Heat Transfer, Combustion Commons^™

A Systematic Investigation Of Condensation Heat Transfer Using Asymmetric Micro-Scale Surfaces, Emily Brown

LSU Master's Theses

Asymmetric surfaces been shown to inducing unidirectional motion in the Leidenfrost regime; however, very minimal research has been conducted to investigate whether these surface can enhance condensation through the same means. The investigation of heat transfer of ratchets in condensation is a relatively untapped area of study, specifically ratchets with superhydrophobic properties. Anticipated difficulty lies in creating surfaces features or coatings that retain the ratchets and can adequately sustain optimal wetting state of Cassie-Baxter required to improve heat transfer performance during condensation. This study serves to investigate whether ratchets are a feasible surface feature to enhance condensation heat transfer. First, …

Large Eddy Simulations Of Vertical Jets In Crossflow, Pranaya Pokharel

LSU Doctoral Dissertations

Jets in crossflow (JICF) have applications ranging from oil spill to film cooling of turbine blades. Hence, an understanding of the flow physics is important. The majority of the research has been conducted for low velocity ratios between jet and crossflow with round jets. JICF is demonstrated to behave differently for high velocity ratios and different jet shapes. Circular and rectangular jets are commonly used in aircraft applications. Current study focuses on high velocity ratio JICF issuing from both circular and rectangular exit.

For simulating JICF, an in house code “Chem3D” is used with Large Eddy Simulation (LES) to model …

Combustion Dynamics And Heat Transfer In An Ultra Compact Combustor, Brian T. Bohan

Theses and Dissertations

The Ultra Compact Combustor (UCC) is an innovative combustion system alternative to a traditional turbine engine burner with the potential to improve engine efficiency with a reduced combustor volume. The UCC shortens the axial length of the combustor, and therefore reduces engine weight, by burning in an annulus and swirling the reactants in the circumferential direction. These length and weight improvements can directly lead to an increased thrust-to-weight rating of the engine. The present research included five objectives which advanced the UCC concept on four fronts; cooling UCC turbine vanes, advanced computational modeling of UCC systems, system air split control …

Micro Combustion Of Primary Reference Fuels In Narrow Heated Channels, Veerendra Naralasetti

LSU Master's Theses

Conventional fuel testing machines like CFR engines require large quantities of fuel. The current study seeks to overcome this limitation by introducing an alternative method using a microscale combustion reactor which consumes relatively small amounts of fuel (100-250 ml). For this reason, Primary Reference Fuels (PRF’s: volumetric mixtures of n-heptane and iso-octane) which are simple surrogates of gasoline are selected to test using micro reactor. The primary goal is to determine the effectiveness of using the micro reactor setup to differentiate fuels of different octane number. Experiments with stoichiometric PRF/air mixtures are performed inside a cylindrical quartz tube of 1mm …

Waste Heat Recovery From A Vented Electric Clothes Dryer Utilizing A Finned-Tube Heat Exchanger, Abdul Raheem A. Shaik, Stephen L. Caskey, Eckhard A. Groll

The Summer Undergraduate Research Fellowship (SURF) Symposium

Conventional residential clothes dryers continuously vent moist, hot air during the drying process. The vented air leaves the home but still has useful temperature and humidity that could be recovered to offset other heating demands in the home. A study is carried out to quantify the amount of heat extracted from the waste heat stream of a conventional, vented clothes dryer. To extract the heat, a water cooled, fin-and-tube heat exchanger is located within the exhaust duct. A steady state thermodynamic dry coil and wet coil model was built in Engineering Equation Solver (EES). The model accounts for the heat …

Thermophotovoltaic Devices: Combustion Chamber Optimization And Modelling To Maximize Fuel Efficiency, Arnold Chris Toppo, Ernesto Marinero, Zhaxylyk Kudyshev

