States (US). One individual was collected in 1976 in Gainesville, Alachua County (Co.)., in northcentral peninsular Florida, and the other was taken in 1991 some 408 km (255 mi) to the south-southeast in Pompano Beach, Broward Co. The absence of further individuals and additional samples suggests that the introductions did not result in viable populations, and stemmiulidans are not presently established in the state; the Gainesville site was reinvestigated in 2012 without finding additional specimens. New records from Mexico include the …

A New Species Of Culcua Walker (Diptera: Stratiomyidae) From Vietnam, Norman E. Woodley

Insecta Mundi

A new species of Culcua Walker (Diptera: Stratiomyidae), C. lingafelteri Woodley, new species, is described from northern Vietnam. It is diagnosed relative to other species using the recent revision of the genus by Rozkošný and Kozánek (2007). This is the first species of Culcua reported from Vietnam

An Annotated List Of Symmachia Hübner, [1819] (Lepidoptera: Riodinidae: Symmachiini) From Parque Nacional Da Serra Do Divisor, Acre, Brazil, With The Description Of A New Species, Diego Rodrigo Dolibaina, Luis Anderson Ribeiro Leite, Fernando Maia Silva Dias, Olaf Hermann Hendrik Mielke, Mirna Martins Casagrande

Insecta Mundi

We provide an illustrated list of species belonging to the genus Symmachia Hübner, [1819] (Lepidoptera: Riodinidae: Symmachiini) collected during an expedition conducted between September 10-21, 2011 in the northern part of the Parque Nacional da Serra do Divisor, Acre, Brazil, a remote region of Amazon rainforest. A total of 46 individuals were collected belonging to 15 species. For all recorded species, drawings of male genitalia and behavioral information are provided to support future studies on the taxonomy of the group. A new species, Symmachia divisora Dolibaina and Leite, sp. nov., is described, and a revised status for Symmachia hetaerina hesione …

The Junior Scientist Outreach Program Handbook: A Guide To The Preparation, Execution, And Evaluation Of A Sustainability-Themed Informal Science Education Outreach Program, Martha Josefina Vargas

Biology Faculty & Staff Publications

This handbook is intended to provide the history of and methodology for the preparation, execution and evaluation of an informal science education program that is based in a predominantly Hispanic community in Albuquerque, New Mexico. Because this program, known as The Junior Scientist Outreach Program (JSOP), has already positively impacted the lives of hundreds of students and families, the importance and relevance of its continuation will be highlighted and reiterated throughout the instructions and step-by-step procedures.

Mammalogy Class 2012 Catalog, Evan Fahy

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Julie Hawk

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Amber Howard

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Andrea Jackson

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Specimen Catalog & Field Notes, Bethany L. Abrahamson

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Combined Catalogs & Field Notes - Part Iii, Michael Smith, Rosemary Steinberg, Heather Toman, Amber West, Marie Westorer, Kristin Wright

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Combined Catalogs & Field Notes - Part Ii, Valerie Hovda, Andrea Jackson, Teryn Jensen, Amanda Jones, Schuyler Liphardt, Kevin Mccormick

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Kristin Wright

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Schuyler Liphardt

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Rosemary Steinberg

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Michael Smith

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Amanda Jones

Division of Mammals - Field Notes and Catalogs

No abstract provided.

Mammalogy Class 2012 Catalog, Heather Toman

Division of Mammals - Field Notes and Catalogs

No abstract provided.