The Summer Undergraduate Research Fellowship (SURF) Symposium

Currently, 110 billion cubic meters of natural gas (primarily methane), a potent greenhouse gas, are flared off for environmental and safety reasons. This process results in enough fuel to provide the combined natural gas consumption of Germany and France. The research team developed a thermophotovoltaic device to convert thermal energy to electricity at a high efficiency using proprietary emitters and combustion system. With the current focus being fuel efficiency and the combustion process, the assembly was simulated using ANSYS Fluent modelling software and the following parameters were optimized: air/fuel ratios, flow rates, and inlet sizes. Simultaneously the heat transfer across …

Study Of The Effective Thermal Conductivity Of Polymer Composites With Varying Filler Arrangements, Debraliz Isaac Aragones, Rajath Kantharaj, Aaditya Candadai, Amy Marconnet

The Summer Undergraduate Research Fellowship (SURF) Symposium

Alternative thermal management solutions for electronic devices are being widely explored due to the increasing heat concentration that results from shrinking sizes and increasing power of modern electronics. Clearly, there is a need to spread the heat effectively in these systems, and polymer composites can potentially provide high thermal conductivity at low filler fraction while maintaining desirable mechanical properties for electronic packaging. The present study aims to investigate the effective thermal conductivity of various copper filler arrangements in a polymer matrix. The polymer composites are fabricated using laser cut acrylic templates to embed aligned copper rods in epoxy and create …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

3d Numerical Study Of Multiphase Counter-Current Flow Within A Packed Bed For Post Combustion Carbon Dioxide Capture, Li Yang, Fang Liu, Zhengchang Song, Kunlei Liu, Kozo Saito

Mechanical Engineering Faculty Publications

The hydrodynamics within counter-current flow packed beds is of vital importance to provide insight into the design and operational parameters that may impact reactor and reaction efficiencies in processes used for post combustion CO₂ capture. However, the multiphase counter-current flows in random packing used in these processes are complicated to visualize. Hence, this work aimed at developing a computational fluid dynamics (CFD) model to study more precisely the complex details of flow inside a packed bed. The simulation results clearly demonstrated the development of, and changes in, liquid distributions, wetted areas, and film thickness under various gas and liquid …

Transient Heat Storage Systems, Ian M. Sweeney, Brock M. Johnson, Todd K. Lundberg

Mechanical Engineering

Phase change materials (PCM) have many applications in transient cooling systems, including those with high transient heat loads and low duty cycles. These materials allow a system to remain within a narrow temperature range with a relatively low weight compared to conventional heat sinks or high-power cooling systems. This senior capstone project includes the design of a PCM based thermal energy storage system to integrate into an existing cooling loop, as well as a determination of viable PCM’s for the application. This report contains the necessary information to build the test apparatus.

Finite-Difference Modeling Of The Batch Process Smoldering Combustion Of Wastewater, Laura H. Kawashiri

Master's Theses

A MATLAB model was developed for the smoldering combustion of wastewater in the context of a decentralized residential wastewater treatment appliance. Data from a batch process sewage smoldering experiment was simulated using implicit finite-difference approximations, assuming one-dimensional transient conductive heat transfer. The time-dependent temperature profiles within the column represented the main parameters of interest and were used to verify recoverable heat energy estimations. Given that the modeling method used for this thesis represents a unique approach, the assumptions and limitations of this model are thoroughly described in the context of reproducing results for other smoldering setups. A lack of convergence …

Thermal Modelling And Validation Of Heat Profiles In An Rf Plasma Micro-Thruster, Alec Sean Henken

Master's Theses

The need and demand for propulsion devices on nanosatellites has grown over the last decade due to interest in expanding nanosatellite mission abilities, such as attitude control, station-keeping, and collision avoidance. One potential micro-propulsion device suitable for nanosatellites is an electrothermal plasma thruster called Pocket Rocket. Pocket Rocket is a low-power, low-cost propulsion platform specifically designed for use in nanosatellites such as CubeSats. Due to difficulties associated with integrating propulsion devices onto spacecraft such as volume constraints and heat dissipation limitations, a characterization of the heat generation and heat transfer properties of Pocket Rocket is necessary. Several heat-transfer models of …

Heat Flow Characterization Of Speakers, Sabrina M. Gough, Lydia K. Hedge, Nicolas M. Jones

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Driver Cooling System, Joseph Fatin Bolous, Jake Donald Deboer, Alvin Theodore Lau

Mechanical Engineering

This document provides our Final Design Review (FDR) for the Driver Cooling System Project. It contains our background research, which includes current product research, technical research, and information on our sponsor’s needs as a customer as well our manufacturing process, test results, and final design. We created a problem statement to define the scope of the project, discuss sponsor and consumer needs and wants, and technical specifications. After brainstorming, we ultimately selected a thermoelectric cooling system (TEC) after presenting our Preliminary Design Report and Critical Design Report. We built the final prototype, as can be seen in the manufacturing plan, …

3-Dimensional Automated Heat Flux Calibration Device, Victor Raul Chacon, David Madison Morrisset, Alex Michael Schnorr, Kevin Scott

Mechanical Engineering

This document aims to describe the problems in current radiant heat source heat flux calibration techniques and the approach our team took to solve them through automation. The following sections outline the basic premise of the problem we addressed and who our end product benefited. The proceeding sections addresses the research that we have performed regarding heat flux measurements and automation. This research includes current solutions – mostly partial solutions for problems that are similar but not exactly like ours. Following the background research, we define objectives, with specific details that outline how we evaluated different possible solutions, and how …

Upgrading The Sr-30 Miniature Turbojet For Adaptable Exhaust, Shannon Ferreira, Erin Mcmurchie, Peter Pratt

Mechanical Engineering

The California Polytechnic State University, San Luis Obispo (Cal Poly, SLO) Aerospace Department is requesting a variable nozzle adaptation for their SR-30 turbojet engine. The nozzle is intended for laboratory use in sophomore and junior level courses to supplement instruction on the effects that exhaust behavior has on the performance of propulsion technologies. Topics covered during a performance study of the SR-30 turbojet engine will include, but are not limited to: Brayton Cycle analysis, turbojet operation in ideal and non-ideal test conditions, instrumentation limitations, and basic nozzle operation. The SR-30 turbojet engine is similar in design and operation to engines …

Bubble Nucleation In Superhydrophobic Microchannels Due To Subcritical Heating, Adam Cowley, Daniel Maynes, Julie Crockett, Brian D. Iverson

Faculty Publications

This work experimentally studies the effects of single wall heating on laminar flow in a high-aspect ratio superhydrophobic microchannel. When water that is saturated with air is used as the working liquid, the non-wetted cavities on the superhydrophobic surfaces act as nucleation sites and allow air to effervesce out of the water and onto the surface when heated. Previous works in the literature have only considered the opposite case where the water is undersaturated and absorbs air out the cavities for a microchannel setting. The microchannel considered in this work consists of a rib/cavity structured superhydrophobic surface and a glass …

Temperature And Stress Analysis During Tank Decanting And Refilling Process, Zhe Liu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

In the present work, an analytical expression for the temperature distribution of the cross-section of a natural gas transport tank is derived by time-matching Green’s Function method. The tank decanting process can produce a living temperature decrease inside the tank wall while the filling process can produce a large temperature increase. This behavior can cause damage to the inner layer of the tank. The damage occurs in the form of excessive stress in the wall which is combined mechanical stress and thermal stress. Therefore, thermo-elasticity analysis is another objective of the present work. A simplified mechanical model is established in …

Experimental And Numerical Comparison Of Wort Cooling Methods During The Homebrewing Process, Zachary Hammond

Renée Crown University Honors Thesis Projects - All

Homebrewing, the process of making beer for personal consumption, has been legal in the United States since 1978 and allowed beer enthusiasts to experiment with new beer styles at a low cost. Although the procedure is relatively straightforward, it can be very timeconsuming without expensive equipment. The longest step in brewing is wort cooling, where the non-alcoholic beer, or wort, is cooled from boiling temperatures to near room temperature for fermentation. Improper or slow cooling can not only be monotonous but result in contamination or haze in the final product. Wort chillers, which generally cost anywhere from $50 to $500, …